JVC KD-AHD69J, KD-HDR60J Service Manual
SERVICE MANUAL
MA468<Rev.001>20102SERVICE MANUAL
KD-AHD69J, KD-HDR60J
CD RECEIVER
COPYRIGHT © 2010 Victor Company of Japan, Limited
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)
TABLE OF CONTENTS
1 PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
2 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
3 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
4 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16
5 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22
COPYRIGHT © 2010 Victor Company of Japan, Limited
No.MA468<Rev.001>
2010/2
SPECIFICATION
AUDIO AMPLIFIER SECTION
Power Output 20 W RMS × 4 Channels at 4 Ω and < 1% THD+N
Signal-to-Noise Ratio 80 dBA (reference: 1 W into 4 Ω)
Load Impedance 4 Ω (4 Ω to 8 Ω allowance)
Equalizer Control Range Frequencies 45 Hz, 120 Hz, 315 Hz, 800 Hz, 2.4 kHz, 6.3 kHz, 15 kHz
Level ±10 dB
Frequency Response 40 Hz to 20 000 Hz
Line-Out Level/Impedance KD-AHD69 5.0 V/20kΩ load (full scale)
KD-HDR60 2.5 V/20 kΩ load (full scale)
Subwoofer-Out Level/Impedance
Output Impedance 1 kΩ
Other Terminal USB input terminal, AUX (auxiliary) input jack, Expansion port, Steering
Frequency Range FM with channel interval set to 100 kHz or 200
FM Tuner Usable Sensitivity 8.3 dBf (0.7 µV/75 Ω)
AM Tuner Sensitivity 13 µV
Type Compact disc player
Signal Detection System Non-contact optical pickup (semiconductor laser)
Number of Channels 2 channels (stereo)
Frequency Response 5 Hz to 20 000 Hz
Dynamic Range 96 dB
Signal-to-Noise Ratio 98 dB
Wow and Flutter Less than measurable limit
MP3 Decoding Format: (MPEG1/2 Audio Layer 3) Max. Bit Rate: 320 kbps
WMA (Windows Media
USB Standards USB 2.0 Full Speed
Data Transfer Rate Full Speed: Maximum 12 Mbps
Compatible Device Mass storage class
Compatible File System FAT 32/16/12
Max. Current DC 5 V 500 mA
Power Requirement Operating Voltage DC 14.4 V (11 V to 16 V allowance)
Grounding System Negative ground
Allowable Operating Temperature 0°C to +40°C (32°F to 104°F)
Dimensions (W × H × D):
(approx.)
Mass 1.3 kg (2.9 lbs) (excluding accessories)
Designs & specifications are subject to change without notice.
KD-AHD69 5.0 V/20 kΩ load (full scale)
KD-HDR60 2.5 V/20 kΩ load (full scale)
wheel remote input (only for KD-AHD69), Antenna input
TUNER SECTION (HD Radio System Compatible)
87.5 MHz to 107.9 MHz
kHz
with channel interval set to 50 kHz 87.5 MHz to 108.0 MHz
AM with channel interval set to 10 kHz 530 kHz to 1 710 kHz
with channel interval set to 9 kHz 531 kHz to 1 602 kHz
50 dB Quieting Sensitivity 14.3 dBf (1.4 µV/75 Ω)
Alternate Channel Selectivity (400 kHz)
Frequency Response 20 Hz to 20 000 Hz (HD Radio broadcast)
Stereo Separation 70 dB (HD Radio broadcast)
Capture Ratio 3.5 dB
Selectivity 80 dB
Frequency Response 40 Hz to 15 000 Hz (HD Radio broadcast)
Stereo Separation 70 dB (HD Radio broadcast)
65 dB
40 Hz to 15 000 Hz (Conventional broadcast)
50 dB (Conventional broadcast)
CD PLAYER SECTION
® Audio) Decoding Format Max. Bit Rate: 192 kbps
USB SECTION
Low Speed: Maximum 1.5 Mbps
GENERAL
Installation Size 182 mm × 52 mm × 160 mm (7-3/16” × 2-1/16” × 6-5/16”)
Panel Size 188 mm × 58 mm × 5 mm (7-7/16” × 2-5/16” × 1/4”)
1-2 (No.MA468<Rev.001>)
SECTION 1
PRECAUTION
1.1 Safety Precautions
(1) This design of this product contains special hardware and
many circuits and components specially for safety purposes. For continued protection, no changes should be made
to the original design unless authorized in writing by the
manufacturer. Replacement parts must be identical to
those used in the original circuits. Services should be performed by qualified personnel only.
(2) Alterations of the design or circuitry of the product should
not be made. Any design alterations of the product should
not be made. Any design alterations or additions will void
the manufacturers warranty and will further relieve the
manufacture of responsibility for personal injury or property
damage resulting therefrom.
(3) Many electrical and mechanical parts in the products have
special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the
protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special
safety characteristics are identified in the Parts List of Service Manual. Electrical components having such features
are identified by shading on the schematics and by ( ) on
the Parts List in the Service Manual. The use of a substitute
replacement which does not have the same safety characteristics as the recommended replacement parts shown in
the Parts List of Service Manual may create shock, fire, or
other hazards.
(4) The leads in the products are routed and dressed with ties,
clamps, tubings, barriers and the like to be separated from
live parts, high temperature parts, moving parts and/or
sharp edges for the prevention of electric shock and fire
hazard. When service is required, the original lead routing
and dress should be observed, and it should be confirmed
that they have been returned to normal, after reassembling.
(5) Leakage shock hazard testing
After reassembling the product, always perform an isolation check on the exposed metal parts of the product (antenna terminals, knobs, metal cabinet, screw heads,
headphone jack, control shafts, etc.) to be sure the product
is safe to operate without danger of electrical shock.Do not
use a line isolation transformer during this check.
• Plug the AC line cord directly into the AC outlet. Using a
"Leakage Current Tester", measure the leakage current
from each exposed metal parts of the cabinet, particularly any exposed metal part having a return path to the
chassis, to a known good earth ground. Any leakage current must not exceed 0.5mA AC (r.m.s.).
• Alternate check method
Plug the AC line cord directly into the AC outlet. Use an
AC voltmeter having, 1,000Ω per volt or more sensitivity
in the following manner. Connect a 1,500Ω 10W resistor
paralleled by a 0.15µF AC-type capacitor between an ex-
posed metal part and a known good earth ground.
Measure the AC voltage across the resistor with the AC
voltmeter.
Move the resistor connection to each exposed metal
part, particularly any exposed metal part having a return
path to the chassis, and measure the AC voltage across
the resistor. Now, reverse the plug in the AC outlet and
repeat each measurement. Voltage measured any must
not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5
mA AC (r.m.s.).
AC VOLTMETER
(Having 1000
ohms/volts,
or more sensitivity)
0.15 F AC TYPE
Place this
probe on
1500 10W
Good earth ground
1.2 Warning
(1) This equipment has been designed and manufactured to
meet international safety standards.
(2) It is the legal responsibility of the repairer to ensure that
these safety standards are maintained.
(3) Repairs must be made in accordance with the relevant
safety standards.
(4) It is essential that safety critical components are replaced
by approved parts.
(5) If mains voltage selector is provided, check setting for local
voltage.
1.3 Caution
Burrs formed during molding may be left over on some parts
of the chassis.
Therefore, pay attention to such burrs in the case of preforming repair of this system.
1.4 Critical parts for safety
In regard with component parts appearing on the silk-screen
printed side (parts side) of the PWB diagrams, the parts that are
printed over with black such as the resistor ( ), diode ( )
and ICP ( ) or identified by the " " mark nearby are critical
for safety. When replacing them, be sure to use the parts of the
same type and rating as specified by the manufacturer.
(This regulation dose not Except the J and C version)
each exposed
metal part.
(No.MA468<Rev.001>)1-3
1.5 Preventing static electricity
Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser
diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
1.5.1 Grounding to prevent damage by static electricity
Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products.
Be careful to use proper grounding in the area where repairs are being performed.
(1) Ground the workbench
Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the
traverse unit (optical pickup) on it.
(2) Ground yourself
Use an anti-static wrist strap to release any static electricity built up in your body.
(caption)
Anti-static wrist strap
1M
Conductive material
(conductive sheet) or iron palate
(3) Handling the optical pickup
• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical
pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)
• Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily
destroy the laser diode.
1.6 Handling the traverse unit (optical pickup)
(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.
(2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the
replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a
time when attaching it to the connector.
(3) Handle the flexible cable carefully as it may break when subjected to strong force.
(4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.
1-4 (No.MA468<Rev.001>)
1.7 Attention when traverse unit is decomposed
*Please refer to "Disassembly method" in the text for the pickup unit.
• Apply solder to the short land sections before the card wire is disconnected from the connector on the servo board. (If the card wire
is disconnected without applying solder, the pickup may be destroyed by static electricity.)
• In the assembly, be sure to remove solder from the short land sections after connecting the card wire.
Mechanism control board
CN102
Flexible wire
Short land section
Pickup
(No.MA468<Rev.001>)1-5
1.8 Important for laser products
1.CLASS 1 LASER PRODUCT
2.CAUTION :
(For U.S.A.) Visible and/or invisible class II laser radiation
when open. Do not stare into beam.
(Others) Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
3.CAUTION : Visible and/or invisible laser radiation when
open and inter lock failed or defeated. Avoid direct
exposure to beam.
4.CAUTION : This laser product uses visible and/or invisible
laser radiation and is equipped with safety switches which
prevent emission of radiation when the drawer is open and
the safety interlocks have failed or are defeated. It is
dangerous to defeat the safety switches.
5.CAUTION : If safety switches malfunction, the laser is able
to function.
6.CAUTION : Use of controls, adjustments or performance of
procedures other than those specified here in may result in
hazardous radiation exposure.
!
Please use enough caution not to
see the beam directly or touch it
in case of an adjustment or operation
check.
REPRODUCTION AND POSITION OF LABELS and PRINT
WARNING LABEL and PRINT
1-6 (No.MA468<Rev.001>)
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.
(No.MA468<Rev.001>)1-7
SECTION 3
DISASSEMBLY
3.1 Main body
3.1.1 Removing the Bottom chassis (See Fig.1)
(1) Remove the two screws A and one screw B attaching the
Heat sink.
(2) Remove the one screws C and one screw D attaching the
Bottom chassis.
ABCD A
Fig.1
3.1.2 Removing the Front chassis (See Fig.2)
(1) Disengage hour hooks a engaged Front chassis.
hook
a
Fig.2
3.1.3 Removing the Main board (see Fig.3, 4, 5)
(1) Remove the one screw E attaching the Top chassis. (See
Fig.3)
(3) Remove the three screws H attaching the Main board. (See
Fig.5)
(4) Disconnect the B-B connector connected CD mechanism
and Main board CN481
CN481
of the Main board. (See Fig.5)
H
Fig.5
3.1.4 Removing the CD mechanism (See Fig.6)
(1) Remove the three screws J attaching the CD mechanism.
H
J
E
Fig.3
(2) Remove the two screws F and one screw G attaching the
Side plate. (See Fig.4)
FG F
Fig.4
J
Fig.6
3.1.5 Removing the Switch board (See Fig.7)
(1) Remove the Volume knob.
(2) Remove the four screws K attaching the Rear cover.
(3) Disengage eleven hooks b engaged Rear cover.
hook b
hook b
KK
Fig.7
1-8 (No.MA468<Rev.001>)
3.2 CD MECHANISM assembly section
• Remove the CD MECHANISM assembly from the main body.
Removing the MECHANISM CONTROL BOARD
3.2.1
1
assembly (See Fig.
(1)
From the bottom side of CD MECHANISM assembly,
remove the solders from the soldered sections (
c
) on the MECHANISM CONTROL BOARD assembly.
(See Fig.
(2) Remove the three screws A attaching the MECHANISM
CONTROL BOARD assembly. (See Fig.1.)
(3) Solder the short land sections on the pickup. (See Fig.2.)
Caution:
• Solder the short land sections on the pickup before
•
1
.)
disconnecting the flexible wire from the connector
on the MECHANISM CONTROL BOARD as-
CN102
sembly.
If the card wire is disconnected without attaching
solder, the pickup may be destroyed by static
electricity. (See Fig.2.)
When attaching the MECHANISM CONTROL
BOARD assembly, remove the solders from the
short land sections after connecting the flexible
wire to the connector CN102
CONTROL BOARD assembly.
and 2)
a, b
and
on the MECHANISM
Mechanism
a
b
control board
CN102
A
A
c
A
Fig.1
Mechanism control board
CN102
Flexible wire
Short land section
Pickup
Fig.2
(No.MA468<Rev.001>)1-9
3.2.2 Removing the top cover (See Fig.3 to 5)
• Remove the MECHANISM CONTROL BOARD assembly.
(1) From the front side of the CD MECHANISM assembly,
change the hook position of the two roller springs. (See
Fig.3.)
(2) From the side of the CD MECHANISM assembly, remove
the six screws B attaching the top cover. (See Fig.3 and 4.)
(3) Take out the top cover in an upward direction. (See Fig.5.)
Top cover
B
Roller spring Roller spring
Fig.3
Top cover
Top cover
Fig.5
3.2.3 Removing the roller (See Fig.6)
• Remove the MECHANISM CONTROL BOARD assembly and
top cover.
(1) From the bottom side of the top cover, remove the screw C
attaching the gear holder.
(2) Remove the R.holder assembly from disc plate, and then
take out the roller from R.holder assembly in the direction
of the arrow.
Reference:
When attaching the R.ACT gear (2) and R.ACT gear (3),
apply grease to the section d of R.holder assembly.
Roller coller
B
B
Fig.4
1-10 (No.MA468<Rev.001>)
Gear holder
Roller gear
R.ACT gear(3)
R.ACT gear(2)
Top cover
C
d
R.holder assembly
Fig.6
Washer
Roller
Disc plate
3.2.4 Removing the PHOTO BOARD assembly (See Fig.7
and 8)
• Remove the MECHANISM CONTROL BOARD assembly and
top cover.
From the bottom side of the top cover, release the
(1)
projection
7
Fig.
(2) Take out the disc plate in the direction of the arrow. (See
Fig.7.)
(3) From the reverse side of the disc plate, remove the screw
D attaching the PHOTO BOARD assembly. (See Fig.8.)
e
from the notch of the disc plate. (See
.)
e
e
SUS
spring
Mechanism section
Mecha frame
SUS
spring
E
Top cover
Fig.7
Disc plate
D
Photo board
Disc plate
Fig.8
3.2.5 Removing the mechanism section (See Fig.9 and 10)
• Remove the MECHANISM CONTROL BOARD assembly and
top cover.
(1)
From the top side of the CD MECHANISM assembly,
remove the two screws
assembly. (See Fig.
(2) Remove the two roller springs on the top side of the mecha
frame. (See Fig.9.)
(3) Remove the four SUS springs on the top side of the mecha
frame. (See Fig.9.)
(4) Remove the link spring on the top side of the mecha frame.
(See Fig.10.)
(5) Release section f of the three dampers from the mecha
frame. (See Fig.10.)
Reference:
When attaching the roller spring and SUS spring, keep
direction before remove.
Move the slide cam (R) assembly in the direction of the
(6)
arrow, and then take out the mechanism section in an
upward direction. (See Fig.
Reference:
When attaching the mechanism section, apply grease to
the section g. (See Fig.10.)
E
attaching the loading motor
9
.)
10.)
SUS
spring
Roller spring
Loading motor assembly
Fig.9
F
Cam cover
Mecha frame
Fig.10
SUS
spring
(No.MA468<Rev.001>)1-11
3.2.6 Removing the slide cam (L) (See Fig.11 to 13)
• Remove the MECHANISM CONTROL BOARD assembly, top
cover and mechanism section.
(1) From the top side of the mecha frame, remove the screw F
attaching the cam cover. (See Fig.11.)
Take out the cam cover from mecha frame in an upward
(2)
11
F
.)
Cam cover
direction. (See Fig.
(3) Take out the slide cam (L) in the direction of the arrow.
(See Fig.12.)
Reference:
When attaching the slide cam (L), apply grease to the
section h. (See Fig.13.)
Slide cam(L)
Mecha frame
Fig.12
h
Slide cam(L)
h
Mecha frame
Fig.11
h
h
Slide cam(L)
h
Fig.13
h
h
h
1-12 (No.MA468<Rev.001>)
3.2.7 Removing the F.lock lever and slide cam (R) (See
Fig.14 and 15)
• Remove the MECHANISM CONTROL BOARD assembly, top
cover and mechanism section.
(1) From the top side of the mecha frame, take out the slide
cam (R) assembly in an upward direction. (See Fig.14.)
(2) Rotate the F.lock lever in the direction of the arrow 1, and
then take out the direction of the arrow 2. (See Fig.14.)
Reference:
When attaching the slide cam (R) assembly, the f.lock
lever and the link arm apply grease to the section
14
(See Fig.
and 15.)
h
Slide cam(R) assembly
h
F.lock lever
2
1
h
h
3.2.8 Removing the damper (See Fig.16)
• Remove the MECHANISM CONTROL BOARD assembly, top
cover and mechanism section.
From the mechanism section, pull out the three dampers in the
direction of the arrow.
Reference:
Before inserting the shaft to the dampers, apply IPA to the
pocket j of damper.
.
Damper (Gray)
Damper (Brown)
j
j
Damper (Brown)
j
Fig.16
Mecha frame
h
h
h
h
Link arm
Fig.14
Slide cam(R) assembly
h
h
h
Slide cam(R) assembly
Fig.15
3.2.9 Removing the clamper assembly (See Fig.17)
• Remove the MECHANISM CONTROL BOARD assembly, top
h
cover and mechanism section.
(1) From the top side of the mechanism section, release the
clamper spring.
(2) Move the clamper assembly in the direction of the arrow,
and then release the joints (k and m).
Take out the clamper assembly from the T.M chassis
(3)
assembly.
h
Clamper assembly
Clamper spring
k
T.M. chassis assembly
m
Fig.17
(No.MA468<Rev.001>)1-13
3.2.10 Removing the feed motor (See Fig.18 and 19)
r
• Remove the MECHANISM CONTROL BOARD assembly, top
cover, mechanism section and clamper assembly.
(1) From the bottom side of the T.M chassis assembly, remove
the two screws G attaching the feed motor assembly. (See
Fig.18.)
Remove the two screws H attaching the feed motor to
(2)
19
f.motor holder. (See Fig.
Reference:
When attaching the f. wheel gear, trigger arm and feed
motor, apply grease to the sections (n, p and q). (See
Fig.18 and 19.)
.)
Feed motor
F.worm gear
q
Comp. spring
H
3.2.11 Removing the SWITCH BOARD assembly (See
Fig.18)
• Remove the MECHANISM CONTROL BOARD assembly, top
cover, mechanism section, clamper assembly and feed motor
assembly.
From the bottom side of the T.M chassis assembly, take out
the SWITCH BOARD assembly in an upward direction from
T.M chassis assembly.
G
Feed motor assembly
Switch board
p
n
F.wheel gear
Trigger arm
F.motor holder
Fig.19
3.2.12 Removing the loading motor (See Fig.20)
• Remove the MECHANISM CONTROL BOARD assembly, top
cover, mechanism section and clamper assembly.
(1) From the right side of the L.M base assembly, remove the
two screws J attaching the loading motor.
(2) Take out the loading motor in the direction of the arrow
from the L.M base assembly.
Reference:
When attaching the loading motor, apply grease to the
section r.
J
r
L.M. base assembly
Fig.20
L.worm gear
Loading moto
T.M. chassis assembly
Fig.18
1-14 (No.MA468<Rev.001>)
3.2.13 Removing the pickup assembly (See Fig.21 to 22)
• Remove the MECHANISM CONTROL BOARD assembly, top
cover, mechanism section, clamper assembly and feed motor
assembly.
Caution:
• Do not touch section u on the pickup assembly. (See Fig.21
and 22.)
(1) From the bottom side of the T.M chassis assembly, move
the pickup assembly in the direction of the arrow from the
T.M chassis assembly. (See Fig.21.)
(2) Pull out the main shaft. (See Fig.21.)
(3) Remove the screw K attaching the pickup to the rack plate.
(See Fig.22.)
Reference:
When attaching the loading motor, apply grease to the
sections s and t. (See Fig.21.)
3.2.14 Removing the spindle motor (See Fig.23 and 24)
Remove the MECHANISM CONTROL BOARD assembly,
•
top cover, mechanism section, clamper assembly, feed motor
assembly and pickup assembly.
(1) From the top side of the T.M chassis assembly, remove the
CD T.table assembly from the spindle motor. (See Fig.23.)
(2) Remove the two screws L attaching the spindle motor.
(See Fig.23.)
(3) Take out the spindle motor from the bottom side of the T.M
chassis assembly. (See Fig.23.)
Reference:
When attaching the CD T.table assembly to the spindle
motor shaft, apply loctite 460 to inside the CD T.table
assembly. (See Fig.24.)
Pick up assembly
s
T.M. chassis assembly
u
Fig.21
t
Main shaft
LL
Spindle motor
Fig.23
CD T.table assembly
CD T.table assembly
T.M.chassis assembly
Loctite
K
Rack plate
u
Pick up
Fig.22
Spindle motor
Fig.24
(No.MA468<Rev.001>)1-15
SECTION 4
ADJUSTMENT
4.1 Test instruments required for adjustment
(1) Digital oscilloscope (100MHz)
(2) Digital tester
(3) Test Disc JVC :CTS-1000
(4) Extension cable for check
EXTSH002-22P x 1
4.2 Standard measuring conditions
Power supply voltage DC14.4V(10.5 to 16V)
Load impedance 20K.(2 Speakers connection)
Output Level Line out 2.5V (Vol. MAX)
4.5 How to connect the extension cable for adjusting
Caution:
Be sure to attach the heat sink and rear bracket onto the power amplifier IC and regulator IC respectively, before supply
the power.
If voltage is applied without attaching these parts, the power amplifier IC and regulator IC will be destroyed by heat.
4.3 Standard volume position
Balance and Bass &Treble volume : lndication"0"
Loudness : OFF
4.4 Dummy load
Exclusive dummy load should be used for AM,and FM.
For FM dummy load, there is a loss of 6dB between SSG
outputand antenna input.
The loss of 6dB need not be considered sincedirect reading offigures are applied in this working standard.
Extension cable
EXTSH002-22P
1-16 (No.MA468<Rev.001>)
4.6 SERVICE MODE
4.6.1 Service mode setting
(1) Push POWER BUTTON (Power ON)
(2) Set to service mode
Keep this state more 3 seconds while continuing pressing the [MENU] button and [DISC DOWN] button scquentially.
*Exchanging of operate a menu of a service mode with the [FF] button and [REW] button.
Operate choice of a menu with a [ENT] button.
SERVICE MODE
DATA DELETE
INIT ALL
Initialize EEPROM data
CDERR DEL
CHERR DEL
Clear CD error history
Clear changer error history
: The error history saved in the CD changer is cleared.
DSPERR DEL
Clear DSP error history
Note : A disc is inseted, and it is displayed only at the timer of CD function.
RUNNING
MODE 1 For use in running tests
MODE 2
For use in running tests
CDLD ON xx yy zz CD laser illumination and electric current (mA)
xx : Early current value
yy : Current current value
zz : Difference value
TUBUYAKI Only the factory setup. No use.
ERROR READ
CD ERROR
CH ERROR
Read CD error history
Read CD changer error history
: The error history saved on the CD changer is read out.
DSP ERROR
Read DSP error history
ROMVERxx ROM correction versionROM CORRE
(No.MA468<Rev.001>)1-17
AUTO ADJ
Only factory setup. No use.TUNER ADJ
MANUAL ADJ
ADJ1
1. FM DAA
87.5 40dBuV 0%
Press OK
ADJ2
2. FM DAA
97.9 40dBuV 0%
Press OK
ADJ3
3. FM DAA
108.0 40dBuV 0%
Press OK
ADJ4
4. FM S Meter
97.9 30dBuV 0%
Press OK
ADJ5
5. FM S Meter
97.9 60dBuV 0%
Press OK
ADJ6
6. FM Full Sepa
97.9 70dBuV 0%
Lch Press OK
ADJ7
7. FM IF Counter
97.9 70dBuV 0%
Press OK
ADJ8
8. AM S Meter
999 26dBuV 0%
Press OK
ADJ9
9. AM S Meter
999 56dBuV 0%
Press OK
ADJ10
10. AM IF Counter
999 56dBuV 0%
Press OK
1. FM DAA
87.5 40dBuV 0%
No signal
2. FM DAA
97.9 40dBuV 0%
No signal
3. FM DAA
108.0 40dBuV 0%
No signal
4. FM S Meter
97.9 30dBuV 0%
High or Low or No signal
5. FM S Meter
97.9 60dBuV 0%
High or Low or No signal
6. FM Full Sepa
97.9 60dBuV 0%
Adjust NG or No signal
7. FM IF Counter
97.9 60dBuV 0%
Adjust NG or No signal
8. FM IF Counter
999 26dBuV 0%
High or Low or No signal
9. AM S Meter
999 56dBuV 0%
High or Low or No signal
10. AM IF Counter
999 56dBuV 0%
Adjust NG or No signal
1-18 (No.MA468<Rev.001>)
Manual Adjust
COMPLETED
POWER
POWER OFF
(Adjust Mode FINISH)
Loading...