Kent Euroclean SelectGloss 21PH, SelectGloss 21PK, SelectGloss 27PO, SelectGloss 27PR, SelectGloss 27PK Operator's Manual And Parts List

Electronic Service

Manuals

This electronic document is provided as a service to our custom­ers. We do not create the contents of the information contained in
this document. Should you have detailed questions pertaining to
the information contained in this document, you may contact Michco,
or the manufacturer which provided the original information in this
electronic deliverable. Michco’s only part in this electronic deliver­able was the electronic assembly process.

You may contact Michco through the following methods:

Phone [phone] or [phone] MI, OH, IN only

2011 N. High St. -- Lansing, Michigan -- 48906

Fax: [phone]

Email: [e-mail]

Web site: www.Michco.Com

Parts Web site: www.FloorMachineParts.Com

Order Parts on Line at:

www.FloorMachineParts.Com

Directly to Parts & Service:

By Email: [e-mail]

By Fax: [phone]

By Voice: Use numbers above.

Serving the Cleaning Industry Since 1922

Notice: All copyrighted material remains property of original owners, all trademarks are property of respective
owners. Manuals are subject to Manufacturer’s reproduction limitations. Originals or reproductions were provided
by manufacturers through a request. We make no warranty as to the correctness of information provided in this
document and you assume all risk.

SelectGloss™ 21PH, 21PK
SelectGloss™ 27PK, 27PO, 27PR

OPERATOR MANUAL AND PARTS LIST

Kent/Euroclean MODELS 56649654(21PH), 56649655(21PK)
56649656(27PK), 56649657(27PO / OBS), 56649930(27PR)

10/02 revised 5/04 Form Number 56041536

IMPORTIMPORT

IMPORT

IMPORTIMPORT

This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices
other than normal residential housekeeping purposes.

Please read and adhere to all of the following Instructions before operating propane equipment.

1 The fuel supply system and cylinder connections of the floor maintenance machine shall be checked for leakage

immediately after a cylinder is connected.

2 Connection and disconnection of cylinders shall be done in a well ventilated area with no source of ignition with

10 ft. (3m) from the point of connection.
3 When the engine of a floor maintenance machine is running the operator shall not leave the unit unattended.
4 When a floor maintenance machine is not in use and stored indoors, the cylinder shall be removed and stored

outdoors and protected from damage and tampering.
5 A sign indicating “NO SMOKING” shall be permanently displayed at the storage area. The sign shall be in

accordance with the sign required In Clause10.12.3 of CAN/CGA-b149.2-M91, Propane Installation Code. (Does not

apply in industrial buildings).
6 When the cylinder is attached to the floor maintenance machine for use, the operator shall not leave the unit

unattended except for short periods of time such as rest stops, washroom or meal stops.
7 A floor maintenance machine shall only be used In buildings:

a. provided with continuous mechanical ventilation that removes the products of combustion to the outdoors of not

b provided with natural ventilation of not less than 300 CFM for each 10,000Btu input or fraction thereof, based on

ANT SAFETY INSTRUCTIONSANT SAFETY INSTRUCTIONS

ANT SAFETY INSTRUCTIONS

ANT SAFETY INSTRUCTIONSANT SAFETY INSTRUCTIONS

AA

TTENTION!TTENTION!

A

TTENTION!

AA

TTENTION!TTENTION!

less than 300 CFM for each 10,000 Btu input or fraction thereof;

a maximum of one quarter air change per hour for the net building volume.

8 The owner of a floor maintenance machine must ensure that the operator has participated in a course authorized

by the manufacturer of the unit on the safe handling of propane and the safe operation of the machine.
9 The owner of a floor maintenance machine shall ensure that the unit is maintained in accordance with the

manufacturer’s recommended maintenance procedures in a safe operating condition and the owner shall

maintain a record of the maintenance for a period of two years.

10 Before transporting a floor machine, the cylinder shall be securely fastened, with the system valve closed and the

cylinder shall be located in a well ventilated space.

SASA

VE THESE INSTRUCTIONSVE THESE INSTRUCTIONS

SA

VE THESE INSTRUCTIONS

SASA

VE THESE INSTRUCTIONSVE THESE INSTRUCTIONS

2 2

2 - FORM NO. 56041536 - SelectGloss™ 21PH, 21PK, 27PK, 27PO, 27PR

2 2

SAFETY PRECAUTIONSSAFETY PRECAUTIONS

SAFETY PRECAUTIONS

SAFETY PRECAUTIONSSAFETY PRECAUTIONS

This LPG (Liquefied Petroleum Gas) machine is intended for commercial

use; It is designed to clean floors. Do not use the machine other than

described in this Operator Manual.

All operators must read, understand and practice the following safety

precautions:

The following safety alert symbol is used throughout this manual as

indicated in their descriptions.

WW

ARNING!ARNING!

W

ARNING!

WW

ARNING!ARNING!

To warn of hazards or unsafe practices that could result In

severe personal Injury or death.

CAUTION!CAUTION!

CAUTION!

CAUTION!CAUTION!

To Identify actions that must be followed for safety opera-

tion of equipment.

The following information signals potentially dangerous conditions to

the operator of equipment.

1. DO NOT OPERATE:1. DO NOT OPERATE:

1. DO NOT OPERATE:

1. DO NOT OPERATE:1. DO NOT OPERATE:
* Unless trained and authorized.
* Unless operator manual Is read and understood.
* If It Is not In proper operating condition.

2. BEFORE OPERATING MACHINE:2. BEFORE OPERATING MACHINE:

2. BEFORE OPERATING MACHINE:

2. BEFORE OPERATING MACHINE:2. BEFORE OPERATING MACHINE:
* Check for fuel oil and liquid leaks. If leakage Is detected, shut off

fuel supply at tank Immediately.
* Keep sparks and open flame away from refueling area.
* Make sure area Is well ventilated.
* Remove any loose objects on floor .

4. BEFORE LEAVING MACHINE:4. BEFORE LEAVING MACHINE:

4. BEFORE LEAVING MACHINE:

4. BEFORE LEAVING MACHINE:4. BEFORE LEAVING MACHINE:
* Stop on level surface.
* Remove key (If applicable).
* Turn off LPG valve on tank.

5. WHEN SERVICING MACHINE:5. WHEN SERVICING MACHINE:

5. WHEN SERVICING MACHINE:

5. WHEN SERVICING MACHINE:5. WHEN SERVICING MACHINE:
* Keep hair, hands, feet, clothing, etc., away from moving parts.
* Wear eye and ear protection when using pressurized air or

water .

* Keep flames and sparks away from fuel system service area.

Keep area well ventilated.
* Do not smoke or allow smoking In the vicinity.
* Never use non-U.L. listed fuel tank or component as a substitute.
* Use manufacturer supplied or approved replacement parts.

WW

ARNING!ARNING!

W

ARNING!

WW

ARNING!ARNING!

Engine emits toxic gases. Severe respiratory damage or
asphyxiation can result. Provide adequate ventilation.
Consult with your regulatory authorities for exposure lim­its. Keep engine properly tuned.

WW

ARNING!ARNING!

W

ARNING!

WW

ARNING!ARNING!

LP gas Is extremely flammable and is explosive under
certain conditions.

WW

ARNING!ARNING!

W

ARNING!

WW

ARNING!ARNING!

Machine moves when motor is running. Stop motor before
leaving machine.

WW

ARNING!ARNING!

W

ARNING!

WW

ARNING!ARNING!

Do not store machine outdoors and avoid getting wet.

WW

ARNING!ARNING!

W

ARNING!

WW

ARNING!ARNING!

The use of supplies other than those recommended by
manufacturer may cause damage.

3. WHEN OPERATING MACHINE:3. WHEN OPERATING MACHINE:

3. WHEN OPERATING MACHINE:

3. WHEN OPERATING MACHINE:3. WHEN OPERATING MACHINE:
* Always wear eye protection.
* Always use extreme caution when maneuvering.
* If you smell gas: shut off LPG valve immediately, open windows,

do not touch any electrical switches, extinguish any open flame

and immediately call your gas supplier .
* Do not smoke or allow smoking in the vicinity.
* Go slow on inclines and slippery surfaces.
* Do not place flammable objects such as fuel, matches, etc., close

to the engine.
* Report machine damage or faulty operation immediately.
* Do not run continually over one minute In the park or tilted back

position, longer periods will affect oil flow and cause damage to

the engine.
* Be careful not to touch the muffler.
* Do not leave machine unattended while engine Is running.
* Keep hands, feet, hair, and loose clothing, etc. away from revolv-

ing pad and pulleys.
* Do not attempt to change pad while engine Is running.

FORM NO. 56041536 - SelectGloss™ 21PH, 21PK, 27PK, 27PO, 27PR -

33

3

33

TT

ABLE OF CONTENTSABLE OF CONTENTS

T

ABLE OF CONTENTS

TT

ABLE OF CONTENTSABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONS

SAFETY PRECAUTIONSSAFETY PRECAUTIONS

SAFETY PRECAUTIONS

SAFETY PRECAUTIONSSAFETY PRECAUTIONS
INTRODUCTIONINTRODUCTION

INTRODUCTION

INTRODUCTIONINTRODUCTION
MACHINE SETUPMACHINE SETUP

MACHINE SETUP

MACHINE SETUPMACHINE SETUP

CHECKING OIL LEVEL AND FILTERS .......................................... 5

ADJUSTING HANDLE HEIGHT .................................................... 5

INSTALLING OR CHANGING LPG FUELTANK .......................... 5

INSTALLING OR REMOVING

PAD DRIVER AND PADS .............................................................. 5

MACHINE OPERATIONMACHINE OPERATION

MACHINE OPERATION

MACHINE OPERATIONMACHINE OPERATION

STARTING MACHINE ................................................................... 6

OPERATING ELECTRIC CLUTCH (OPTIONAL)........................... 6

STOPPING MACHINE ................................................................... 6

EMERGENCY STOPPING .............................................................. 6

WHILE OPERATING MACHINEWHILE OPERATING MACHINE

WHILE OPERATING MACHINE

WHILE OPERATING MACHINEWHILE OPERATING MACHINE

MAINTENANCEMAINTENANCE

MAINTENANCE

MAINTENANCEMAINTENANCE

DAILY MAINTENANCE ................................................................. 7

WEEKLY MAINTENANCE ............................................................. 7

MONTHLY MAINTENANCE ......................................................... 7

QUARTERLY MAINTENANCE ...................................................... 7

LIFE OF MACHINE ......................................................................... 7

FUEL SYSTEM ................................................................................ 7

CHANGING THE OIL ...................................................................... 7

ADJUSTING BELT TENSION ....................................................... 8

REFUELING AND STORING TANKSREFUELING AND STORING TANKS

REFUELING AND STORING TANKS

REFUELING AND STORING TANKSREFUELING AND STORING TANKS

REFUELING LP GAS TANKS......................................................... 9

STORING LP GAS TANKS ............................................................ 9

............................................................................................................................

..............................................................

............................................................................................................................

......................................................................................................................................................

...........................................................................

......................................................................................................................................................

................................................................................................................................................

........................................................................

................................................................................................................................................

..............................................................................................................................

...............................................................

..............................................................................................................................

......................................................................................................................................................

...........................................................................

......................................................................................................................................................

..............................................................................

.......................................

..............................................................................

......................................................................................................

...................................................

......................................................................................................

......................................................................................

...........................................

......................................................................................

INTRODUCTIONINTRODUCTION

INTRODUCTION

INTRODUCTIONINTRODUCTION

This manual will help you get the most from your

22

2

22

SelectGloss™SelectGloss™

SelectGloss™. Read it thoroughly before operating the machine.

SelectGloss™SelectGloss™
This product is intended for commercial use only.

33

3

33

PP

ARTS AND SERVICEARTS AND SERVICE

P

ARTS AND SERVICE

PP

44

4

44
55

5

55

66

6

66

66

6

66

77

7

77

88

8

88

ARTS AND SERVICEARTS AND SERVICE

Repairs, when required, should be performed by Kent / Euroclean
service personnel using Kent / Euroclean original replacement parts
and accessories.

Call Kent / Euroclean for repair parts or service. Please specify the
Model and Serial Number when discussing your machine.

NAME PLANAME PLA

NAME PLA

NAME PLANAME PLA

The Model and Serial Number of your machine are shown on the
Nameplate on the machine. This information is needed when ordering
repair parts for the machine. Use the space below to note the Model and
Serial Number of your machine for future reference.

MODEL NUMBER

SERIAL NUMBER

UNCRAUNCRA

UNCRA

UNCRAUNCRA

When the machine is delivered, carefully inspect the shipping carton
and the machine for damage. If damage is evident, save the shipping
carton so that it can be inspected. Contact the Kent / Euroclean
Customer Service Department immediately to file a freight damage
claim.

TETE

TE

TETE

TINGTING

TING

TINGTING

Kent / Euroclean™Kent / Euroclean™

Kent / Euroclean™

Kent / Euroclean™Kent / Euroclean™

STORING MACHINESTORING MACHINE

STORING MACHINE

STORING MACHINESTORING MACHINE
TRANSPORTING MACHINETRANSPORTING MACHINE

TRANSPORTING MACHINE

TRANSPORTING MACHINETRANSPORTING MACHINE

TROUBLE SHOOTING GUIDETROUBLE SHOOTING GUIDE

TROUBLE SHOOTING GUIDE

TROUBLE SHOOTING GUIDETROUBLE SHOOTING GUIDE
STANDARD PARTSSTANDARD PARTS

STANDARD PARTS

STANDARD PARTSSTANDARD PARTS

21PH HONDA .................................................................................. 12

21PK KAWASAKI ........................................................................... 12

27PO ONAN P248 (20HP) .............................................................. 14

27PK KAWASAKI ........................................................................... 14

27PR ROBIN .................................................................................... 16

ROBIN ZXV 653 ENGINE ............................................................... 18

ROBIN ZXV 653 CARBURETION SYSTEM ................................. 20

KAWASAKI AUTOMATIC SHUT DOWN SYSTEM ................... 22

HONDA FUEL SYSTEM ................................................................. 24

KAWASAKI FUEL SYSTEM .......................................................... 25

ROBIN FUEL SYSTEM ................................................................... 26

ELECTRIC CLUTCH ASSY ............................................................. 27

KILL SWITCH ASSY ....................................................................... 28

KAWASAKI FUEL LOAD BLOCK .................................................. 29

KAWASAKI SCHEMATIC & HARNESS ...................................... 30

........................................................................................................................................

....................................................................

........................................................................................................................................

................................................................................................................

........................................................

................................................................................................................

............................................................................................................

......................................................

............................................................................................................

1010

10

1010
1010

10

1010

1111

11

1111

4 4

4 - FORM NO. 56041536 - SelectGloss™ 21PH, 21PK, 27PK, 27PO, 27PR

4 4

revised 03-6

MACHINE SET UPMACHINE SET UP

MACHINE SET UP

MACHINE SET UPMACHINE SET UP

-

5 Unlatch and remove empty LPG fuel tank from machine and

store tank in a designated, safe area.

CHECKING OIL LEVEL AND FILCHECKING OIL LEVEL AND FIL

CHECKING OIL LEVEL AND FIL

CHECKING OIL LEVEL AND FILCHECKING OIL LEVEL AND FIL

1 Check oil level prior to starting machine. Use proper amount and

specified oil, in order to prevent engine damage. When filling or

changing oil, add more than one quart (946.3ml) -then check dip

stick In cap. Add additional oil If necessary but do not overfull

The manufacturer recommends the use of 10W30 oil. ALWAYS CHECK
OIL DAILY BEFORE USING MACHINE.

AA

TTENTION!TTENTION!

A

TTENTION!

AA

TTENTION!TTENTION!

When checking oil, machine should be turned OFF and on level surface.
Remove dipstick and wipe clean, then replace dipstick. For Honda,
Kawasaki and Robin the cap should not be screwed In. To check Onan
engine, the cap must be screwed In all the way. ALWAYS REFER TO YOUR
ENGINE MANUAL.

2 Be sure air filter Is free of dust/debris and other obstructions.
3 Check and clean recoil and carburetor filters If necessary. (See

Engine Owners Manual)

ADJUSTING HANDLE HEIGHTADJUSTING HANDLE HEIGHT

ADJUSTING HANDLE HEIGHT

ADJUSTING HANDLE HEIGHTADJUSTING HANDLE HEIGHT

Machine is equipped with an adjustable handle for comfort and use of
operators of different heights. With a 9/16" wrench, simply adjust handle
at pivot points until desired operating position Is reached and then
retighten bolts.

TERSTERS

TERS

TERSTERS

6 Carefully put full LPG tank on machine and position valve nozzle

towards engine.

NOTE: Make sure LPG fuel tank matches fuel system (Vapor System
Only).

CAUTION!CAUTION!

CAUTION!

CAUTION!CAUTION!

Never use a fuel tank not Intended for machine.

7 Fasten tank hold-down clamp to securely lock tank in position.

Adjustment to hold-down clamp can be made by threading latch
in or out.

8 Connect LPG fuel hose to valve nozzle by turning service cou-

pling clockwise (Tighten according to tank supplier recommen­dations). Make sure service coupling Is clean and free of
damage. Also, make sure It matches machine service coupling.

AA

TTENTION!TTENTION!

A

TTENTION!

AA

TTENTION!TTENTION!

When Installing tank, be careful not to cross thread service
coupling.

9 Open tank service valve slowly and check for leaks. Close

service valve immediately if a LPG leak Is detected.

INSTINST

ALLING OR CHANGING LPG FUELALLING OR CHANGING LPG FUEL

INST

ALLING OR CHANGING LPG FUEL

INSTINST

ALLING OR CHANGING LPG FUELALLING OR CHANGING LPG FUEL

TT

ANKANK

T

ANK

TT

ANKANK

NOTE: For refueling tank,

1 Push machine In a designated safe area.

NOTE: Move to Step 6 for tank installation.

2 Close LPG tank valve on installed tank.

3 Operate engine until it stops from lack of fuel. (See Machine

Owners Operation)

FOR SAFETY: Never release or bleed tank Inside building or en-FOR SAFETY: Never release or bleed tank Inside building or en-

FOR SAFETY: Never release or bleed tank Inside building or en-

FOR SAFETY: Never release or bleed tank Inside building or en-FOR SAFETY: Never release or bleed tank Inside building or en­closed areas.closed areas.

closed areas.

closed areas.closed areas.
FOR SAFETY: When servicing machine, keep flames and sparksFOR SAFETY: When servicing machine, keep flames and sparks

FOR SAFETY: When servicing machine, keep flames and sparks

FOR SAFETY: When servicing machine, keep flames and sparksFOR SAFETY: When servicing machine, keep flames and sparks
away from fuel system service area. Keep area well ventilated.away from fuel system service area. Keep area well ventilated.

away from fuel system service area. Keep area well ventilated.

away from fuel system service area. Keep area well ventilated.away from fuel system service area. Keep area well ventilated.

4 Put on gloves and remove service coupling by turning counter-

clockwise.

see

“REFUELING AND STORING TANKS”.

INSTINST

ALLING OR REMOVING PALLING OR REMOVING P

INST

ALLING OR REMOVING P

INSTINST

ALLING OR REMOVING PALLING OR REMOVING P

AND PAND P

AND P

AND PAND P

Consult an authorized distributor to assist you in choosing the correct
pad for your specific cleaning need.

Pad Driver Installation:Pad Driver Installation:

Pad Driver Installation:

Pad Driver Installation:Pad Driver Installation:

1 Lean machine on left side (Dip stick tube down).
2 Place pad driver on drive shaft and spin pad driver clockwise to

Pad Installation:Pad Installation:

Pad Installation:

Pad Installation:Pad Installation:

1 Tilt machine back on the rear caster (Park Position).
2 Remove plastic centerlock ring from pad driver. Center pad on

Pad Driver Removal :Pad Driver Removal :

Pad Driver Removal :

Pad Driver Removal :Pad Driver Removal :

1 With knee, apply downward pressure on bell of machine deck.
2 Place 3/4" (19 mm). Open end wrench onto top of drive shaft.
3 With rubber mallet, strike wrench to break loose shaft from pad

4 Lean machine on left side (Dip stick tube down).
5 Remove pad driver by spinning off counter-clockwise.

ADSADS

ADS

ADSADS

install.

pad driver and secure with centerlock ring.

driver (counter-clockwise).

AD DRIVERAD DRIVER

AD DRIVER

AD DRIVERAD DRIVER

revised 03-7

FORM NO. 56041536 - SelectGloss™ 21PH, 21PK, 27PK, 27PO, 27PR -

55

5

55

MACHINE OPERAMACHINE OPERA

MACHINE OPERA

MACHINE OPERAMACHINE OPERA

FOR SAFETY: Do Not operate machine unless Operation Manual is read
and understood.

STST

ARTING MACHINEARTING MACHINE

ST

ARTING MACHINE

STST

ARTING MACHINEARTING MACHINE

1 With machine on level surface. check oil level prior to starting

machine.

2 Tilt machine back onto rear caster (Park Position).

3 Remove any packing materials and obstructions from drive

system.

4 Turn LPG fuel knob ON tank. Check LPG gas level meter.

NOTE:NOTE:

NOTE: Opening service valve too quickly may cause service check valve

NOTE:NOTE:
to stop flow of LPG fuel. If check valve stops fuel flow, close service
valve, wait a few seconds and open valve slowly again.

5 Push throttle lever to choke position for Honda engine only. All

other engines start in IDLE position.

TIONTION

TION

TIONTION

STOPPING MACHINESTOPPING MACHINE

STOPPING MACHINE

STOPPING MACHINESTOPPING MACHINE

1 Turn LPG valve OFF at tank while running. This serves to purge

or bleed fuel hoses and carburetor system of fuel, so that there
is no danger of gas escaping from lines when tank is removed for
outside storage.

2 Tilt machine back on rear caster .

3 Engine will stop running when fuel lines bleed clear.

4 Pull throttle lever to STOP position after engine has stopped.

5 Turn key off if equipped.

EMERGENCY STOPPINGEMERGENCY STOPPING

EMERGENCY STOPPING

EMERGENCY STOPPINGEMERGENCY STOPPING

1 Pull throttle back to STOP OR turn off key if equipped.

2 Turn LPG valve OFF at tank.

NOTE:NOTE:

NOTE: Engine may back fire when stopped in this manner.

NOTE:NOTE:

6 Press start button OR turn key (if required) to engage starter. Do

not engage starter button for more than 20 seconds at a time. If
starter overheats it trips an internaI overload switch and will not
crank over. Wait at least 20 to 30 seconds between tries. When
engine starts, ease throttle back to running position. Do not hold
starter button in a continuous ON position, starter will burn out.

NOTE:NOTE:

NOTE: For Electric Clutch model, see “OPERATING ELECTRIC CLUTCH”.

NOTE:NOTE:

CAUTION!CAUTION!

CAUTION!

CAUTION!CAUTION!

Be careful not to allow the machine to come in contact with loose tiles
or other loose materials, remember the pad driver Is moving at very high
speed, and Injury can occur to the operator or passers by If pad driver
flings the loose material.

OPERAOPERA

OPERA

OPERAOPERA
TIONAL)TIONAL)

TIONAL)

TIONAL)TIONAL)

1 Once engine starts, move throttle control to SLOW rpm.

2 With throttle in SLOW, engage clutch by squeezing trigger

3 After clutch is engaged, move throttle to 3/4 throttle position and

TING ELECTRIC CLUTCH (OP-TING ELECTRIC CLUTCH (OP-

TING ELECTRIC CLUTCH (OP-

TING ELECTRIC CLUTCH (OP-TING ELECTRIC CLUTCH (OP-

switch.

then lower pad driver to floor.

If machine is equipped with Kill Switch Option, activate switch.

WHILE OPERAWHILE OPERA

WHILE OPERA

WHILE OPERAWHILE OPERA

WW

ARNING!ARNING!

W

ARNING!

WW

ARNING!ARNING!

Exhaust contains poisonous carbon monoxide gas. Avoid
Inhalation of exhaust gases. Never operate machine in a
confined area without proper ventilation.

1 Refer to (SAFETY PRECAUTION: WHEN OPERATING MACHINE)

on page 4.

2 Do not run machine for more than 15 seconds in one spot or

damage will occur to the floor.

3 Do not leave unattended in idle position or with engine running

period. If machine needs to be idled for short periods, tilt
machine back and move throttle to idle. Machine should now
idle safely.

AA

TTENTION!TTENTION!

A

TTENTION!

AA

TTENTION!TTENTION!

Do not Idle more than 5 minutes, longer periods will affect
oil flow and will cause damage to the engine.

TING MACHINETING MACHINE

TING MACHINE

TING MACHINETING MACHINE

4 For easier maneuverability, always start on right side of aisle.

CAUTION!CAUTION!

CAUTION!

CAUTION!CAUTION!

Never engage clutch In fast run position or with pad driver
on floor, this will cause damage to clutch.

6 6

6 - FORM NO. 56041536 - SelectGloss™ 21PH, 21PK, 27PK, 27PO, 27PR

6 6

MAINTENANCEMAINTENANCE

MAINTENANCE

MAINTENANCEMAINTENANCE

WW

ARNING!ARNING!

W

ARNING!

WW

ARNING!ARNING!

Before attempting any maintenance procedures on ma­chine, stop on level surface, shut off machine and turn off
LPG valve at tank.

AA

TTENTION!TTENTION!

A

TTENTION!

AA

TTENTION!TTENTION!

Repairs and adjustments must be performed by authorized
and trained personnel.

To keep machine in good working condition, simply follow the daily,
weekly, and monthly maintenance procedures.

NOTE:NOTE:

NOTE: Always record maintenance and service.

NOTE:NOTE:

AA

TTENTION!TTENTION!

A

TTENTION!

AA

TTENTION!TTENTION!

Always keep machine free from dust and lint; the engine is
air cooled and for proper air flow to cool the engine, the
recoil filter must remain clean.

DAILY MAINTENANCE (Every 4 Hours of Operation)DAILY MAINTENANCE (Every 4 Hours of Operation)

DAILY MAINTENANCE (Every 4 Hours of Operation)

DAILY MAINTENANCE (Every 4 Hours of Operation)DAILY MAINTENANCE (Every 4 Hours of Operation)

1 Check oil level (Use 10W30 oil only).
2 Clean recoil filter .
3 Check belt tension by pinching belt together. Belt should only

depress 1/2" (13mm).
4 Clean all air filters by blowing out dust and dirt and/or washing

the foam filters (recoil and carburetor pre- filter) with warm,

sudsy water and rinsing clean.

carburetor filters.)

Do not oil foam or filter .
5 Make sure all components are secure and tight.
6 Check pad daily (clean or replace).
7 Clean machine.
8 For Dust Control models, clean dust collection bag.

WEEKLY MAINTENANCE (Every 20 Hours of Operation)WEEKLY MAINTENANCE (Every 20 Hours of Operation)

WEEKLY MAINTENANCE (Every 20 Hours of Operation)

WEEKLY MAINTENANCE (Every 20 Hours of Operation)WEEKLY MAINTENANCE (Every 20 Hours of Operation)

1 Check oil level. Change oil and filters at 50 hours of operation. Use

10W30 Motor Oil or other no ash motor oils designed for use in

propane engines. Use of non-recommended oil may void the

engine warranty.

See Engine Owners Manual for complete servicing details

2 Inspect carburetor air filter by removing wing nut and over on top

of carburetor. Replace if dry or deposits are present.
3 Check belt for tension. Tighten if loose. If worn, replace with

proper belt.

schematic for size of belt required.
4 Inspect and tighten nuts and bolts on engine and frame.
5 Examine all propane hoses and connections for leaks or wear.

Replace if necessary.
6 Grease wheels. Use white lithium grease only and use no more

than 1 pump of grease. More grease than recommended will

push seal and dust cover out, allowing dust and other foreign

materials into the bearings, shortening the life of the wheel

significantly.

Be sure filters are clean and dry before use.

(See “ADJUSTING BELT TENSION”).

(Be careful not to wet the paper

Refer to parts

MONTHLY MAINTENANCE (Every 80 hours of Operation)MONTHLY MAINTENANCE (Every 80 hours of Operation)

MONTHLY MAINTENANCE (Every 80 hours of Operation)

MONTHLY MAINTENANCE (Every 80 hours of Operation)MONTHLY MAINTENANCE (Every 80 hours of Operation)

1 Perform all daily and weekly services.
2 Torque the head bolts when engine is cold in a crisscross

pattern as per engine manufacturers specifications

gine Owners Manual).

3 Check valve clearance with cold engine as per engine manufac-

turers specifications

4 Torque valve cover as per engine manufacturers specifications

(See Engine Owners Manual).

5 Inspect spark plug. Replace if necessary.
6 Change oil and oil filter.
7 Inspect fuel hoses for leak (repair as needed).
8 Wash undercarriage of machine to remove all dust and debris.
9 To ensure proper ventilation, remove engine cover and clean

engine.

10 Replace air filter element and foam filter.

QUARTERLY MAINTENANCE (Every 250 Hours of Operation)QUARTERLY MAINTENANCE (Every 250 Hours of Operation)

QUARTERLY MAINTENANCE (Every 250 Hours of Operation)

QUARTERLY MAINTENANCE (Every 250 Hours of Operation)QUARTERLY MAINTENANCE (Every 250 Hours of Operation)

1 Perform all of the above maintenance procedures and have

engine checked by an Authorized Service Center.
2 Check air gap in electronic ignition coil.
3 Check valves with engine cold.

NOTE:NOTE:

NOTE: Consult Engine Manual for complete servicing and adjustments

NOTE:NOTE:

information.

LIFE OF MACHINELIFE OF MACHINE

LIFE OF MACHINE

LIFE OF MACHINELIFE OF MACHINE

1 Change oil regularly.
2 Clean recoil filter regularly.
3 Clean carburetor filter regularly.
4 Keep machine clean from dust and debris.

FUELSYSTEMFUELSYSTEM

FUELSYSTEM

FUELSYSTEMFUELSYSTEM

Adjustments for the air/fuel mixture must be made only by an Authorized
Service Center. Improper adjustments can cause high levels of carbon
monoxide emissions which may cause carbon monoxide poisoning or
it can lead to engine damage.

• Idle speed is adjusting by turning adjustment screw on regula-

tor.

• Fuel flow is adjusted by adjustment screw on carburetor spud-

in.

CHANGING THE OILCHANGING THE OIL

CHANGING THE OIL

CHANGING THE OILCHANGING THE OIL

The manufacturer recommendations 10W30 oil.

1 Run engine for five minutes to warm oil.
2 Make sure machine is on level surface. Locate oil drain plug on

rear of engine beside oil cap and remove by turning counter-

clockwise with wrench.
3 Allow oil to run into pan under machine. Allow to completely

drain.
4 Install drain plug and tighten drain plug by turning clockwise

with wrench.
5 Slowly add one quart (946.3 mi) of 10W30 Motor Oil. Then check

oil level with dip stick in oil fill cap. Add additional oil if neces-

sary.
6 Replace oil-fill cap assembly. Hand tighten only.

AA

TTENTION!TTENTION!

A

TTENTION!

AA

TTENTION!TTENTION!

Do not overfill and never run engine low on oil.

AA

TTENTION!TTENTION!

A

TTENTION!

AA

TTENTION!TTENTION!

When checking oil, be sure cap is fully screwed out and
free. Do not check oil by screwing cap in and then out again,
this will give you a false reading.

(See Engine Owners Manual).

(See En-

FORM NO. 56041536 - SelectGloss™ 21PH, 21PK, 27PK, 27PO, 27PR -

77

7

77

ADJUSTING BELT TENSIONADJUSTING BELT TENSION

ADJUSTING BELT TENSION

ADJUSTING BELT TENSIONADJUSTING BELT TENSION

REFUELING AND STORING TREFUELING AND STORING T

REFUELING AND STORING T

REFUELING AND STORING TREFUELING AND STORING T

ANKSANKS

ANKS

ANKSANKS

Tools required:

• 3/4" (19mm) open end wrench

• 15/16" (24mm) deep-well socket.

1 Loosen Mounting Bolt on top side of machine while applying

counter-pressure to Adjusting Nut on underside of deck.

NOTE:NOTE:

NOTE: The mounting bolt muse be loosened first.

NOTE:NOTE:

2 Rotate Adjusting Nut counterclockwise with socket to apply

tension to belt.

3 While holding the tension on the Adjusting Nut. Tighten Mount-

ing Bolt.

4 Check belt tension by pinching belt together. Belt should only

depress 1/2" (12mm).

The following information refers to United States regulations on pro­pane. For outside the United States, owner, must assure that required
regulations are met.

The manufacturer would like to acknowledge NFPA 58, Standard for
Storage and Handling of Liquefied Petroleum Gases, 1993 Edition. This
publication is available through the National Fire Protection Associa­tion (NFPA) in Quincy, Massachusetts (1-800-344-3555). The NFPA was
established to set guidelines for, among other things, the use of pro­pane.

Propane is a flammable gas whose vapors are heavier than air. It can
explode under certain conditions. It is not different than other items
commonly used today which must be operated in a safe way such as
automobiles, gas stoves, airplanes, etc. Propane is odorized with an
agent with a distinct odor that is recognizable at very low concentra­tions. This helps in identifying leaks even when they are small.

Awareness and basic safely precautions are required. As long as these
precautions are followed, risk is negligible. Ignorance, however, could
pose needless risk. Therein lies the reason behind NFPA 58 and the
Safety Publication.

NFPA 58 categorizes propane-powered buffers with fork lift trucks, (see
section 3-6.4.4). In essence, the only difference between the two lies in
the ability of the buffer with its 20-pound tank to be stored in concealed
areas (like janitor closets, etc.).

If a machine and its tank of propane were stored in a closet and afire
occurred, the propane in the tank could be a threat to fire fighters due
to the potential for a B.L.E.V.E. (Boiling Liquid Expanding Vapor Explo­sion). Exposure of the tank to heat can also cause the relief valve to
open thereby releasing flammable vapors that can cause the fire to
intensify when ignited.

The NFPA Technical Committee prohibits the storage of such contain­ers in buildings.

8 8

8 - FORM NO. 56041536 - SelectGloss™ 21PH, 21PK, 27PK, 27PO, 27PR

8 8

REFUELING LP GAS TREFUELING LP GAS T

REFUELING LP GAS T

REFUELING LP GAS TREFUELING LP GAS T

NOTE:NOTE:

NOTE:

See

NOTE:NOTE:
Removal.

The LP gas tank supplied with machine has a 20Ib. (9.3kg), 5-gallon (18.9L)
capacity.
freeze up. Use only D.O.T. and U.L. Listed propane tank and only fill tank
at a reputable propane dealer .

‘INSTALLING OR CHANGING LPG FUEL TANK” for Tank

DO NOT OVERFILL. DO NOT OVERFILL.

DO NOT OVERFILL. Overfilling will cause the regulator to

DO NOT OVERFILL. DO NOT OVERFILL.

ANKSANKS

ANKS

ANKSANKS

CAUTION!CAUTION!

CAUTION!

CAUTION!CAUTION!

Avoid overfilling tanks. Only fill to 80% of capacity. The
manufacturer recommends that refueling be accomplished
by qualified personnel away from public buildings outside.
We further recommend that additional tanks be used so
that rather than refueling at the job site, a simple exchange
of tanks occurs.

DO NOT attempt to repair the propane tank yourself. Return tank to
dealer for repair.

NOTE:NOTE:

NOTE: Never use a tank not intended for the propane machine. Do not

NOTE:NOTE:
substitute tanks from barbecue grills, etc.

The manufacturer exclusively uses aluminum and steel cylinders that
meet the Department of Transportation guidelines contained in the
D.O.T. # 4ET240 and are additionally U.L. listed.

NFPA 58 discusses the major concerns for filling tanks properly in
Chapter 4. In summary, the tank should never be completely filled with
liquid. A tank that is completely full could create a hazard. The hazard is
known as a hydrostatic pressure situation.

To illustrate this situation, suppose the temperature outside is very cold
(perhaps well below freezing). You fill your tank outside and then bring
it inside where the temperature is maybe 60 degrees Fahrenheit or
warmer. An increase in air temperature will drive up the cylinder
pressure placing stress on the tank. Before reaching a critical pressure
point, the relief valve should open, relieving the pressure by venting
vapor at the top of the tank. However, if there is no vapor at the top of the
tank, this safety measure is compromised. Overfilled tanks do not allow
this built-in safety feature to function properly.

AA

TTENTION!TTENTION!

A

TTENTION!

AA

TTENTION!TTENTION!

Overfilling a tank usually results in liquid flowing through
the hose and down into the regulator. This can result in
damage to the machine.

If you observe frost on the regulator, someone has overfilled the tank.
Take the tank to a safe outside location and vent the excess propane.
Venting is accomplished by:

1 Removing the tank from machine.
2 Taking tank outside of building to safe area.
3 Opening the small relief valve located on top of machine.
4 Keep tank upright.
5 Allow to vent until fuel vapor is not visible.

Whether the tank is filled by weight (most accurate) or by volume, using
a gage, make sure the person doing the filling is qualified.

STORING LP GAS TSTORING LP GAS T

STORING LP GAS T

STORING LP GAS TSTORING LP GAS T

AA

TTENTION!TTENTION!

A

TTENTION!

AA

TTENTION!TTENTION!

Tanks (20Ib.) should not be stored in buildings used by the
public or frequented by anyone passing through or working
in the building. Inside storage in buildings designated as
shop or machinery facilities are acceptable.

Section 5-2.1.1 of the NFPA 58 says: “Containers in storage shall be so
located as to minimize exposure to excessive temperature rise, physi­cal damage or tampering.”

Provision must be made for venting the actual storage area with both
floor level and high level openings. This venting assures that the heavier
than air propane gas will not settle in pockets, but disperse.

If storage is in a shop or machine storage area that is connected or a
part of an office complex, it should be separated by afire wall along with
proper venting to the outside.

Since these requirements can seldom be found, outside open air
storage is the most practical alternative.

When this option is used, the storage container may be located with
“zero” clearance from the building and with at least 5' of space between
the cage and the nearest building opening.

The tank must be in a secure, tamper-proof security storage enclosure
that provides safety from accident or vandalism.

CAUTION!CAUTION!

CAUTION!

CAUTION!CAUTION!

Tanks must always be stored in the upright position. The
upright position assures that the discharge is largely vapor
rather than liquid. This is important from the standpoint of
both the quantity of the potential flammable vapor/air mix­ture and the relieving capacity for the pressure relief de­vice. (The escape of vapor presents much less hazard than
the escape of liquid).

ANKSANKS

ANKS

ANKSANKS

The manufacturer recommends that tanks be removed from the ma­chine after use and stored accordingly. The machine can then be
placed in a secure area inside, away from the tank.

NOTE: NOTE:

NOTE: Local jurisdiction always prevails there may. Be varying require-

NOTE: NOTE:

ments. Always check with the local authorities.

FORM NO. 56041536 - SelectGloss™ 21PH, 21PK, 27PK, 27PO, 27PR -

99

9

99

STORING MACHINESTORING MACHINE

STORING MACHINE

STORING MACHINESTORING MACHINE

1 Remove LPG tank from machine when not in use.

FOR SAFETY: Never release or bleed tank inside building or inFOR SAFETY: Never release or bleed tank inside building or in

FOR SAFETY: Never release or bleed tank inside building or in

FOR SAFETY: Never release or bleed tank inside building or inFOR SAFETY: Never release or bleed tank inside building or in
enclosed areas.enclosed areas.

enclosed areas.

enclosed areas.enclosed areas.

NOTE:NOTE:

NOTE: See “INSTALLING OR CHANGING LPG FUEL TANK” for Tank

NOTE:NOTE:
Removal.

2 Perform all Daily Maintenance procedures.

3 Change engine oil.

4 Store machine in cool, dry area, away from fuel tanks. Tilt

machine back onto rear caster (Park Position).

5 Store tanks in an approved area.

NOTE: NOTE:

NOTE: See “STORING LP GAS TANKS”.

NOTE: NOTE:

TRANSPORTING MACHINETRANSPORTING MACHINE

TRANSPORTING MACHINE

TRANSPORTING MACHINETRANSPORTING MACHINE

For ease of transportation, the machines handle can be folded over the
engine. The tank can be transported on machine provided that tank hold­down clamp is securely fastened around tank and tank valve is turned
completely OFF.

AA

TTENTION!TTENTION!

A

TTENTION!

AA

TTENTION!TTENTION!

Never transport a machine in an enclosed area that has not
had sufficient time to cool down.

10 10

10 - FORM NO. 56041536 - SelectGloss™ 21PH, 21PK, 27PK, 27PO, 27PR

10 10

TROUBLE SHOOTING GUIDETROUBLE SHOOTING GUIDE

TROUBLE SHOOTING GUIDE

TROUBLE SHOOTING GUIDETROUBLE SHOOTING GUIDE

PROBLEM PROBLEM

PROBLEM

PROBLEM PROBLEM
Will not start. No fuel or dirt in fuel line. See Engine Owners Manual for servicing.

Hard to start. Improper fuel, no fuel or dirt in fuel line. See Engine Owners Manual for servicing.

Lacks power . Improper valve clearance. See Engine Owners Manual for servicing.

Smell of burned rubber. Belt out of adjustment. See “ADJUSTING BELT TENSION”.
Engine overheats. Dirt in fuel line.

High fuel consumption. Dirty air filters. See Engine Owners Manual for servicing.

Machine stops suddenly. Faulty spark plug. See Engine Owners Manual for servicing.

Excess vibration. Bolts loose on engine or deck of unit. See Engine Owners Manual for servicing.

CAUSE CAUSE

CAUSE

CAUSE CAUSE

Blown head gasket.
Engine overload.
Dirty air cleaner.
Faulty spark plug.
Fuel system out of adjustment.
Defective ignition coil.

Engine overload.
Dirty air cleaner .
Faulty spark plug.
Spark plug or head bolts loose.
Blown head gasket.
Timing, coil, or valve needs adjusting.
Carburetor needs adjusting.
Regulator needs adjusting.
Insufficient vacuum.

Improper fuel or dirt in line.
Faulty spark plug.
Improper oil level.
Valve seats need adjusting.
Leaking head gasket.
Governor needs adjusting.
Worn rings.

Incorrect oil level.
Engine overload.

Dirty air cleaners.

Pad not centered on pad driver .
Incorrect pad size for pad driver.
Oil shut down sensor activated. Add recommended oil.

No fuel or dirt in fuel line.
Incorrect oil level.
Engine overload.
Dirty air filters.
Faulty spark plug.

SOLUTION SOLUTION

SOLUTION

SOLUTION SOLUTION

FORM NO. 56041536 - SelectGloss™ 21PH, 21PK, 27PK, 27PO, 27PR -

1111

11

1111

1212

12

1212

SELECTGLOSSSELECTGLOSS

SELECTGLOSS

SELECTGLOSSSELECTGLOSS

™™

™

SelectGlossSelectGloss

SelectGloss

SelectGlossSelectGloss

™™

™™

™

™™

21PH / 21PK 21PH / 21PK

21PH / 21PK

21PH / 21PK 21PH / 21PK

02-10

FORM NO. 56041536

02-10

04-5

SELECTGLOSSSELECTGLOSS

SELECTGLOSS

SELECTGLOSSSELECTGLOSS

™™

™

SelectGlossSelectGloss

SelectGloss

SelectGlossSelectGloss

™™

™™

™

™™

21PH / 21PK 21PH / 21PK

21PH / 21PK

21PH / 21PK 21PH / 21PK

1313

13

1313

ItemItem

Item

ItemItem

Ref. No.Ref. No.

Ref. No.

Ref. No.Ref. No.

1 56649812 2 Foam Hand Grip
2 56649816 1 FM Handle
3 56649726 1 Clutch Switch Mounting Plate

4 56102526 1 Key Switch
* 56102583 1 Replacement Key
5 56102527 1 Key Switch Holder
6 56649817 1 Battery Box
* 56649818 1 Key Switch Bracket

* 56649819 1 Choke Bracket (Kawasaki)
7 56102507 1 Kawasaki 17HP

56102532 1 Honda 390 13HP
8 56102508 1 Pulley, 3.5 x 1
9 56102523 1 Battery Connector Complete (Kawasaki)

10 56102522 1 Battery, 12V
11 56102521 1 Hour Meter
12 56649820 1 Deck, 21” Aluminum
13 56649821 1 Bumper Molding
14 56015141 2 Decal, Kent SelectGloss 21PH

56015144 2 Decal, Kent SelectGloss 21PK

15 56102509 1 Front Bearing Assy
16 56102533 1 Pulley, 6.2
17 56649822 1 Belt, B x 40
18 56102513 1 Centerlock

19 56649823 2 Wheel W/Bracket, 6 x 5

56649824 2 Wheel, 6 x 1.5

20 56102535 1 21” Flex Pad Driver
21 56102518 1 Caster, 3”
22 56102517 1 Flange

23 56102519 1 Idler Pulley
24 56102520 1 Tensioner Arm
25 56102524 1 Steel LP Tank
26 56649825 2 Velcro Tape
27 56102529 1 Throttle Cable

28 56102598 1 21” Flex Pad Driver Complete
** 56102618 1 21” Pad Driver Complete

QtyQty

Qty

QtyQty

DescriptionDescription

Description

DescriptionDescription

* 56102538 1 Choke Cable (Kawasaki)
* 56102539 1 Honda Starter

** 56388355 1 21” Beige Pads (case of 5)
** 56102615 1 Honda GXV390 Engine Service Kit
** 56102617 1 Kawasaki 17hp Engine Service Kit
** 56102658 A/R Two Tank Cage

* = Not Shown
** = Optional

NOTE:NOTE:

NOTE: For engine information not listed in the Standard Parts List, refer to the appropriate Engine Parts Manual.

NOTE:NOTE:

FORM NO. 56041536

1414

14

1414

SELECTGLOSSSELECTGLOSS

SELECTGLOSS

SELECTGLOSSSELECTGLOSS

™™

™

SelectGlossSelectGloss

SelectGloss

SelectGlossSelectGloss

™™

™™

™

™™

27PK / 27PO 27PK / 27PO

27PK / 27PO

27PK / 27PO 27PK / 27PO

02-10

FORM NO. 56041536

02-10

04-5

SELECTGLOSSSELECTGLOSS

SELECTGLOSS

SELECTGLOSSSELECTGLOSS

™™

™

SelectGlossSelectGloss

SelectGloss

SelectGlossSelectGloss

™™

™™

™

™™

27PK / 27PO 27PK / 27PO

27PK / 27PO

27PK / 27PO 27PK / 27PO

1515

15

1515

ItemItem

Item

ItemItem

Ref. No.Ref. No.

Ref. No.

Ref. No.Ref. No.

1 56649812 2 Foam Hand Grip
2 56649816 1 FM Handle
3 56649726 Clutch Switch Mounting Plate
4 56102526 1 Key Switch

* 56102583 1 Replacement Key
5 56102527 1 Key Switch Holder
6 56649817 1 Battery Box
* 56649818 1 Key Switch Bracket
* 56649819 1 Choke Bracket (Kawasaki)

7 56102507 1 Kawasaki 17HP

56102541 1 Onan 20HP
8 56102508 1 Pulley, 3.5 x 1
9 56102523 1 Battery Connector Complete (Kawasaki)

56102542 1 Battery Connector (Onan)

10 56102522 1 Battery, 12V
11 56102521 1 Hour Meter
12 56649826 1 Deck, 27” Aluminum
13 56649821 1 Bumper Molding
14 56015148 2 Decal, Kent SelectGloss 27PK

56015152 2 Decal, Kent SelectGloss 27PO

15 56102509 1 Front Bearing Assy
16 56102510 1 Pulley, 8.5 x 1
17 56102512 1 Belt, B x 50
18 56102513 1 Centerlock

19 56649823 2 Wheel W/Bracket, 6 x 5

56649824 2 Wheel, 6 x 1.5

20 56102514 1 27” Flex Pad Driver
21 56649827 1 Caster
22 56102517 1 Flange

23 56102519 1 Idler Pulley
24 56102520 1 Tensioner Arm
25 56102524 1 Steel LP Tank
26 56649825 2 Velcro Tape
27 56102529 1 Throttle Cable

28 56102516 1 27” Flex Pad Driver Complete
** 56102619 1 27” Pad Driver Complete

QtyQty

Qty

QtyQty

DescriptionDescription

Description

DescriptionDescription

* 56102538 1 Choke Cable (Kawasaki)
* 56102543 1 Regulator Bracket (Onan)

** 56420163 1 27” Beige Pads (case of 5)
** 56102616 1 Onan 20 P248 Engine Service Kit
** 56102617 1 Kawasaki 17hp Engine Service Kit
** 56102658 A/R Two Tank Cage

* = Not Shown
** = Optional

NOTE:NOTE:

NOTE: For engine information not listed in the Standard Parts List, refer to the appropriate Engine Parts Manual.

NOTE:NOTE:

FORM NO. 56041536

1616

16

1616

SELECTGLOSSSELECTGLOSS

SELECTGLOSS

SELECTGLOSSSELECTGLOSS

™™

™

SelectGlossSelectGloss

SelectGloss

SelectGlossSelectGloss

™™

FRONT

™™

™

™™

27PR 27PR

27PR

27PR 27PR

02-10

03-7

26

27

22

31

17

30

29

1

23

21

24

20

28

19

25

16

2

13

18

14

9

32

3

7

15

10

8

5

4

11

6

12

FORM NO. 56041536

02-10

04-5

SELECTGLOSSSELECTGLOSS

SELECTGLOSS

SELECTGLOSSSELECTGLOSS

™™

™

SelectGlossSelectGloss

SelectGloss

SelectGlossSelectGloss

™™

™™

™

™™

27PR 27PR

27PR

27PR 27PR

1717

17

1717

ItemItem

Item

ItemItem

Ref. No.Ref. No.

Ref. No.

Ref. No.Ref. No.

1 56102645 1 Robin ZXV 653 Engine
2 56649826 1 Deck 27” Aluminum
3 56102509 1 Front Bearing Assy Complete
4 56102648 1 Pulley, 7.0 x 1.0

5 56102508 1 Pulley, 3.5 x 1.0
6 56102649 1 Belt, B x 48
7 56102520 1 Belt Tensioner
8 56102519 1 Idler pulley
9 56102517 1 Flange

10 56102514 1 27” Flex Pad Driver
11 56102513 1 Center lock
12 56420163 A/R 27” Beige Pads (case of 5)
13 56649827 2 2” Caster W/Gray Wheel
14 56102651 2 Bracket Wheel 5”

15 56649824 2 Wheel, 6” x 1.5” W/Axle

* 56649823 2 Wheel W/Bracket

16 56102521 1 Hour Meter
17 56649816 1 FM Handle
18 56102528 1 Toggle

19 56102524 1 Tank, LP Steel W/OPD
20 56102529 1 Throttle Cable
21 56649812 2 Hand Grip
22 56649817 1 Battery Box
23 56102650 1 Battery Connector Complete

24 56102527 1 Key Switch Housing
25 56102526 1 Key Switch

* 56102583 1 Replacement Key

26 56102522 1 Battery, 12V
27 56102538 1 Choke Cable

28 56649818 1 Key Switch Bracket
29 56649819 1 Choke Bracket
30 56649726 1 Clutch Switch Mounting Plate
31 56102575 1 Clutch Switch Assy Complete
32 56015207 2 Decal, Kent SelectGloss 27

QtyQty

Qty

QtyQty

DescriptionDescription

Description

DescriptionDescription

(14 & 15)(14 & 15)

(14 & 15)

(14 & 15)(14 & 15)

** 56102646 1 Robin 22hp Engine Service Kit
** 56102658 A/R Two Tank Cage

* = Not Shown
** = Optional

NOTE:NOTE:

NOTE: For engine information not listed in the Standard Parts List, refer to the appropriate Engine Parts Manual.

NOTE:NOTE:

FORM NO. 56041536

1818

18

1818

ROBIN ZXV 653 ENGINEROBIN ZXV 653 ENGINE

ROBIN ZXV 653 ENGINE

ROBIN ZXV 653 ENGINEROBIN ZXV 653 ENGINE

™™

™

SelectGlossSelectGloss

SelectGloss

SelectGlossSelectGloss

™™

4

3

02-10

03-7

FRONT

5

8

2

7

9

1

13

15

6

12

FORM NO. 56041536

10

14

11

02-10

03-7

ROBIN ZXV 653 ENGINEROBIN ZXV 653 ENGINE

ROBIN ZXV 653 ENGINE

ROBIN ZXV 653 ENGINEROBIN ZXV 653 ENGINE

™™

™

SelectGlossSelectGloss

SelectGloss

SelectGlossSelectGloss

™™

1919

19

1919

ItemItem

Item

ItemItem

** = Optional

NOTE:NOTE:

NOTE: For engine information not listed in the Standard Parts List, refer to the appropriate Engine Parts Manual.

NOTE:NOTE:

Ref. No.Ref. No.

Ref. No.

Ref. No.Ref. No.

1 56102565 1 Recoil Filter Support gasket
2 56102632 1 Engine Cover
3 56102633 1 Filter Support Screen
4 56102634 1 Recoil Filter
5 56102563 1 Oil Pressure Switch
6 56102635 1 Oil Drain Valve
7 56102506 1 Automatic Shut Down system
8 56102637 2 Scr, Pan Phil 6-32 x .62
9 56102638 2 Nut, Jack 6-32

10 56102639 2 Exhaust Manifold Gasket
11 56102640 1 Exhaust Manifold
12 56102641 1 Muffler Clamp
13 56102642 1 Muffler, Catalytic
14 56102643 1 Oxygen Sensor
15 56102645 1 Robin ZXV 653 Engine
** 56102646 1 Robin 22hp Engine Service Kit

QtyQty

Qty

QtyQty

DescriptionDescription

Description

DescriptionDescription

FORM NO. 56041536

2020

20

2020

ROBIN ZXV 653 CARBURETION SYSTEMROBIN ZXV 653 CARBURETION SYSTEM

ROBIN ZXV 653 CARBURETION SYSTEM

ROBIN ZXV 653 CARBURETION SYSTEMROBIN ZXV 653 CARBURETION SYSTEM

™™

™

SelectGlossSelectGloss

SelectGloss

SelectGlossSelectGloss

™™

02-10

03-7

1

4

7

2

8

5

7

3

9

6

13

FORM NO. 56041536

10

11

12

02-10

03-7

ROBIN ZXV 653 CARBURETION SYSTEMROBIN ZXV 653 CARBURETION SYSTEM

ROBIN ZXV 653 CARBURETION SYSTEM

ROBIN ZXV 653 CARBURETION SYSTEMROBIN ZXV 653 CARBURETION SYSTEM

™™

™

SelectGlossSelectGloss

SelectGloss

SelectGlossSelectGloss

™™

2121

21

2121

ItemItem

Item

ItemItem

NOTE:NOTE:

NOTE: For engine information not listed in the Standard Parts List, refer to the appropriate Engine Parts Manual.

NOTE:NOTE:

Ref. No.Ref. No.

Ref. No.

Ref. No.Ref. No.

1 56102590 2 Stud, M6 x 130
2 56102622 2 Gasket, Insulator
3 56102623 1 Insulator
4 56102549 1 Vacuum Hose
5 56102586 1 Rubber Cap ¼
6 56102624 1 Carburetor Assy
7 56102625 2 Gasket, Cleaner
8 56102626 1 Spacer, Air Cleaner
9 56102627 1 Fuel Load Block

10 56102629 1 Orifice #26
11 56102630 1 90 Elbow 3/8NPT x 5/16 Hose Barb
12 56102550 1 Fuel Hose
13 56102631 2 Flange Nut

QtyQty

Qty

QtyQty

DescriptionDescription

Description

DescriptionDescription

FORM NO. 56041536

2222

22

2222

KAKA

WW

KA

KAKA

SelectGlossSelectGloss

SelectGloss

SelectGlossSelectGloss

ASAKI AUTOMAASAKI AUTOMA

W

ASAKI AUTOMA

WW

ASAKI AUTOMAASAKI AUTOMA

TIC SHUT DOWN SYSTEMTIC SHUT DOWN SYSTEM

TIC SHUT DOWN SYSTEM

TIC SHUT DOWN SYSTEMTIC SHUT DOWN SYSTEM

™™

™

™™

02-10

FORM NO. 56041536

02-10

KAKA

WW

KA

KAKA
SelectGlossSelectGloss

SelectGloss

SelectGlossSelectGloss

ASAKI AUTOMAASAKI AUTOMA

W

ASAKI AUTOMA

WW

ASAKI AUTOMAASAKI AUTOMA

TIC SHUT DOWN SYSTEMTIC SHUT DOWN SYSTEM

TIC SHUT DOWN SYSTEM

TIC SHUT DOWN SYSTEMTIC SHUT DOWN SYSTEM

™™

™

™™

2323

23

2323

ItemItem

Item

ItemItem

NOTE:NOTE:

NOTE: For engine information not listed in the Standard Parts List, refer to the appropriate Engine Parts Manual.

NOTE:NOTE:

Ref. No.Ref. No.

Ref. No.

Ref. No.Ref. No.

1 56102560 1 Muffler (cat)
2 56102570 1 Oxygen Sensor
3 56102568 1 Manifold
4 56102571 1 Auto Shutdown
5 56102561 1 Support
6 56102562 1 Air Filter (recoil)
7 56102507 1 Kawasaki 17HP
8 56102563 1 Oil Pressure Switch
9 56102572 1 Oil Drain Valve

10 56102564 1 Muffler Clamp
11 56102550 1 Fuel Hose
12 56102549 1 Vacuum Hose
13 56102565 1 Recoil Filter Support Gasket
14 56102569 1 Starter
15 56102566 1 Starter Solenoid
16 56102567 1 Muffler Bracket (21” Only)

QtyQty

Qty

QtyQty

DescriptionDescription

Description

DescriptionDescription

FORM NO. 56041536

2424

24

2424

HONDA FUEL SYSTEMHONDA FUEL SYSTEM

HONDA FUEL SYSTEM

HONDA FUEL SYSTEMHONDA FUEL SYSTEM

™™

™

SelectGlossSelectGloss

SelectGloss

SelectGlossSelectGloss

™™

02-10

ItemItem

Item

ItemItem

NOTE:NOTE:

NOTE: For engine information not listed in the Standard Parts List, refer to the appropriate Engine Parts Manual.

NOTE:NOTE:

Ref. No.Ref. No.

Ref. No.

Ref. No.Ref. No.

1 56102547 1 Quick Coupler
2 56102546 1 LP Hose
3 56102548 1 Fitting, 1/4 x 90 Street Elbow
4 56102549 3 Hose, Vacuum
5 56102550 1 Hose, Fuel
6 56102551 1 Fitting, 3/8 Barb x 3/8 MP
7 56102555 1 Regulator
8 56102556 1 Lockoff

9 56102554 2 Fitting, 1/4 Barb x 1/4 MP
10 56102557 1 Fitting, 3/8 Flare x 1/4 MP
11 56102558 1 Vac Tee
12 56102559 1 LP Hose

QtyQty

Qty

QtyQty

DescriptionDescription

Description

DescriptionDescription

FORM NO. 56041536

02-10

KAKA

WW

KA

KAKA
SelectGlossSelectGloss

SelectGloss

SelectGlossSelectGloss

ASAKI FUEL SYSTEMASAKI FUEL SYSTEM

W

ASAKI FUEL SYSTEM

WW

ASAKI FUEL SYSTEMASAKI FUEL SYSTEM

™™

™

™™

2525

25

2525

ItemItem

Item

ItemItem

NOTE:NOTE:

NOTE: For engine information not listed in the Standard Parts List, refer to the appropriate Engine Parts Manual.

NOTE:NOTE:

Ref. No.Ref. No.

Ref. No.

Ref. No.Ref. No.

1 56102547 1 Quick Coupler
2 56102546 1 LP Hose
3 56102548 1 Fitting, 1/4 x 90 Street Elbow
4 56102549 1 Hose, Vacuum
5 56102550 1 Hose, Fuel
6 56102551 1 Fitting, 3/8 Barb x 3/8 MP
7 56102552 1 Regulator
8 56102553 1 Fuel Lock W/Filter 12V
9 56102554 1 Fitting, 1/4 Barb x 1/4 MP

QtyQty

Qty

QtyQty

DescriptionDescription

Description

DescriptionDescription

FORM NO. 56041536

2626

26

2626

ROBIN FUEL SYSTEMROBIN FUEL SYSTEM

ROBIN FUEL SYSTEM

ROBIN FUEL SYSTEMROBIN FUEL SYSTEM

™™

™

SelectGlossSelectGloss

SelectGloss

SelectGlossSelectGloss

™™

4

02-10

03-7

1

2

ItemItem

Item

ItemItem

Ref. No.Ref. No.

Ref. No.

Ref. No.Ref. No.

1 56102552 1 Regulator
2 56102554 1 Fitting, 1/4 Barb x 1/4MP
3 56102551 1 Fitting, 3/8 Barb x 3/8MP
4 56102553 1 Fuel Lock W/Filter 12V
5 56102621 1 LP Hose 28”, 1/4 x 1/4NPT
6 56102547 1 Quick Coupling

QtyQty

Qty

QtyQty

DescriptionDescription

Description

DescriptionDescription

3

6

5

NOTE:NOTE:

NOTE: For engine information not listed in the Standard Parts List, refer to the appropriate Engine Parts Manual.

NOTE:NOTE:

FORM NO. 56041536

02-10

ELECTRIC CLUTCH ASSEMBLELECTRIC CLUTCH ASSEMBL

ELECTRIC CLUTCH ASSEMBL

ELECTRIC CLUTCH ASSEMBLELECTRIC CLUTCH ASSEMBL

™™

™

SelectGlossSelectGloss

SelectGloss

SelectGlossSelectGloss

™™

YY

Y

YY

2727

27

2727

ItemItem

Item

ItemItem

NOTE:NOTE:

NOTE: For engine information not listed in the Standard Parts List, refer to the appropriate Engine Parts Manual.

NOTE:NOTE:

Ref. No.Ref. No.

Ref. No.

Ref. No.Ref. No.

1 56102573 1 Arm & Springs (2 each)
2 56102574 1 Switch (clutch)
3 56102575 1 Clutch Switch Assy Complete
4 56102576 1 Spacer
5 56102577 1 Electric Clutch
6 56102578 1 Clutch Arm

QtyQty

Qty

QtyQty

DescriptionDescription

Description

DescriptionDescription

FORM NO. 56041536

2828

28

2828

KILL SWITCH ASSEMBLKILL SWITCH ASSEMBL

KILL SWITCH ASSEMBL

KILL SWITCH ASSEMBLKILL SWITCH ASSEMBL

™™

™

SelectGlossSelectGloss

SelectGloss

SelectGlossSelectGloss

™™

YY

Y

YY

02-10

ItemItem

Item

ItemItem

NOTE:NOTE:

NOTE: For engine information not listed in the Standard Parts List, refer to the appropriate Engine Parts Manual.

NOTE:NOTE:

Ref. No.Ref. No.

Ref. No.

Ref. No.Ref. No.

1 56102573 1 Arm & Springs (2 each)
2 56102579 1 Switch (kill)
3 56102580 1 Kill Switch Assy Complete

QtyQty

Qty

QtyQty

DescriptionDescription

Description

DescriptionDescription

FORM NO. 56041536

02-10

KAKA

WW

KA

KAKA

SelectGlossSelectGloss

SelectGloss

SelectGlossSelectGloss

ASAKI FUEL LOAD BLOCKASAKI FUEL LOAD BLOCK

W

ASAKI FUEL LOAD BLOCK

WW

ASAKI FUEL LOAD BLOCKASAKI FUEL LOAD BLOCK

™™

™

™™

2929

29

2929

ItemItem

Item

ItemItem

NOTE:NOTE:

NOTE: For engine information not listed in the Standard Parts List, refer to the appropriate Engine Parts Manual.

NOTE:NOTE:

Ref. No.Ref. No.

Ref. No.

Ref. No.Ref. No.

1 56102584 1 Carburetor Assy
2 56102585 1 Fuel Load Block
3 56102586 1 Rubber Cap 1/4
4 56102587 1 Insulator
5 56102588 1 Vacuum Tube
6 56102589 2 Gasket Air Filter
7 56102590 2 Stud, M6 x 130
8 56102591 1 Brass Plug
9 56102592 1 Elbow, 3/8 x 1/4 MP

10 56102593 2 Gasket Air Filter

QtyQty

Qty

QtyQty

DescriptionDescription

Description

DescriptionDescription

FORM NO. 56041536

3030

30

3030

KAKA

WW

KA

KAKA

SelectGlossSelectGloss

SelectGloss

SelectGlossSelectGloss

ASAKI SCHEMAASAKI SCHEMA

W

ASAKI SCHEMA

WW

ASAKI SCHEMAASAKI SCHEMA

TIC & HARNESSTIC & HARNESS

TIC & HARNESS

TIC & HARNESSTIC & HARNESS

™™

™

™™

FUEL LOAD BLOCKFUEL LOAD BLOCK

FUEL LOAD BLOCK

FUEL LOAD BLOCKFUEL LOAD BLOCK

02-10

FORM NO. 56041536