JVC KW-AVX900 User Manual
DVD RECEIVER WITH MONITOR
KW-AVX900
For canceling the display demonstration, see page 8.
For installation and connections, refer to the separate manual.
INSTRUCTIONS
LVT1670-001A
[A]
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best
possible performance from the unit.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to
qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical
instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
Cautions on the monitor:
• The monitor built in this unit has been produced
with high precision, but it may have some
ineffective dots. This is inevitable and is not
malfunction.
• Do not expose the monitor to direct sunlight.
• Do not operate the touch panel using a ball-point
pen or similar tool with the sharp tip.
Touch the buttons on the touch panel with your
finger directly (if you wear a glove, take it off).
• When the temperature is very cold or very hot..
– Chemical changes occur inside, causing
malfunction.
– Pictures may not appear clearly or may move
slowly. Pictures may not be synchronized with
the sound or picture quality may decline in
such environments.
[European Union only]
WARNINGS:
To prevent accidents and damage
• DO NOT install any unit and wire any cable in
locations where;
– it may obstruct the steering wheel and
gearshift lever operations.
– it may obstruct the operation of safety devices
such as air bags.
– it may obstruct visibility.
• DO NOT operate the unit while driving.
If you need to operate the unit while driving, be
sure to look around carefully.
• The driver must not watch the monitor while
driving.
• The driver must not put on the headphones while
driving.
2
How to reset your unit
• Your preset
adjustments will also
be erased.
How to forcibly eject a disc
ENTER
NO EJECT?
EMERGENCY EJECT?
Back
2
at the same time
11
• If this does not work, reset the unit.
For safety...
• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operations.
Temperature inside the car...
If you have parked the car for a long time in hot or cold
weather, wait until the temperature in the car becomes
normal before operating the unit.
3
Exit
Contents
INTRODUCTION
Playable disc type ............................ 4
Basic operations—
Monitor panel/touch panel ............ 5
Basic operations—
Remote controller (RM-RK251) ...... 6
OPERATIONS
Before operating the unit ................ 8
Common operations ........................ 9
Listening to the radio ...................... 10
Disc operations ................................ 13
Dual Zone operations ....................... 27
SD operations .................................. 30
USB operations ................................ 32
Watching TV .................................... 34
EXTERNAL DEVICES
Bluetooth® operations—
Cellular phone/audio player .......... 37
Listening to the CD changer .............. 44
Listening to the iPod/D. Player ......... 46
Using other external components ..... 48
SETTINGS
Sound equalization .......................... 51
Assigning titles to the sources .......... 52
Menu operations ............................. 53
REFERENCES
Maintenance ................................... 63
More about this unit ........................ 64
Troubleshooting .............................. 71
Specifications .................................. 76
3
INTRODUCTION
Playable disc type
Disc type Recording format, file type, etc. Playable
DVD DVD Video (Region Code: 4)*
DVD Audio
DVD-ROM
DVD Recordable/Rewritable
(DVD-R*2/-RW, +R/+RW*3)
• DVD Video: UDF bridge
• DVD-VR
• DivX/MPEG1/MPEG2/JPEG/MP3/
WMA/WAV/AAC: ISO 9660 level
1, level 2, Romeo, Joliet
• DVD-RAM cannot be played.
DVD Video
DVD-VR (non-CPRM only)
DivX/MPEG1/MPEG2
JPEG
MP3/WMA/WAV/AAC*
MPEG4
DVD+VR
Dual Disc DVD side
Non-DVD side
CD/VCD Audio CD/CD Text (CD-DA)/DTS-CD
VCD (Video CD)
CD-ROM
CD-I (CD-I Ready)
CD Recordable/Rewritable
(CD-R/-RW)
• ISO 9660 level 1, level 2, Romeo,
Joliet
CD-DA
MP3/WMA/WAV/AAC*
JPEG
DivX/MPEG1/MPEG2
MPEG4
*1 If you insert a DVD Video disc of an incorrect Region Code, “Region code error” appears on the monitor.
*2 DVD-R recorded in multi-border format is also playable (except for dual layer discs).
*3 It is possible to play back finalized +R/+RW (Video format only) discs. However, the use of +R double layer disc is
not recommended.
*4 This unit can play back AAC files encoded using iTunes.
1
4
4
Caution for DualDisc playback
The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore,
the use of Non-DVD side of a DualDisc on this product may not be recommended.
4
Basic operations — Monitor panel/touch panel
Display <AV Menu>.
• ☞ page 53.
Display <Source Menu>.
• ☞ pages 9 and 27.
Display and erase the Short Cut windows.
Available functions vary among the sources. For details, see each source
operation section.
Change the display information.
Change the sources.
• ☞ page 9.
Display <AV Menu>.
• ☞ page 53.
• Turn on the power.
• Turn off the power [Hold].
• Attenuate the sound (if the power is on).
Reset the unit.
• Use only when the internal system malfunctions.
• For details on the touch panel operations,
see each source operation sections.
Adjust the volume.
• Display the <Open/Tilt> screen
• Eject the disc and display the <Open/Tilt>
screen [Hold].
• Close the monitor panel when the <Open/Tilt>
screen is displayed.
• [OPEN]: Open the monitor panel.
• [EJECT]: Eject the disc.
• [CLOSE]: Close the monitor panel.
• [TILT +/–]: Tilt the monitor panel.
• [Exit]: Erase this screen.
• Shaded icons cannot be used at that time.
5
Remote sensor
INTRODUCTION
Basic operations — Remote controller (RM-RK251)
Installing the battery
R03/LR03/AAA
If the range or effectiveness of the remote controller
decreases, replace both batteries.
Before using the remote controller:
• Aim the remote controller directly at the remote
sensor on the unit.
• DO NOT expose the remote sensor to bright light
(direct sunlight or artificial lighting).
Caution:
• Do not expose batteries to heat or flame.
IMPORTANT:
If Dual Zone is activated (☞ page 27), the remote
controller functions only for operating the DVD/CD
player and the built-in TV.
Main elements and features
i
o
;
a
s
1*1 • Turns on the power.
• Attenuates the sound if the power is on.
• Turns off the power if pressed and held (while
the power is on).
2*1 Selects the source.
3*1 • Displays <Dial Menu>.
• Displays <Redial> list if pressed and held.
• Answers incoming calls.
1,2
4*
Adjusts the volume level.
6
1,2
5*
Selects surround mode.
6 • DVD/DivX 6: Shows the disc menu.
• VCD: Resumes PBC playback.
• DVD-VR: Shows the Original Program screen.
7 • Makes selection/settings.
• ~: Skips back or forward by 5 minutes for
DivX/MPEG1/MPEG2.
• DISC +/– buttons: Changes discs for “CD-CH.”
8 Shows the on-screen bar.
1
Changes the display information.
9*
p Display or erase <AV Menu>.
q For disc/SD/USB operations:
• 6: Plays/pauses.
• 5 / ∞:
DVD: Selects the title/group.
DVD-VR: Selects the program/playlist.
SD/USB/other discs (except VCD/CD): Selects
the folders.
• 4 / ¢:
– Press briefly: reverse skip/forward skip.
– Press and hold: reverse search/forward
search.
For FM/AM operations:
• 5 / ∞: Selects the preset stations.
• 4 / ¢: Functions to search for stations.
– Press briefly: Auto Search
– Press and hold: Manual Search
For TV operations:
• 5 / ∞: Selects the preset stations.
• 4 / ¢: Functions to search for stations.
– Press briefly: Auto Search
– Press and hold: Manual Search
For Apple iPod/JVC D. player operations:
• ∞: Pauses/stops or resumes playback.
• 5: Enters the main menu (then 5 / ∞ /
4 / ¢ work as the menu selecting
3
buttons).*
• 4 / ¢ (in menu selecting mode)
– Selects an item if pressed briefly. (Then,
press ∞ to confirm the selection.)
– Skips 10 items at a time if pressed and held.
For Bluetooth operations:
• 4 / ¢: reverse skip/forward skip (for
audio operation)
• 6: Answers incoming calls (for “Bluetooth
PHONE”), plays/pauses (for “Bluetooth
AUDIO”)
w TUNER: Selects the bands.
DISC/SD/USB: Stops play.
Bluetooth PHONE: Ends the call.
Bluetooth AUDIO: Plays/pauses.
• This button does not function as the BACK
button for this model.
e*2 Adjusts the volume level through the 2nd AUDIO
OUT plug.
2
Activates or deactivates Dual Zone.
r*
1,2
t*
Selects the sound mode.
y • DVD Video/DivX 6: Shows the disc menu.
• VCD: Resumes PBC playback.
• DVD-VR: Shows the Play List screen.
u RETURN button
• For VCD: Returns to the PBC menu.
i DISC/SD/USB: Switches number entry mode.
• Also functions as CLEAR button to erase the
misentry after entering the wrong number.
o • Enter the numbers.
• FM/AM/TV: Selects the preset station/channel
directly.
• CD changer: Selects the disc directly.
;*1 Changes the aspect ratio of the playback
pictures.
a Reverse search/forward search for disc/SD/USB
operations.
s • DVD Video: Selects audio language ( ),
subtitles ( ), angle ( ).
• DVD Audio: Selects audio stream ( ).
• DVD-VR: Turn on/off subtitles ( ), and
selects audio channel ( )
• DivX: Selects audio language ( ),
subtitles ( ).
• VCD: Selects audio channel ( ).
*1 If Dual Zone is activated, these buttons cannot be
used.
*2 These buttons can be used only when the slide cover is
closed.
*3 5 : Returns to the previous menu.
∞ : Confirms the selection.
7
INTRODUCTION
Before operating the unit
Cancel the display demonstration and set the clock (☞
pages 54 and 55 for details).
• Non-available items will be displayed being shaded
on the AV Menu screens.
Indication language:
In this manual, English indications are used
for purpose of explanation. You can select the
indication language on the monitor. (☞ page 55)
~ Turn on the power.
Ÿ Display <AV Menu>.
! Display the <Setup> menu.
@ Set the clock settings.
Moves to the preceding menu page
Moves to the succeeding menu page
¤ Finish the procedure.
⁄ Cancel the display demonstrations.
Select <Off>.
Return to the previous screen.
8
Common operations
Selecting the playback source
• Available sources depend on the external
components you have connected, media you have
attached, and the <Input> settings you have made
(☞ pages 58 and 59).
On the touch panel:
☞ page 27
On the monitor panel:
Exit
Changing the display
information
• Available display information varies among the
playback sources.
On the monitor panel only:
• Each time you press DISP, the display changes to
show the various information.
Ex. When the playback source is a DivX disc.
Playback picture screen
(only for video sources)
Source information screen
Preset station (service) list,
track (file) list, or phone
number list
TUNER = DISC (DVD/VCD/CD) = SD = USB =
CD-CH, iPod, D.PLAYER, or EXT-IN = Bluetooth
PHONE = Bluetooth AUDIO = TV = AV-IN =
(back to the beginning)
• You cannot select these sources if they are not ready.
Back to the beginning
9
Animation screen
Navigation screen
(When <
Navigation> is
selected for <
(
☞ page 58).
AV Input>):
OPERATIONS
Listening to the radio
Preset No.
Band
Sound mode
☞ page 51)
(
Tuner indicators
☞ page 9
~
Press [SOURCE], then press [TUNER]. (☞ page 9)
• You can also use SOURCE on the monitor panel. Press it repeatedly.
Assigned station name (
“No Name” appears.
☞ page 52). If no name is assigned,
☞ page 11, 51
: Buttons on the
touch panel. In the
explanation, they
are indicated inside
[ ].
Ÿ Press [BAND].
! Press [4] or [¢] to search for a station—Auto Search.
• Manual Search: Hold either [4]or [¢] until “Manual Search” appears on the display, then press it
repeatedly.
• The ST indicator lights up when receiving an FM stereo broadcast with sufficient signal strength.
When an FM stereo broadcast is
hard to receive
1 Press [AV MENU].
3
• You can also use AV MENU on the monitor panel.
2 Press [Mode].
Reception improves, but stereo effect will be lost.
• The MONO indicator lights up.
To restore stereo effect, select <Off>.
10
Tuning in to stations with
sufficient signal strength
This function works only for FM bands. Once you have
activated this function (selected <Local>), it always
works when searching for FM stations.
1 Press [AV MENU].
FM station automatic presetting
—SSM (Strong-station
Sequential Memory)
This function works only for FM bands.
You can preset six stations for each band.
1 Press [AV MENU].
• You can also use AV MENU on the monitor panel.
2 Press [Mode].
3
Only stations with sufficient signal strength will be
detected.
• The DX indicator goes off, then the LO indicator
lights up.
• You can also change <IF Band Width> setting
(for details, ☞
<IF Band Width> menu can be accessed by
pressing [SHORT CUT] on the touch panel,
then...
page 58).
☞ page 51
• You can also use AV MENU on the monitor panel.
2 Press [Mode].
3
Local FM stations with the strongest signals are
searched and stored automatically in the FM band.
11
OPERATIONS
Manual presetting
Ex.: Storing FM station of 92.5 MHz into preset
number 4 of the FM1 band.
1 Display the Preset List.
2 Tune in to a station you want to preset.
3 Select a preset number.
Selecting preset stations
On the remote:
1
2
or
On the unit:
To select directly on the touch panel
To select from the Preset List
1
2
The station selected in step 2 is now stored in
preset number 4.
12
Disc operations
The disc type is automatically detected, and playback starts automatically (for some discs: automatic start depends
on its internal program).
If a disc does not have any disc menu, all tracks in it will be played repeatedly until you change the source or eject the
disc.
” appears on the monitor, the unit cannot accept the operation you have tried to do.
If “
• In some cases, without showing “ ,” operations will not be accepted.
~ Open the monitor panel.
<Open/Tilt> menu appears.
• Shaded icons cannot be used at that time.
• By pressing and holding the button, you can
open the monitor panel and eject the disc.
Ÿ Press [OPEN].
Caution on volume setting:
Discs produce very little noise compared with other
sources. Lower the volume before playing a disc
to avoid damaging the speakers by the sudden
increase of the output level.
! Insert a disc.
Label side
Monitor panel closes automatically.
If not, press [CLOSE].
Caution:
Do not place your finger behind the monitor panel.
• [OPEN]: Open the monitor panel.
• [EJECT]: Eject the disc.
• [CLOSE]: Close the monitor panel.
• [TILT +/–]: Tilt the monitor panel.
• [Exit]: Erase this screen.
13
OPERATIONS
While playing the following discs, press .
• Each time you press the button, the display changes to show the different information (☞ page 9).
DVD Video: Title no./Chapter no./Playing time
DVD-VR: Program no. (or Playlist no.)/Chapter no./Play time
1
Disc type *
Audio format
Playback mode
Speaker/signal
indicators
(
☞ page 64)
: Buttons on the touch panel. In the explanation,
they are indicated inside [ ].
These buttons also work when they are not
shown on the touch panel (while watching
pictures on the screen).
BONUS indicator
(
☞ page 23)
[3 / 8] Start and pause playback
[
7] Stop playback
[
4 ¢] Press: Select track
Hold: Reverse/forward search
[5 ∞] Select group
3 / 8] Start and pause playback
[
[
7] Stop playback
[
4 ¢] Press: Select chapter
Hold: Reverse/forward search
[5 ∞] Select title/program/playlist
Group no./Track no./Playing time
2
*
Sampling frequency/Bit
rate/Recorded signal
channel no.
Surround mode
(
☞ page 24)
☞ page 19
2
*
Reproduced sound
indicator—
MULTI CH/LR ONLY
(
☞ page 65)
B.S.P indicator
(
☞ page 23)
☞ page 19
*1 DVD-VR also indicates either PRG (program) or PLAY (playlist) playback.
*2 Search speed: x2 ] x10.
14
While playing the following discs, press .
• Each time you press the button, the display changes to show the different information (☞ page 9).
For DivX/MPEG1/MPEG2: Folder no./Track no./Playing time
For JPEG: Folder no./Track no.
Disc type
(☞ page 24)
3
Total track no.
included in the
disc
Surround mode *
[
3 / 8] Start and pause playback
[
7] Stop playback
[
4 ¢] Press: Select track
Hold: Reverse/forward search for DivX/MPEG1/MPEG2
[5 ∞] Press: Select folder
Hold: Display Folder list
Track no./Playing time
PBC indicator
lights up when PBC is
in use.
[3 / 8] Start and pause playback
[
7] Stop playback
[
4 ¢] Press: Select track
Hold: Reverse/forward search
*2 Search speed: x2 ] x10.
*3 Surround mode and sound mode cannot be used at the same time.
*4 Search speed: ¡1 ] ¡2.
☞ page 19
4
*
Total track no.
included in the disc
Total play time
☞ page 19
2
*
15
OPERATIONS
Track no./Playing time
Sound mode *
3
(☞ page 51)
☞ page 19
[
3 / 8] Start and pause playback
[
7] Stop playback
[
4 ¢] Press: Select track
Hold: Reverse/forward search
Audio format
(MP3/WMA/WAV/AAC)
• While playing a DTS-CD
2
*
DTS indicator
Speaker/signal
indicators
(
☞ page 64)
Folder no./Track no./Playing time
Only for CD Text
Total track no.
included in the disc
Total play time
Tag data appears
only when it is
recorded
5
*
☞ page 19
3 / 8] Start and pause playback
[
[
7] Stop playback
[4 ¢] Press: Select track
Hold: Reverse/forward search
[5 ∞] Press: Select folder
Hold: Display Folder list
*2 Search speed: x2 ] x10.
*5 “No Name” appears for conventional CDs.
Total track no. included in the disc
2
*
16
Operation buttons on the monitor screen
You can display the following operation buttons while watching the playback pictures on the monitor.
• While the operation buttons are displayed, aspect ratio is fixed to <Full> (☞ page 55).
• If no operation is done for about 5 seconds, the operation buttons disappears (except when a disc menu is
displayed).
☞ pages 20 to 22 on how the operation buttons
particularly work for a variety of the discs
To erase the operations, touch the screen again.
A
Touch the screen (center portion).
*
Touch [KEY].
Touch [KEY].
Touch [KEY].
[SOURCE] Display the <Source Menu>
[
AV MENU] Display the <AV Menu>
[
SHORT CUT] Display the Short Cut buttons
[
3 / 8] Start and pause playback
[
7] Stop playback
[
4 ¢] Press: Select track
Hold: Reverse/forward search
[
5 ∞] Select folders
• The above buttons also work when they are not shown on
the touch panel (while watching pictures on the screen).
* While a disc menu is played back for DVD, [KEY] is
automatically displayed. On the disc menu, you can select a
menu item directly by touching it on the screen.
B
For DVD/VCD/DivX menu operation playback
[
2 3 5 ∞] Select the menu items
[
ENT] Confirm the selection
[
TOP MENU] Display the disc menu
[
MENU] Display the disc menu
[
RETURN] Return to the previous menu or display the
menu (only for VCD with PBC)
C
For entering the numbers
[
DIRECT CLR] Switch between chapter/track entry and
Erase the last entry when you enter a wrong
[
0]–[9]=[ENT] Enter the number
Ex. To enter “105”: press [
title/group/folder entry
number
1], [0], [5], then [ENT]
17
OPERATIONS
Selecting playback modes
You can use only one of the following playback modes—Intro/Repeat/Random.
Ex. To select Track Repeat
1
• You can also use AV MENU on the monitor panel.
2
Disc type Intro Repeat Random
—
— Track: Repeats current track —
—
Track: Plays the first 15
seconds of each track (for
VCD: PBC not in use)
3
When one of the playback modes is selected, the
corresponding indicator lights up on the source
information screen.
To cancel, select <Off>.
Chapter: Repeats current
chapter
Title: Repeats current title
Chapter: Repeats current
chapter
Program: Repeats current
program (not available for
Playlist playback).
Track: Repeats current track*
(for VCD: PBC not in use)
1
Disc (All): Randomly plays all
tracks (for VCD: PBC not
in use)
—
—
Track: Plays the first 15
seconds of each track
Folder: Plays the first 15
seconds of the first track of
each folder
—
—
1
You can also use [SHORT CUT] to turn on and off Track Repeat
*
Track: Repeats current track*
Folder: Repeats all tracks of
the current folder
Track: Repeats current track
Folder: Repeats current folder
Folder: Repeats current folder
18
1
Folder: Randomly plays all
tracks of current folder,
then tracks of next folders
Disc (All): Randomly plays all
tracks
—
—
Selecting tracks on the list
If a disc includes folders, you can display the Folder/
Track (File) Lists, then start playback.
1
• You can also use AV MENU on the monitor panel.
2
3
Select a folder (1), then a track (2).
Selected track starts playing. (* Press to move to
the previous/next pages of the list)
1 Current folder list number/total folder list
number
2 Current track list number/total track list
number of the current folder
• Track List can also be accessed by pressing DISP
on the monitor panel.
Prohibiting disc ejection
You can lock a disc in the loading slot.
at the same time
To cancel the prohibition, repeat the same
procedure to select <EJECT OK?>.
Using Short Cut Icons
You can easily access the some frequently used
functions by using [SHORT CUT] on the touch panel.
1
2
• For video software:
Aspect ratio
☞ page 55)
(
Surround
(
☞ page 24)
Sound mode
(
☞ page 51)
• For audio software:
Selected track starts playing.
19
Turn on or off Track Repeat
(Repeat play:
☞ page 18)
OPERATIONS
Operations using the remote controller—RM-RK251
: Stop playback.
: Start playback/pause (if pressed during playback).
: Reverse/forward search*2. (No sound can be heard.)
(Slow motion*3 during pause. No sound can be heard.)
: Press: Select chapter (during playback or pause).
Hold: Reverse/forward search*4.
: Select title (during playback or pause).
1
*
*1 Erases the misentry of the
number.
*2 Search speed: x2 ] x5 ]
x10 ] x20 ] x60
*3 Slow motion speed: 1/32 ]
1/16 ] 1/8 ] 1/4 ] 1/2
*4 Search speed: x2 ] x10
*5 Search speed: ¡1 ]
¡2 ] ¡3
*6 Search speed: ¡1 ]
¡2
= = :
Select chapter.
Select title (when not playing).
(twice) = = :
Select title (during playback or pause).
: Select aspect ratio.
: Select audio language.
: Select subtitle language.
: Select view angle.
: Stop playback.
: Start playback/pause (if pressed during playback).
: Reverse/forward search*2.
: Press: Select track.
Hold: Reverse/forward search*4.
: Select group.
= = :
Select track.
(twice) = = :
Select group.
: Select aspect ratio.
: Select audio stream.
Using menu driven
features
1
2 Select an item you want
to start play.
3
Using menu driven
features
1
2 Select an item you want
to start play.
3
20
: Stop playback.
: Start playback/pause (if pressed during playback).
: Reverse/forward search*5. (No sound can be heard.)
: Press: Select track.
Hold: Reverse/forward search*
6
. (No sound can be heard.)
: Select folder.
= = :
Select track (within the same folder).
(twice) = = :
Select folder.
For DivX6: Using menu driven features
1
2 Select an item you want to start play.
3
: Stop playback.
: Start playback/pause (if pressed during
playback).
: Reverse/forward search*2. (No sound
can be heard.)
(Slow motion*3 during pause. No sound
can be heard.)
• Reverse slow motion does not work.
: Press: Select chapter (during playback or
pause).
Hold: Reverse/forward search*4.
: Select program.
Select playlist (during playback or
pause).
: Select aspect ratio.
: Select audio channel (ST: stereo, L: left,
R: Right).
: Select aspect ratio.
: Select audio language. (DivX only)
: Select subtitle language. (DivX only)
While playing...
Back/advance the scenes by 5 minutes.
Current playback position
2nd press
1st press
1st press
2nd press
3rd press
: Turn on/off subtitle.
= = :
Select chapter.
Select program (when not playing).
(twice) = = :
Select program/playlist (during playback or
pause).
Using Original Program/Play List screens
( ☞ page 23)
1 : For Original Program
: For Play List
2 Select an item you want to start playing.
3 To erase the screen.
21
OPERATIONS
: Stop playback.
: Start playback. (Slide show: each file is
shown for a few seconds.)
Shows the current file until you change it
if pressed during Slide show.
: Select track.
: Stop playback.
: Start playback/pause (if
pressed during playback).
: Reverse/forward search*2.
: Press: Select track.
Hold: Reverse/forward search*4.
: Select folder.
: Select aspect ratio.
= = :
Select track (within the same folder).
(twice) = = :
Select folder.
: Stop playback.
: Start playback/pause (if pressed during
playback).
: Reverse/forward search*2.
(Forward slow motion*3 during pause. No
sound can be heard.)
• Reverse slow motion does not work.
: Press: Select track.
Hold: Reverse/forward search*4 (No
sound can be heard.)
: Select aspect ratio.
: Select audio channel (ST: stereo, L: left, R:
Right).
: Stop playback.
: Start playback/pause (if pressed during playback).
: Reverse/forward search*2.
: Press: Select track.
Hold: Reverse/forward search*
4
.
= = :
Select track.
: Select folder.
= = :
Select track (within the same folder).
(twice) = = :
Select folder.
= = :
Select track.
During PBC playback...
= = :
Select an item on the menu.
To return to the previous menu, press
To cancel PBC playback
1
2 Start the desired track.
= =
• To resume PBC, press / .
*2 Search speed: x2 ] x5 ] x10 ] x20 ] x60
*3 Slow motion speed: 1/32 ] 1/16 ] 1/8 ]
1/4 ] 1/2
*4 Search speed: x2 ] x10
.
22
Playing back a bonus group
If a DVD Audio including a “bonus group” is
detected, the BONUS indicator lights up on the source
information screen.
To play a bonus group...
1 Select the bonus group.
• The bonus group is usually recorded as the last
group.
2 Enter the key number.
: Move the entry position
: Select a number
• “key number” (a kind of password) for the bonus
group is not open to public. The way of getting
the key number depends on the disc.
3 Follow the interactive instructions shown on
the monitor.
Selecting browsable still picture
When a disc including browsable still pictures is
detected, the B.S.P indicator lights up on the source
information screen.
When disc shows the BSP selecting icons such as @ or
# on the screen...
1 Select an item you want to display.
2
Using the list screens
You can use Original Program and Play List screen
anytime while playing DVD-VR with its data recorded.
1 Display the Original Program/Play List
screen.
2 Select an item you want.
To erase the screen
1 Program/Play list number
2 Recording date
3 Recording source (TV station, the input terminal of
the recording equipment, etc.)
4 Start time of recording
5 Title of the program/play list*
6 Highlight bar (current selection)
7 Creating date of play lists
8 Total number of chapters included in the playlist
9 Playback time
* The title of the original program or play list may not be
displayed depending on the recording equipment.
23
OPERATIONS
Enjoying surround sounds
You can enjoy multi-channel surround playback
through the front, center, surround speakers.
• After connecting the center speaker, make
sure to activate the center speaker; otherwise,
no sound comes out of the center speaker (☞
page 57).
• Surround mode can also be used for “USB” and “SD.”
4
MULTI: For multi-channel encoded sources such as
Dolby Digital*
activated, “MULTI” is shown on the source
information screen.)
Dolby Pro Logic II (Movie/Music): For 2 channel
sources except for DivX/MPEG1/MPEG2 discs.
To turn on the surround...
1
, DTS*2, and DVD Audio. (When
1
• You can also use AV MENU on the monitor panel.
2
3
• Auto: When multi-channel digital signals come
in, “MULTI” surround is activated.
When 2-channel or 2.1-channel signals come in,
“4CH STEREO” is activated.
• Through: All incoming channel signals are sent
to the corresponding speakers.
• Dolby PL II Movie: Activates Dolby Pro Logic
Movie.
• Dolby PL II Music: Activates Dolby Pro Logic
II Music. You can adjust <Panorama> and
<Center Width> setting (☞below).
Only when selecting <Dolby PL II Music>
After step 4 above...
1 Activate <Panorama>.
II
• Off: Deactivates surround.
• On: Activates surround = go to the following
steps.
• Panorama: Select <On> to add wraparound
sound effect.
24
2 Adjust <Center Width>.
Operations using the on-screen
bar
These operations are possible on the monitor using
the remote controller, while playing the following
discs—DVD/VCD/DivX/MPEG1/MPEG2/JPEG.
1 Display the on-screen bar. (☞page 26)
• Center Width: Adjust the center image so it
may be heard only from the center speaker,
only form the left/right front speaker as a
“phantom” center image, or various combination
of these speakers. As the number increases, the
“phantom” effect becomes stronger (normally
select <04>).
On the remote controller:
• You cannot change the <Dolby PL II Music>
settings using the remote controller.
*1 Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.
*2 “DTS” and “DTS Digital Surround” are registered
trademarks of DTS, Inc.
2 Select an item.
3 Make a selection.
If a pop-up menu appears...
• For entering time/numbers...
To remove the on-screen bar
25
: Move the entry position
: Select a number
Continued on the next page
OPERATIONS
Loading...