JVC KD-S7350, KD-S690 User Manual

CD RECEIVER KD-S7350/KD-S690

ENGLISH

RECEPTOR CON CD KD-S7350/KD-S690

RECEPTEUR CD KD-S7350/KD-S690

KD-S7350

S

KD-S690

S

COMPACT

DIGITAL AUDIO

For installation and connections, refer to the separate manual.
Para la instalación y las conexiones, refiérase al manual separado.
Pour l’installation et les raccordements, se référer au manuel séparé.

ESPAÑOL

FRANÇAIS

INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

For customer Use:

Enter below the Model No. and
Serial No. which are located on
the top or bottom of the
cabinet. Retain this information
for future reference.

Model No.

Serial No.

GET0131-001A

[J]

INFORMATION (For U.S.A.)

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with

ENGLISH

the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

– Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT FOR LASER PRODUCTS

Precautions:

1. CLASS 1 LASER PRODUCT

2. CAUTION: Invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure
to beam.

3. CAUTION: Do not open the top cover. There are no user-serviceable parts inside. Leave all
servicing to qualified service personnel.

4. CAUTION: This CD player uses invisible laser radiation, however, is equipped with safety switches
to prevent radiation emission when unloading CDs. It is dangerous to defeat the safety switches.

5. CAUTION: Use of controls, adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.

How to reset your unit

While holding SEL (select), press (standby/on/attenuator) for more than 2 seconds.
This will reset the built-in microcomputer.

(standby/on/attenuator)

SEL (select)

Notes:

• Your preset adjustments—such as preset channels or sound adjustments—will also be erased.

• If a CD is in the unit, it will eject when you reset the unit. Be careful not to drop the CD.

2

Thank you for purchasing a JVC product. Please read all instructions carefully before operation,

to ensure your complete understanding and to obtain the best possible performance from the unit.

CONTENTS

How to reset your unit ............................... 2

How to use the M (MODE) button ............. 3

LOCATION OF THE BUTTONS ............ 4

Control panel ............................................. 4

Remote controller ...................................... 5

Preparing the remote controller ................ 6

BASIC OPERATIONS ....................... 7

Turning on the power ................................ 7

Setting the clock ........................................ 8

RADIO OPERATIONS ...................... 9

Listening to the radio ................................. 9

Storing stations in memory ....................... 10

Tuning in to a preset station ...................... 11

SOUND ADJUSTMENTS ................... 15

Selecting preset sound modes

(C-EQ: custom equalizer) ....................... 15

Adjusting the sound .................................. 16

OTHER MAIN FUNCTIONS ................ 17

Selecting the level display ......................... 17

Detaching the control panel ...................... 18

TROUBLESHOOTING ...................... 19

MAINTENANCE ............................. 20

Handling discs ........................................... 20

SPECIFICATIONS........................... 21

CD OPERATIONS ........................... 12

Playing a CD ............................................. 12

Locating a track or a particular portion

on a CD .................................................. 13

Selecting CD playback modes .................. 14

Prohibiting CD ejection ............................. 14

How to use the M (MODE) button

If you press M (MODE), the unit goes into functions mode and the number buttons and 5/∞
buttons work as different function buttons.

ENGLISH

Ex.: When number button 2 works as MO (monaural) button.

Time countdown indicator

To use these buttons for original functions again after pressing M (MODE), wait for 5 seconds
without pressing any of these buttons until the functions mode is cleared.

• Pressing M (MODE) again also clears the functions mode.

BEFORE USE

*

For safety....

• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.

• Stop the car before performing any complicated
operations.

*

Temperature inside the car....

If you have parked the car for a long time in hot or
cold weather, wait until the temperature in the car
becomes normal before operating the unit.

3

Control panel

Display window

ENGLISH

a

LOCATION OF THE BUTTONS

s

d

f lk

ghj

1 2

1 (standby/on/attenuator) button
2 SEL (select) button
3 Control dial
4 Loading slot
5 Display window
6 FM/AM button
7 5 (up) button

+10 button

8 4 /¢ buttons
9 0 (eject) button
p DISP (display) button

• Also functions as SSM buttons when pressed
together with M (MODE) button.

q M (MODE) button

• Also functions as SSM buttons when pressed
together with DISP (display) button.

w Remote sensor
e MO (monaural) button
r Number buttons
t RPT (repeat) button
y RND (random) button
u E (EQ: equalizer) button

4 6 9

3

qp e yt

w

5

/

r u i ;

i CD button
o ∞ (down) button

–10 button

; (control panel release) button

Display window

a EQ (equalizer) indicator
s LOUD (loudness) indicator
d CD–in indicator
f CD indicator
g FM band indicators (FM1, FM2, FM3)
h AM band indicator
j Tuner reception indicators

MO (monaural), ST (stereo)

k RND (disc random) indicator
l Volume (or audio) level indicator
/ Main display
z RPT (repeat) indicator

z

87

o

4

Remote controller

S

1 • Turns on the unit if pressed when the unit

is turned off.

• Turns off the unit if pressed and held until
“SEE YOU” appears on the display.

• Drops the volume level in a moment if
pressed briefly.
Press again to resume the volume.

3 Selects the preset stations while listening to

the radio.
Each time you press the button, the preset
station number increases, and the selected
station is tuned in.

4 Selects the sound mode (C-EQ: custom

equalizer).
Each time you press the button, the sound
mode (C-EQ) changes.

5 Selects the band while listening to the radio.

Each time you press the button, the band
changes.

6 Selects the source.

Each time you press the button, the source
changes.

7 Functions the same as the control dial on the

main unit.

Note:

These buttons do not used for adjusting
“CLOCK H,” “CLOCK M,” and “LEVEL”
(see pages 8 and 17).

ENGLISH

2 • Searches for stations while listening to the

radio.

• Fast-forwards or reverses the track if
pressed and held while listening to a CD.

• Skips to the beginning of the next track or
goes back to the beginning of the current
(or previous) tracks if pressed briefly while
listening to a CD.

5

Preparing the remote
controller

3. Return the battery holder.

Insert again the battery holder by pushing it
until you hear a clicking sound.

Before using the remote controller:

ENGLISH

• Aim the remote controller directly at the remote
sensor on the main unit. Make sure there is no
obstacle in between.

Remote sensor

• Do not expose the remote sensor to strong
light (direct sunlight or artificial lighting).

Installing the battery

When the controllable range or effectiveness
of the remote controller decreases, replace
the battery.

1. Remove the battery holder.

1) Push out the battery holder in the
direction indicated by the arrow using a
ball point pen or a similar tool.

2) Remove the battery holder.

(back side)

WARNING:

• Store the battery in a place which children
cannot reach.
If a child accidentally swallows the battery,
immediately consult a doctor.

• Do not recharge, short, disassemble or heat the
battery or dispose of in a fire.
Doing any of these things may cause the battery
to give off heat, crack or start a fire.

• Do not leave the battery with other metallic
materials.
Doing this may cause the battery to give off
heat, crack or start a fire.

• When throwing away or saving the battery,
wrap in tape and insulate; otherwise, it may
cause the battery to give off heat, crack or start
a fire.

• Do not poke the battery with tweezers or similar
tools.
Doing this may cause the battery to give off
heat, crack or start a fire.

(back side)

2. Place the battery.

Slide the battery into the holder with the
+ side facing upwards so that the battery
is fixed in the holder.

6

CAUTION:

DO NOT leave the remote controller in a place
(such as dashboards) exposed to direct sunlight
for a long time. Otherwise, it may be damaged.

Lithium coin
battery (product
number: CR2025)

BASIC OPERATIONS

ENGLISH

1

3

Turning on the power

1

Turn on the power.

Note on One-Touch Operation:

When you select a source in step 2 below, the
power automatically comes on. You do not have
to press this button to turn on the power.

2

Select the source.

To operate the tuner (FM or AM),

see pages 9 – 11.

To play a CD,

see pages 12 – 14.

3

Adjust the volume.

To increase the
volume

To decrease the
volume

Volume (or audio) level indicator
(see page 17)

2

4

Adjust the sound as you want.
(See pages 15 and 16.)

To drop the volume in a moment

Press briefly while listening to any
source. “AT T” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the
button briefly again.

• If you turn the control dial, you can also restore
the sound.

To turn off the power

Press and hold for more than one
second.

“SEE YOU” appears, then the unit turns off.

• If you turn off the power while listening to a

CD, CD play will start from where playback has
been stopped previously, next time you turn on
the power.

CAUTION on Volume Setting:

CDs produce very little noise compared with other
sources. If the volume level is adjusted for the
tuner, for example, the speakers may be damaged
by the sudden increase in the output level.
Therefore, lower the volume before playing a CD
and adjust it as required during playback.

Volume level appears.

7

ENGLISH

Setting the clock

1

Press and hold SEL (select) for more
than 2 seconds.

“CLOCK H,” “CLOCK M,” or “LEVEL”
appears on the display.

2

Set the hour.

1 Select “CLOCK H” (hour) if not shown on

the display.

LEVEL

2 Adjust the hour.

2 Adjust the minute.

4

Finish the setting.

CLOCK MCLOCK H

To check the current clock time or change the
display mode

Press DISP (display) repeatedly.
Each time you press the button,
the display mode changes as
follows:

• During tuner operation:

ClockFrequency

• During CD operation:

3

Set the minute.

1 Select “CLOCK M” (minute).

8

LEVEL

ClockElapsed playing time

• During power off:

The power turns on and the clock time is

CLOCK MCLOCK H

shown for 5 seconds, then the power turns
off.

RADIO OPERATIONS

ENGLISH

Listening to the radio

You can use either automatic searching or manual
searching to tune in to a particular station.

Searching a station automatically:
Auto search

1

Select the band (FM1 – 3, AM).

Each time you press the
button, the band changes as
follows:

FM1 FM2 FM3 AM

Selected band appears.

Lights up when receiving an FM stereo
broadcast with sufficient signal strength.

Note:

This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.

2

Start searching a station.

To search stations of
higher frequencies

To stop searching before a station is
received, press the same button you have

pressed for searching.

Searching a station manually:
Manual search

1

Select the band (FM1 – 3, AM).

Each time you press the
button, the band changes as
follows:

FM1 FM2 FM3 AM

Note:

This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.

2

Press and hold ¢ or 4
until “M” (manual) starts flashing on
the display.

To search stations of
lower frequencies

When a station is received, searching stops.

CONTINUED ON THE NEXT PAGE

9