Other TerminalsSUBWOOFER OUTChanger control, Steering wheel remote input
TUNER SECTION
Frequency RangeFM87.5 MHz to 108.0 MHz
AM(MW) 522 kHz to 1 620 kHz
(LW) 144 kHz to 279 kHz
FM TunerUsable Sensitivity11.3 dBf (1.0
50 dB Quieting Sensitivity16.3 dBf (1.8
Alternate Channel Selectivity (400 kHz) 65 dB
Frequency Response40 Hz to 15 000 Hz
Stereo Separation35 dB
Capture Ratio1.5 dB
MW TunerSensitivity20 µV
Selectivity65 dB
LW TunerSensitivity50
CD/SD PLAYER SECTION
TypeCompact disc player
Signal Detection SystemNon-contact optical pickup (semiconductor laser)
Number of Channels2 channels (stereo)
Frequency Response5 Hz to 20 000 Hz
Dynamic Range98 dB
Signal-to-Noise Ratio102 dB
Wow and FlutterLess than measurable limit
MP3 (MPEG Audio Layer 3)Max. Bit Rate320 kbps
WMA (Windows Media Audio)Max. Bit Rate192 kbps
Playable SD CardFormatFAT 12/16
StorageUp to 512 MB
Playable Audio Format for SD CardMP3/WMA
GENERAL
Power RequirementOperating VoltageDC 14.4 V (11 V to 16 V allowance)
Grounding SystemNegative ground
Allowable Operating Temperature0
Dimensions (W
Mass (approx.)1.7 kg (excluding accessories)
× H × D)Installation Size (approx.)182 mm × 52 mm × 159 mm
Panel Size (approx.)188 mm
°C to +40°C
Ω load (full scale)
Ω
µV/75 Ω)
µV/75 Ω)
µV
× 58 mm × 13 mm
• Design and specifications are subject to change without notice.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
• SD logo is a trademark.
Ω, 40 Hz to 20 000 Hz at no more than 0.8% total
Ω, 40 Hz to 20 000 Hz at no more than 0.8% total
1-2 (No.MA192)
1.1Safety Precautions
SECTION 1
PRECAUTIONS
!
!
Burrs formed during molding may be left over on some parts of the chassis. Therefore,
pay attention to such burrs in the case of preforming repair of this system.
Please use enough caution not to see the beam directly or touch it in case of an
adjustment or operation check.
(No.MA192)1-3
1.2Preventing static electricity
Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser
diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
1.2.1 Grounding to prevent damage by static electricity
Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players.
Be careful to use proper grounding in the area where repairs are being performed.
(1) Ground the workbench
Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the
traverse unit (optical pickup) on it.
(2) Ground yourself
Use an anti-static wrist strap to release any static electricity built up in your body.
(caption)
Anti-static wrist strap
1M
Conductive material
(conductive sheet) or iron plate
(3) Handling the optical pickup
• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical
pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)
• Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily
destroy the laser diode.
1.3Handling the traverse unit (optical pickup)
(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.
(2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the
replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a
time when attaching it to the connector.
(3) Handle the flexible cable carefully as it may break when subjected to strong force.
(4) It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.
1.4Attention when traverse unit is decomposed
*Please refer to "Disassembly method" in the text for the CD pickup unit.
• Apply solder to the short land before the flexible wire is disconnected from the connector on the CD pickup unit.
(If the flexible wire is disconnected without applying solder, the CD pickup may be destroyed by static electricity.)
• In the assembly, be sure to remove solder from the short land after connecting the flexible wire.
Short sections
Flexible wire
1-4 (No.MA192)
CN601
Mechanism control board
1.5Important for laser products
!
1.CLASS 1 LASER PRODUCT
2.DANGER : Invisible laser radiation when open and inter
lock failed or defeated. Avoid direct exposure to beam.
3.CAUTION : There are no serviceable parts inside the
Laser Unit. Do not disassemble the Laser Unit. Replace
the complete Laser Unit if it malfunctions.
4.CAUTION : The CD,MD and DVD player uses invisible
laser radiation and is equipped with safety switches which
prevent emission of radiation when the drawer is open and
the safety interlocks have failed or are defeated. It is
dangerous to defeat the safety switches.
5.CAUTION : If safety switches malfunction, the laser is able
to function.
6.CAUTION : Use of controls, adjustments or performance of
procedures other than those specified here in may result in
hazardous radiation exposure.
Please use enough caution not to
see the beam directly or touch it
in case of an adjustment or operation
check.
REPRODUCTION AND POSITION OF LABELS
WARNING LABEL
CAUTION : Visible and Invisible
CLASS 1
LASER PRODUCT
laser radiation when open and
interlock failed or defeated.
AVOID DIRECT EXPOSURE TO
BEAM. (e)
ADVARSEL : Synlig og usynlig
laserstråling når maskinen er
åben eller interlocken fejeler.
Undgå direkte eksponering til
stråling. (d)
VARNING : Synlig och
osynling laserstrålning när
den öppnas och spärren är
urkopplad. Betrakta ej
strålen. (s)
VARO : Avattaessa ja suojalukitus
ohitettuna tai viallisena olet alttiina
näkyvälle ja näkymättömälle
lasersäteilylle. Vältä säteen
kohdistumista suoraan itseesi. (f)
(No.MA192)1-5
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.
1-6 (No.MA192)
SECTION 3
DISASSEMBLY
3.1Main body section
3.1.1 Removing the front panel assembly
(See Fig.1)
(1) Push the detach button in the lower right part of the front
panel assembly.
(2) Remove the front panel assembly.
3.1.2 Removing the heat sink
(See Fig.2)
Reference:
Remove the front panel assembly as required.
(1) From the left side of the main body, remove the two screws
A and three screws B attaching the heat sink.
(2) Remove the heat sink from the main body.
Front panel assembly
Detach button
Fig.1
AAB
Heat sink
Fig.2
(No.MA192)1-7
3.1.3 Removing the top chassis assembly
(See Figs.3 to 6)
• Prior to performing the following procedures, remove the heat
sink.
Reference:
Remove the front panel assembly as required.
(1) From the bottom side of the main body, remove the two
screws C attaching the top chassis assembly to the bottom
chassis assembly. (See Fig.3)
(2) From the both and rear sides of the main body, remove the
five screws D attaching the top chassis assembly to the
bottom chassis assembly. (See Figs.4 to 6)
(3) Lift the top chassis assembly in the direction of the arrow,
disconnect the connector CN503
trol board from the connector CN721 on the main board.
(See Figs.4 to 6)
(4) Take out the top chassis assembly from the bottom chassis
assembly.
on the mechanism con-
Bottom chassis assembly
C
C
Top chassis assembly
Fig.3
Top chassis assembly
CN503
CN721
Main board
Bottom chassis assembly
Top chassis assembly
Main board
Bottom chassis assembly
Mechanism control board
D
Fig.4
Mechanism control board
CN503
D
CN721
Fig.5
1-8 (No.MA192)
Bottom chassis assembly
Top chassis assembly
DD
Rear bracket
Fig.6
D
3.1.4 Removing the front chassis assembly
(See Figs.7 and 8)
• Prior to performing the following procedure, remove the front
panel assembly, heat sink and top chassis assembly.
(1) From the both sides of the top chassis assembly, remove
the two screws E attaching the front chassis assembly.
(2) Remove the front chassis assembly from the top chassis
assembly.
Top chassis assembly
E
Front chassis assembly
Fig.7
Top chassis assembly
E
Front chassis assembly
3.1.5 Removing the CD mechanism assembly
(See Fig.9)
• Prior to performing the following procedures, remove the front
panel assembly, heat sink and top chassis assembly.
Reference:
Remove the front chassis assembly as required.
(1) From the inside of the top chassis assembly, remove the
three screws F attaching the CD mechanism assembly.
(2) Release the mecha heat sink from the slots a on the mech-
anism control board and remove the mecha heat sink from
the main body.
(3) Take out the CD mechanism assembly from the top chas-
sis.
Top chassis
Fig.8
Mechanism control board
Mecha heat sink
F
a
FF
CD mechanism assembly
Fig.9
(No.MA192)1-9
3.1.6 Removing the main board
(See Figs.10 and 11)
• Prior to performing the following procedures, remove the front
panel assembly, heat sink and top chassis assembly.
(1) From the rear side of the bottom chassis assembly, remove
the two screws G attaching the rear bracket to the bottom
chassis assembly. (See Fig.10)
(2) From the top side of the bottom chassis assembly, remove
the two screws H attaching the main board to the bottom
chassis assembly. (See Fig.11)
(3) Release the stopper of the connector CN701
board in an upward direction, disconnect the card wire from
the connector CN701
(4) Disconnect the wire from the connector of the front door
mechanism assembly. (See Fig.11)
(5) Disconnect the wire from the connector CN911
board. (See Fig.11)
Reference:
After connecting the wires, fix the wires with the wire
holders.
(6) Take out the main board from the bottom chassis assem-
bly.
. (See Fig.11)
on the main
on the main
Rear bracket
G
Front door mechanism assembly
Connector
Wire holders
Bottom chassis assembly
Fig.10
Card wire
CN701
Stopper
Bottom chassis assembly
H
3.1.7 Removing the rear bracket
(See Fig.12)
• Prior to performing the following procedures, remove the front
panel assembly, heat sink, top chassis assembly and main
board.
(1) Remove the two screws J and three screws K attaching the
wires to the rear bracket.
(2) Remove two screws M attaching the wire bracket to the
rear bracket.
(3) From the rear side of the main board, remove the wires
from the rear bracket in the direction of the arrow.
Reference:
After attaching the rear bracket to the main board, pass the
wires through the wire bracket and insert them into the slots of
the rear bracket.
H
M
JK
CN911Main board
Fig.11
Wire bracket
Wire
Rear bracket
Fig.12
1-10 (No.MA192)
3.1.8 Removing the front door mechanism assembly
(See Fig.13)
• Prior to performing the following procedures, remove the front
panel assembly, heat sink, top chassis assembly and main
board.
(1) From the top side of the bottom chassis assembly, remove
the screw N attaching the FPC guide to the bottom chassis.
(2) Remove the five screws P attaching the front door mecha-
nism assembly to the bottom chassis.
Reference:
When attaching the screws N and P, apply a locking
agent them.
(3) Take out the front door mechanism assembly from the bot-
tom chassis.
Front door mechanism assembly
Bottom chassis
3.1.9 Removing the switch board
(See Figs.14 to 16)
• Prior to performing the following procedures, remove the front
panel assembly.
(1) From the rear side of the front panel assembly, remove the
six screws Q attaching the rear cover to the front panel assembly. (See Fig.14)
(2) Release the two joints b of the front panel assembly and re-
move the rear cover. (See Fig.15.)
(3) Take out the switch board from the front panel assembly.
(See Fig.16)
Note:
When removing the rear cover assembly and switch board, be
careful not to lose the spring.
P
Q
FPC guide
Fig.13
Rear cover assembly
Fig.14
Rear cover assembly
P
N
Q
Q
Spring
Joints b
Front panel assembly
Joints b
Fig.15
Switch board
Fig.16
(No.MA192)1-11
3.2CD mechanism assembly section
• Remove the CD mechanism assembly from the main body.
(See "Removing the CD mechanism assembly".)
3.2.1 Removing the mechanism control board
(See Fig.1)
(1) From the bottom side of the CD mechanism assembly, sol-
der the short sections on the flexible wire.
Caution:
Solder the short sections on the flexible wire before disconnecting the flexible wire from the connector CN601
on the mechanism control board. If you do not follow this
instruction, the CD pickup may be damaged.
(2) Disconnect the flexible wire from the connector CN601
the mechanism control board.
(3) Disconnect the flexible wire from the connector CN602
the mechanism control board.
(4) Remove the solders from the soldered sections a on the
mechanism control board and remove the wires of the feed
motor.
(5) Remove the solders from the soldered sections b on the
mechanism control board, and remove each wire of the
spindle motor and other parts.
(6) Remove the five screws A attaching the mechanism con-
trol board.
Caution:
When reassembling, remove the solders from the short sections after connecting the flexible wire to the connector CN601
on the mechanism control board.
on
on
Short sections
Flexible wire
CN601
A
CD mechanism assembly
A
A
Spindle motor
Mechanism control board
Fig.1
Feed motor
b
A
a
A
CN602
1-12 (No.MA192)
3.2.2 Removing the top cover
r
(See Fig.2)
(1) From the back side of the CD mechanism assembly, re-
move the two screws B attaching the top cover.
(2) Take out the top cover in an upward direction.
Reference:
When attaching the top cover, set the sections c of the top cover under the bending sections d of the chassis base 2.
3.2.3 Removing the mechanism section
(See Figs.2 to 4)
• Remove the mechanism control board and top cover.
(1) From the front side of the CD mechanism assembly, re-
move the two screws C attaching the right and left stoppers. (See Fig.2.)
(2) Remove the two floating springs on the bottom side of the
CD mechanism assembly. (See Fig.3.)
(3) Take out the mechanism section in an upward direction
and remove the three damper springs from the dampers.
(See Fig.4.)
Caution:
• When reassembling the mechanism section, reattach the
damper springs to the dampers respectively and insert the
three shafts on the bottom of the mechanism section to the
dampers. (See Fig.4.)
• Before inserting the shaft to the dampers, apply IPA to the
hole of damper.
B
Top cover
c
B
Damper
spring(F)
(Green)
Floating spring
Fig.3
Mechanism section
Damper
spring(R)
(Red)
Dampe
(Yellow)
C
Stopper
C
Stopper
Fig.2
Chassis base 2
d
Damper
(Black)
Damper
spring(F)
(Green)
Damper
(Black)
Fig.4
(No.MA192)1-13
3.2.4 Removing the clamper unit
(See Figs.5 and 6)
• Remove the mechanism control board, top cover and mecha-
nism section.
(1) From the bottom side of the mechanism section, remove
the clamper 2 spring. (See Fig.5.)
(2) Release section e of the clamper spring from the bending
section of the CD chassis assembly. (See Fig.6.)
(3) Move the clamper unit 2 in the direction of the arrow and
release the joints (f, g). (See Fig.5.)
(4) Take out the clamper unit 2 in an upward direction. (See
Fig.5.)
3.2.5 Reattaching the clamper unit
(See Figs.5 to 9)
(1) From the bottom side of the mechanism section, attach the
clamper spring to the clamper unit 2. (See Figs.5 and 9.)
(2) Move the clamper unit 2 to set the joints (f, g) to each pro-
jection of the CD chassis assembly. (See Fig.5.)
(3) Make sure that section h of the clamper unit 2 is inserted to
the notch of the CD chassis assembly. (See Figs.5 and 8.)
(4) Move the clamper spring to the outside of the bending part
of the CD chassis assembly. (See Fig.6.)
Caution:
When reattaching the clamper unit 2, temporarily hook
the end of the clamper spring as shown in the figure to
make the work easy. (See Fig.9.)
(5) Attach the clamper 2 spring to the CD chassis assembly
and clamper unit 2. (See Figs.5 and 7.)
Clamper spring
f
Clamper 2 spring
CD chassis assembly
Clamper unit 2
h
g
Fig.5
Clamper spring
CD chassis assembly
e
Fig.6
1-14 (No.MA192)
Clamper 2 spring
Clamper unit 2
CD chassis assembly
Fig.7
Clamper unit 2
Clamper unit 2
Notch
h
Fig.8
Fig.9
Clamper spring
(No.MA192)1-15
3.2.6 Removing the front unit
(See Figs10 to 12)
• Remove the mechanism control board, top cover and mecha-
nism section.
(1) From the bottom side of the mechanism section, remove
the double-stick tape fixing the flexible wire. (See Fig.10.)
(2) From the top side of the mechanism section, remove the
screw D attaching the front unit 2. (See Figs.11 and 12.)
(3) Move the front unit 2 toward the front to release the joint i.
(See Figs.11 and 12.)
(4) Release two joints j and k on the right side of the CD chas-
sis assembly. (See Fig.12.)
(5) Take out the front unit 2 in an upward direction.
(6) Remove the double-stick tape fixing the flexible wire and
remove the two screws E attaching the switch wire. (See
Fig.12.)
Reference:
You can remove the switch wire only without removing the
front unit 2.
Double-stick tape
Front unit 2
Flexible wire
Fig.10
D
Double-stick tape
Flexible
wire
j
k
i
Fig.11
E
Switch wire
D
Front unit 2
1-16 (No.MA192)
CD chassis assembly
Fig.12
i
3.2.7 Removing the loading arm assembly
(See Figs.13 and 14)
• Remove the mechanism control board, top cover, mechanism
section and front unit 2.
(1) From top side of the mechanism section, move the loading
arm assembly in the direction of the arrow. (See Fig.13.)
(2) Release the projections from the right and left joints (m, n)
of the CD chassis assembly. (See Figs.13 and 14.)
(3) Release the projection from notch p of the connect arm on
the right side of the mechanism section and release the
projection from notch q of the slide cam assembly on the
left side. (See Figs.13 and 14.)
Loading arm assembly
n
CD chassis assembly
p
m
Fig.13
Loading arm assembly
Side cam
assembly
q
n
CD chassis assembly
Fig.14
m
p
Connect arm
(No.MA192)1-17
3.2.8 Removing the rod (L), rod (R) and roller assembly
(See Figs.15 and 16)
• Remove the mechanism control board, top cover, mechanism
section, front unit and loading arm assembly.
(1) From the bottom side of the loading arm assembly, release
the rod (L) and (R) from the joints r. (See Fig.15.)
(2) Remove the roller assembly from the loading arm assem-
bly. (See Fig.16.)
(3) Remove the two collars and washer from the roller assem-
bly. (See Fig.16.)
Caution:
After attaching the roller assembly to the loading arm assembly, attach the rod (L) and (R). Then attach the rods to the right
and left collars of the roller assembly. (See Fig.15.)
Collar
Rod(R)Rod(L)
r
Rod(R)
Roller assembly
Loading arm assembly
r
Collar
Rod(L)
r
r
Fig.15
Collar
Rod(L)
Washer
Roller assembly
Rod(R)
Collar
Loading arm assembly
Fig.16
1-18 (No.MA192)
3.2.9 Removing the CD pickup
(See Figs.17 to 19)
• Remove the mechanism control board.
(1) From the bottom side of the CD mechanism assembly, turn
the feed gear in the direction of the arrow to move the CD
pickup assembly outwards. (See Fig.17.)
(2) Remove the screw F and remove the thrust spring. (See
Fig.17.)
(3) Remove the CD pickup assembly in an upward direction
from the side of L.S. gear and release the CD pickup assembly from joint s of the sub guide. (See Fig.18.)
(4) Move the lead screw of the CD pickup assembly in the di-
rection of the arrow to release at joint t. (See Fig.18.)
(5) Remove the screw G attaching the CD rack spring and CD
rack plate on the CD pickup assembly. (See Fig.19.)
(6) Pull out the lead screw. (See Fig.19.)
Caution:
• When attaching the CD pickup assembly, attach the CD
pickup assembly at joint s of sub guide first, and attach the
lead screw to the joint t on the L.S.holder 2. (See Fig.18.)
• Perform electric adjustment after replacing the pickup.
CD mechanism assembly
CD pickup assembly
Thrust spring
L.S.holder 2
Fig.17
t
Lead screw
Feed gear
F
CD Pickup assembly
Sub guide
s
CD rack spring
CD rack plate
L.S. Gear
Fig.18
G
Lead screw
CD Pickup
Fig.19
(No.MA192)1-19
3.2.10 Removing the spindle motor
r
r
(See Fig.20)
• Remove the mechanism control board, top cover, mechanism
section and clamper unit.
(1) From the top side of the mechanism section, remove the
T.table assembly and washer from the spindle motor.
(2) Remove the two screws H attaching the spindle motor.
(3) Take out the spindle motor from the bottom side of the
mechanism section.
Caution:
Perform adjustment when reattaching the spindle motor.
3.2.11 Removing the feed motor
(See Figs.21 and 22)
• Remove the mechanism control board.
(1) From the bottom side of the CD mechanism assembly, re-
move the feed TRI. spring. (See Fig.21.)
(2) Remove the two screws J attaching the feed motor assem-
bly. (See Fig.21.)
(3) Remove the slit washer from the motor H. assembly and
pull out the worm wheel. (See Fig.22.)
(4) Remove the two screws K attaching the feed motor. (See
Fig.22.)
T. table assembly
Washer
H
Spindle moto
Fig.20
J
Feed TRI. spring
Feed motor assembly
1-20 (No.MA192)
Fig.21
Slit washer
Worm wheel
Feed moto
K
Motor H. assembly
Fig.22
3.2.12 Removing the SW board and rest SW board
(See Fig.23)
• Remove the mechanism control board.
(1) From the bottom side of the CD mechanism assembly, re-
move the screw L attaching the SW board.
(2) Remove the screw M attaching the rest SW board.
CD mechanism assembly
ML
Rest SW boardSW board
Fig.23
(No.MA192)1-21
SECTION 4
ADJUSTMENT
4.1Adjustment method
Test instruments required for adjustment
(1) Digital oscilloscope (100MHz)
(2) Electric voltmeter
(3) Digital tester
(4) Tracking offset meter
(5) Test Disc JVC :CTS-1000
(6) Extension cable for check
EXTDV001-20P × 1
Standard volume position
Balance and Bass &Treble volume : lndication"0"
Loudness : OFF
How to connect the extension cable for adjusting
Caution:
Be sure to attach the heat sink and rear bracket onto the power amplifier IC and regulator IC respectively, before supply the power.
If voltage is applied without attaching these parts, the power amplifier IC and regulator IC will be destroyed by heat.
Standard measuring conditions
Power supply voltageDC14.4V(11 to 16V)
Load impedance20KΩ(2 Speakers connection)
Output LevelLine out 5.0V (Vol. MAX)
Dummy load
Exclusive dummy load should be used for AM,and FM. For FM
dummy load,there is a loss of 6dB between SSG output and
antenna input.The loss of 6dB need not be considered since
direct reading of figures are applied in this working standard.
Extension cable: EXTDV001-20P
Heat sink
Rear bracket
1-22 (No.MA192)
4.2Service mode
4.2.1 Service mode setting
(1) Turn ON power
(2) Pressing both the DISP button and BAND button.
(3) Set to service mode
CURSOR button : BACK
CURSOR button : NEXT
OK button : SET
OK
CURSOR
SERVICE MODE (MENU)
SERVICE MODE
RUNNING MODE
DATA CLEAR
ROM COLLECTION
DSP TUNER S MODE
DSP TUNER ADJUST
SMTH1=******
Select the value with
"CURSOR" button.
SMTH2=******
Select the value with
"CURSOR" button.
MP=******
Select the value with
"CURSOR" button.
ADJ=******
Select the value with
"CURSOR" button.
SM L=******
Select the value with
"CURSOR" button.
SMM1=******
Select the value with
"CURSOR" button.
SMM2=******
Select the value with
"CURSOR" button.
DSP TUNER AJUST
AUTO ADJUSTMENT
MANUAL ADJUSTMENT
RDS model only
1.FM DAA
87.5MHz
2.FM DAA
97.9MHz
3.FM DAA
108.0MHz
4.FM S.MATER
97.9MHz
5.FM S.MATER
97.9MHz 7
40dBuV 0%
40dBuV 0%
40dBuV 0%
40dBuV 0%
0dBuV 0%
1.FM DAA
87.5MHz
2.FM DAA
97.9MHz
3.FM DAA
108.0MHz
4.FM S.MATER
97.9MHz
5.FM S.MATER
97.9MHz 7
40dBuV 0%
40dBuV 0%
40dBuV 0%
40dBuV 0%
High or Low or No Signal
0dBuV 0%
High or Low or No Signal
No Signal
No Signal
No Signal
1-26 (No.MA192)
6.FM FULL SEPARATION
97.9MHz 7
Lch 40MHz mod 1kHz
0dBuV 0%
GH
6.FM FULL SEPARATION
97.9MHz 7
0dBuV 0%
Adjustment NG or No Signal
J
GH
J
7.FM IF COUNTER
97.9MHz 7
8.AM S.METER
999kHz 26
9.AM S.METER
999kHz 56
10.AM IF COUNTER
999kHz 56
AUTO ADJUSTMENT
COMPLETED
0dBuV 0%
dBuV 0%
dBuV 0%
dBuV 0%
MANUAL ADJUSTMENT
1.FM DAA
87.5MHz
2.FM DAA
97.9MHz
40dBuV 0%
40dBuV 0%
Press OK
Press OK
7.FM COUNTER
97.9MHz 7
8.AM S.METER
999kHz 26
9.AM S.METER
999kHz 56
10.AM IF COUNTER
999kHz 56
1.FM DAA
87.5MHz
2.FM DAA
97.9MHz
0dBuV 0%
Adjustment NG or No Signal
dBuV 0%
High or Low or No Signal
dBuV 0%
High or Low or No Signal
dBuV 0%
Adjustment NG or No Signal
40dBuV 0%
40dBuV 0%
POWER
POWER OFF
(ADJUSTMENT MODE FINISH)
No Signal
No Signal
3.FM DAA
108.0MHz
4.FM S.MATER
97.9MHz
5.FM S.MATER
97.9MHz 7
6.FM FULL SEPARATION
97.9MHz 7
Lch 40MHzmod 1kHz
7.FM IF COUNTER
97.9MHz 7
8.AM S.METER
999kHz 26
9.AM S.METER
999kHz 56
10.AM IF COUNTER
999kHz 56
40dBuV 0%
40dBuV 0%
0dBuV 0%
0dBuV 0%
0dBuV 0%
dBuV 0%
dBuV 0%
dBuV 0%
Press OK
Press OK
Press OK
Press OK
Press OK
Press OK
Press OK
Press OK
3.FM DAA
108.0MHz
4.FM S.MATER
97.9MHz
5.FM S.MATER
97.9MHz 7
6.FM FULL SEPARATION
97.9MHz 7
7.FM COUNTER
97.9MHz 7
8.AM S.METER
999kHz 26
9.AM S.METER
999kHz 56
10.AM IF COUNTER
999kHz 56
40dBuV 0%
40dBuV 0%
High or Low or No Signal
0dBuV 0%
High or Low or No Signal
0dBuV 0%
Adjustment NG or No Signal
0dBuV 0%
Adjustment NG or No Signal
dBuV 0%
High or Low or No Signal
dBuV 0%
High or Low or No Signal
dBuV 0%
Adjustment NG or No Signal
No Signal
MANUAL ADJUSTMENT
COMPLETED
POWER
POWER OFF
(ADJUSTMENT MODE FINISH)
(No.MA192)1-27
4.2.2 Error code of front panel mechanism
PANEL ANGLE
1
2
3
4
OPEN
PANEL
CLOSE
10 degrees
20 degrees
30 degrees
OPEN
Details
OPEN error
1.Time out error by OPEN position cannot detect.
CLOSE error (ANGLE 1 error)
1.Time out error by ANGLE 1 position cannot detect.
Angle positioning error
Moving to 10 degrees (ANGLE 2 error)
1.Time out error by ANGLE 2 position cannot detect at moving to open position.
2. Missing to ANGLE 1 and detected ANGLE 2 position at moving to open position.
3.Time out error by ANGLE 2 cannot detect at moving to close position.
MAIN BODY
ERROR CODE
(SERVICE MODE)
0A01
0B06
0D21
0D22
0D23
ERROR CODE
(NORMAL)
ERR
01
06
21
22
23
Moving to 20 degrees (ANGLE 3 error)
1.Time out error by ANGLE 3 position cannot detect at moving to open position.
2. Missing to ANGLE 2 and detected ANGLE 3 position at moving to open position.
3.Time out error by ANGLE 3 cannot detect at moving to close position.
Moving to 30 degrees (ANGLE 4 error)
1.Time out error by ANGLE 4 position cannot detect at moving to open position.
2. Missing to ANGLE 3 and detected ANGLE 4 position at moving to open position.
3.Time out error by ANGLE 4 cannot detect at moving to close position.
Abnormal switch position at moving panel
The panel move to open and close potisiton,detected abnormal switch position.
0E31
0E32
0E33
0F41
0F42
0F43
31
32
33
41
42
43
0A0000
1-28 (No.MA192)
5.1Feed section
SECTION 5
TROUBLESHOOTING
Is 2V at IC601 pin 63?
YES
Is 4V present at both
sides of the feed motor?
YES
Check the feed motor.
5.2Focus section
5.3Spindle section
NO
Is the wiring for IC601
pin 63 correct?
NO
Is 2V present at IC681
pins 1 and 27?
Check IC681.
When the lens is
moving:
Does the S-search
waveform appear at
IC681 pins 10 and 11?
NO
NO
YES
4V
YES
YES
Is 8V present at IC681
pins 3 and 12?
Check the vicinity of
IC601.
Check the feed motor
connection wiring.
NO
Check the circuits in
the vicinity of IC681
pins 13 and 14.
Check the pickup and
its connections.
NO
Check CD8V.
YES
YES
Is the disk rotated?
YES
Does the RF signal
appear at IC601 pin 26?
YES
Is the RF waveform
at IC601 pin 26 distorted?
YES
Proceed to the Tracking
section
5.4Tracking section
When the disc is rotated
at first:
Is the tracking error
signal output at IC601
pin 57?
NO
Is 4V present between
IC681 pins 6 and 7?
Check the spindle motor
and its wiring.
NO
Check the circuits in
the vicinity of IC601
or the pickup.
NO
NO
Approx. 1.2V
YES
NO
YES
Check the circuits in
the vicinity of IC601
pins 48 and 49 .
Is 4V present at IC601
pin 64?
YES
Check the vicinity of
IC681.
NO
Check the pickup and
its connections.
NO
Check IC601.
Check IC601.
(No.MA192)1-29
5.5Signal processing section
Is the sound output from
both channels (L, R)?
YES
Normal
NO
No sound from either
channel.
Is 9V present at IC165
/IC265 pin 16?
Is 5V present at IC365
pina 2, 3, 9 and 10?
Is 7V present at IC951
pina 3, 5, 7, 9, 17, 19
21 and 23?
YES
YES
YES
YES
Compare the L-ch and
NO
R-ch to locate the
defective point.
NO
Is 9V present at IC901
pin 10?
Check the connection
between IC901 pin10
and IC165/IC265 pin
16.
NO
Check the vicinity of
IC365.
NO
Check the power amp.
IC951.
YES
NO
Check IC901 and its
peripheral circuits.
Check the speaker
connector and its
connection.
1-30 (No.MA192)
5.6Maintenance of laser pickup
(1) Cleaning the pick up lens
Before you replace the pick up, please try to clean the lens
with a alcohol soaked cotton swab.
(2) Life of the laser diode
When the life of the laser diode has expired, the following
symptoms will appear.
• The level of RF output (EFM output: amplitude of eye
pattern) will be low.
5.7Replacement of laser pickup
Turn of the power switch and, disconnect the
power cord.
Replace the pickup with a normal one. (Refer
to "Removing the pickup unit" on the previous page.)
Is RF output
1.3 0.4Vp-p?
NO
Replace it.
YES
OK
(3) Semi-fixed resistor on the APC PC board
The semi-fixed resistor on the APC printed circuit board
which is attached to the pickup is used to adjust the laser
power.Since this adjustment should be performed to match
the characteristics of the whole optical block, do not touch
the semi-fixed resistor.
If the laser power is lower than the specified value, the laser diode is almost worn out, and the laser pickup should
be replaced. If the semi-fixed resistor is adjusted while the
pickup is functioning normally, the laser pickup may be
damaged due to excessive current.
Plug the power cord in, and turn the power on.
At this time, check that the laser emits for about
seconds and the objective lens moves up and down.
Note: Do not observe the laser beam directly.
Play a disc.
Check the eye-pattern at
RF test point.
Finish.
(No.MA192)1-31
5.816 PIN CORD DIAGRAM
GN
GN/BK
VI/BK
VI
NC
BL/WH
RD
BK
WH/BK
GY/BK
OR/WH
RR+
RR-
FR-
FL+
FL-
RL+
WH
GY
BR
NC
YL
VI/BK
VI
GYFR+
GY/BK
WH/BK
WH
GN
BK
RD
BL
Black
Red
Blue
WHWhite
BR
Brown
BR
BL/WH
RD
YL
OR/WH
GN
VI
GY
YL
OR
Green
Violet
Gray
Yellow
Orange
ACC
MEMORY
ILL
TEL
REMOTE
VI/BK
VI
GY/BK
GY
WH
WH/BK
GN/BK
GN
RR
FR
FL
RL
REMOTE
RL-
Rear Right
Front Right
Front Left
Rear Left
Remote out
GN/BK
BK
ANT
ACC
TEL
GND
MEMORY
GND
Auto Antenna
ACC Line
Telephone Muting
Ground
Memory Backup Battery +
NC
NC
BL/WH
RD
BR
YL
OR/WH
BK
1-32 (No.MA192)
ILL
Illuminations Control
(No.MA192)1-33
Victor Company of Japan, Limited
AV & MULTIMEDIA COMPANY CAR ELECTRONICS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan
(No.MA192)
Printed in Japan
VPT
PARTS LIST
[ KD-SHX851 ]
* All printed circuit boards and its assemblies are not available as service parts.
Area suffix
E ------------- Southern Europe
EX ------------ Northern Europe
EY ------------- Eastern Europe
EU ------------------------- Turkey
MA192
- Contents -
Exploded view of general assembly and parts list (Block No.M1)
CD mechanism assembly and parts list (Block No.MB)
Electrical parts list (Block No.01~03)
Packing materials and accessories parts list (Block No.M3)
3- 2
3- 6
3-10
3-22
3-1
Exploded view of general assembly and parts list
8
Block No.
M
M
1
M
43
45
44
43
24
32
100
30
31
A
M
40
25
C
28
84
101
M
26
E
49
20
Main board
B
D
22
32
A
88
38
a
21
14
46
17
6
46
F
F'
13
12
11
65
66
52
67
54
56
68
55
53
57
62
60
59
64
63
Switch board
75
73
61
51
58
58
69
70
87
71
19
74
48
72
33
71
15
1
G
G'
3-2
50
47
90
85
92
B
96
85
91
8
85
93
38
89
35
4
98
J
16
F
99
H
94
95
47
J
97
3
2
36
b
29
c
86
G
1
b
34
H
39
23
D
42
E
41
c
39
C
9
17
2
11
a
16
F'
8
7
37
G'
15
83
27
18
G
G'
10
34
5
83
82
81
HIDEAWAY
76
77
79
78
80
3-3
General Assembly
Block No. [M][1][M][M]
Symbol No.Part No.Part NameDescriptionLocal
1GE20156-001AGEAR BKT UNIT
2LV40847-002ASPACER
3FSYH4036-100SHEET
4GE30968-002ALEVER BKT UNIT
5GE30964-003ALOWER LEVER ASS
6LV35330-002AFRONT BKT ASSY
7QNZ0664-003CAR CONNECTOR
8QAL0587-001FPC
9FSYH4036-100SHEET
10LV35484-001ADETACH LEVER
11GE30973-001AKICK LEVER
12GE40192-002ASHAFT
13GE40193-002ASHAFT
14LV35381-001ASD GUIDE
15QYWDL123525SLIT WASHER3.5mm/1.2mm x 0.25mm(x2)
16QYWDL215025SLIT WASHER5mm/2.1mm x 0.25mm(x2)
17GE40194-001AT SPRING
18GE40195-002AT SPRING
19GE40218-009ASHEET(x2)
20LV11025-001ATOP CHASSIS
21GE40259-001AMECHA HEAT SINK
22LV43854-003ACOOLING RUBBER
23GE10074-001ABOTTOM CHASSIS
24GE31642-001AF CHASSIS ASSY
25GE40156-001ABLIND
26LV35751-001AEARTH SPRING
27GE30974-001AFPC GUIDE
28GE40196-002AABSORBER(x2)
29GE31204-002AINSULATOR
30LV35644-005ASIDE HEAT SINK
31LV44394-001ACOOLING SHEET
32QYSPSP2003MASCREWM2 x 3mm(x2)
33QYSPSGU2040MATAP SCREWM2 x 4mm(x2)
34LV42181-002ASPECIAL SCREW(x2)
35LV40865-002AMINI SCREW(x2)
36LV40865-002AMINI SCREW(x3)
37LV40865-002AMINI SCREW
38LV41200-004ASPECIAL SCREW(x2)
39GE40235-001ASCREW(x2)
40QYSDST2604ZATAP SCREWM2.6 x 4mm
41LV41200-004ASPECIAL SCREW
42LV41200-004ASPECIAL SCREW(x2)
43GE40235-001ASCREW(x2)
44LV41200-007ASPECIAL SCREW(x2)
45LV41200-005ASPECIAL SCREW
46QYSDST2605ZATAP SCREWM2.6 x 5mm(x3)
47QYSDST2604ZATAP SCREWM2.6 x 4mm(x3)
48VKZ4777-009MINI SCREW(x2)
49QYSDST2604ZATAP SCREWM2.6 x 4mm
50QQR0491-001FERRITE CORETDK (GRAY)
51LV35694-002AFRONT PANEL ASSY
52LV35636-002AFINDER(L)
53LV35637-005AFINDER(R)
54LV35517-007ABUTTON EJECT
55LV35522-001AEJECT BASE
56LV35518-004APOWER BUTTON
57LV35523-001APOWER BASE
58LV35508-001ASOURCE WALL(x2)
59LV35640-002A3 BUTTON
60LV35641-001A4 BUTTON(A)
61LV35642-001A4 BUTTON(B)
62LV35516-004ADETACH BUTTON
63LV44055-001ACOMPRESSION SPRING
64LV35541-002ARESET BUTTON
65LV35547-001AVOL.KNOB ASSY
66LV35545-001AVOL. RUBBER
67LV35515-003AKNOB RING
68LV40848-056ASPACER(P)(x2)
69LV11024-001AREAR COVER
70LV35643-001AEARTH PLATE
71VKZ4777-006MINI SCREW(x6)
72QYSPSPU1730MASCREWM1.7 x 3mm
73QLE0042-001OEL MODULESHX851E,SHX851EU,SHX851EX
73QLE0038-001OEL MODULESHX851EY
C1NCB31HK-222XC CAPACITOR2200pF 50V K
C2NBE21CM-106XTA E CAPACITOR10uF 16V M
C3NDC31HJ-391XC CAPACITOR390pF 50V J
C4NBE21CM-106XTA E CAPACITOR10uF 16V M
C5NDC31HJ-391XC CAPACITOR390pF 50V J
C7NDC31HJ-391XC CAPACITOR390pF 50V J
C13NDC31HJ-391XC CAPACITOR390pF 50V J
C21NCB31HK-102XC CAPACITOR1000pF 50V K
C22NCB31HK-102XC CAPACITOR1000pF 50V K
Part No.Part NameDescriptionLocal
3-10
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
Part No.Part NameDescriptionLocal
C28NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C29NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C31NDC31HJ-221XC CAPACITOR220pF 50V J
C32NDC31HJ-5R0XC CAPACITOR5pF 50V J
C33NDC31HJ-5R0XC CAPACITOR5pF 50V J
C34NBE20JM-475XTA E CAPACITOR4.7uF 6.3V M
C35NCB31CK-104XC CAPACITOR0.1uF 16V K
C36NDC31HJ-181XC CAPACITOR180pF 50V J
C37NCB31HK-103XC CAPACITOR0.01uF 50V K
C40NDC31HJ-101XC CAPACITOR100pF 50V J
C41NCB31CK-104XC CAPACITOR0.1uF 16V K
C42NCB31CK-104XC CAPACITOR0.1uF 16V K
C43NCB31CK-104XC CAPACITOR0.1uF 16V K
C44NBE20JM-475XTA E CAPACITOR4.7uF 6.3V M
C45NBE20JM-475XTA E CAPACITOR4.7uF 6.3V M
C46NCB31CK-104XC CAPACITOR0.1uF 16V K
C47NBE20JM-475XTA E CAPACITOR4.7uF 6.3V M
C48NEAF0JM-107XE CAPACITOR100uF 6.3V M
C50NBE20JM-226XTA E CAPACITOR22uF 6.3V M
C51NCB31CK-473XC CAPACITOR0.047uF 16V K
C53NCB31CK-105XC CAPACITOR1uF 16V K
C54NBE20JM-226XTA E CAPACITOR22uF 6.3V M
C55NCB31CK-104XC CAPACITOR0.1uF 16V K
C56NDC31HJ-101XC CAPACITOR100pF 50V J
C57NDC31HJ-101XC CAPACITOR100pF 50V J
C59NCB31CK-333XC CAPACITOR0.033uF 16V K
C60NCB31CK-104XC CAPACITOR0.1uF 16V K
C61NEAF0JM-107XE CAPACITOR100uF 6.3V M
C62NEAF0JM-227XE CAPACITOR220uF 6.3V M
C63NCB31EK-223XC CAPACITOR0.022uF 25V K
C64NCB31CK-105XC CAPACITOR1uF 16V K
C65NCB31HK-471XC CAPACITOR470pF 50V K
C66NDC31HJ-101XC CAPACITOR100pF 50V J
C67NDC31HJ-101XC CAPACITOR100pF 50V J
C68NDC31HJ-101XC CAPACITOR100pF 50V J
C69NDC31HJ-221XC CAPACITOR220pF 50V J
C70NDC31HJ-101XC CAPACITOR100pF 50V J
C71NDC31HJ-101XC CAPACITOR100pF 50V J
C76NCB31EK-223XC CAPACITOR0.022uF 25V K
C77NCB31HK-103XC CAPACITOR0.01uF 50V K
C78NCB31HK-103XC CAPACITOR0.01uF 50V K
C79NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C80NCB31EK-223XC CAPACITOR0.022uF 25V K
C81NDC31HJ-221XC CAPACITOR220pF 50V J
C82NCB31EK-223XC CAPACITOR0.022uF 25V K
C85NCB31CK-104XC CAPACITOR0.1uF 16V K
C86NCB31CK-104XC CAPACITOR0.1uF 16V K
C87NCB31CK-104XC CAPACITOR0.1uF 16V K
C88NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C89NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C90NCB31CK-104XC CAPACITOR0.1uF 16V K
C91NCB31CK-104XC CAPACITOR0.1uF 16V K
C92NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C99NCB31HK-332XC CAPACITOR3300pF 50V K
C101NCB31CK-104XC CAPACITOR0.1uF 16V K
C102NCB31CK-473XC CAPACITOR0.047uF 16V K
C105NDC31HJ-471XC CAPACITOR470pF 50V J
C106NDC31HJ-101XC CAPACITOR100pF 50V J
C108NCB31CK-104XC CAPACITOR0.1uF 16V K
C131NCB31HK-102XC CAPACITOR1000pF 50V K
C132NDC31HJ-391XC CAPACITOR390pF 50V J
C133NDC31HJ-391XC CAPACITOR390pF 50V J
C134NDC31HJ-101XC CAPACITOR100pF 50V J
C137NBE41AM-476XTA E CAPACITOR47uF 10V M
C140NBE41CM-226XTA E CAPACITOR22uF 16V M
C141NCB31HK-102XC CAPACITOR1000pF 50V K
C142NDC31HJ-391XC CAPACITOR390pF 50V J
C143NDC31HJ-391XC CAPACITOR390pF 50V J
C144NDC31HJ-101XC CAPACITOR100pF 50V J
C147NBE41AM-476XTA E CAPACITOR47uF 10V M
C150NEB21CM-226XE CAPACITOR22uF 16V M
C151NEB21CM-226XE CAPACITOR22uF 16V M
C152NEAF1AM-107XE CAPACITOR100uF 10V M
C153NCB31HK-152XC CAPACITOR1500pF 50V K
C154NEB21HM-225XE CAPACITOR2.2uF 50V M
C156NCB31CK-104XC CAPACITOR0.1uF 16V K
C158NBE41AM-476XTA E CAPACITOR47uF 10V M
C160NEB21CM-226XE CAPACITOR22uF 16V M
C161NEB21CM-226XE CAPACITOR22uF 16V M
C162NEAF1AM-107XE CAPACITOR100uF 10V M
C163NCB31HK-152XC CAPACITOR1500pF 50V K
C164NEB21HM-225XE CAPACITOR2.2uF 50V M
C166NCB31CK-104XC CAPACITOR0.1uF 16V K
C182NCB31EK-223XC CAPACITOR0.022uF 25V K
C186NCB31EK-223XC CAPACITOR0.022uF 25V K
C191NBE21CM-106XTA E CAPACITOR10uF 16V M
C192NEB21HM-105XE CAPACITOR1uF 50V M
C193NEB21HM-105XE CAPACITOR1uF 50V M
C194NEAF1CM-106XE CAPACITOR10uF 16V M
C195NCB31CK-104XC CAPACITOR0.1uF 16V K
C201NCB31CK-104XC CAPACITOR0.1uF 16V K
C202NCB31CK-473XC CAPACITOR0.047uF 16V K
C203NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C205NDC31HJ-471XC CAPACITOR470pF 50V J
C206NDC31HJ-101XC CAPACITOR100pF 50V J
C207NBE41AM-476XTA E CAPACITOR47uF 10V M
C208NCB31CK-104XC CAPACITOR0.1uF 16V K
C209NBE21AM-106XTA E CAPACITOR10uF 10V M
C231NCB31HK-102XC CAPACITOR1000pF 50V K
C232NDC31HJ-391XC CAPACITOR390pF 50V J
C233NDC31HJ-391XC CAPACITOR390pF 50V J
C234NDC31HJ-101XC CAPACITOR100pF 50V J
C237NBE41AM-476XTA E CAPACITOR47uF 10V M
C240NBE41CM-226XTA E CAPACITOR22uF 16V M
C241NCB31HK-102XC CAPACITOR1000pF 50V K
C242NDC31HJ-391XC CAPACITOR390pF 50V J
C243NDC31HJ-391XC CAPACITOR390pF 50V J
C244NDC31HJ-101XC CAPACITOR100pF 50V J
C247NBE41AM-476XTA E CAPACITOR47uF 10V M
C250NEB21CM-226XE CAPACITOR22uF 16V M
C251NEB21CM-226XE CAPACITOR22uF 16V M
C252NEAF1AM-107XE CAPACITOR100uF 10V M
C253NCB31HK-152XC CAPACITOR1500pF 50V K
C254NEB21HM-225XE CAPACITOR2.2uF 50V M
C256NCB31CK-104XC CAPACITOR0.1uF 16V K
C258NBE41AM-476XTA E CAPACITOR47uF 10V M
C260NEB21CM-226XE CAPACITOR22uF 16V M
C261NEB21CM-226XE CAPACITOR22uF 16V M
C262NEAF1AM-107XE CAPACITOR100uF 10V M
C263NCB31HK-152XC CAPACITOR1500pF 50V K
C264NEB21HM-225XE CAPACITOR2.2uF 50V M
C266NCB31CK-104XC CAPACITOR0.1uF 16V K
C282NCB31EK-223XC CAPACITOR0.022uF 25V K
C286NCB31EK-223XC CAPACITOR0.022uF 25V K
C291NBE21CM-106XTA E CAPACITOR10uF 16V M
C292NEB21HM-105XE CAPACITOR1uF 50V M
C293NEB21HM-105XE CAPACITOR1uF 50V M
C294NEAF1CM-106XE CAPACITOR10uF 16V M
C295NCB31CK-104XC CAPACITOR0.1uF 16V K
C301NCB31CK-104XC CAPACITOR0.1uF 16V K
C302NCB31CK-104XC CAPACITOR0.1uF 16V K
C308NCB31CK-104XC CAPACITOR0.1uF 16V K
C311NCB31CK-104XC CAPACITOR0.1uF 16V K
C312NBE20JM-476XTA E CAPACITOR47uF 6.3V M
C313NCB31CK-104XC CAPACITOR0.1uF 16V K
C314NBE20JM-476XTA E CAPACITOR47uF 6.3V M
C315NCB31CK-104XC CAPACITOR0.1uF 16V K
C316NCS31HJ-102XC CAPACITOR1000pF 50V J
C317NCB31CK-104XC CAPACITOR0.1uF 16V K
C318NBE20JM-476XTA E CAPACITOR47uF 6.3V M
C321NCB31CK-104XC CAPACITOR0.1uF 16V K
C322NCB31CK-104XC CAPACITOR0.1uF 16V K
C323NCB31CK-104XC CAPACITOR0.1uF 16V K
C331NCB31CK-104XC CAPACITOR0.1uF 16V K
C332NCB31CK-104XC CAPACITOR0.1uF 16V K
C344NDC31HJ-120XC CAPACITOR12pF 50V J
C345NDC31HJ-100XC CAPACITOR10pF 50V J
C346NBE20JM-476XTA E CAPACITOR47uF 6.3V M
C347NCB31CK-104XC CAPACITOR0.1uF 16V K
C701QEZ0361-229C.CAPA0.022F
C702NCB31HK-103XC CAPACITOR0.01uF 50V K
C703NCB31HK-103XC CAPACITOR0.01uF 50V K
C704NCB31HK-103XC CAPACITOR0.01uF 50V K
C705NCB31HK-103XC CAPACITOR0.01uF 50V K
C707NCB31HK-103XC CAPACITOR0.01uF 50V K
C709NCB31HK-103XC CAPACITOR0.01uF 50V K
3-11
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
Part No.Part NameDescriptionLocal
C710NCB31HK-103XC CAPACITOR0.01uF 50V K
C713NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C715NCB31HK-471XC CAPACITOR470pF 50V K
C716NCB31HK-103XC CAPACITOR0.01uF 50V K
C717NEAF0JM-227XE CAPACITOR220uF 6.3V M
C718NEAF0JM-227XE CAPACITOR220uF 6.3V M
C719NEAF0JM-227XE CAPACITOR220uF 6.3V M
C720NCB31HK-103XC CAPACITOR0.01uF 50V K
C724NCB31CK-473XC CAPACITOR0.047uF 16V K
C726NCB31HK-103XC CAPACITOR0.01uF 50V K
C791NEAF0JM-227XE CAPACITOR220uF 6.3V M
C900NCB31HK-471XC CAPACITOR470pF 50V K
C901QEZ0723-338E CAPACITOR3300uF
C902NEAF1CM-226XE CAPACITOR22uF 16V M
C903NEAF1CM-226XE CAPACITOR22uF 16V M
C904NCB31HK-103XC CAPACITOR0.01uF 50V K
C905NEAF1AM-107XE CAPACITOR100uF 10V M
C906NCB31CK-104XC CAPACITOR0.1uF 16V K
C907NBE21AM-106XTA E CAPACITOR10uF 10V M
C908NEAF1AM-107XE CAPACITOR100uF 10V M
C910NEAF1CM-106XE CAPACITOR10uF 16V M
C911NCB31CK-104XC CAPACITOR0.1uF 16V K
C912NEAF1HM-225XE CAPACITOR2.2uF 50V M
C917NCB31HK-103XC CAPACITOR0.01uF 50V K
C921NEAF1CM-107XE CAPACITOR100uF 16V M
C922NCB31CK-104XC CAPACITOR0.1uF 16V K
C923NEHN1EM-476XE CAPACITOR47uF 25V M
C924NCB31EK-104XC CAPACITOR0.1uF 25V K
C925NEHN1EM-476XE CAPACITOR47uF 25V M
C941NEAF1CM-107XE CAPACITOR100uF 16V M
C942NEAF0JM-107XE CAPACITOR100uF 6.3V M
C950NCB31CK-104XC CAPACITOR0.1uF 16V K
C951NEAF1CM-107XE CAPACITOR100uF 16V M
C952NEAF0JM-227XE CAPACITOR220uF 6.3V M
C959NCB31HK-331XC CAPACITOR330pF 50V K
C960NEHN1EM-477XE CAPACITOR470uF 25V M
C961NCJ11EK-106X-RC CAPA
C962NEAF0JM-227XE CAPACITOR220uF 6.3V M
C964NCJ11EK-106X-RC CAPA
C965NCB31CK-104XC CAPACITOR0.1uF 16V K
C966NBE21AM-475XTA E CAPACITOR4.7uF 10V M
C967NCB31CK-104XC CAPACITOR0.1uF 16V K
C968NCB31HK-331XC CAPACITOR330pF 50V K
C969NCB31HK-331XC CAPACITOR330pF 50V K
C970NBZ0020-107XE CAPACITOR100uF
C971NCB31CK-104XC CAPACITOR0.1uF 16V K
C972NCB31HK-104XC CAPACITOR0.1uF 50V K
C973NCB31HK-104XC CAPACITOR0.1uF 50V K
C974NCJ11EK-106X-RC CAPA
C975NDC31HJ-101XC CAPACITOR100pF 50V J
C1401NEAF1HM-225XE CAPACITOR2.2uF 50V M
C1402NCB31HK-472XC CAPACITOR4700pF 50V K
C1403NDC31HJ-101XC CAPACITOR100pF 50V J
C1404NCB31CK-102XC CAPACITOR1000pF 16V K
C1451NDC31HJ-101XC CAPACITOR100pF 50V J
C1452NDC31HJ-101XC CAPACITOR100pF 50V J
C1501NDC31HJ-101XC CAPACITOR100pF 50V J
C1502NEAF1HM-105XE CAPACITOR1uF 50V M
C1801NCB31CK-104XC CAPACITOR0.1uF 16V K
C2401NEAF1HM-225XE CAPACITOR2.2uF 50V M
C2402NCB31HK-472XC CAPACITOR4700pF 50V K
C2403NDC31HJ-101XC CAPACITOR100pF 50V J
C2404NCB31CK-102XC CAPACITOR1000pF 16V K
C2451NDC31HJ-101XC CAPACITOR100pF 50V J
C2452NDC31HJ-101XC CAPACITOR100pF 50V J
C2501NDC31HJ-101XC CAPACITOR100pF 50V J
C2502NEAF1HM-105XE CAPACITOR1uF 50V M
C2801NCB31CK-224XC CAPACITOR0.22uF 16V K
C3111NCB31CK-105XC CAPACITOR1uF 16V K
C3112NCB31CK-473XC CAPACITOR0.047uF 16V K
C3114NCB31CK-473XC CAPACITOR0.047uF 16V K
C3401NEAF0JM-476XE CAPACITOR47uF 6.3V M
C3403NCB31CK-473XC CAPACITOR0.047uF 16V K
C3405NCB31HK-222XC CAPACITOR2200pF 50V K
C3451NCB31CK-473XC CAPACITOR0.047uF 16V K
C3452NDC31HJ-101XC CAPACITOR100pF 50V J
C3803NEAF1EM-475XE CAPACITOR4.7uF 25V M
C3805NBE41AM-476XTA E CAPACITOR47uF 10V M
C3806NCB31HK-222XC CAPACITOR2200pF 50V K
C3808NCB31CK-104XC CAPACITOR0.1uF 16V K
C3809NCB31CK-333XC CAPACITOR0.033uF 16V K
C3810NCB31CK-473XC CAPACITOR0.047uF 16V K
C3811NCB31HK-103XC CAPACITOR0.01uF 50V K
C3813NCB31CK-104XC CAPACITOR0.1uF 16V K
C3814NBE41CM-226XTA E CAPACITOR22uF 16V M
C3815NEAF1EM-475XE CAPACITOR4.7uF 25V M
C3816NCB31HK-152XC CAPACITOR1500pF 50V K
C3817NEAF1AM-107XE CAPACITOR100uF 10V M
C3818NEAF1CM-226XE CAPACITOR22uF 16V M
C5001NCB31EK-104XC CAPACITOR0.1uF 25V K
C5002NCB31EK-104XC CAPACITOR0.1uF 25V K
C5003NCB31EK-104XC CAPACITOR0.1uF 25V K
C5004NCB31EK-104XC CAPACITOR0.1uF 25V K
C5005NCB31EK-104XC CAPACITOR0.1uF 25V K
C5006QEHP1EM-338E CAPACITOR3300uF 25V M
C5007QEHP1EM-338E CAPACITOR3300uF 25V M
C5008NCB31EK-104XC CAPACITOR0.1uF 25V K
C5009NCB31EK-104XC CAPACITOR0.1uF 25V K
C5010NEAF1HM-335XE CAPACITOR3.3uF 50V M
C5011NCB31EK-104XC CAPACITOR0.1uF 25V K
C7001NDC31HJ-330XC CAPACITOR33pF 50V J
C7002NDC31HJ-330XC CAPACITOR33pF 50V J
C7004NDC31HJ-180XC CAPACITOR18pF 50V J
C7005NDC31HJ-180XC CAPACITOR18pF 50V J
C7020NEAF1HM-104XE CAPACITOR0.1uF 50V M
C7101NCB31HK-103XC CAPACITOR0.01uF 50V K
C7116NDC31HJ-101XC CAPACITOR100pF 50V J
C7117NDC31HJ-101XC CAPACITOR100pF 50V J
C7200NCB31HK-471XC CAPACITOR470pF 50V K
C7201NCB31HK-103XC CAPACITOR0.01uF 50V K
C7202NCB31HK-103XC CAPACITOR0.01uF 50V K
C7203NCB31HK-103XC CAPACITOR0.01uF 50V K
C7204NCB31HK-103XC CAPACITOR0.01uF 50V K
C7205NCB31CK-104XC CAPACITOR0.1uF 16V K
C7300NCB31CK-473XC CAPACITOR0.047uF 16V K
C7301NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C7400NBE20JM-476XTA E CAPACITOR47uF 6.3V M
C7401NCB31HK-103XC CAPACITOR0.01uF 50V K
C9070NEAF1AM-107XE CAPACITOR100uF 10V M
C9071NCJ11EK-106X-RC CAPA
C9072NEAF1CM-476XE CAPACITOR47uF 16V M
C9073NCJ11EK-106X-RC CAPA
C9074NCB31CK-104XC CAPACITOR0.1uF 16V K
C9075NCB31HK-472XC CAPACITOR4700pF 50V K
C9076NCB31HK-103XC CAPACITOR0.01uF 50V K
C9077NBE20JM-476XTA E CAPACITOR47uF 6.3V M
C9078NCB31CK-104XC CAPACITOR0.1uF 16V K
C9081NCJ11EK-106X-RC CAPA
C9083NEAF1CM-107XE CAPACITOR100uF 16V M
C9084NCB31HK-103XC CAPACITOR0.01uF 50V K
C9085NBE20JM-476XTA E CAPACITOR47uF 6.3V M
C9088NCB31HK-103XC CAPACITOR0.01uF 50V K
C9089NBE20JM-476XTA E CAPACITOR47uF 6.3V M
C9091NEAF1AM-107XE CAPACITOR100uF 10V M
C9092NCB31CK-473XC CAPACITOR0.047uF 16V K
C9094NCB31CK-473XC CAPACITOR0.047uF 16V K
C9101NEAF1CM-106XE CAPACITOR10uF 16V M
C9151NCB31CK-104XC CAPACITOR0.1uF 16V K
C9202NCB31CK-104XC CAPACITOR0.1uF 16V K
C9501NEAF1EM-475XE CAPACITOR4.7uF 25V M
C9502NCB31HK-222XC CAPACITOR2200pF 50V K
C9503NDC31HJ-101XC CAPACITOR100pF 50V J
C9505NEAF1AM-107XE CAPACITOR100uF 10V M
C9506NCB31HK-222XC CAPACITOR2200pF 50V K
C9507NCB31HK-222XC CAPACITOR2200pF 50V K
C9509NCB31HK-471XC CAPACITOR470pF 50V K
C9510NCB31HK-272XC CAPACITOR2700pF 50V K
C9511NEAF1EM-475XE CAPACITOR4.7uF 25V M
C9515NCB31HK-103XC CAPACITOR0.01uF 50V K
C9516NCB31CK-105XC CAPACITOR1uF 16V K
C9517NDC31HJ-121XC CAPACITOR120pF 50V J
C9519NCB31CK-105XC CAPACITOR1uF 16V K
C9531NEAF1CM-226XE CAPACITOR22uF 16V M
C9532NCB31HK-332XC CAPACITOR3300pF 50V K
C9533NCS31HJ-271XC CAPACITOR270pF 50V J
C9534NCS31HJ-271XC CAPACITOR270pF 50V J
3-12
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
Part No.Part NameDescriptionLocal
C9535NFVB1EJ-224XMF CAPACITOR0.22uF 25V J
C9536NFVB1EJ-224XMF CAPACITOR0.22uF 25V J
C9538NCJ11EK-106X-RC CAPA
C9539NCB31CK-104XC CAPACITOR0.1uF 16V K
C9540NCB31CK-104XC CAPACITOR0.1uF 16V K
C9542NCB31HK-103XC CAPACITOR0.01uF 50V K
C9543NBE21CM-106XTA E CAPACITOR10uF 16V M
C9544NCB31HK-103XC CAPACITOR0.01uF 50V K
C9545NCB11HK-224XC CAPACITOR0.22uF 50V K
C9551NEAF1EM-475XE CAPACITOR4.7uF 25V M
C9552NCB31HK-222XC CAPACITOR2200pF 50V K
C9553NDC31HJ-101XC CAPACITOR100pF 50V J
C9555NEAF1AM-107XE CAPACITOR100uF 10V M
C9556NCB31HK-222XC CAPACITOR2200pF 50V K
C9557NCB31HK-222XC CAPACITOR2200pF 50V K
C9559NCB31HK-471XC CAPACITOR470pF 50V K
C9560NCB31HK-272XC CAPACITOR2700pF 50V K
C9561NEAF1EM-475XE CAPACITOR4.7uF 25V M
C9563NCS31HJ-271XC CAPACITOR270pF 50V J
C9564NCS31HJ-271XC CAPACITOR270pF 50V J
C9565NCB31HK-103XC CAPACITOR0.01uF 50V K
C9566NCB31CK-105XC CAPACITOR1uF 16V K
C9567NDC31HJ-121XC CAPACITOR120pF 50V J
C9568NCB31HK-332XC CAPACITOR3300pF 50V K
C9569NCB31CK-105XC CAPACITOR1uF 16V K
C9581NEAF1CM-226XE CAPACITOR22uF 16V M
C9583NCB31HK-222XC CAPACITOR2200pF 50V K
C9584NCB31HK-222XC CAPACITOR2200pF 50V K
C9585NFVB1EJ-224XMF CAPACITOR0.22uF 25V J
C9586NFVB1EJ-224XMF CAPACITOR0.22uF 25V J
C9587NCB11HK-224XC CAPACITOR0.22uF 50V K
C9588NCJ11EK-106X-RC CAPA
C9589NCB31CK-104XC CAPACITOR0.1uF 16V K
C9590NCB31CK-104XC CAPACITOR0.1uF 16V K
C9593NCB31HK-222XC CAPACITOR2200pF 50V K
C9594NCB31HK-222XC CAPACITOR2200pF 50V K
C9595NCB11HK-224XC CAPACITOR0.22uF 50V K
C9597NCB11HK-224XC CAPACITOR0.22uF 50V K
C9601NEAF1EM-475XE CAPACITOR4.7uF 25V M
C9602NCB31HK-222XC CAPACITOR2200pF 50V K
C9603NDC31HJ-101XC CAPACITOR100pF 50V J
C9605NEAF1AM-107XE CAPACITOR100uF 10V M
C9606NCB31HK-222XC CAPACITOR2200pF 50V K
C9607NCB31HK-222XC CAPACITOR2200pF 50V K
C9609NCB31HK-471XC CAPACITOR470pF 50V K
C9610NCB31HK-272XC CAPACITOR2700pF 50V K
C9611NEAF1EM-475XE CAPACITOR4.7uF 25V M
C9615NCB31HK-103XC CAPACITOR0.01uF 50V K
C9616NCB31CK-105XC CAPACITOR1uF 16V K
C9617NDC31HJ-121XC CAPACITOR120pF 50V J
C9619NCB31CK-105XC CAPACITOR1uF 16V K
C9631NEAF1CM-226XE CAPACITOR22uF 16V M
C9632NCB31HK-332XC CAPACITOR3300pF 50V K
C9633NCS31HJ-271XC CAPACITOR270pF 50V J
C9634NCS31HJ-271XC CAPACITOR270pF 50V J
C9635NFVB1EJ-224XMF CAPACITOR0.22uF 25V J
C9636NFVB1EJ-224XMF CAPACITOR0.22uF 25V J
C9638NCJ11EK-106X-RC CAPA
C9639NCB31CK-104XC CAPACITOR0.1uF 16V K
C9640NCB31CK-104XC CAPACITOR0.1uF 16V K
C9642NCB31HK-103XC CAPACITOR0.01uF 50V K
C9643NBE21CM-106XTA E CAPACITOR10uF 16V M
C9644NCB31HK-103XC CAPACITOR0.01uF 50V K
C9645NCB11HK-224XC CAPACITOR0.22uF 50V K
C9651NEAF1EM-475XE CAPACITOR4.7uF 25V M
C9652NCB31HK-222XC CAPACITOR2200pF 50V K
C9653NDC31HJ-101XC CAPACITOR100pF 50V J
C9655NEAF1AM-107XE CAPACITOR100uF 10V M
C9656NCB31HK-222XC CAPACITOR2200pF 50V K
C9657NCB31HK-222XC CAPACITOR2200pF 50V K
C9659NCB31HK-471XC CAPACITOR470pF 50V K
C9660NCB31HK-272XC CAPACITOR2700pF 50V K
C9661NEAF1EM-475XE CAPACITOR4.7uF 25V M
C9663NCS31HJ-271XC CAPACITOR270pF 50V J
C9664NCS31HJ-271XC CAPACITOR270pF 50V J
C9665NCB31HK-103XC CAPACITOR0.01uF 50V K
C9666NCB31CK-105XC CAPACITOR1uF 16V K
C9667NDC31HJ-121XC CAPACITOR120pF 50V J
C9668NCB31HK-332XC CAPACITOR3300pF 50V K
C9669NCB31CK-105XC CAPACITOR1uF 16V K
C9681NEAF1CM-226XE CAPACITOR22uF 16V M
C9683NCB31HK-222XC CAPACITOR2200pF 50V K
C9684NCB31HK-222XC CAPACITOR2200pF 50V K
C9685NFVB1EJ-224XMF CAPACITOR0.22uF 25V J
C9686NFVB1EJ-224XMF CAPACITOR0.22uF 25V J
C9687NCB11HK-224XC CAPACITOR0.22uF 50V K
C9688NCJ11EK-106X-RC CAPA
C9689NCB31CK-104XC CAPACITOR0.1uF 16V K
C9690NCB31CK-104XC CAPACITOR0.1uF 16V K
C9693NCB31HK-222XC CAPACITOR2200pF 50V K
C9694NCB31HK-222XC CAPACITOR2200pF 50V K
C9695NCB11HK-224XC CAPACITOR0.22uF 50V K
C9697NCB11HK-224XC CAPACITOR0.22uF 50V K
C9916NBE41EM-475XTA E CAPACITOR4.7uF 25V M
C9917NBE41EM-475XTA E CAPACITOR4.7uF 25V M
L1NQL79GM-4R7XCOIL4.7uH M
L30NQR0129-003XFERRITE BEADS
L31NQL093K-2R2XCOIL2.2uH K
L40NQR0129-003XFERRITE BEADS
L61NQR0129-003XFERRITE BEADS
L63NQL093K-1R8XCOIL1.8uH K
L201NQL382M-470XCOIL47uH M
L202NQL382M-470XCOIL47uH M
L301NQL382M-470XCOIL47uH M
L302NQL382M-100XCOIL10uH M
L701NQL79GM-100XCOIL10uH M
L706NQL79GM-4R7XCOIL4.7uH M
L901NQL114K-100XCOIL10uH K
L951QQR1660-001CHOKE COIL
L952QQR1660-001CHOKE COIL
L955QQR1660-001CHOKE COIL
L956QQR1660-001CHOKE COIL
L961QQR1660-001CHOKE COIL
L962QQR1660-001CHOKE COIL
L965QQR1660-001CHOKE COIL
L966QQR1660-001CHOKE COIL
L5001QQR1669-001CHOKE COIL
L7201NQL79GM-470XCOIL47uH M
L9071NQL56CK-220XNDUCTOR22uH K
C401NDC31HJ-101XC CAPACITOR100pF 50V J
C461NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C471NDC31HJ-471XC CAPACITOR470pF 50V J
C472NCB31CK-473XC CAPACITOR0.047uF 16V K
C473NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C491NDC31HJ-471XC CAPACITOR470pF 50V J
C492NCB31CK-473XC CAPACITOR0.047uF 16V K
C493NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C801NCB31CK-473XC CAPACITOR0.047uF 16V K
C802NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C804NCB31HK-102XC CAPACITOR1000pF 50V K
C805NCB31HK-102XC CAPACITOR1000pF 50V K
C806NCB31HK-102XC CAPACITOR1000pF 50V K
C811NCB31CK-473XC CAPACITOR0.047uF 16V K
C872NCB31CK-473XC CAPACITOR0.047uF 16V K
C874NCB31EK-473XC CAPACITOR0.047uF 25V K
C881NBE20JM-475XTA E CAPACITOR4.7uF 6.3V M
C882NCB31CK-473XC CAPACITOR0.047uF 16V K
C891NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C892NCB31CK-473XC CAPACITOR0.047uF 16V K
C431NDC31HJ-270XC CAPACITOR27pF 50V J
C432NDC31HJ-270XC CAPACITOR27pF 50V J
C433NCB31CK-104XC CAPACITOR0.1uF 16V K
C501NCB31HK-103XC CAPACITOR0.01uF 50V K
C502NCB31HK-223XC CAPACITOR0.022uF 50V K
C503NEAG0GM-227XE CAPACITOR220uF 4V M
C504NDC31HJ-220XC CAPACITOR22pF 50V J
C505NDC31HJ-220XC CAPACITOR22pF 50V J
C506NCB31HK-103XC CAPACITOR0.01uF 50V K
C507NCB31HK-223XC CAPACITOR0.022uF 50V K
C508NCB31HK-103XC CAPACITOR0.01uF 50V K
C509NCB31HK-223XC CAPACITOR0.022uF 50V K
C510NCB31HK-103XC CAPACITOR0.01uF 50V K
C511NCB31CK-104XC CAPACITOR0.1uF 16V K
C512NEAG0GM-227XE CAPACITOR220uF 4V M
C513NCB31HK-103XC CAPACITOR0.01uF 50V K
C514NDC31HJ-102XC CAPACITOR1000pF 50V J
C516NEAG0GM-227XE CAPACITOR220uF 4V M
C530NDC31HJ-102XC CAPACITOR1000pF 50V J
C551NCB31HK-103XC CAPACITOR0.01uF 50V K
C597NDC31HJ-102XC CAPACITOR1000pF 50V J
C598NDC31HJ-102XC CAPACITOR1000pF 50V J
C599NDC31HJ-102XC CAPACITOR1000pF 50V J
C601NEAF0JM-107XE CAPACITOR100uF 6.3V M
C602NCB31HK-681XC CAPACITOR680pF 50V K
C603NEAF0JM-107XE CAPACITOR100uF 6.3V M
C604NCB31HK-103XC CAPACITOR0.01uF 50V K
C605NCB31CK-104XC CAPACITOR0.1uF 16V K
C606NEAF0JM-476XE CAPACITOR47uF 6.3V M
C607NCB31CK-104XC CAPACITOR0.1uF 16V K
C608NCB31CK-104XC CAPACITOR0.1uF 16V K
C610NCB31CK-104XC CAPACITOR0.1uF 16V K
C612NCB31HK-103XC CAPACITOR0.01uF 50V K
C613NCB31HK-103XC CAPACITOR0.01uF 50V K
C614NCB31HK-103XC CAPACITOR0.01uF 50V K
C615NCB31CK-224XC CAPACITOR0.22uF 16V K
C616NEAF0JM-476XE CAPACITOR47uF 6.3V M
C617NCB31CK-104XC CAPACITOR0.1uF 16V K
C618NCB31CK-104XC CAPACITOR0.1uF 16V K
C621NCB31CK-104XC CAPACITOR0.1uF 16V K
Part No.Part NameDescriptionLocal
PHOTO
TRANSISTOR
C622NEAF0JM-476XE CAPACITOR47uF 6.3V M
C623NCS31HJ-470XC CAPACITOR47pF 50V J
C624NCB31HK-153XC CAPACITOR0.015uF 50V K
C625NCB31HK-103XC CAPACITOR0.01uF 50V K
C626NCB31HK-103XC CAPACITOR0.01uF 50V K
C627NCB31CK-104XC CAPACITOR0.1uF 16V K
C629NCB31EK-333XC CAPACITOR0.033uF 25V K
C630NCB31EK-333XC CAPACITOR0.033uF 25V K
C631NCS31HJ-471XC CAPACITOR470pF 50V J
C632NCS31HJ-471XC CAPACITOR470pF 50V J
C633NCB31CK-104XC CAPACITOR0.1uF 16V K
C634NCB31HK-472XC CAPACITOR4700pF 50V K
C635NCB31CK-153XC CAPACITOR0.015uF 16V K
C636NCB31CK-473XC CAPACITOR0.047uF 16V K
C637NCB31CK-473XC CAPACITOR0.047uF 16V K
C638NCB31HK-103XC CAPACITOR0.01uF 50V K
C640NCB31HK-103XC CAPACITOR0.01uF 50V K
C641NEAF0JM-476XE CAPACITOR47uF 6.3V M
C642NCS31HJ-101XC CAPACITOR100pF 50V J
C643NCB31CK-104XC CAPACITOR0.1uF 16V K
C644NCB31AK-334XC CAPACITOR0.33uF 10V K
C645NEAF0JM-476XE CAPACITOR47uF 6.3V M
C646NCB31CK-104XC CAPACITOR0.1uF 16V K
C647NCS31HJ-680XC CAPACITOR68pF 50V J
C648NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C649NCB31HK-562XC CAPACITOR5600pF 50V K
C651NEAF0JM-476XE CAPACITOR47uF 6.3V M
C652NCB31HK-103XC CAPACITOR0.01uF 50V K
C653NEAF0JM-476XE CAPACITOR47uF 6.3V M
C654NCB31CK-104XC CAPACITOR0.1uF 16V K
C655NCB31HK-103XC CAPACITOR0.01uF 50V K
C656NCB31CK-104XC CAPACITOR0.1uF 16V K
C658NEAF0JM-476XE CAPACITOR47uF 6.3V M
C659NCB31CK-104XC CAPACITOR0.1uF 16V K
C660NCS31HJ-101XC CAPACITOR100pF 50V J
C661NCB31HK-103XC CAPACITOR0.01uF 50V K
C662NCS31HJ-101XC CAPACITOR100pF 50V J
C663NCB31CK-104XC CAPACITOR0.1uF 16V K
C664NCB31HK-222XC CAPACITOR2200pF 50V K
C665NCB31CK-104XC CAPACITOR0.1uF 16V K
C666NCS31HJ-101XC CAPACITOR100pF 50V J
C668NEAF0JM-476XE CAPACITOR47uF 6.3V M
C669NCB31HK-103XC CAPACITOR0.01uF 50V K
C670NCB31CK-104XC CAPACITOR0.1uF 16V K
C671NBE21AM-106XTA E CAPACITOR10uF 10V M
C672NCB31CK-104XC CAPACITOR0.1uF 16V K
C674NCB31CK-104XC CAPACITOR0.1uF 16V K
C675NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C677NDC31HJ-471XC CAPACITOR470pF 50V J
C678NDC31HJ-471XC CAPACITOR470pF 50V J
C680NCB31CK-104XC CAPACITOR0.1uF 16V K
C682NEAF1EM-475XE CAPACITOR4.7uF 25V M
C683NCB31CK-104XC CAPACITOR0.1uF 16V K
C684NEAF1CM-476XE CAPACITOR47uF 16V M
C685NCB31CK-473XC CAPACITOR0.047uF 16V K
C686NCB31CK-473XC CAPACITOR0.047uF 16V K
C687NCB31CK-473XC CAPACITOR0.047uF 16V K
C688NCB31CK-473XC CAPACITOR0.047uF 16V K
C689NEAF1CM-476XE CAPACITOR47uF 16V M
C690NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C693NEAF1CM-476XE CAPACITOR47uF 16V M
C907NEAF0JM-476XE CAPACITOR47uF 6.3V M
C908NCB31CK-104XC CAPACITOR0.1uF 16V K
L432NQL093K-1R8XCOIL1.8uH K
L501NQL114K-470XCOIL47uH K
L502NQL114K-470XCOIL47uH K
L621NQL114K-470XCOIL47uH K
L622NQL114K-470XCOIL47uH K
L623NQL114K-470XCOIL47uH K
L624NQL114K-470XCOIL47uH K
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W D
Ω
1/16W D
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
Ω
1/16W J
Ω
Ω
1/16W J
Ω
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
Ω
Ω
Ω
Ω
1/16W J
Ω
Ω
Ω
1/16W J
Ω
1/16W J
Ω
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
Ω
Ω
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W D
Ω
1/16W D
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
3-20
Symbol No.
L651NQL114K-470XCOIL47uH K
L652NQL114K-470XCOIL47uH K
L653NQL114K-470XCOIL47uH K
L654NQL114K-470XCOIL47uH K
L655NQL114K-470XCOIL47uH K
L656NQL114K-470XCOIL47uH K
L901NQL114K-470XCOIL47uH K
No additional / supplemental order of WARRANTY CARDs are available.
P11
P7
P6
A17
P2
A2 A3 A4 A5
A6 A7 A8 A9
P10
A16
Block No.
M
3
P5
M
M
P9
KIT:
P2
A1
P3
A10 A11
A12 A13
A14
A19
P4
A18
A15
A20
A21
P1
3-22
P8
Packing and Accessories
Block No. [M][3][M][M]
Symbol No.Part No.Part NameDescriptionLocal
A 1LVT1372-002AINST BOOKSPA GRE PORSHX851E
A 1LVT1372-007AINST BOOKSPA TUR PERSHX851EU
A 1LVT1372-004AINST BOOKDUT SWE DAN FINSHX851EX
A 1LVT1372-006AINST BOOKPOL CZE HUNSHX851EY
A 2LVT1372-001AINST BOOKENG FRE ITASHX851E
A 2LVT1372-003AINST BOOKENG FRESHX851EU,SHX851EX
A 2LVT1372-005AINST BOOKENG GER RUSSHX851EY
A 3LVT1372-008AINSTALL MANUALSHX851E
A 3LVT1372-010AINSTALL MANUALSHX851EU,SHX851EX
A 3LVT1372-012AINSTALL MANUALSHX851EY
A 4LVT1372-009AINSTALL MANUALSHX851E
A 4LVT1372-014AINSTALL MANUALSHX851EU
A 4LVT1372-011AINSTALL MANUALSHX851EX
A 4LVT1372-013AINSTALL MANUALSHX851EY
A 5VND3046-001SERIAL TICKET
A 6VND3050-002IDENTITY CARDSHX851E,SHX851EX,SHX851EY
A 7------------WARRANTY CARDBT-54026-1
A 8LVT1300-003AIMAGE CONV.SHEE
A 9QAM0688-001CD ROM
A 10VKZ4027-202PLUG NUT
A 11VKH4871-003SSMOUNT BOLT
A 12VKZ4328-003LOCK NUT
A 13QYWSS50A010ZAWASHER0.1mm/5mm x
A 14GE40130-002AHOOK(x2)
A 15FSJB3002-00FHARD CASE ASSY
A 16GE20137-003AMOUNTING SLEEVE
A 17LV21648-203ATRIM PLATE
A 18RM-RK300REMOCON
A 19------------BATTERY
A 20QAM0566-002CAR CABLE
A 21QQR0491-001FERRITE CORETDK (GRAY)
KITSRW-SHX751ESCREW PART KITA10 A11 A12 A13 A14
P 1QPA01003503POLY BAG10cm x 35cm
P 2QPA01703505PPOLY BAG17cm x 35cm(x2)
P 3QPA00801205POLY BAG8cm x 12cm
P 4QPC01002515POLY BAG10cm x 25cm
P 5QPA01003003POLY BAG10cm x 30cm
P 6QPC03004315PPOLY BAG30cm x 43cm
P 7LV36205-001ACARTON
P 8LV36270-001ASEPARATOR
P 9LV11111-001ACUSHION(L)
P 10LV11112-001ACUSHION(R)
P 11 LVT1408-002ACAUTION SHEET
3-23
SCHEMATIC DIAGRAMS
CD/SD RECEIVER
KD-SHX851
CD-ROM No.SML200506
Area suffix
E ------------- Southern Europe
EX ------------ Northern Europe
EY ------------- Eastern Europe
EU ------------------------- Turkey
SOURCE
T/P
DISP
BACK
BAND
MENU
PICT
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
Contents
Block diagram
Standard schematic diagrams
Printed circuit boards
2-1
2-2
2-8 to 10
COPYRIGHT 2005 Victor Company of Japan, Limited.
No.MA192SCH
2005/6
Safety precaution
!
!
Burrs formed during molding may be left over on some parts of the chassis. Therefore,
pay attention to such burrs in the case of preforming repair of this system.
Please use enough caution not to see the beam directly or touch it in case of an
adjustment or operation check.