Kb Electronics KBCC-SERIES User Manual.pdf

KBPB & KBCC-R SUPPLEMENTAL INFORMATION

DESCRIPTION

The Anti-Plug Reversing Module used in the KBPB and KBCC-R models has been changed from APRM-2C to APRM-3. The General Performance Specifications of these products have not changed. This supplement is being supplied with the KBPB and KBCC-R Installation and Operation Manuals (Part Nos. A40210A and A40225A) until the new manuals are available.

The figures below replace the figures in the KBPB and KBCC-R Installation and Operation Manuals. For further assistance, contact our Sales Department toll free, at 800-221-6570Φ.

Read Safety Warning

SAFETY WARNING!

This drive contains electronic Start/Stop circuits which can be used to start and stop the drive. However, these circuits are never to be used as safety disconnects since they are not failsafe. Use only the AC line for this purpose. Be sure to follow all instructions carefully. Fire and/or electrocution can result due to improper use of this product.

Power

Main Speed Potentiometer

Forward-Brake-Reverse Switch

A2

TB1

TB1

A1

+

-

S3 S4

S3 S4

FWD-BRK-REV SWITCH

ARMATURE

REV

L2

S2

S2

AC LINE INPUT

BRK

P2 P3 S1

P2 P3 S1

FWD

L1

HIGH

TB3

WIPER

LOW

P1

P1

MAIN SPEED

CHASSIS

GROUND

POTENTIOMETER

(EARTH)

Run-Brake and Forward-Reverse Switches

Forward-Brake-Reverse Switch with

Forward-Brake-Reverse and Run-Brake-Jog

Adjustable Forward and Preset Reverse Speed

Switches with Main Speed Potentiometer

TB1

TB1

S4

TB1

S4

S4

FWD-BRK-REV SWITCH

FWD-REV SWITCH

P1 P2 P3 S1 S2 S3

P1 P2 P3 S1 S2 S3

P2 P3 S1 S2 S3

REV

REV

BRK

FWD

BRK

REV

RUN-BRAKE SWITCH

FWD

JOG

FWD

HIGH

HIGH

BRK

FWD-BRK-REV SWITCH

RUN

WIPER

WIPER

RUN-BRK-JOG SWITCH

LOW

LOW

MAIN SPEED

P1

MAIN SPEED

POTENTIOMETER

POTENTIOMETER

Forward-Brake-Reverse and Run-Brake-Jog

Tach-Generator Feedback Connections

Switches with Main Speed Potentiometer

and Remote Jog Potentiometer

50 Volts per 1000 RPM Tach-Generator

7 Volts per 1000 RPM Tach-Generator

TB1

FWD-BRK-REV SWITCH

S4

REV

S3

RUN-BRK-JOG SWITCH

BRK

S2

"B" TERMINAL

"T" TERMINAL

FWD

S1

RUN

BRK

JOG

(ON KBMM)

(ON KBMM)

P3

HIGH

WIPER

P1 P2

TB2

LOW

TB2

-

+

-

+

TACH-GENERATOR

TACH-GENERATOR

MAIN SPEED

FF+-

FF+-

POTENTIOMETER

REMOTE JOG

POTENTIOMETER

KB ELECTRONICS, INC.

12095 NW 39th Street, Coral Springs, FL 33065-2516 • [phone] • FAX [phone]

Outside Florida Call Toll Free [phone] • [e-mail]	(A40150) – Rev. C – 7/2006
www.kbelectronics.com	Print Code

KBPB & KBCC-R SUPPLEMENTAL INFORMATION

				The latest versions (11/2000) of the KBPB and KBCC-R controls do not contain
				Inhibit terminals on the terminal block. The Inhibit feature is available, however,
				by wiring a switch or contact to the I1 and I2 QD terminals on the PC board.
				The control uses the S2 terminal for brake-to-stop operation (open to stop,
				close to run). If the application requires coast-to-stop operation, connect the
				Inhibit Switch as shown below.
	I2	P1	P3	One side of the Inhibit Switch connects to the new piggyback I1 QD Terminal.
				The other side of the Inhibit Switch connects to the I2 QD Terminal (or the F-
			P2	terminal on Terminal Block TB2). It is recommended that the Inhibit Switch wires
		I1		be routed (and secured with wire ties) with other signal wires (S1, S2, S3, etc.).
		T
A-
		B		Do not route the Inhibit	Inhibit Switch
		F+		wires with AC line or	(Close to Coast-to-Stop)
			L1	motor wires unless	(Open to Run)
	A+			shielded cables are used.
F-		L2
				MOUNTING INSTRUCTION FOR CHASSIS & IP-20 CONTROLS

	Note: KBPB shown. The KBCC-R uses the same PC board.	WARNING! This control must be mounted in an enclosure. Care
		should be taken to avoid extreme hazardous locations where
		physical damage to the control can occur due to moisture, metal chips, dust,
	SAFETY WARNING!	and other contamination including corrosive atmosphere. If such contamination
	This drive contains electronic Start/Stop circuits which can be used to	is present, special enclosures may be required such as NEMA type 4X. Failure
		to observe these instructions could cause an electrical shock, fire, or explosion
	start and stop the drive. However, these circuits are never to be used
		in this product or the products used with this product. Do not use this control
	as safety disconnects since they are not fail-safe. Use only the AC
		in an explosion-proof application. You must read the Safety Warning which
	line for this purpose. Be sure to follow all instructions carefully. Fire
		accompanies this product.
	and/or electrocution can result due to improper use of this product.

KB ELECTRONICS, INC.

12095 NW 39th Street, Coral Springs, FL 33065-2516 • [phone] • FAX [phone]
Outside Florida Call Toll Free [phone] • [e-mail]	(A40150) – Rev. C – 7/2006
www.kbelectronics.com	Print Code