JVC KD-SH99RE, KD-SH99REX Instructions Manual

CD RECEIVER
KD-SH99R
ENGLISH
DEUTSCH
FRANÇAIS
Detachable
ATT
ANGLE
CD
FM
AM
CH
AUX SEL
VOLUME
RM-RK100
EQ
R D
For installation and connections, refer to the separate manual. Angaben zu Einbau und Verkabelung entnehmen Sie bitte der gesonderten Anleitung. Pour l’installation et les raccordements, se référer au manuel séparé. Zie de afzonderlijke handleiding voor details aangaande het installeren en verbinden van het toestel.
NEDERLANDS
BEDIENUNGSANLEITUNG
MANUEL D’INSTRUCTIONS
GEBRUIKSAANWIJZING
INSTRUCTIONS
LVT0655-001A
[E/EX]
Position And Reproduction Of Labels
Bottom Panel of the main unit
ENGLISH
CAUTION: Invisible laser radiation when open and interlock failed or defeated. AVOID DIRECT EXPOSURE TO BEAM. (e)
Name/Rating plate
CLASS LASER
Caution: This product contains a laser component of higher laser class than Class 1.
1
PRODUCT
ADVARSEL: Usynlig laser­stråling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgåudsæt­telse for stråling. (d)
VARNING: Osynlig laser­strålning när denna del är öppnad och spärren är urkopplad. Betrakta ej strålen. (s)
VAR O: Avattaessa ja suojalukitus ohitettaessa olet alttiina näkymättö­mälle lasersäteilylle. Älä katso säteeseen. (f)
IMPORTANT FOR LASER PRODUCTS
Precautions:
1. CLASS 1 LASER PRODUCT
2. CAUTION: Invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.
3. CAUTION: Do not open the top cover. There are no user-serviceable parts inside. Leave all servicing to qualified service personnel.
4. CAUTION: This CD player uses invisible laser radiation and is equipped with safety switches to prevent radiation emission when unloading CDs. It is dangerous to defeat the safety switches.
5. CAUTION: Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
How to reset your unit
Press the reset button on the front panel using a ball-point pen or similar tool.
CAUTION:
NEVER insert your finger in between the control panel and the unit, as it may get
Note:
Your preset adjustments – such
caught or hurt. (See page 35.)
as preset channels or sound adjustments – will be erased.
Note:
For security reasons, a numbered ID card is provided with this unit, and the same ID number is imprinted on the unit’s chassis. Keep the card in a safe place, as it will help the authorities to identify your unit if stolen.
BEFORE USE
*
For safety....
• Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.
• Stop the car before performing any complicated operations.
*
Temperature inside the car....
If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.
2
Thank you for purchasing a JVC product. Please read all instructions carefully before oper ation,
to ensure your complete understanding and to obtain the best possible performance from the unit.
CONTENTS
How to reset your unit............................... 2
LOCATION OF THE BUTTONS ............ 4
Control panel ........................................... 4
Remote controller .................................... 5
Preparing the remote controller ................ 6
BASIC OPERATIONS ...................... 7
RADIO BASIC OPERATIONS ............. 8
Listening to the radio ................................ 8
Storing stations in memory ....................... 9
Tuning into a preset station ...................... 10
RDS OPERATIONS ........................ 11
What you can do with RDS EON.............. 11
Other convenient RDS functions and
adjustments........................................... 14
CD OPERATIONS .......................... 17
Playing a CD............................................ 17
Locating a track or particular portion
on a CD ................................................. 18
Selecting CD playback modes.................. 18
Playing a CD Text .................................... 19
Prohibiting disc ejection............................ 19
MP3 INTRODUCTION ..................... 20
What is MP3? .......................................... 20
How are MP3 files recorded and
played back? ......................................... 20
MP3 OPERATIONS ........................ 22
Playing an MP3 disc ................................. 22
Locating a file or particular portion
on an MP3 disc ..................................... 23
Selecting MP3 playback modes ............... 26
SOUND ADJUSTMENTS .................. 27
Adjusting the sound ................................. 27
Selecting preset sound modes ................. 28
Storing your own sound adjustments ....... 29
OTHER MAIN FUNCTIONS ............... 30
Setting the clock ...................................... 30
Changing the general settings (PSM) ...... 30
Assigning names to the sources .............. 34
Changing the control panel angle............. 35
Detaching the control panel...................... 36
EXTERNAL COMPONENT OPERATIONS .. 37
Playing external components ................... 37
CD CHANGER OPERATIONS ............. 39
Playing CDs ............................................. 39
Selecting CD playback modes.................. 40
DAB TUNER OPERATIONS ............... 41
Tuning into an ensemble and one of the
services ................................................. 41
Storing DAB services in memory ............. 43
Tuning into a preset DAB service ............. 44
What you can do more with DAB.............. 44
ADDITIONAL INFORMATION ............. 45
TROUBLESHOOTING...................... 46
MAINTENANCE ............................ 48
Handling discs ......................................... 48
SPECIFICATIONS .......................... 49
ENGLISH
About the demonstration mode (DEMO MODE)...
When shipped from the factory, “DEMO MODE” is set to “DEMO ON” in this unit. The following demonstration, introducing the main features equipped with this unit, will appear on the display automatically if no sound comes in for 3 minutes. (See page 33.)
MP3 :(Enables you to play MP3 discs.)
24bit DAC :(24 bit digital-analog converter: Gives you a high quality sound after D/A conversion.)
HS TUNER : (High-sensitivity Tuner: Enables a fine reception of stations.)
EQUALIZER :(Enables you to fine-adjust the sound to match your preference.)
SUB WOOFER :(Enables you to connect a subwoofer and to adjust its output level.)
CAUTION on Volume Setting
CDs produce very little noise compared with other sources. If the volume level is adjusted for the tuner, for example, the speakers may be damaged by the sudden increase in the output level. Therefore, lower the volume before playing a disc and adjust it as required during playback.
3
LOCATION OF THE BUTTONS
Control panel
1
ENGLISH
1 0 (eject) button 2 Control dial 3 SEL (select) button 4 EQ (equalization) button 5 D (display) button 6 TP (traffic programme) button 7 PTY (prog ramme type) button 8 M/B (mode/band) button 9 4/¢ buttons
Also function as SSM buttons when pressed together.
p ATT (angle/attenuator) button
2
3
4 5
t
6
7
q Auxiliary input jack w (control panel release) button e Remote sensor r Number buttons
t SOURCE (standby/on) button y Reset button
8
ry
MO (monaural) button
LO (local) button
INT (intro scan) button
RPT (repeat) button
RND (random) button
DVD/Video component operation buttons
9
e
p
w
q
How to use M/B (mode/band):
If you press M/B (mode/band), this button functions as the Mode button and the unit goes into functions mode whereby the number buttons and the 4/¢ buttons work as different function buttons.
T o use these b uttons as number b uttons and 4/¢ b uttons again after pressing M/B (mode/ band), wait for 5 seconds without pressing any number button until the functions mode is cleared.
• Pressing M/B (mode/band) again also clears the functions mode.
4
Normally
During functions mode
Equalizing pattern indicator
Time countdown indicator
Remote controller
1
2
ATT
ANGLE
CD
DAB
FM
AM
DISC
PRESET
R D
EQ
PRESET
3
4
5 6
7
5 • Searches for stations while listening to the
radio.
• Selects ensembles while listening to the DAB tuner if pressed briefly.
• Selects services while listening to the DAB tuner if pressed and held.
• Fast-f orwards or reverses the track/file if pressed and held while listening to any disc.
• Skips to the beginning of the next track/file or goes back to the beginning of the current (or previous) trac k/file if pressed briefly while listening to any disc. (See pages 18 and 23.)
ENGLISH
CH
DISC
AUX SEL
VOLUME
8 9
p
RM-RK100
1 • Turns on the unit if pressed when the unit is
turned off.
• T urns off the unit if pressed and held until “SEE YOU” appears on the display.
• Drops the volume level if pressed briefly, and “ATT” flashes on the display. Press again to resume the volume.
2 • CD : Selects CD player.
• FM : • Selects FM tuner.
Each time you press the button, FM band (FM1, FM2 and FM3) changes.
• Selects DAB tuner if pressed and held.* Each time you press and hold the button, DAB band (D AB 1, D AB 2 and DAB 3) changes.
• AM : Selects AM tuner.
• CH : Selects CD changer.*
• AUX : Selects the external components. Each time you press the button, “AUX INPUT” and “LINE INPUT” are alternately selected.
3 Changes the angle of the control panel to four
positions.
4 Selects the sound modes .
Each time you press the button, sound modes change.
6 • Changes the preset channel number while
listening to the radio (or the DAB tuner). Each time you press the button, the preset channel number changes, and the selected station (or service) is tuned into.
• Skips to the first file of the next directory or the first file of the previous directory if pressed and held while listening to an MP3 disc. (See page 24.)
• Skips to the first file of the next directory or the first file of the previous directory of the same hierarchy level if pressed briefly while listening to an MP3 disc. (See page 25.)
7 • Changes the disc number while listening to the
CD changer. Each time you press the button, the disc number changes, and the selected disc starts playing.
• Skips to the first file of a directory of an upper hierarchy level or a lower hierarchy level if pressed br iefly while listening to an MP3 disc. (See page 25.)
8 Skips to the root directory while listening to an
MP3 disc. (See page 25.)
9** Selects the sound adjustment items.
Each time you press the button, the items change.
p** • Changes the volume.
• Adjusts the sound mode (after SEL is pressed).
* Without connecting the DAB tuner or CD
changer, you cannot select it as the sour ce to play.
** These buttons do not function in the preferred
setting mode adjustment.
5
Preparing the remote controller
Before using the remote controller:
• Aim the remote controller directly at the remote sensor on the main unit. Make sure there is no
ENGLISH
obstacle in between.
2. Place the battery.
Slide the battery into the holder with the + side facing upwards so that the battery is fixed in the holder.
Lithium coin battery (product number: CR2025)
3. Return the battery holder.
Insert again the battery holder pushing it until you hear a clicking sound.
Remote sensor
• Do not expose the remote sensor to strong light (direct sunlight or artificial lighting).
Installing the battery
When the controllable range or effectiv eness of the remote controller decreases, replace the battery.
1. Remove the battery holder.
1) Push out the battery holder in the direction indicated by the arrow using a ball-point pen or a similar tool.
2) Remove the battery holder.
(back side)
1)
2)
(back side)
WARNING:
• Store the battery in a place where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately.
• Do not recharge, short, disassemble or heat the battery or dispose it in a fire. Doing any of these things may cause the battery to give off heat, crack or start a fire.
• Do not leave the battery with other metallic materials. Doing this may cause the battery to give off heat, crack or start a fire.
• When throwing away or saving the battery, wrap it in tape and insulate; otherwise, the battery may start to give off heat, crack or start a fire.
• Do not poke the battery with tweezers or similar tools. Doing this may cause the battery to give off heat, crack or start a fire.
6
BASIC OPERATIONS
Note:
When you use this unit for the first time, set the built-in clock corr ectly, see page 30.
ENGLISH
2
1
Turn on the power and select the
1
source.
When you press the button for the first time, the power comes on. Then each time you press the button, the source changes as follows:
FM TUNER
AM TUNER
* If a disc is not in the loading slot, you cannot
select CD as the source to play.
** Without connecting the DAB tuner or CD
changer, you cannot select it as the sour ce to play.
To operate the tuner (FM or AM),
see pages 8 – 10.
To play a CD,
see pages 17 – 19.
To play an MP3 disc,
see pages 22 – 26.
To operate external components
(AUX INPUT and LINE INPUT), see pages 37 – 38.
To operate the CD changer,
see pages 39 – 40.
To operate the DAB tuner,
see pages 41 – 44.
DAB TUNER
AUX INPUT
**
CD CHANGER
LINE INPUT
CD PLAY
2
Adjust the volume.
To increase the volume.
To decrease the volume.
*
**
Volume level indicator
Note:
After adjusting the volume, you can push in the control dial to avoid unintended operations. To use it again, push the control dial again to make it come out.
3
Adjust the sound as you want.
Volume level appears.
(See page 27.)
To drop the volume in a moment
Press and hold /ATT while listening to any source. “ATT” starts flashing on the display, and the volume level will drop in a moment. To resume the previous volume level, press and hold the button again.
• If you turn the control dial clockwise, you can also restore the sound.
To turn off the power
Press and hold SOURCE until “SEE YOU” appears on the display.
7
ENGLISH
RADIO BASIC OPERATIONS
Listening to the radio
You can use either automatic searching or manual searching to tune into a particular station.
Searching a station automatically: Auto search
1
Select FM or AM.
1 Press SOURCE
repeatedly to select FM or AM as the source.
2 If necessary , press and
hold M/B (mode/band) for more than 1 second repeatedly to select the FM band number. Each time you press and hold the button, the FM band changes as follows:
FM 1 FM 2 FM 3
Selected band appears.
Note:
This receiver has three FM bands (FM1, FM2, FM3). You can use any one of them to listen to an FM broadcast.
To stop searching before a station is received,
press the same button you have pressed for searching.
T o tune into FM stations only with strong signals
1 Press M/B (mode/band) to enter the functions
mode while listening to an FM broadcast.
2 Press LO (local) while still in the functions
mode, so that the LOCAL indicator lights up on the display. This function works only while searching FM stations, including SSM preset. Each time you press the button, the LOCAL indicator lights up and goes off alternately .
Searching a station manually: Manual search
1
Select FM or AM .
1 Press SOURCE
repeatedly to select FM or AM as the source.
2 If necessary , press and
hold M/B (mode/band) for more than 1 second repeatedly to select the FM band number. Each time you press and hold the button, the FM band changes as follows:
FM 1 FM 2 FM 3
2
Start searching a station.
Press ¢ to search stations of higher frequencies.
Press 4 to search stations of lower frequencies.
When a station is received, searching stops.
8
Note:
This receiver has three FM bands (FM1, FM2, FM3). You can use any one of them to listen to an FM broadcast.
2
Press and hold ¢ or 4 until “M” (manual) starts flashing on the display.
3
T une into a station you want while “M” is flashing.
Press ¢ to tune into stations of higher frequencies.
Press 4 to tune into stations of lower frequencies.
• If you release your finger from the button, the manual mode will automatically turn off after 5 seconds.
• If you hold down the button, the frequency keeps changing until you release the button.
Storing stations in memory
You can use one of the following two methods to store broadcasting stations in memory.
• Automatic preset of FM stations: SSM (Strong­station Sequential Memory)
• Manual preset of both FM and AM stations
FM station automatic preset: SSM
You can preset 6 local FM stations in each FM band (FM1, FM2 and FM3).
1
Select the FM band (FM1 – 3) you want to store FM stations into.
1 Press SOURCE
repeatedly to select FM.
2 If necessary , press and
hold M/B (mode/band) for more than 1 second repeatedly to select the FM band. Each time you press and hold the button, the FM band changes as follows:
FM 1 FM 2 FM 3
ENGLISH
When an FM stereo broadcast is hard to receive:
1 Press M/B (mode/band) to enter
the functions mode while listening to an FM stereo broadcast.
2 Press MO (monaural) while still in
the functions mode, so that the MO indicator lights up on the display.
• Each time you press the button, the MO and ST (stereo) indicators light up alternately .
Lights up when receiving an FM broadcast in stereo.
When the MO indicator is lit on the display, the sound you hear becomes monaural but the reception will be improved (the ST indicator goes off).
The MO indicator lights up.
2
Press and hold both buttons for more than 2 seconds.
“SSM” appears, then disappears when automatic preset is over.
Local FM stations with the strongest signals are searched and stored automatically in the band number you have selected (FM1, FM2 or FM3). These stations are preset in the number buttons — No.1 (lowest frequency) to No.6 (highest frequency). When automatic preset is over, the station stored in number button 1 will be automatically tuned into.
9
Manual preset
You can preset up to 6 stations in each band (FM1, FM2, FM3 and AM) manually.
Ex.: Storing an FM station of 88.3 MHz into the
ENGLISH
preset number 1 of the FM1 band
1
Select the band (FM1 – 3, AM) you want to store stations into (in this example, FM1).
1 Press SOURCE
repeatedly to select FM as the source.
2 If necessary , press and
hold M/B (mode/band) for more than 1 second repeatedly to select FM1. Each time you press and hold the button, the FM band changes as follows:
FM 1 FM 2 FM 3
Tuning into a preset station
You can easily tune into a preset station. Remember that you must store stations first. If you have not stored them yet, see “Storing stations in memory” on page 9.
1
Select the band (FM1 – 3, AM).
1 Press SOURCE
repeatedly to select FM or AM as the source.
2 If necessary, press M/B
(mode/band) for more than 1 second repeatedly to select the FM band number. Each time you press and hold the button, the FM band changes as follows:
FM 1 FM 2 FM 3
2
Tune into a station of 88.3 MHz.
Press ¢ to tune into stations of higher frequencies.
Press 4 to tune into stations of lower frequencies.
3
Press and hold the number button (in this example, 1) for more than 2 seconds.
“P1” flashes for a while.
4
Repeat the above procedure to store other stations into other preset numbers.
Notes:
• A previously pr eset station is erased when a new station is stored in the same preset number.
• Preset stations are er ased when the power supply to the memory circuit is interrupted (for example, during battery replacement). If this occurs, preset the stations
10
again.
2
Select the number (1 – 6) for the preset station you want.
If the sound quality decreases and the stereo effect is lost while listening to an FM station...
In some areas, adjacent stations may interfere with each other. If such interference occurs, this unit can automatically reduce the interference noise (the initial setting when shipped from the factory). However, in this case, the sound quality will be degraded and the stereo effect will also be lost. If you do not want to degrade the sound quality and to lose the stereo effect, rather than to eliminate the interference noise, see “To change the FM tuner selectivity – IF FILTER” on page 33.
RDS OPERATIONS
What you can do with RDS EON
RDS (Radio Data System) allows FM stations to send an additional signal along with their regular programme signals. For e xample, the stations send their station names, as well as information about what type of programme they broadcast, such as sports or music, etc. Another advantage of RDS function is called “EON (Enhanced Other Networks).” The EON indicator lights up while receiving an FM station with the EON data. By using the EON data sent from a station, you can tune into a different station of a different network broadcasting your favorite programme or traffic announcement while listening to another programme or to another source such as CD.
By receiving the RDS data, this unit can do the following:
• Tracing the same programme automatically (Network-Tracking Reception)
• Standby Reception of TA (Traffic Announcement) or your fa vorite programme
• PTY (Programme Type) search
• Programme search
• And some other functions
Tracing the same programme automatically (Network-Tracking Reception)
When driving in an area where FM reception is not good, the tuner built in this unit automatically tunes into another RDS station, broadcasting the same programme with stronger signals. So, you can continue to listen to the same programme in its finest reception, no matter where you drive. (See the illustration on the next page.) Two types of the RDS data are used to make Network-Tracking Reception work correctly — PI (Programme Identification) and AF (Alternative Frequency). Without receiving these data correctly from the RDS station you are listening to, Network-Tracking Reception will not operate.
To use Network-Tracking Reception, press and hold TP (traffic prog ramme) for more than 1 second. Each time you press and hold the button, Network­Tracking Reception modes change as follows:
Mode 1
(AF)
Mode 1
Mode 2
Mode 3
Mode 1
Network-Tracking Reception is activated with Regionalization set to “off.” Switches to another station within the same network when the receiving signals from the current station become weak.
In this mode, the programme may differ from the one
currently received.
Mode 2
Network-Tracking Reception is activated with Regionalization set to “on.” Switches to another station, within the same network, broadcasting the same programme when the receiving signals from the current station become weak.
Mode 3
Network-Tracking Reception is deactivated.
Note:
If a DAB tuner is connected and Alternative Reception (for DAB services) is activated, Network-Tracking Reception is also activated automatically. On the other hand, Networking-Tracking Reception cannot be deactivated without deactivating Alternative Reception. (See page 44.)
Mode 2 Mode 3
(AF/REG) (Canceled)
AF indicator
REG indicator
: lights : goes off
AF REG
indicator indicator
ENGLISH
11
The same programme can be received on different frequencies.
Programme 1 broadcasting on frequency A
ENGLISH
Programme 1 broadcasting on frequency B
Programme 1 broadcasting on frequency C
Programme 1 broadcasting on frequency E
Programme 1 broadcasting on frequency D
Using Standby Reception
PTY Standby Reception
When you press PTY while listening to an FM station, the PTY indicator is lit during reception of a PTY station and the PTY standby mode is engaged. The selected PTY name stored on page 13 flashes for 5 seconds.
• When the station being received is not a PTY station, the PTY indicator flashes. Press ¢ or 4 to engage the PTY standby mode. “SEARCH” appears on the display, and PTY station sear c h starts. When a PTY station is tuned into, the PTY indicator is lit.
7 If you are listening to a CD or other connected
components and wish to listen to a selected PTY broadcast, press PTY to enter the PTY standby mode. (The PTY indicator lights up.)
Standby Reception allows the unit to switch temporarily to your favorite programme (PTY: Programme Type) and Traffic Announcement (TA) from the current source (another FM station, CD or other connected components).
Standby Reception will not work if you are listening
to an AM station.
TA Standby Reception
When you press TP while listening to an FM station, the TP indicator is lit during reception of a TP (Traffic Programme) station and the TA standby mode is engaged.
When the station being received is not a TP station,
the TP indicator flashes. Press ¢ or 4 to engage the T A standby mode . “SEARCH” appears on the display, and TP station search starts. When a TP station is tuned into, the TP indicator is lit.
7 If you are listening to a CD or other connected
components and wish to listen to a TP station, press TP to enter the TA standby mode. (The TP indicator lights up.)
If the selected PTY programme starts broadcasting while the PTY standby mode is active, the selected PTY name appears and the playback source changes to the FM band. The selected PTY programme can then be heard.
T o deactivate the PTY standby mode, press PTY again.
If a traffic programme starts broadcasting while the T A standb y mode is active, “TRAFFIC” appears and the playback source changes to the FM band. The volume increases to the preset T A volume le vel (see page 15) and the traffic programme can be heard.
To deactivate the TA standby mode, press TP again.
12
Selecting your favorite programme for PTY Standby Reception
You can select your favorite programme for PTY Standby Reception to store in memory. When shipped from the factory, “NEWS” is stored as the programme type for PTY Standb y Reception.
1
Press and hold SEL (select) for more than 2 seconds so that one of the PSM items appears on the display. (PSM: see page 31.)
Searching your favorite programme
You can search one of your 6 favorite programme types stored in memory. When shipped from the factory, the following 6 programme types hav e been stored in the n umber buttons (1 to 6). To store your favorite programme types, see below. To search your favorite programme type, see page 14.
1
POP M
45
CLASSICS
2
ROCK M EASY M
AFFAIRS
3
6
VARIED
ENGLISH
2
Select “PTY STBY” (standby) if not shown on the display.
3
Select one of twenty-nine PTY codes. (See page 16.)
Selected code name appears on the display and is stored into memory.
4
Press SEL (select) to finish the setting.
To store your favorite programme types
1
Press and hold SEL (select) for more than 2 seconds so that one of the PSM items appears on the display. (PSM: see page 31.)
2
Select “PTY SEARCH” if not shown on the display.
3
Select one of twenty-nine PTY codes. (See page 16.)
Selected code name appears on the display.
• If the code already stored in memory is selected, it will flash on the display.
CONTINUED ON THE NEXT PAGE
13
4
Press and hold the number button for more than 2 seconds to store the PTY code selected into the preset number you want.
ENGLISH
“MEMORY” and the selected code name will flash alternately. Then, only the selected code name will continue flashing on the display.
• If there is a station broadcasting a programme of the same PTY code as you selected, that station is tuned into.
• If there is no station broadcasting a programme of the same PTY code as you selected, the station will not change.
Note:
In some areas, the PTY search will not work correctly.
Other convenient RDS functions
5
Press SEL (select) to finish the setting.
To search your favorite programme type
1
Press and hold PTY (programme type) for more than 1 second while listening to an FM station.
The last selected PTY code appears.
2
Select one of the PTY codes stored in the preset number buttons (1 to 6).
and adjustments
Automatic selection of the station when using the number buttons
Usually when you press the number button, the preset station is tuned into. However, when the preset station is an RDS station, something different will happen. If the signals from that preset station are not sufficient for good reception, this unit, using the AF data, tunes into another frequency broadcasting the same programme as the original preset station is broadcasting. (Programme search)
• The unit takes some time to tune into another station using programme search.
T o activate prog ramme search, follow the procedure below .
• See also “Changing the general settings (PSM)” on page 30.
1 Press and hold SEL (select) for more than 2
seconds so that one of the PSM items appears on the display.
2 Press ¢ or 4 to select
“P-SEARCH.”
3 Turn the control dial clockwise to select
“SEARCH ON.” Now programme search is activated.
4 Press SEL (select) to finish the setting.
Ex.: When “ROCK M” is stored in preset
number button 2
PTY search for your favorite programme starts after 5 seconds.
14
To cancel programme search, repeat the same procedure and select “SEARCH OFF” in step 3 by turning the control dial counterclockwise.
Changing the display mode while listening to an FM station
You can change the initial indication on the display to station name (PS NAME) or station frequency (FREQUENCY) while listening to an FM RDS station.
• See also “Changing the general settings (PSM)” on page 30.
1 Press and hold SEL (select) for more than 2
seconds so that one of the PSM items appears on the display.
2 Press ¢ or 4 to select “TUNER DISP”
(tuner display).
3 T urn the control dial to set to the desired indication
(“FREQUENCY” or “PS NAME”).
4 Press SEL (select) to finish the setting.
Note:
By pressing D (display), you can change the display while listening to an FM RDS station only. Each time you press the b utton, the following information appears on the display:
Setting the TA volume level
You can preset the volume level for TA Standby Reception. When a traffic programme is received, the volume lev el automatically changes to the preset level.
• See also “Changing the general settings (PSM)” on page 30.
1 Press and hold SEL (select) for more than 2
seconds so that one of the PSM items appears on the display.
2 Press ¢ or 4 to select “TA VOL.” 3 T urn the control dial to set to the desired volume.
You can set it from “TA VOL 00” to “TA VOL 50.”
4 Press SEL (select) to finish the setting.
Automatic clock adjustment
When shipped from the factory, the clock built in this unit is set to be readjusted automatically using the CT (Clock Time) data in the RDS signal. If you do not want to use automatic clock adjustment, follow the procedure below.
• See also “Changing the general settings (PSM)” on page 30.
ENGLISH
Station name
(PS NAME)
Station frequency
(FREQ)
Programme type
(PTY)
Then, the display goes back to the original indication
in several seconds.
1 Press and hold SEL (select) for more than 2
seconds so that one of the PSM items appears on the display.
2 Press ¢ or 4 to select “AUTO ADJ.” 3 Turn the control dial counterclockwise to select
“ADJUST OFF.” Now automatic clock adjustment is canceled.
4 Press SEL (select) to finish the setting.
T o reactivate c lock adjustment, repeat the same
procedure and select “ADJUST ON” in step 3 by turning the control dial clockwise.
Note:
You must stay tuned to the same station for more than 2 minutes after setting “AUTO ADJ” to “ADJUST ON.” Otherwise, the clock time will not be adjusted. (This is because the unit takes up to 2 minutes to capture the CT data in the RDS signal.)
15
PTY codes
NEWS: News AFFAIRS: Topical programmes expanding
on current news or affairs
ENGLISH
INFO: Programmes which impart advice
on a wide variety of topics SPORT: Sport events EDUCATE: Educational programmes DRAMA: Radio plays CULTURE: Programmes on national or
regional culture SCIENCE: Programmes on natural science
and technology VARIED: Other programmes like comedies
or ceremonies POP M: Pop music ROCK M: Rock music EASY M: Easy-listening music LIGHT M: Light music CLASSICS: Classical music OTHER M: Other music WEATHER: Weather information FINANCE: Reports on commerce, trading,
the Stock Market, etc. CHILDREN: Entertainment programmes for
children
SOCIAL: Progr ammes on social activities RELIGION: Programmes dealing with any
aspect of belief or faith, or the nature of existence or ethics
PHONE IN: Programmes where people can
express their views either by phone or in a public forum
TRAVEL: Programmes about travel
destinations, package tours, and travel ideas and opportunities
LEISURE: Programmes concerned with
recreational activities such as
gardening, cooking, fishing, etc. JAZZ: Jazz music COUNTRY: Country music NATION M: Current popular music from
another nation or region, in that
country’s language OLDIES: Classic pop music FOLK M: Folk music DOCUMENT: Programmes dealing with factual
matters, presented in an
investigative style
16
CD OPERATIONS
ENGLISH
When playing an MP3 disc, refer also to “MP3 OPERATIONS” on pages 22 to 26.
Playing a CD
1
Open the loading slot.
The control panel moves down, and the loading slot appears.
Note:
When an external component is connected to the auxiliary input jack, be careful of handling a disc.
2
Insert a disc into the loading slot.
The unit draws the disc, the control panel goes back to the previous position (see page 35), and CD play starts automatically.
• All the tracks on the disc will be played repeatedly until you stop playback—All Track Repeat Play.
Note:
Do not insert any 8 cm disc into the loading slot as it will get stuck inside.
The display changes to show the following:
Notes:
• When a disc is in the loading slot, selecting “CD” as the source by pressing SOURCE starts CD play.
• When a disc is inserted upside down, the disc automatically ejects.
• When you play a CD Text, the disc title and performer appear on the display. Then the current track title appears on the display, followed by the track number and elapsed playing time. See also “Playing a CD Text” (page 19) and “To select the scroll mode – SCROLL” (page 32). If a CD Text includes too much text information, some may not appear on the display.
• If you change the source, CD play also stops (without ejecting the disc).
To stop play and eject the disc
Press 0. CD play stops, the control panel moves down, and the disc automatically ejects from the loading slot.
To return the control panel to its previous position, press 0 again.
• If you keep the loading slot open for one minute (or 30 seconds when you have ejected a disc with the ignition key turned to “OFF”), a beep sounds and the control panel returns to its previous position. Be careful not to get the disc or your finger caught in between the control panel and the unit.
Total track number of the inserted disc
Current track Elapsed playing time
Total playing time of the inserted disc
Note:
If the ejected disc is not removed within 15 seconds, the disc is automatically inserted again into the loading slot to protect it from dust. (CD play will not start this time.)
17
Loading...
+ 37 hidden pages