LT-32AX5
LT-26AX5
ENGLISH
WIDE LCD PANEL TV
INSTRUCTIONS
LCT1926-001A-H
Thank you for buying this JVC LCD flat television.
To make sure you understand how to use your new TV, please read this manual thoroughly before you
begin. (“LCD” stands for Liquid Crystal Display.)
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
WARNING
• Fingers may be trapped under the TV causing injuries. Hold the TV at the
bottom in the middle, and do not allow it to tilt up or down.
WARNING
• The TV may fall causing injuries. Hold the bottom of the stand with your
hand and tilt the TV up and down.
• Do not allow children to hang from the TV, place their elbows on the TV
or lean against the TV. Doing so may cause the TV to fall over and lead to
injuries.
CAUTION
• The TV screen may be damaged if the TV is carried as shown in the
diagram below.
The TV should always be carried by two people.
ENGLISH
CAUTION:
• Operate only from the power source specified (AC 110 – 240 V, 50/60 Hz) on the unit.
• Avoid damaging the AC plug and power cord.
• When you are not using this unit for a long period of time, it is recommended that you disconnect
the power cord from the main outlet.
DO NOT block the TV’s ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be
able to get out.)
DO NOT place anything on top of the TV.
(such as cosmetics or medicines, flower vases, potted plants, cups, etc.)
DO NOT allow objects or liquid into the cabinet openings.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
DO NOT place any naked flame sources, such as lighted candles, on the TV.
DO NOT subject the TV to direct sunlight.
If there is a fault, unplug the unit and call a service technician. Do not attempt to repair it yourself
or remove the rear cover.
1
Distance recommendations
Avoid improper installation and never position the unit
where good ventilation is impossible.
When installing this TV, distance recommendations
150 mm 150 mm
200 mm 200 mm
must be maintained between the set and the wall, as well
as inside a tightly enclosed area or piece of furniture.
Keep to the minimum distance guidelines shown for
safe operation.
ENGLISH
Pixel defects
LCDs use collections of fine points (“pixels”) to display images. While there is no problem with
more than 99.99% of these pixels, please understand that a very small number of pixels may not
light, or may light all the time.
The surface of the TV screen is easily damaged. Be very careful with it when handling the TV.
Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully.
Never use any cleaner or detergent on it.
Cleaning the screen
The screen is coated with a special thin film to reduce reflection. If this film is damaged, uneven
colours, discolouration, scratches, and other problems that cannot be repaired may occur. Pay
attention to the following when handling the screen.
• Do not use glue or adhesive tape on the screen.
• Do not write on the screen.
• Do not allow the screen to come in contact with any hard objects.
• Do not allow condensation to form on the screen.
• Do not use alcohol, thinner, benzene or other solvents on the screen.
• Do not rub the screen hard.
50 mm
2
CONTENTS
Setting up your TV ...................................4
Installation.................................................. 4
Connecting other devices .......................... 4
Cable holder............................................... 7
Connecting the power cord to the AC
outlet....................................................... 8
Putting the batteries into the remote
control..................................................... 8
Initial settings ............................................. 8
TV buttons and functions......................10
Turn the TV on from standby mode ......... 10
Choose a TV channel .............................. 10
Watch images from external devices....... 10
Adjust the volume .................................... 11
Using the Menu........................................ 11
Connecting headphones.......................... 11
Using the stand ........................................ 11
Remote control buttons and
functions..............................................12
Turn the TV on or off from standby mode
Choose a TV channel and watch images
from external devices ........................... 13
Adjust the volume .................................... 14
Information function ................................. 14
ZOOM function......................................... 15
3D SOUND function ................................. 16
Return to TV channel instantly................. 16
Favourite channel function....................... 17
Operating a JVC brand VCR or DVD
player.................................................... 18
.. 12
Teletext function ....................................19
Basic operation ........................................ 19
Using the List Mode ................................. 19
Hold.......................................................... 20
Sub-page ................................................. 20
Reveal...................................................... 20
Size .......................................................... 20
Index ........................................................ 21
Cancel...................................................... 21
Using the TV’s menu..............................22
Basic operation ........................................ 22
PICTURE menu ......................................23
PICTURE MODE...................................... 23
BACK LIGHT............................................ 23
CONTRAST ............................................. 23
BRIGHT.................................................... 23
SHARP..................................................... 23
COLOUR.................................................. 23
TINT ......................................................... 23
WHITE BALANCE.................................... 23
FEATURES .............................................. 24
SOUND menu ......................................... 25
STEREO / I • II ......................................... 25
BASS........................................................ 25
TREBLE ................................................... 25
BALANCE ................................................ 25
3D SOUND............................................... 25
FEATURES menu................................... 26
SLEEP TIMER ......................................... 26
CHANNEL GUARD .................................. 26
APPEARANCE......................................... 28
BLUE BACK ............................................. 28
FAVOURITE SETTING ............................ 28
SET UP menu ......................................... 29
AUTO PROGRAM.................................... 29
EDIT/MANUAL ......................................... 29
LANGUAGE ............................................. 33
VIDEO-3 SETTING .................................. 33
TELETEXT LANGUAGE .......................... 33
Displaying a computer screen.............. 34
Connecting to the computer ..................... 34
Watching images from a computer ..........34
Table of signals for each type of
computer............................................... 34
CH/CC numbers ..................................... 35
Troubleshooting ....................................36
Specifications ........................................38
ENGLISH
3
Setting up your TV
• When you install the TV on the wall, only use a JVC wall mounting unit (optional) which is
designed for this TV.
• Make sure that the TV is installed on the wall by a skilled installer.
Installation
Cautions for installation
ENGLISH
• Install the TV in a corner on a wall or on the floor so as to keep cords out of the way.
• The TV will generate a slight amount of heat during operation. Ensure that sufficient space is
available around the TV to allow satisfactory cooling. See “Distance recommendations” on
page 2.
Connecting other devices
Connect the equipment to the TV, making the correct rear panel and front panel connections.
Before connecting anything
• Read the manuals that came with the equipment. Depending on the equipment, the connection
method may be different from the diagram. Also, the equipment settings may need to change
depending on the connection method.
• Turn off all the equipment including the TV.
• The “Specifications” on page 38 give the details of the VIDEO terminals.
without terminal covers
Removing the terminal cover
[VIDEO-4]
Component video input
[VIDEO-3]
S-VIDEO input
Video input
Audio L/R input
[VIDEO-2]
Video input
Audio L/R input
Monitor output*
[VIDEO-1]
Video input
Audio L/R input
Monitor output*
Aerial inputPC input
* Monitor output: Output the images and sounds you are viewing.
4
Connecting the aerial
• The connecting cables are not provided.
If you are not connecting a VCR/DVD recorder.
75-ohm
Coaxial
Cable
Setting up your TV
Aerial
ENGLISH
If you are connecting a VCR/DVD, follow
VCR/DVD recorder
A → B in the diagram below.
Aerial
75-ohm
Coaxial
Cable
75-ohm
Coaxial
Cable
To Aerial
Output
To Aerial
Input
5
Setting up your TV
Connecting to the VIDEO-1/VIDEO-2 terminal (video input/monitor output)
To play the VCR/DVD player:
Connect the TV to the VCR/DVD player with the supplied SCART to RCA cable (for input/output).
Monitor output from the VIDEO-1/VIDEO-2 terminal
The video/sound signal you are viewing is always output from the VIDEO-1/VIDEO-2 terminal.
• Changing over a programme number (PR) also changes over the monitor output from the
ENGLISH
VIDEO-1/VIDEO-2 terminal.
• The PC signal cannot be output.
• Teletext programmes cannot be output.
To OUTPUT
VIDEO IN
AUDIO IN-L
AUDIO IN-R
SCART to RCA Cable
(for input/output)
VCR/DVD recorder
Outputs the images and sounds you are viewing.
To INPUT
VIDEO OUT
AUDIO OUT-L
AUDIO OUT-R
Connecting to the VIDEO-3 terminal (S-VIDEO or video input)
To play the VCR/DVD player:
Connect the TV to the VIDEO-3 terminal of the VCR/DVD player.
• You can choose between an S-VIDEO signal (Y/C signal) and a normal video signal
(composite signal). For details of how to operate the equipment, see “VIDEO-3 SETTING” on
page 33.
• You can also connect game consoles and camcorder.
To OUTPUT
VCR/DVD player
To OUTPUT
S-VIDEO IN
VIDEO IN
AUDIO IN-L
AUDIO IN-R
Game consoles/Camcoder
6
Setting up your TV
Connecting to the VIDEO-4 terminal (component video input)
To play the DVD player:
Connect the TV to the VIDEO-4 terminal of the DVD player.
• Audio is shared between the VIDEO-3 and VIDEO-4 terminal.
ENGLISH
COMPONENT IN
AUDIO IN-L
AUDIO IN-R
To OUTPUT
Connecting the PC
For details, see “Connecting to the computer” on page 34.
Cable holder
A cable holder which is used to keep the
connection cables tidy is attached to the back
of the stand. Gently squeeze the left and right
of the cable holder and pull it to remove it from
the stand. After putting the cables in the cable
holder, attach it to the back of the stand again.
cable holder
DVD player
7
Setting up your TV
s
Connecting the power cord to the AC outlet
Insert the AC plug on the power cord from
the TV into AC outlet.
Caution
ENGLISH
• Operate only from the power source
specified (AC 110 – 240 V, 50/60 Hz)
on the unit.
• Remove the AC plug from the outlet to
completely disconnect the TV from the
power supply.
Putting the batteries into the remote control
Use two AA/R6 dry cell batteries.
Insert the batteries from the - end, making
sure the + and - polarities are correct.
• The batteries we supply are only for
setting up and testing your TV, please
replace them as soon as you need to.
Initial settings
When the TV is first turned on, it goes into
the initial settings mode, and you will see the
JVC logo. Follow the instructions on the
screen display to make the initial settings.
# button
VCR/TV/DVD
switch
Yellow button
Blue button
7 button
1 Make sure to set the VCR/TV/DVD
switch on the remote control to the
TV position
• You cannot turn the TV on when the
VCR/TV/DVD switch is set to the
DVD position.
2 Press the # button on the remote
control
The TV turns on from standby mode and
the JVC logo is displayed.
• Check that the AC plug on the power
cord from the TV is connected to AC
outlet.
Remote control
sensor
8
Power lamp
Setting up your TV
• If the JVC logo does not appear this is
because your TV has already been
turned on for the first time:
use the “LANGUAGE”, “TELETEXT
LANGUAGE” and “AUTO
PROGRAM” functions to make the
initial settings. For details, see “SET
UP menu” on page 29.
3 Press the a button
The LANGUAGE menu appears.
4 Press the 6 buttons to choose
ENGLISH. Then press the a
button
The TELETEXT LANGUAGE menu
appears. Set the teletext language group
that corresponds to the language of the
teletext programme that you want to watch.
For details, see “TELETEXT
LANGUAGE” on page 33.
> TELETEXT LANGUAGE
GROUP-1
GROUP-2
GROUP-3
GROUP-4
OK
D1003
-EN
5 Press the 6 buttons to choose a
group. Then press the a button
The AUTO PROGRAM function starts.
The TV channels you receive are
automatically stored in the programme
numbers (PR) list.
>>
AUTO PROGRAM
CH
28
14%
D0004
-EN
• To stop the AUTO PROGRAM
function, press the b button.
6 After the TV channels have been
registered in the programme
numbers (PR), the EDIT menu
appears
EDIT
>
D0038
-EN
PR ID
AV
01
02
03
04
05
06
07
OK
MOVE
CH/CC
CH
CH
CH
CH
CH
CH
CC 01
ID
INSERT
21
22
23
24
25
26
MANUAL
DELETE
• You can proceed to edit the
programme numbers (PR) list using
the EDIT/MANUAL function. For
details, see “EDIT/MANUAL” on
page 29.
• If a TV channel you want to view is
not stored in the programme numbers
(PR) list, you can register it using the
MANUAL function. For details, see
“EDIT/MANUAL” on page 29.
• The AUTO PROGRAM function does
not store a TV channel to the
programme number PR 0 (AV).
• If you do not need to use the EDIT/
MANUAL function, press the a
button to close the EDIT menu.
Now, setting up is complete. Please
enjoy your new JVC TV!
ENGLISH
9
TV buttons and functions
ENGLISH
Turn the TV on from standby mode
Press the A button or the P p
buttons to turn the TV on from
standby mode.
When the TV is turned on, the power lamp
lights blue.
To turn the TV off:
Press the A button again.
The power lamp goes off.
Caution
•The A button on the TV does not fully
isolate the TV from the AC supply. If
you are not going to use the TV for a
long period, be sure to disconnect the
AC plug from the AC socket.
Choose a TV channel
Press the P p buttons to choose a
programme number (PR)
Watch images from external devices
Refer to the pages in parentheses for details.
1 Remote control sensor
2 Power lamp (page 8)
3 TV/AV button (page 10)
4 MENU/OK button (pages 11, 22)
5 P p buttons (page 10)
6 r (Volume) q buttons (page 11)
7 A (Stand by) button (page 10)
8 Headphone jack (mini jack) (page 11)
10
Press the TV/AV button to choose a
VIDEO terminal
TV mode VIDEO modes
Last
Programme
number
or
•The p p buttons can also be used to
choose a VIDEO terminal.
TV buttons and functions
Adjust the volume
Press the r (Volume) q buttons
The volume level indicator appears.
Using the Menu
Use the MENU/OK button
Refer to “Using the TV’s menu” (see
page 22) for details of using the menu.
Connecting headphones
Connect the headphones with a stereo minijack (3.5 mm diameter) to the headphone
jack at the TV front panel.
• No sound comes from the TV speakers
when the headphones are connected.
Using the stand
This stand can be used to adjust the direction
of the TV screen 5° up, 10° down, and 20° to
the left or right.
Tilt the TV up and down:
Rotate the TV to the left and right:
ENGLISH
11
Remote control buttons and functions
1 Muting button
2 Number buttons
3 Information button
4 c button
5 / (3D SOUND) button
6 b button
7 7 buttons
8 g (Text) button
9 p p buttons
0 VCR/DVD/Teletext control buttons
- p buttons
= d (Favourite) button
~ # (Standby) button
! VCR/TV/DVD switch
@ G button
# Colour buttons
$ H button
% a button
^ b button
& r (Volume) q buttons
Turn the TV on or off from standby mode
ENGLISH
1
2
3
4
5
6
7
8
~
!
@
#
$
%
^
12
9
0
=
&
Press the # (standby) button to turn
the TV on or off
When the TV is turned on, the power lamp
lights blue.
• The power can be turned on by pressing
the b button, p p buttons or Number
buttons.
To turn the TV on or off, set the VCR/TV/
DVD switch on the remote control to the
TV position and press the # button.
If the VCR/TV/DVD switch on the remote
control is set to the DVD position, the TV
will not be turned on or off even if the #
button is pressed.
Remote control buttons and functions
Choose a TV channel and watch images from external devices
Use the number buttons:
Enter the programme number (PR)
of the channel using the number
buttons.
Example:
•PR 6 → press 6
• PR 12 → press 1 and 2
Use the p p buttons:
Press the p p buttons to
choose the programme number
(PR) you want or an VIDEO
terminal.
Use the G button:
Press the G button to choose an
VIDEO terminal.
TV mode VIDEO modes
Programme
numbers
PR 1 – PR 99
• Since this TV is designed to make full use
of the resolution of the original video
source, the motion may appear unnatural
when the video source is input with
progressive-scanning component signals.
If this happens, change the output setting
of the connected device to interlacescanning component signal output. See
the instructions that came with the device
for more information.
• The PC sound is the same as the VIDEO-3
sound.
To return to a TV channel:
Press the b button, the p p buttons or
the number buttons.
To use the programme number PR 0
(AV):
When the TV and VCR/DVD recorder are
connected only by the aerial cable, choosing
the programme number PR 0 (AV) allows
you to view images from the VCR/DVD
recorder. Set the VCR/DVD recorder RF
channel to the programme number PR 0
(AV) manually. For details, see “EDIT/
MANUAL” on page 29.
Pressing the G button changes the choice as
follows:
TV mode VIDEO modes
ENGLISH
or
• You can choose a video input signal from
the S-VIDEO signal (Y/C signal) and
regular video signal (composite signal).
For details, see “VIDEO-3 SETTING” on
page 33.
• If you do not have a clear picture or no
colour appears, follow the operation
procedure “COLOUR SYSTEM” on
page 24.
• If you choose a VIDEO terminal with no
input signal, the VIDEO terminal number
becomes fixed on the screen.
Programme
numbers
PR 1 – PR 99
PR 0
or
• The VCR/DVD recorder sends its
playback image along the aerial cable as
an RF (radio frequency) signal.
• Also see your VCR/DVD recorder
instruction manual.
13
Remote control buttons and functions
Adjust the volume
Press the r q buttons to adjust
the volume.
The volume level indicator appears and the
volume changes as you press the r q
buttons.
ENGLISH
Muting the sound
Press the l (muting) button to
turn off the sound.
Pressing the l (muting) button again
restores the previous volume level.
Information function
You can see the channel number of the
programme you are watching or the PR
LIST.
From the PR LIST, you can choose a channel
or VIDEO terminal.
Press the h (Information) button to
display the information you want to
see.
Pressing the h (Information) button changes
the display as follows:
PR LIST
PR ID
AV
01
02
03
04
05
06
07
OK
-8
D0011
+8
-EN
Channel number display:
The channel number and channel name
(when the channel name is registered) of the
programme you are watching or the VIDEO
terminal number is displayed.
Channel number display
No indication
PR LIST:
The programme number (PR) and VIDEO
terminal list is displayed.
Pressing the a button after choosing the
programme number (PR) or VIDEO terminal
with the 7 buttons will display the
chosen programme or VIDEO terminal.
• For programme numbers (PR) for which
the CHANNEL GUARD function is set,
the n (CHANNEL GUARD) mark is
displayed. For details see “CHANNEL
GUARD” on page 26.
• For programme numbers (PR) which is
registered as a favourite channel, the d
(favourite) mark is displayed. For details
see “Favourite channel function” on
page 17.
14
Remote control buttons and functions
ZOOM function
You can change the screen size according to
the picture aspect ratio. Choose the optimum
one from the following ZOOM modes.
• The ZOOM mode is fixed at FULL when
you are using the TV as a PC screen.
REGULAR:
Use to view a normal picture (4:3 aspect
ratio) as this is its original shape.
PANORAMIC:
This stretches the left and right sides of a
normal picture (4:3 aspect ratio) to fill the
screen, without making the picture appear
unnatural.
• The top and bottom of the picture are
slightly cut off.
14:9 ZOOM:
This zooms up the wide picture (14:9 aspect
ratio) to the upper and lower limits of the
screen.
16:9 ZOOM:
This zooms up the wide picture (16:9 aspect
ratio) to the full screen.
FULL:
This uniformly stretches the left and right
sides of a normal picture (4:3 aspect ratio) to
fill the wide TV screen.
• For 16:9 aspect ratio pictures that have
been squeezed into a normal picture (4:3
aspect ratio), use the FULL mode to
restore the picture to its original shape.
Choose the ZOOM mode
1 Press the c button to display
the ZOOM menu
ZOOM
REGULAR
PANORAMIC
14:9 ZOOM
16:9 ZOOM
16:9 ZOOM SUBTITLE
FULL
OK
D0009
-EN
2 Press the 6 buttons to choose a
ZOOM mode. Then press the a
button
The picture expands and the chosen
ZOOM mode is displayed in about 5
seconds.
ENGLISH
16:9 ZOOM SUBTITLE:
This zooms up the wide picture (16:9 aspect
ratio) with subtitles to the full screen.
15
Remote control buttons and functions
Adjusting the visible area of the
picture
If subtitles or the top (or bottom) of the
picture are cut off, you can adjust the visible
area of the picture manually.
1 Press the c button
ENGLISH
The ZOOM menu appears.
2 Press the a button to display the
ZOOM mode indicator
The indicator appears.
16 : 9 ZOOM
D0010-EN
3 While it is displayed, press the 6
buttons to change the position of
the picture
• You cannot adjust the visible area in
REGULAR or FULL mode.
The visible area adjustment is saved even
after the TV channel is changed.
However, it is cancelled if the following
operations are performed.
• The power is turned off/on
• g (Text) button is pressed
• The TV is switched between TV mode
and VIDEO mode
MONO:
Select the MONO mode, when you listen to
the mono sound.
You can enjoy the sound for a wider
audience similar to stereo sound.
OFF:
The 3D SOUND function switches off.
• You can choose the 3D SOUND mode
with the “SOUND menu” (see page 25).
Return to TV channel instantly
You can return to a TV channel instantly.
Press the b button
The TV returns to the TV mode and a TV
channel appears.
3D SOUND function
You can enjoy sounds with a wider
ambience.
• This function does not work for the sound
from headphones.
Press the 3 button to select one of
3D SOUND modes
ON:
When you listen to stereo sound, please
select ON mode.
You can enjoy sound similar to the
experience at the theatre.
16
Remote control buttons and functions
Favourite channel function
You can register your favourite TV channels
(PR 1 – PR 99) in the number buttons 1 to 4.
After registering, the channel can be called
by pressing the d (favourite) button and a
number button 1 to 4.
Favourite channel registration
1 In the normal screen, choose a TV
channel (PR 1 – PR 99) that you
want to register
For details, refer to “Choose a TV channel
and watch images from external devices”
on page 13.
2 Press and hold the d (favourite)
button for three seconds or more
Then “SET 1-4?” appears on the screen.
3 Press one of the number buttons 1
to 4
The current channel is registered in the
pressed number button.
After “PROGRAMMED!” appears on the
screen, the favourite channel icon appears
at the top-right of the screen.
• If the channel you are trying to register
is already registered in one of the other
number buttons 1 to 4, “NOT
AVAILABLE” appears on the screen.
• Channels locked with the CHANNEL
GUARD function cannot be registered.
• If AUTO PROGRAM is performed,
the registered favourite channels are
reset.
Calling the favourite channel
1 In the normal screen, press the d
(favourite) button
Then “FAVOURITE1-4?” appears.
2 Press one of the number buttons 1
to 4
The called favourite channel appears on
the screen.
• If a number button in which no
channel is registered is pressed, “NO
MEMORY” appears on the screen.
Setting the picture effect
When a favourite channel has been chosen
with the d (favourite) button and number
buttons 1 to 4, picture effect settings can be
memorised for each favourite channel by
setting the picture effects in the PICTURE
menu (see page 23).
The following items in the PICTURE menu
(see page 23) are memorised.
PICTURE MODE
BACK LIGHT
CONTRAST
BRIGHT
SHARP
COLOUR
TINT
WHITE BALANCE
DIGITAL VNR
COLOUR SYSTEM
The last setting made for each item is
memorised.
ENGLISH
• When you want to delete a favourite
channel, delete the set channel and set
contents with FAVOURITE SETTING
(see page 28) in the FEATURES menu.
17
Remote control buttons and functions
Operating a JVC brand VCR or DVD player
These buttons will operate a JVC brand VCR
or DVD player. Pressing a button that looks
the same as the device’s original remote
control button has the same effect as the
ENGLISH
original remote control.
1 Set the VCR/TV/DVD switch to the
VCR or DVD position
VCR:
When you are operating the VCR, set the
switch to the VCR position.
• You can turn the VCR on or off with
the # (standby) button.
DVD:
When you are operating the DVD player,
set the switch to the DVD position.
• You can turn the DVD player on or off
with the # (standby) button.
• You can also press the H or
T button and display the
DVD disc menu screen, and then
operate by pressing the 7
buttons.
2 Press the VCR/DVD Control Button
to control your VCR or DVD player
• If your device is not made by JVC,
these buttons will not work.
• Even if your device is made by JVC,
some of these buttons may not work,
depending on the device you are using.
• You can use the p buttons to choose
a TV channel the VCR will receive, or
choose the chapter the DVD player
plays back.
• Some models of DVD player use the
p buttons for both operating the fast
forward/backward functions and for
choosing the chapter. In this case, the
253 buttons do not work.
You cannot turn the TV on or off when the
VCR/TV/DVD switch is set to the VCR or
DVD position.
When you turn the TV on or off, set the
VCR/TV/DVD switch to the TV position.
18
Teletext function
VCR/TV/
DVD
4 Choose a teletext page by pressing
the p p buttons, number buttons
or colour buttons
To return to the TV mode:
Press the b button or g (Text) button.
Basic operation
1 Choose a TV channel with a teletext
broadcast
2 Set the VCR/TV/DVD switch to the
TV position
3 Press g (Text) button to display
the teletext
Pressing g (Text) button changes the
mode as follows:
TEXT
---
TEXT
---
TV mode Text mode
• If you have trouble receiving teletext
broadcasts, consult your local dealer or
the teletext station.
• The ZOOM function will not work in
the TV and text mode or Text mode.
• You cannot operate menus when
viewing a teletext programme.
• If characters on a teletext programme
do not appear properly, change the
TELETEXT LANGUAGE setting. For
details, see “TELETEXT
LANGUAGE” on page 33.
Using the List Mode
You can store the numbers of your favourite
teletext pages in memory and call them up
quickly using the colour buttons.
To store the page numbers:
1 Press B button to go into the
List mode
The page numbers you have stored are
displayed at the bottom of the screen.
ENGLISH
19
Teletext function
2 Press a colour button to choose a
position. Then press the number
buttons to enter the page number
ENGLISH
3 Press and hold down the A (Store)
button
The four page numbers blink white to
show that they are stored in memory.
To call up a stored page:
1 Press the B button to enter the
List mode
2 Press a colour button having a
stored page
To exit the List mode:
Press the B button again.
Hold
You can hold a teletext page on the screen for
as long as you want, even while several other
teletext pages are being received.
Press the C (Hold) button
Hold indication
Sub-page
Some teletext pages include sub-pages that
are automatically displayed.
You can hold any sub-page, or view it at any
time.
1 Press the d (Favourite) button to
operate the Sub-page function
2 Press the Number buttons to enter
a sub-page number
Example:
• 3rd sub-page → press 0, 0, 0 and 3.
To cancel the Sub-page function:
Press the d (Favourite) button again.
Reveal
Some teletext pages include hidden text
(such as answers to a quiz).
You can display the hidden text.
Each time you press the E (Reveal)
button, text is hidden or revealed
Size
You can double the height of the teletext
display.
Press the F (Size) button
To cancel the Hold function:
Press C (Hold) button again.
20
Index
You can return to the index page instantly.
Press the G (Index) button
Returns to page 100 or a previously specified
page.
Cancel
You can search for a teletext page while
watching TV.
1 Press the number button to enter a
page number, or press a colour
button
The TV searches for a teletext page.
2 Press H (Cancel) button
The TV programme appears. When the
TV finds the teletext page, its page
number appears in the upper left of the
screen.
3 Press H (Cancel) button to return
to a teletext page when the page
number is on the screen
• The TV mode cannot be resumed by
pressing the H (Cancel) button. To
return to the TV mode press b
button.
Teletext function
ENGLISH
21
Using the TV’s menu
PICTURE
PICTURE
This TV has a number of functions you can
operate using menus. To use all your TV’s
functions, you need to understand the basic
menu operating techniques fully.
Buttons used to operate the menus
ENGLISH
Basic operation
1 Press the H button to display
the menu bar
D0105
-EN
2 Press the 5 buttons to choose
the menu you want to use and then
press the a button
Types of menu
PICTURE menu
D0106
Choose to set the screen
settings.
SOUND menu
D0107
Choose to set the sound settings.
FEATURES menu
D0108
Choose to set the sleep timer
and child lock settings.
SET UP menu
Choose to edit the channels or
D0109
set the display language
settings.
• The menu will disappear after about
one minute if no operation is
performed.
Operation with the buttons on the TV
You can also operate the menus using the
buttons on the front panel of the TV.
D1105
-EN
Chosen
menu
3 Press the 6 buttons to choose
the item to be set, press the 5
buttons to set the item, and then
press the a button
If there are sub-menus, use the 7
buttons to operate them.
• Press the b button to return to
the previous menu.
• Press the b or H button to exit
from the menu.
•
Some menu items may not be operated
or set depending on the TV status or
other menu item settings.
Menu items that cannot be operated or
set are displayed in grey in the menu
and cannot be chosen.
22
Chosen
menu name
TV/AV button
MENU/OK button
6 buttons
5 buttons
PICTURE menu
PICTURE
PICTURE MODE
BACK LIGHT
CONTRAST
BRIGHT
SHARP
COLOUR
TINT
WHITE BALANCE
FEATURES
D0014
-EN
OK
STANDARD
COOL
RESET
• While the PICTURE menu is displayed,
pressing the blue button will set the
BACK LIGHT, CONTRAST, BRIGHT,
SHARP, COLOUR, TINT settings to
their default settings.
• When watching the picture from VIDEO1 to VIDEO-4 or the PC, picture effect
settings can be memorised for each
external input by setting the picture
effects in the PICTURE menu.
The following items in the PICTURE
menu are memorised.
PICTURE MODE
BACK LIGHT
CONTRAST
BRIGHT
SHARP
COLOUR
TINT
WHITE BALANCE
DIGITAL VNR
COLOUR SYSTEM
The last setting made for each item is
memorised.
PICTURE MODE
You can choose one of three PICTURE
MODEs to adjust the picture settings
automatically.
BRIGHT:
Heightens contrast and sharpness.
STANDARD:
Standardizes picture adjustment.
SOFT:
Softens contrast and sharpness.
BACK LIGHT
You can adjust the back light.
2 : darker
3 : brighter
CONTRAST
You can adjust the picture contrast.
2 :lower
3 : higher
BRIGHT
You can adjust the picture brightness.
2 : darker
3 : brighter
SHARP
You can adjust the picture sharpness.
2 : softer
3 :sharper
COLOUR
You can adjust the picture colour.
2 : lighter
3 :deeper
TINT
You can adjust the picture tint.
2 : reddish
3 :greenish
• You can change the TINT setting (picture
hue) when the colour system is NTSC
3.58, or NTSC 4.43.
WHITE BALANCE
You can select one of three WHITE
BALANCE modes (three tones of white) to
adjust the white balance of the picture. Since
white is the colour which is used as a
reference for all the other colours, changing
the WHITE BALANCE mode affects the
appearance of all the other colours on the
screen.
ENGLISH
23
PICTURE menu
COOL:
A bluish white. Using this mode when
watching bright pictures allows you to enjoy
a more vivid and bright picture.
MID:
The normal white colour.
ENGLISH
WARM:
A reddish white. Using this mode when
watching films allows you to enjoy colours
that are characteristic of films.
FEATURES
Choose FEATURES and press the a or 3
button to display the sub-menu.
> FEATURES
DIGITAL VNR
COLOUR SYSTEM
OK
D1015-EN
DIGITAL VNR
The DIGITAL VNR function cuts down the
amount of ‘noise’ (‘snow’ or interference) in
the original picture.
ON:
This function is turned on.
OFF:
This function is turned off.
• This function does not work for PC
signal.
COLOUR SYSTEM
The colour system is chosen automatically.
However, if the picture is not clear or no
colour appears, choose the colour system
manually.
1 Choose COLOUR SYSTEM. Then
press the a or 3 button
The sub-menu of the COLOUR SYSTEM
function appears.
>> COLOUR SYSTEM
AUTO
OK
ON
D0016-EN
2 Press the 6 buttons to choose
the appropriate colour system.
Then press the a button
PAL:
PAL system
SECAM:
SECAM system
NTSC 3.58:
NTSC 3.58 MHz system
NTSC 4.43:
NTSC 4.43 MHz system
AUTO:
This function detects a colour system
from the input signal.
• The AUTO function may not function
properly if you have poor signal quality.
If the picture is abnormal in the AUTO
function, choose another colour system
manually.
• COLOUR SYSTEM cannot be chosen
when you are watching the PC picture.
24
SOUND menu
SOUND
STEREO/
BASS
TREBLE
BALANCE
D0019
3D SOUND
OK
-EN
OFF
• When the headphones are connected, only
“STEREO / I • II” can be used.
STEREO / I • II
When you are viewing a bilingual broadcast
programme, you can choose the sound from
Bilingual I (Sub I) or Bilingual II (Sub II).
s: Stereo sound
v : mono sound
t : Bilingual I (sub I)
u : Bilingual II (sub II)
• The sound mode you can choose differs
depending on the TV programme.
• This function does not work in the
VIDEO modes.
BALANCE
You can adjust the volume balance between
the left and right speaker.
2 : turn the left speaker’s volume level up.
3 : turn the right speaker’s volume level up.
3D SOUND
You can enjoy Surround sound with a “live”
effect by using the 3D SOUND function.
• You can choose a 3D SOUND mode from
ON, MONO and OFF modes. For details,
see “3D SOUND function” on page 16.
• You can also operate the 3D SOUND
function with the / (3D SOUND)
button. For details, see “3D SOUND
function” on page 16.
ENGLISH
BASS
You can adjust the low tone of the sound.
2 : weaker
3 :strong
TREBLE
You can adjust the high tone of the sound.
2 : weaker
3 :strong
25
FEATURES menu
FEATURES
SLEEP TIMER
CHANNEL GUARD
APPEARANCE
BLUE BACK
FAVOURITE SETTING
ENGLISH
D0023
OK
-EN
SLEEP TIMER
You can set the TV to automatically turn off
after a set period of time.
1 Choose SLEEP TIMER. Then press
the a or 3 button
A Sub-menu of the SLEEP TIMER
function appears.
SLEEP TIMER
>
0120
OFF
OK
D0024
-EN
2 Press the 5 buttons to set the
period of time.
Then press the a button
You can set the period of time for up to
120 minutes (2 hours) in 10 minute steps.
• One minute before the SLEEP TIMER
function turns off the TV, “GOOD
NIGHT!” appears.
• The SLEEP TIMER function cannot
be used to turn off the TV’s main
power.
• When the SLEEP TIMER function is
on, you can display the sub-menu of
the SLEEP TIMER function again to
confirm or change the remaining
period of time of the SLEEP TIMER
function. Press the a button to leave
the menu after confirming or changing
the remaining time.
TYPE A
ON
To cancel the SLEEP TIMER
function:
Press the 2 button to set the period of
time to “OFF”.
CHANNEL GUARD
When there is a TV channel you do not want
your children to watch, you can use the
CHANNEL GUARD function to lock out the
TV channel. Even when a child chooses a
programme number (PR) for a locked TV
channel the screen will change to blue and
display n (CHANNEL GUARD) so the TV
channel cannot be viewed. Unless you enter a
pre-set ID number by a special operation, the
lock cannot be released and the child cannot
view the TV channel.
To set the CHANNEL GUARD
function
1 Choose CHANNEL GUARD, then
press the 0 button
“SET ID NO.” (ID number setting screen)
appears.
>>
SET ID NO.
040
0
OK
D0025
-EN
2 Set the ID number to your liking
1 Press the 6 buttons to choose
a number.
2 Press the 5 buttons to move
the cursor.
26
FEATURES menu
3 Press the a button
The Sub-menu of CHANNEL GUARD
appears.
>
CHANNEL GUARD
CH/CC
ID
CH
21
CH
22
CH
23
CH
24
CH
25
CH
26
CC
01
GUARD
D1026
PR
AV
01
02
03
04
05
06
07
OK
-EN
4 Press the 6 buttons to choose a
TV channel
Every time you press the 6 buttons, the
Programme number (PR) changes, and the
picture of the TV channel registered in the
Programme number (PR) is displayed on
the screen.
5 Press the blue button and set the
CHANNEL GUARD function.
Then press the a button
n (CHANNEL GUARD) appears and the
TV channel is locked.
To reset the CHANNEL GUARD
function:
Press the blue button again.
n (CHANNEL GUARD) disappears.
To disable easy resetting of the
CHANNEL GUARD function, the menu
disappears if you choose the CHANNEL
GUARD function and press the a
button.
To view a locked TV channel
1 Choose a programme number (PR)
of a locked TV channel with the
number buttons or PR LIST
The screen changes to blue and the n
(CHANNEL GUARD) appears. You
cannot view the TV channel.
5
D0027
2 Press the h (Information) button to
display “ID NO.” (ID No. input
screen)
5
ID NO. :
D0028
-EN
3 Press the number buttons to enter
the ID number
The lock is temporarily released so you
can view the TV channel.
If you have forgotten the ID
number:
Perform step 1 of “To set the CHANNEL
GUARD function”. After confirming the
ID number, press the b button to exit
the menu.
• Even if you reset the lock temporarily,
it does not mean that the CHANNEL
GUARD function set for the TV
channel is cancelled. The next time
anyone tries to view the TV channel, it
will be locked again.
• When you want to cancel the
CHANNEL GUARD function, you
must perform the operation “To set the
CHANNEL GUARD function” again.
• To stop it being easy to choose the
programme number (PR) of a locked
TV channel, the programme number
(PR) has been set so that it cannot be
chosen with the 6 buttons or the
buttons of the TV.
• To stop it being easy to reset the lock,
“ID NO.” (ID No. input screen) is set
so that it cannot appear unless you
press the h (Information) button.
ENGLISH
27
FEATURES menu
APPEARANCE
Press the 5 button and choose the format
in which the channel number is displayed
from two types: TYPE A and TYPE B.
BLUE BACK
ENGLISH
You can set the TV to automatically change
to a blue screen and mute the sound if the
signal is weak or absent, or when there is no
input from an external device.
ON:
This function is turned on.
OFF:
This function is turned off.
FAVOURITE SETTING
Chose when deleting the favourite channels
registered in the buttons 1 to 4.
1 Choose FAVOURITE SETTING,
then press the a or 3 button
The FAVOURITE SETTING menu
appears.
FAVOURITE SETTING
D0112
1
2
3
4
OK
-EN
PR
PR 02
PR 03
PR
2 Press the 6 buttons and chose
the favourite channel that you want
to delete
3 Press the blue button
The chosen favourite channel and set
contents are deleted.
• For details of the favourite channels, see
“Favourite channel function” on page 17.
28
01
04
RESET
SET UP menu
SET UP
AUTO PROGRAM
EDIT/MANUAL
LANGUAGE
VIDEO-3 SETTING
TELETEXT LANGUAGE
OK
D0029
-EN
VIDEO
AUTO PROGRAM
You can again perform the AUTO
PROGRAM function TV channel automatic
registration which was performed in the
“Initial settings” (page 8).
1 Choose AUTO PROGRAM, then
press the a or 3 button
The AUTO PROGRAM function starts.
The TV channels you receive are
automatically stored in the programme
numbers list.
>>
AUTO PROGRAM
CH
28
14%
D0004
-EN
• To stop the AUTO PROGRAM
function, press the b button.
2 After the TV channels have been
stored in the programme number
list, the EDIT menu appears
EDIT
>
D0038
-EN
PR ID
AV
01
02
03
04
05
06
07
OK
MOVE
CH/CC
CH
CH
CH
CH
CH
CH
CC 01
ID
INSERT
21
22
23
24
25
26
MANUAL
DELETE
• You can proceed to edit the
programme numbers list using the
EDIT/MANUAL function. For details,
see “EDIT/MANUAL” on page 29.
• If a TV channel you want to view is
not stored in the programme numbers
list, you can register it using the
MANUAL function.
For details, see “EDIT/MANUAL” on
page 29.
• The AUTO PROGRAM function does
not store a TV channel to the
programme number PR 0 (AV).
• If you do not need to use the EDIT/
MANUAL function, press the a
button to exit the EDIT menu.
• Starting the AUTO PROGRAM
deletes the registered favourite
channel.
EDIT/MANUAL
The EDIT/MANUAL functions are divided
into two types:
• editing the current programme numbers
(PR) (EDIT functions); and
• manually storing a TV channel you want
to view on a particular programme
number (PR) (MANUAL function).
Here are the details about these functions:
MOVE:
This function changes the programme
number (PR) of a TV channel.
ID:
This function registers a channel name (ID)
to a TV channel.
INSERT:
This function adds a new TV channel in the
current programme numbers (PR) list by
using the CH/CC number.
• You cannot use the INSERT function if
you do not know the channel number of a
TV channel. Use the MANUAL function
to register a TV channel in the programme
number (PR).
ENGLISH
29
SET UP menu
DELETE:
This function deletes a TV channel you do
not want to list.
MANUAL:
This function manually stores a new TV
channel in a programme number (PR).
Caution
ENGLISH
• Using the MOVE, DELETE or INSERT
functions rewrites the current
programme numbers (PR) list.
Therefore, the programme numbers
(PR) of some of the TV channels will
change.
• Using the MANUAL function for a TV
channel for which the CHANNEL
GUARD function has been set cancels
the CHANNEL GUARD function for
that channel.
• When a TV channel has already been
registered in PR 99, using the INSERT
function deletes that TV channel.
Basic operation
1 Choose EDIT/MANUAL, then press
the a or 3 button
The EDIT menu appears.
EDIT
>
PR ID
AV
01
02
03
04
05
06
07
OK
MOVE
D0038
-EN
2 Follow the description for the
function you want to use
CH/CC
CH
CH
CH
CH
CH
CH
CC 01
ID
INSERT
3 Press the a button to complete
the settings
• For programme number PR 0, “AV”
appears in the programme numbers (PR)
list.
• A VIDEO terminal number does not
appear in the programme numbers (PR)
list.
MOVE
1 Press the 6 buttons to choose a
TV channel
2 Press the 3 button to start the
MOVE function
>
EDIT
PR ID
AV
01
02
03
04
05
06
07
D0030
-EN
21
22
23
24
25
26
MANUAL
DELETE
3 Press the 6 buttons to choose a
new programme number (PR)
To cancel the MOVE function:
Press the b button.
4 Press the 2 button to change the
programme number (PR) of a TV
channel to a new programme
number (PR)
CH/CC
CH
22
CH
23
CH
24
CH
25
CH
26
CC
01
OK
STORE
CH 21
30
SET UP menu
DELETE
1 Press the 6 buttons to choose a
TV channel
2 Press the yellow button to delete
the TV channel
The TV channel is deleted from the
programme numbers (PR) list.
ID
1 Press the 6 buttons to choose a
TV channel
2 Press the red button to start the ID
function
3 Press the 6 buttons to choose a
character
> EDIT
PR ID
AV
01
02
03
04
05
06
07
OK
D0032-EN
4 Press the 5 buttons to move the
cursor
5 Repeat steps 3 and 4 to complete
the channel name
6 Press the a button to give a
channel name (ID) to a TV channel
CH/CC
CH
21
CH
22
CH
23
CH
24
CH
25
CH
26
CC 01
M
INSERT
Before performing INSERT operation
• A CH/CC number unique to this TV and
corresponding to the Channel number of a
TV channel is required. Find the
corresponding CH/CC number from a
table “CH/CC numbers” on page 35 based
on the Channel number of the TV
channel.
1 Press the 6 buttons to choose a
programme number (PR) for which
you will register a new TV channel
2 Press the green button and start
the INSERT function
>
EDIT
0 9
CH/CC
CH
CH
CH
CH
CH
CH
CC
21
22
23
24
25
26
PR ID
AV
01
02
03
04
05
06
07
OK
D0034
CH/CC
-EN
3 Press the 6 buttons to choose
“CC” or “CH” according to the CH/
CC number of the TV channel
To cancel the INSERT function:
Press the b button.
4 Press the number buttons to enter
the remaining CH/CC number
The TV shifts to registration mode. When
the registration is completed, the picture
of the TV channel appears on the screen.
• The CH/CC number is a number given
to each broadcast frequency that
carries a TV channel. If the TV cannot
detect the TV channel corresponding
to the broadcast frequency indicated
by the CH/CC number, a “no-signal”
picture appears.
ENGLISH
31
SET UP menu
MANUAL
1 Press the 6 buttons to choose a
programme number (PR) for a new
TV channel
2 Press the blue button to activate
ENGLISH
the MANUAL function
At the right side following the CH/CC
number, the SYSTEM (sound system) of
the TV channel appears.
>
MANUAL
CH/CC
CH
CH
CH
CH
CH
CH
CC 01
SEARCH+
D0035
-EN
PR ID
AV
01
02
03
04
05
06
07
OK
SYSTEM
To cancel the MANUAL function:
Press the b button.
3 Press the 3 button to choose the
SYSTEM (sound system) for a TV
channel you want to register
• For the sound systems in each country
or region, refer to the table below:
Area Country or Region System
Bahrain, Kuwait, Oman,
Qatar, United Arab Emirates,
Yemen, etc.
Indonesia, Malaysia,
Singapore, Thailand, India,
Asia,
Middle
East
Europe
Oceania Australia, New Zealand, etc. B/G
Africa
etc.
China, Vietnam, etc. D/K
Hong Kong, etc. I
Islamic Republic of Iran,
Lebanon, Saudi Arabia, etc.
Philippines, Taiwan,
Myanmar, etc.
Russia, etc. D/K
Czech Republic, Poland, etc. D/K
Germany, Holland, Belgium,
etc.
UK, etc. I
Republic of South Africa, etc. I
Nigeria, etc. B/G
Egypt, Morocco, etc. B/G
SEARCH-
4 Press the green or red button to
search for a TV channel
Scanning stops when the TV finds a TV
channel. Then the TV channel is
displayed.
5 Press the green or red button
repeatedly until the TV channel you
want appears
If the TV channel reception is poor:
Press the blue or yellow button to finetune the TV channel.
21
22
23
24
25
26
(
)
B / G
FINE-
FINE+
If you cannot hear the normal
sound even when the picture of the
TV channel appears normally:
The SYSTEM setting is wrong. Press the
3 button and choose a SYSTEM that has
normal sound.
6 Press the a button and register
the TV channel to a Programme
number (PR)
The normal EDIT menu is resumed.
B/G
B/G
M
B/G
32
SET UP menu
GE
LANGUAGE
The LANGUAGE setting which was
performed in the “Initial settings” (page 8)
can be changed.
1 Choose LANGUAGE, then press
the a or 3 button
A sub-menu of the LANGUAGE function
appears.
LANGUA
D1002-EN
2 Press the 6 buttons to choose a
language. Then press the a
button
VIDEO-3 SETTING
Set the VIDEO-3 SETTING correctly
according to the video signal input from the
external device connected to the VIDEO-3
terminal. If this setting is incorrect, images
will not be displayed.
VIDEO:
If a normal video signal (composite video
signal) is input.
S-VIDEO:
If a S-VIDEO signal (Y/C signal) is input.
• If you set S-VIDEO in VIDEO-3
SETTING, the display on the screen
changes from V3 to S3.
TELETEXT LANGUAGE
There are four types of teletext language
groups. Set the teletext language group that
corresponds to the language of the teletext
programme that you want to watch.
1 Choose TELETEXT LANGUAGE,
then press the a or 3 button
> TELETEXT LANGUAGE
GROUP-1
GROUP-2
GROUP-3
GROUP-4
OK
D1003
-EN
2 Press the 6 buttons to choose a
group
Group Languages
GROUP-1 Turkish, Hungarian, English,
GROUP-2 Polish, Serbian, Croatian,
GROUP-3 Russian, Bulgarian, Lettish,
GROUP-4 Arabic, Czech, Slovak. Hungarian,
3 Press the a button to complete
the setting
The menu disappears.
• Languages that are not included in the
German, French, Italian, Spanish,
Portuguese, Greek, Swedish,
Finnish
Slovenian, Czech, Slovak,
Rumanian, Hungarian, German,
French, Italian, Swedish, Finnish
Lithuanian, Estonian, Ukrainian,
Serbian, Croatian, Slovenian,
Czech, Slovak, English, German
English, German, French, Italian,
Spanish, Portuguese, Swedish,
Finnish
teletext language group that you select,
the sub-titles of the teletext programme
will not be displayed properly.
ENGLISH
33
Displaying a computer screen
This TV can be used as a computer screen.
Connecting to the computer
Use a D-SUB cable to connect the TV’s PC
IN terminal to the computer’s analogue RGB
output terminal.
If you want to listen to the sound from the
ENGLISH
computer, use an audio cable to connect the
VIDEO-3 AUDIO L/R sound input terminal
to the computer’s sound output terminal.
When the sound from the computer is mono,
connect to the VIDEO-3 AUDIO L terminal.
• Refer to the computer manual for a
detailed explanation of the connections at
the computer side.
• Ensure that the connectors are facing the
correct way when connecting.
• After connecting the D-SUB cable,
tighten the two screws to fix the connector
in place.
Watching images from a computer
After starting the computer, press the
G or p p buttons to choose “PC”
“PC” is after VIDEO-4.
You can listen to the sound when the
sound from the computer is connected to
the VIDEO-3 AUDIO L/R sound input
terminal.
• When the sound from the computer is
connected to VIDEO-3, by choosing
external input VIDEO-3 the sound
from the computer can be listened to,
but the images from the computer
cannot be seen.
Table of signals for each type of computer
Resolution Vertical
640 × 480
(VGA)
1024 × 768
(XGA)
• Only the above formats are supported.
• Even with the above formats and at
60 Hz, some problems may be
experienced depending on the quality of
the synchronous signal. (Depending on
the quality, some pictures may not be
displayed properly.)
• Apple Macintosh
supported.
When a picture is not displayed
Check the computer’s refresh rate and set it
to 60 Hz. Refer to the computer’s instruction
manual.
Computers which cannot have their refresh
rate set to 60 Hz cannot be used with this
unit.
frequency
(Hz)
60.0 31.5
60.0 42.0
*
computers are not
Horizontal
frequency
(kHz)
34
* Apple Macintosh is a registered
trademark of Apple Computer, Inc.
CH/CC numbers
When you want to use the INSERT function on page 31, find the CH/CC number corresponding to
the Channel number of the TV channel from this table.
US: The US channel numbers are the channel numbers used in the United States,
Philippines, etc.
CCIR: The CCIR channel numbers are the channel numbers used in the Middle East,
OIRT: The OIRT channel numbers are the channel numbers used in Eastern Europe, Russia,
AUSTRALIA: The AUSTRALIA channel numbers are the channel numbers used in Australia, etc.
CH
CH02 US-2 E2 R1 AU-0
CH03 US-3 E3 AU-1
CH04 US-4 E4 R2 AU-2
CH05 US-5 E5 R6 AU-6
CH06 US-6 E6 R7 AU-7
CH07 US-7 E7 R8 AU-8
CH08 US-8 E8 R9 AU-9
CH09 US-9 E9
CH10 US-10 E10 R10 AU-10
CH11 US-11 E11 R11 AU-11
CH12 US-12 E12 R12
CH13 US-13
CH14 US-14, W+29
CH15 US-15, W+30
CH16 US-16, W+31
CH17 US-17, W+32
CH18 US-18, W+33
CH19 US-19, W+34
CH20 US-20, W+35
CH21 US-21, W+36 E21
CH22 US-22, W+37 E22
CH23 US-23, W+38 E23
CH24 US-24, W+39 E24
CH25 US-25, W+40 E25
CH26 US-26, W+41 E26
CH27 US-27, W+42 E27
CH28 US-28, W+43 E28
CH29 US-29, W+44 E29
CH30 US-30, W+45 E30
CH31 US-31, W+46 E31
CH32 US-32, W+47 E32
CH33 US-33, W+48 E33
CH34 US-34, W+49 E34
CH35 US-35, W+50 E35
CH36 US-36, W+51 E36
CH37 US-37, W+52 E37
CH38 US-38, W+53 E38
CH39 US-39, W+54 E39
CH40 US-40, W+55 E40
CH41 US-41, W+56 E41
CH42 US-42, W+57 E42
CH43 US-43, W+58 E43
CH44 US-44, W+59 E44
CH45 US-45, W+60 E45
CH46 US-46, W+61 E46
CH47 US-47, W+62 E47
CH48 US-48, W+63 E48
CH49 US-49, W+64 E49
CH50 US-50, W+65 E50
CH51 US-51, W+66 E51
CH52 US-52, W+67 E52
CH53 US-53, W+68 E53
CH54 US-54, W+69 E54
CH55 US-55, W+70 E55
CH56 US-56, W+71 E56
CH57 US-57, W+72 E57
CH58 US-58, W+73 E58
CH59 US-59, W+74 E59
CH60 US-60, W+75 E60
CH61 US-61, W+76 E61
CH62 US-62, W+77 E62
CH63 US-63, W+78 E63
CH64 US-64, W+79 E64
CH65 US-65, W+80 E65
CH66 US-66, W+81 E66
CH67 US-67, W+82 E67
CH68 US-68, W+83 E68
CH69 US-69, W+84 E69
Southeast Asia, etc.
Vietnam, etc.
US CCIR OIRT AUSTRALIA
Channel
CC
CC01 S-1 AU-5
CC02 S-2
CC03 S-3
CC04 S-4
CC05 S-5
CC06 S-6 AU-5A
CC07 S-7
CC08 S-8
CC09 S-9
CC10 S-10
CC11 S-11
CC12 S-12
CC13 S-13
CC14 A S-14
CC15 B S-15
CC16 C S-16
CC17 D S-17
CC18 E S-18
CC19 F S-19
CC20 G S-20
CC21 H S-21
CC22 I S-22
CC23 J S-23
CC24 K S-24
CC25 L S-25
CC26 M S-26
CC27 N S-27
CC28 O S-28
CC29 P S-29
CC30 Q S-30
CC31 R S-31
CC32 S S-32
CC33 T S-33
CC34 U S-34
CC35 V S-35
CC36 W S-36
CC37 W+1 S-37
CC38 W+2 S-38
CC39 W+3 S-39
CC40 W+4 S-40
CC41 W+5 S-41
CC42 W+6
CC43 W+7
CC44 W+8
CC45 W+9
CC46 W+10
CC47 W+11
CC48 W+12
CC49 W+13
CC50 W+14
CC51 W+15
CC52 W+16
CC53 W+17
CC54 W+18
CC55 W+19
CC56 W+20
CC57 W+21
CC58 W+22
CC59 W+23
CC60 W+24
CC61 W+25
CC62 W+26
CC63 W+27
CC64 W+28
CC75 X
CC76 Y R3
CC77 Z R4 AU-3
CC78 Z+1 R5
CC79 Z+2 AU-4
CC95 A-5
CC96 A-4
CC97 A-3
CC98 A-2
CC99 A-1
US CCIR OIRT AUSTRALIA
Channel
ENGLISH
35
Troubleshooting
If a problem arises while you are using the TV, please read this troubleshooting guide carefully
before you ask to have the TV repaired. You may be able to fix it easily by yourself. For example,
if the mains plug is disconnected from the mains outlet, or the TV aerial has problems, you may
think there is a problem with the TV itself.
Important:
• This troubleshooting guide only covers problems whose causes are not easy to decide. If you
ENGLISH
have a question when you are operating a function, read the page(s) for that function carefully,
not this troubleshooting guide.
• If you follow the advice in this troubleshooting guide without any success, unplug the mains
plug and ask for your TV to be repaired. Do not attempt to repair the TV by yourself or to
remove the rear cover of the TV.
If you cannot turn on the TV
• Is the mains plug connected to the mains
outlet?
• Make sure you set the VCR/TV/DVD
switch to the TV position. You cannot
turn the TV on when the VCR/TV/DVD
switch is set to the VCR or DVD position.
If you cannot turn off the TV
• Make sure you set the VCR/TV/DVD
switch to the TV position. You cannot
turn the TV off when the VCR/TV/DVD
switch is set to the VCR or DVD position.
No picture or no sound
• Have you chosen a TV channel with very
poor reception? If so, the BLUE BACK
function will be activated: the entire
screen becomes blue, and the sound is
muted. If you still want to view the TV
channel, follow the description “BLUE
BACK” on page 28 to change the BLUE
BACK function setting to OFF.
• If the SYSTEM setting for a TV channel
is incorrect, it may prevent the sound
from being issued. Follow the description
“EDIT/MANUAL” on page 29 to use the
MANUAL function to try to change the
SYSTEM setting.
Poor picture
• If noise (snow) totally blocks out the
picture, there may be a problem with the
aerial or aerial cable. Check the following
to try to solve the problem:
– Have the TV and aerial been connected
properly?
– Has the aerial cable been damaged?
– Is the aerial pointing in the right
direction?
– Is the aerial itself faulty?
• If the TV or aerial suffers interference
from other equipment, stripes or noise
may appear in the picture. Move any
equipment such as an amplifier, personal
computer, or a hair drier, that can cause
interference away from your TV. Or try
moving the TV. If the aerial suffers
interference from a radio tower or highvoltage wire, please contact your local
dealer.
• If the TV suffers interference from signals
reflecting from mountains or buildings,
double-pictures (ghosting) will occur. Try
to change the aerial’s direction or replace
it with one with better directionality.
• Are your COLOUR SYSTEM settings
correct? Follow the description
“COLOUR SYSTEM” on page 24 to try
to solve the trouble.
• Have the COLOUR and BRIGHT settings
been adjusted properly? Follow the
description “BRIGHT” and “COLOUR”
on page 23 to try to adjust them properly.
• Videotaping teletext is not recommended
because it may not record correctly.
36
Troubleshooting
• When viewing images from commercially
available video software products, or
videos from videotapes which have been
recorded improperly, the top of the image
may be distorted. This is due to the
condition of the video signal. There is
nothing wrong with the TV.
• Since this TV is designed to make full use
of the resolution of the original video
source, the motion may appear unnatural
when the video source is input with
progressive-scanning component signals.
If this occurs, change the output setting of
the connected device to interlacescanning component signal output. See
the instructions that came with the device
for more information.
Poor sound
• Have you adjusted BASS or TREBLE
properly? If not, follow the description
“BASS” or “TREBLE” on page 25.
• When TV channel reception is poor, it can
be hard to hear stereo or bilingual sound.
In this case, follow the description
“STEREO / I • II” on page 25 to hear the
sound more easily by changing it to a
mono sound.
If the TV does not respond to the
remote control
• Have the batteries of the remote control
worn out? Follow the description “Putting
the batteries into the remote control” on
page 8 and replace them with new batteries.
• Have you attempted to use the remote
control from the sides or rear of the TV or
from more than seven metres away from the
TV? Use the remote control in front of your
TV or from less than seven metres away.
• When you are viewing a teletext
programme, you cannot operate the
menus. Press the b button to return to
the ordinary TV programme, and then try
operating the menus.
• If the TV suddenly stops responding,
disconnect the power cord of the TV from
the AC outlet. Connect them to the AC
outlet again to turn on the TV. If the TV
returns to a normal state, it is not a failure.
Other issues
• When the SLEEP TIMER function
operates, the TV is automatically turned
off. If the TV suddenly turns off, try to
press the # (standby) button to turn on
the TV once again. If the TV goes back to
normal, there is no problem.
• It takes a short period of time from the
time an operation such as changing
channels is performed until an image is
displayed. This is not a fault. This is the
time needed for the image to stabilise
before it can be displayed.
• The TV may make a crackling sound due
to a sudden change in temperature. The
picture or sound may be normal. If you
hear crackling sounds frequently while
you are viewing the TV, there may be
other causes. As a precaution, ask your
service technician to inspect it.
• The top of the TV and the screen may
become hot during use but this has no
affect on the performance of the TV.
Make sure that the ventilation holes are
not blocked.
• When the picture is unstable, the screen
may become white for a moment. This
happens when the signal which drives the
liquid crystal is missing. This is not a
fault.
• When a still image has been displayed for
a long period, a faint residual image may
remain on the screen for a short time after
the power has been turned off or when
another image is displayed. This is not a
fault and the image will eventually
disappear.
ENGLISH
37
Specifications
Model LT-32AX5
Broadcasting systems B, G, I, D, K, M
Colour systems PAL, SECAM, NTSC 3.58/4.43 MHz
Channels and frequencies VHF low channel (VL) = 46.25 to 168.25 MHz
Sound-multiplex systems NICAM (B/G, I, D/K) system, A2 (B/G, D/K) system
ENGLISH
Languages displayed by
teletext
Teletext systems FLOF (Fastext), WST (World Standard System)
Power requirements 110 - 240 V AC, 50/60 Hz
Power consumption
[Standby]
Screen size Viewable area 80 cm (measured diagonally)
Audio output Rated Power output: 5 W + 5 W
Speakers 6.6 cm round × 2
VIDEO-1 terminal Euroconnector (21-pin, SCART)
VIDEO-2 terminal Euroconnector (21-pin, SCART)
VIDEO-3 terminal RCA connectors × 3
VIDEO-4 terminal RCA connectors × 3
PC IN terminal Analogue RGB D-SUB (15 pin) × 1
Headphone jack Stereo mini-jack (3.5 mm in diameter)
Dimensions (W × H × D)
[without stand]
Weight
[without stand]
Accessories Remote control unit × 1 (RM-C1816)
We may change the design and specifications without notice.
VHF high channel (VH) = 175.25 to 463.25 MHz
UHF channel (U) = 471.25 to 863.25 MHz
• Receives cable channels in mid band (X to Z+2, S1 to S10), super band (S11
to S20) and hyper band (S21 to S41).
Please see the table in the description “TELETEXT LANGUAGE” on page 33.
158 W
[2.1 W]
• Video input and Audio L/R inputs are available.
• Monitor outputs (Video and Audio L/R) are available.
• Video input and Audio L/R inputs are available.
• Monitor outputs (Video and Audio L/R) are available.
S-VIDEO connector × 1
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.
• Component video (Y, Pb, Pr) input.
• Input signal types
480i/ 50Hz, 480p/ 50Hz, 576i/ 60Hz, 576p/ 60Hz, 720i/ 50Hz, 720p/ 60Hz,
1080i/ 50Hz, 1080i/ 60Hz.
• Audio L/R input uses the Audio L/R of the VIDEO-3 terminal.
• PC signal is available. Refer to page 34 for details of the signals which can be
input.
• Audio L/R input uses the Audio L/R of the VIDEO-3 terminal.
820 mm × 604 mm × 308 mm
[820 mm × 551 mm × 127 mm]
20 kg
[16.5 kg]
AA/R6 dry cell battery × 2
SCART - RCA cable (for input/output) × 2
38
Model LT-26AX5
Broadcasting systems B, G, I, D, K, M
Colour systems PAL, SECAM, NTSC 3.58/4.43 MHz
Channels and frequencies VHF low channel (VL) = 46.25 to 168.25 MHz
Sound-multiplex systems NICAM (B/G, I, D/K) system, A2 (B/G, D/K) system
Languages displayed by
teletext
Teletext systems FLOF (Fastext), WST (World Standard System)
Power requirements 110 - 240 V AC, 50/60 Hz
Power consumption
[Standby]
Screen size Viewable area 60 cm (measured diagonally)
Audio output Rated Power output: 5 W + 5 W
Speakers 6.6 cm round × 2
VIDEO-1 terminal Euroconnector (21-pin, SCART)
VIDEO-2 terminal Euroconnector (21-pin, SCART)
VIDEO-3 terminal RCA connectors × 3
VIDEO-4 terminal RCA connectors × 3
PC IN terminal Analogue RGB D-SUB (15 pin) × 1
Headphone jack Stereo mini-jack (3.5 mm in diameter)
Dimensions (W × H × D)
[without stand]
Weight
[without stand]
Accessories Remote control unit × 1 (RM-C1816)
VHF high channel (VH) = 175.25 to 463.25 MHz
UHF channel (U) = 471.25 to 863.25 MHz
• Receives cable channels in mid band (X to Z+2, S1 to S10), super band (S11
to S20) and hyper band (S21 to S41).
Please see the table in the description “TELETEXT LANGUAGE” on page 33.
125 W
[2.1 W]
• Video input and Audio L/R inputs are available.
• Monitor outputs (Video and Audio L/R) are available.
• Video input and Audio L/R inputs are available.
• Monitor outputs (Video and Audio L/R) are available.
S-VIDEO connector × 1
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.
• Component video (Y, Pb, Pr) input.
• Input signal types
480i/ 50Hz, 480p/ 50Hz, 576i/ 60Hz, 576p/ 60Hz, 720i/ 50Hz, 720p/ 60Hz,
1080i/ 50Hz, 1080i/ 60Hz.
• Audio L/R input uses the Audio L/R of the VIDEO-3 terminal.
• PC signal is available. Refer to page 34 for details of the signals which can be
input.
• Audio L/R input uses the Audio L/R of the VIDEO-3 terminal.
686 mm × 527 mm × 308 mm
[686 mm × 474 mm × 122 mm]
16 kg
[12.5 kg]
AA/R6 dry cell battery × 2
SCART - RCA cable (for input/output) × 2
We may change the design and specifications without notice.
Specifications
ENGLISH
39
ENGLISH
40
© 2005 Victor Company of Japan, Limited
0805HHH-CR-JMT
Loading...