JVC KD-G420 Diagram

MA232200511

SERVICE MANUAL

CD RECEIVER

KD-AR470,KD-G420,KD-G521,

KD-G524,KD-G525,KD-G527

KD-AR470,KD-G420

Area suffix

J ------------- Northern America

KD-AR470

KD-G521

KD-G525

Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)

KD-G420

KD-G524

KD-G527

Area suffix

E ------------- Southern Europe EX ------------ Northern Europe EY ------------- Eastern Europe EU ------------------------- Turkey

Area suffix

UI ---------------------------- India

Area suffix

UT ------------------------- Taiwan UH ---------------------- Thailand UN --------------------- Indonesia U -------------------- Other Areas

Area suffix

EE -------- Russian Federation

TABLE OF CONTENTS

1 PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

2 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

3 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

4 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

5 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14

KD-G521

KD-G524

KD-G525

KD-G527

No.MA232

2005/11

SPECIFICATION

AUDIO AMPLIFIER SECTION

Power Output KD-AR470, KD-G420 20 W RMS Maximum Power Output KD-G521, KD-G524,

KD-G525, KD-G527

Continuous Power Output (RMS)

Signal to Noise Ratio KD-AR470, KD-G420 80 dBA (reference: 1 W into 4

Load Impedance 4 Tone Control Range Bass ±10 dB at 100 Hz

Frequency Response 40 Hz to 20 000 Hz Line-Out Level/Impedance KD-AR470 4.0 V/20 k

Output Impedance 1 k Other Terminals CD changer, Steering wheel remote input ( Only KD-G521 ), AUX (auxiliary)

Frequency Range FM ( KD-AR470, KD-G420 ) 87.5 MHz to 107.9 MHz (with channel interval set to 100 kHz or 200 kHz)

FM Tuner Usable Sensitivity 11.3 dBf (1.0

AM Tuner KD-AR470, KD-G420,

MW Tuner KD-G521, KD-G527 Sensitivity 20

LW Tuner KD-G521, KD-G527 Sensitivity 50

Type Compact disc player Signal Detection System Non-contact optical pickup (semiconductor laser) Number of Channels 2 channels (stereo) Frequency Response 5 Hz to 20 000 Hz Dynamic Range 96 dB Signal-to-Noise Ratio 98 dB Wow and Flutter Less than measurable limit MP3 Decoding Format MPEG1/2 Audio Layer 3

WMA (Windows Media® Audio) Decoding Format Max. Bit Rate: 192 kbps

Power Requirement Operating Voltage DC 14.4 V (11 V to 16 V allowance) Grounding System Negative ground Allowable Operating Temperature 0 Dimensions (W

Mass (approx.) 1.5 kg (3.3 lbs) (excluding accessories)

• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

× H × D) Installation Size (approx.) 182 mm × 52 mm × 150 mm (7-3/16" × 2-1/16" × 5-15/16")

KD-G521, KD-G524, KD-G525, KD-G527

KD-G521, KD-G524, KD-G525, KD-G527 70 dB

Treble ±10 dB at 10 kHz

KD-G420, KD-G521, KD-G524, KD-G525, KD-G527

FM ( KD-G521, KD-G524, KD-G525 ) 87.5 MHz to 108.0 MHz FM1/FM2 ( KD-G527 ) 87.5 MHz to 108.0 MHz FM3 ( KD-G527 ) 65.00 MHz to 74.00 MHz AM ( KD-AR470, KD-G420 ) 530 kHz to 1 710 kHz (with channel interval set to 10 kHz)

AM ( KD-G521, KD-G527 ) (MW) 522 kHz to 1 620 kHz

AM ( KD-G524, KD-G525 ) 531 kHz to 1 602 kHz

50 dB Quieting Sensitivity 16.3 dBf (1.8 Alternate Channel Selectivity (400 kHz) 65 dB Frequency Response 40 Hz to 15 000 Hz Stereo Separation 35 dB Capture Ratio 1.5 dB

KD-G524, KD-G525

Panel Size (approx.) 188 mm

Front 50 W per channel Rear 50 W per channel Front 19 W per channel into 4

harmonic distortion.

Rear 19 W per channel into 4

harmonic distortion.

Ω (4 Ω to 8 Ω allowance)

2.5 V/20 k

Ω

input jack

TUNER SECTION

87.5 MHz to 108.0 MHz (with channel interval set to 50 kHz)

531 kHz to 1 602 kHz (with channel interval set to 9 kHz)

(LW) 144 kHz to 279 kHz

Sensitivity 20 Selectivity 35 dB

µV µV

Selectivity 35 dB

CD PLAYER SECTION

Max. Bit Rate: 320 kbps

GENERAL

°C to +40°C (32°F to 104°F)

• Design and specifications are subject to change without notice.

× 4 Channels at 4 Ω and [< or =] 1% THD+N

Ω, 40 Hz to 20 000 Hz at no more than 0.8% total Ω, 40 Hz to 20 000 Hz at no more than 0.8% total

Ω)

Ω load (full scale) Ω load (full scale)

µV/75 Ω) µV/75 Ω)

µV

× 58 mm × 11 mm (7-7/16" × 2-5/16" × 7/16")

1-2 (No.MA232)

1.1 Safety Precautions

SECTION 1

PRECAUTIONS

Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.

Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.

(No.MA232)1-3

1.2 Preventing static electricity

Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.

1.2.1 Grounding to prevent damage by static electricity

Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players. Be careful to use proper grounding in the area where repairs are being performed.

(1) Ground the workbench

Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the traverse unit (optical pickup) on it.

(2) Ground yourself

Use an anti-static wrist strap to release any static electricity built up in your body.

(caption) Anti-static wrist strap

Conductive material (conductive sheet) or iron plate

(3) Handling the optical pickup

• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.)

• Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily destroy the laser diode.

1.3 Handling the traverse unit (optical pickup)

(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. (2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the

replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a

time when attaching it to the connector. (3) Handle the flexible cable carefully as it may break when subjected to strong force. (4) It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.

1.4 Attention when traverse unit is decomposed

*Please refer to "Disassembly method" in the text for the CD pickup unit.

• Apply solder to the short land before the flexible wire is disconnected from the connector on the CD pickup unit. (If the flexible wire is disconnected without applying solder, the CD pickup may be destroyed by static electricity.)

• In the assembly, be sure to remove solder from the short land after connecting the flexible wire.

Short-circuit point

(Soldering)

Flexible wire

1-4 (No.MA232)

Short-circuit point

Pickup

1.5 Important for laser products

1.CLASS 1 LASER PRODUCT

2.DANGER : Invisible laser radiation when open and inter

lock failed or defeated. Avoid direct exposure to beam.

3.CAUTION : There are no serviceable parts inside the

Laser Unit. Do not disassemble the Laser Unit. Replace

the complete Laser Unit if it malfunctions.

4.CAUTION : The CD,MD and DVD player uses invisible

laser radiation and is equipped with safety switches which

prevent emission of radiation when the drawer is open and

the safety interlocks have failed or are defeated. It is

dangerous to defeat the safety switches.

5.CAUTION : If safety switches malfunction, the laser is able

to function.

6.CAUTION : Use of controls, adjustments or performance of

procedures other than those specified here in may result in

hazardous radiation exposure.

Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.

REPRODUCTION AND POSITION OF LABELS

WARNING LABEL

CAUTION : Visible and Invisible

CLASS 1 LASER PRODUCT

laser radiation when open and interlock failed or defeated. AVOID DIRECT EXPOSURE TO BEAM. (e)

ADVARSEL : Synlig og usynlig laserstråling når maskinen er åben eller interlocken fejeler. Undgå direkte eksponering til stråling. (d)

VARNING : Synlig och osynling laserstrålning när den öppnas och spärren är urkopplad. Betrakta ej strålen. (s)

VARO : Avattaessa ja suojalukitus ohitettuna tai viallisena olet alttiina näkyvälle ja näkymättömälle lasersäteilylle. Vältä säteen kohdistumista suoraan itseesi. (f)

(No.MA232)1-5

SECTION 2

SPECIFIC SERVICE INSTRUCTIONS

2.1 Difference point

[KD-AR470, KD-G420, KD-G524 and KD-G525]

KD-AR470 KD-G420/KD-G524/KD-G525

Remote controller YES NO

Telephone Muting YES NO

Line Out Level / Impedance 4.0V / 20kohm load 2.5V / 20kohm load

[KD-G521, KD-G527]

KD-G521 KD-G527

Steering wheel remote input YES NO

2.2 CD mechanism

For Cd mechanism, please refer mechanism amnual No. MY001.

1-6 (No.MA232)

SECTION 3

DISASSEMBLY

3.1 Main body section

3.1.1 Removing the front panel assembly (See Fig.1)

(1) Push the control panel release button in the lower left part

of the front panel assembly and remove the front panel assembly.

(2) Take out the front panel assembly.

3.1.2 Removing the bottom cover (See Fig.2)

(1) Turn the main body up side down. (2) Insert a screwdriver under the joints to release the joints a

on the left side, joints b on the right side and joint c on the back side of the main body, then remove the bottom cover from the main body.

Caution:

When releasing the joints using a screwdriver, do not damage the main board.

Front panel assembly

Control panel release button

Fig.1

Bottom cover

Fig.2

(No.MA232)1-7

3.1.3 Removing the front chassis assembly (See Figs.3 and 4)

• Remove the front panel assembly and bottom cover.

(1) Remove the two screws A on the front side of the main

body. (See Fig.3)

(2) Remove the two screws B on the both sides of the main

body. (See Fig.4)

(3) Release the joints d and joints e on the both sides of the

main body, then remove the front chassis assembly toward the front. (See Fig.4)

Front chassis assembly

Fig.3

3.1.4 Removing the side panel (See Fig.5)

Reference:

Remove the front panel assembly as required. (1) Remove the two screws C and screw D attaching the side

panel on the left side of the main body.

(2) Take out the side panel from the main body.

CCD

Front chassis assembly

Fig.4

1-8 (No.MA232)

Side panel

Fig.5

3.1.5 Removing the rear bracket

(See Fig.6) [For KD-AR470, KD-G420, KD-G524 and KD-G525]

• Remove the bottom cover.

(1) Remove the three screws E, three screws F and three

screws G attaching the rear bracket on the back side of the main body.

(2) Take out the rear bracket.

3.1.6 Removing the rear bracket

(See Fig.6) [For KD-G521 and KD-G527]

• Remove the bottom cover.

(1) Remove the three screws E, three screws F and screw G

attaching the rear bracket on the back side of the main body.

(2) Remove the screw H attaching the steering remote cable

on the rear bracket. [KD-G521 only]

(3) Take out the rear bracket.

3.1.7 Removing the main board

(See Figs.6 and 7)

• Remove the front panel assembly, bottom cover, front chassis

assembly and side panel. (1) Remove the three screws E attaching the rear bracket on

the back side of the main body. (See Fig.6.)

(2) Remove the two screws J attaching the main board. (See

Fig.7.)

(3) Disconnect the connector CN101

board. (See Fig.7.)

Reference:

Remove the rear bracket as required.

and take out the main

[For KD-AR470, KD-G420, KD-G524 and KD-G525]

Rear bracket

GFG

E E

[For KD-G521 and KD-G527]

Rear bracket

Steering remote cable [KD-G521 only]

Fig.6

[For KD-AR470, KD-G420, KD-G524 and KD-G525]

CN101

Main board

Rear bracket

[For KD-G521 and KD-G527]

CN501

Main board

Rear bracket

Fig.7

(No.MA232)1-9

3.1.8 Removing the CD mechanism control board (See Fig.8) [For KD-AR470, KD-G420, KD-G524 and KD-G525]

• Remove the front panel assembly, bottom cover, front chassis

assembly, side panel and main board. (1) Disconnect the card wire from the connector CN601

CD mechanism control board.

(2) Remove the five screws K attaching the CD mechanism

control board.

(3) Remove the joint f an upward direction and remove the

joint g in the direction of the arrow.

3.1.9 Removing the CD mechanism assembly (See Fig.9)

• Remove the front panel assembly, bottom cover, front chassis

assembly, side panel, main board and CD mechanism control board. (1) Remove the three screws M attaching the top chassis. (2) Take out the CD mechanism assembly.

on the

CN601

CD mechanism control board

Fig.8

1-10 (No.MA232)

CD mechanism assembly

Top chassis

Fig.9

3.1.10 Removing the switch board

(See Figs.10 to 12)

• Remove the front panel assembly.

(1) Remove the five screws N attaching the front panel assem-

bly. (See Fig.10)

(2) Release the ten joints h and take out the rear cover. (See

Fig.11)

(3) Lift the switch board from the front panel assembly little by

little and take out the switch board. (See Fig.12)

Reference:

The volume knob is removed from the front side simultaneously.

Note:

When removing the rear cover assembly and switch board, be careful not to lose the compression spring and comp. spring. (See Fig.12)

Rear cover

Fig.10

Compression spring

Front panel assembly

Rear cover

Fig.11

Fig.12

Switch board

Comp. spring

(No.MA232)1-11

SECTION 4

ADJUSTMENT

4.1 Adjustment method

 Test instruments required for adjustment

(1) Digital oscilloscope (100MHz) (2) Electric voltmeter (3) Digital tester (4) Tracking offset meter (5) Test Disc JVC :CTS-1000 (6) Extension cable for check

EXTSH002-22P × 1

 Standard volume position

Balance and Bass &Treble volume : lndication"0" Loudness : OFF

 How to connect the extension cable for adjusting

[For KD-AR470, KD-G420, KD-G524 and KD-G525]

Caution:

Be sure to attach the heat sink and rear bracket onto the power amplifier IC and regulator IC respectively, before supply the power. If voltage is applied without attaching these parts, the power amplifier IC and regulator IC will be destroyed by heat.

 Standard measuring conditions

Power supply voltage DC14.4V(11 to 16V)

Load impedance 20KΩ(2 Speakers connection)

Output Level

KD-ARxxx Line out 4.0V (Vol. MAX)

KD-Gxxx Line out 2.5V (Vol. MAX)

 Dummy load

Exclusive dummy load should be used for AM,and FM. For FM dummy load,there is a loss of 6dB between SSG output and antenna input.The loss of 6dB need not be considered since direct reading of figures are applied in this working standard.

Extension cable: EXTSH002-22P

Side panel

CN101

Rear bracket

1-12 (No.MA232)

 How to connect the extension cable for adjusting

[For KD-G521 and KD-G527]

Caution:

EXTSH002-22P

Extension cable

Side panel

CN501

Rear bracket

(No.MA232)1-13

SECTION 5

TROUBLESHOOTING

5.1 Trouble shooting (For KD-AR470, KD-G420, KD-G524 and KD-G525)

5.1.1 Feed section

Is 4V present at both sides of the feed motor?

Is the voltage output at pin 17 and pin 18 of IC681?

Is the voltage input at pin 24 of IC681?

Is the voltage output at pin 40 of IC621?

Is the power supply present at pin 6, pin 15, pin 25, pin 39, pin 43, pin 51 and pin 64 of IC621?

Check the connections of CD8V power supply.

5.1.2 Focus section

YES

Check the feed motor.

Check the connections

YES

between the feed motor and IC681.

Is the power supply

YES YES

present at pin 10, pin 19 and pin 28 of IC681?

Check the connections of CD8V power supply.

Check the connections

YES

between IC621 and IC681.

YES

Check IC621.

Check IC681.

When the lens is moving:

Does the S-search waveform appear at IC681 pins 13 and 14?

Is the voltage input at pin 1 of IC681?

Is the voltage output at pin 33 of IC621?

Is the power supply present at pin 6, pin 15, pin 25, pin 39, pin 43, pin 51 and pin 64 of IC621?

Check the connections of CD8V power supply.

YES

Check the pickup and its connections.

Is the power supply

YES

present at pin 10, pin 19 and pin 28 of IC681?

Check the connections of CD8V power supply.

Check the connections

YES

between IC621 and IC681.

YES

Check IC621.

YES

Check IC681.

1-14 (No.MA232)

5.1.3 Spindle section

Is the disk rotated?

Is the voltage output at pin 15 and pin 15 of IC681?

Is the voltage input at pin 26 of IC681?

Is the voltage output at pin 41 of IC621?

Is the power supply present at pin 6, pin 15, pin 25, pin 39, pin 43, pin 51 and pin 64 of IC621?

YES

Does the RF signal appear at RF output of IC601?

YES

Check the spindle motor and its wiring.

Is the power supply

YES

present at pin 10, pin 19 and pin 28 of IC681?

Check the connections of CD8V power supply.

Check the connections

YES

between IC621 and IC681.

YES

Check IC621.

YES

Is the RF waveform at TP RF distorted?

Check the circuits in the vicinity of IC601 or the pickup.

YES

Check IC681.

NONO

YES

Proceed to the Tracking section

Check the connections of CD8V power supply.

5.1.4 Tracking section

When the disc is rotated at first:

Approx. 1.2V

Is the tracking error signal output at pin 11 of IC601?

Check the circuits in IC601 or the vicinity of IC601.

Replace IC601 or repair the malfunction connection point

YES

Check IC621.

YES

Check the pickup and its connections.

(No.MA232)1-15

5.1.5 Signal processing section

Is the sound output from

YES

both channels (L, R)?

Normal

No sound from either channel.

Compare the L-ch and R-ch to locate the defective point.

YES

Is 9V present at pin 36 of IC161?

Is 9V present at pin 10 of IC901?

Check IC901 and its peripheral circuits.

Is the audio signal (including sampling

YES YES

output components) output to pins 1 and 7 of IC572 during playback?

Check IC572 and its peripheral circuits.

Check the connections

YES

between pin 36 of IC161 and pin 10 of IC901.

Is the audio signal output at pin 19 and pin 20 of IC161 during playback?

Check IC161 and its peripheral circuits.

YES

Check the power amplifier IC301.

1-16 (No.MA232)

5.2 Trouble shooting (For KD-G521 and KD-G527)

5.2.1 Feed section

Is 4V present at both

YES

sides of the feed motor?

Is the voltage output at

YES

pin 4 and pin 5 of IC501?

Is the voltage input at pin

YES YES

27 of IC501?

Is the voltage output at pin

YES

40 of IC541?

Is the power supply present at pin 6, pin 15,

YES

pin 25, pin 39, pin 43, pin 51 and pin 64 of IC541?

Check the feed motor.

Check the connections between the feed motor and IC501.

Is the power supply present at pin 3, pin 12 and pin 21 of IC501?

Check the connections of CD8V power supply.

Check the connections between IC501 and IC541.

Check IC541.

Check IC501.

5.2.2 Focus section

Check the connections of CD8V power supply.

When the lens is moving:

Does the S-search waveform appear at IC501 pins 8 and 9?

Is the voltage input at pin 15 of IC501?

Is the voltage output at pin 33 of IC541?

Is the power supply present at pin 6, pin 15, pin 25, pin 39, pin 43, pin 51 and pin 64 of IC541?

YES

Check the pickup and its connections.

Is the power supply

YES

present at pin 3, pin 12 and pin 21 of IC501?

Check the connections of CD8V power supply.

Check the connections

YES

between IC501 and IC541.

YES

Check IC541.

YES

Check IC501.

Check the connections of CD8V power supply.

(No.MA232)1-17

5.2.3 Spindle section

Is the disk rotated?

Is the voltage output at pin 6 and pin 7 of IC501?

Is the voltage input at pin 17 of IC501?

Is the voltage output at pin 41 of IC541?

Is the power supply present at pin 6, pin 15, pin 25, pin 39, pin 43, pin 51 and pin 64 of IC541?

YES

Does the RF signal appear at TP RF?

YES

Check the spindle motor and its wiring.

Is the power supply

YES

present at pin 3, pin 12 and pin 21 of IC501?

Check the connections of CD8V power supply.

Check the connections

YES

between IC501 and IC541.

YES

Check IC541.

YES

Is the RF waveform at TP RF distorted?

Check the circuits in the vicinity of IC601 or the pickup.

YES

Check IC501.

NONO

YES

Proceed to the Tracking section

Check the connections of CD8V power supply.

5.2.4 Tracking section

When the disc is rotated at first:

Approx. 1.2V

Is the tracking error signal output at pin 11 of IC521?

Check the circuits in IC521 or the vicinity of IC521.

Replace IC521 or repair the malfunction connection point

YES

Check IC521.

YES

Check the pickup and its connections.

1-18 (No.MA232)

5.2.5 Signal processing section

Is the sound output from

YES

both channels (L, R)?

Normal

No sound from either channel.

Compare the L-ch and R-ch to locate the defective point.

YES

Is 9V present at pin 26 of IC161?

Is 9V present at pin 10 of IC901?

Check IC901 and its peripheral circuits.

Is the audio signal (including sampling

YES YES

output components) output to pins 1 and 7 of IC581 during playback?

Check IC581 and its peripheral circuits.

Check the connections

YES

between pin 26 of IC161 and pin 10 of IC901.

Is the audio signal output at pin 19 and pin 20 of IC161 during playback?

Check IC161 and its peripheral circuits.

YES

Check the power amplifier IC301.

(No.MA232)1-19

5.3 Maintenance of laser pickup

(1) Cleaning the pick up lens

Before you replace the pick up, please try to clean the lens with a alcohol soaked cotton swab.

(2) Life of the laser diode

When the life of the laser diode has expired, the following symptoms will appear.

• The level of RF output (EFM output: amplitude of eye pattern) will be low.

5.4 Replacement of laser pickup

Turn of the power switch and, disconnect the power cord.

Replace the pickup with a normal one. (Refer to "Removing the pickup unit" on the previous page.)

Is RF output

1.3 0.4Vp-p?

Replace it.

YES

(3) Semi-fixed resistor on the APC PC board

The semi-fixed resistor on the APC printed circuit board which is attached to the pickup is used to adjust the laser power.Since this adjustment should be performed to match the characteristics of the whole optical block, do not touch the semi-fixed resistor. If the laser power is lower than the specified value, the laser diode is almost worn out, and the laser pickup should be replaced. If the semi-fixed resistor is adjusted while the pickup is functioning normally, the laser pickup may be damaged due to excessive current.

Plug the power cord in, and turn the power on. At this time, check that the laser emits for about seconds and the objective lens moves up and down. Note: Do not observe the laser beam directly.

Play a disc.

Check the eye-pattern at

RF output or TP RF.

Finish.

1-20 (No.MA232)

5.5 16 PIN CORD DIAGRAM [for KD-AR470]

BL/WH

BK RD

OR/WH

WH/BK

GN/BK

VI/BK

GY/BK

16 YL

8 BK

7 RD

15 OR/WH

13 BR TEL

5 BL/WH

3 GN

MEMORY

GND

ACC

ILL

REMOTE

RL+

CAUTION!

REMOTE

ONLY

OUTPUT

Black

Red

Blue

White

Brown

Green

Violet

Gray

Yellow

Orange

GND

11 GN/BK

10 VI/BK

12 WH/BK

TEL

2 VI

4 WH

1 GY

9 GY/BK

Rear Right

Front Right

Front Left

Rear Left

Telephone muting

RL-

RR+

RR-

FL+

FL-

FR+

FR-

REMOTE

ACC

MEMORY

GND

ILL

Remote out

ACC Line

Memory Backup Battery +

Ground

Illuminations Control

(No.MA232)1-21

5.6 16 PIN CORD DIAGRAM [for KD-G420]

BL/WH

BK RD

OR/WH

WH/BK

GN/BK

VI/BK

GY/BK

16 YL

8 BK

7 RD

15 OR/WH

5 BL/WH

3 GN

MEMORY

GND

ACC

ILL

REMOTE

RL+

REMOTE

CAUTION!

ONLY

OUTPUT

Black

Red

Blue

White

Green

Violet

Gray

Yellow

Orange

GND

11 GN/BK

2 VI

10 VI/BK

4 WH

12 WH/BK

1 GY

9 GY/BK

Rear Right

Front Right

Front Left

Rear Left

RL-

RR+

RR-

FL+

FL-

FR+

FR-

REMOTE

ACC

MEMORY

GND

ILL

Remote out

ACC Line

Memory Backup Battery +

Ground

Illuminations Control

1-22 (No.MA232)

5.7 16 PIN CORD DIAGRAM [for KD-G521 and KD-G527]

OR/WH

BL/WH

VI/BK

GY/BK

WH/BK

GN/BK

VI/BK

GY/BK

WH/BK

GN/BK

RR+

RR-

FR+

FR-

FL+

FL-

RL+

RL-

Black

Red

WH White

Blue

Brown

Green

Violet

Gray

Yellow

Orange

REMOTE

BL/WH

OR/WH ILL

Rear Right

Front Right

Front Left

Rear Left

Remote out

TEL

MEMORY

REMOTE

ACC

GND

ANT

ACC

TEL

GND

MEMORY

MEMORY BACKUP

DIRECT TO BATTERY

+12Volt

ACC + 12Volt

GROUND

Auto Antenna

ACC Line

Telephone Muting

Ground

Memory Backup Battery+

ILL

Illuminations Control

(No.MA232)1-23

5.8 16 PIN CORD DIAGRAM [for KD-G524 and KD-G525]

OR/WH

Black

Green

6 5

4 3

BL/WH

16 YL

8 BK

7 RD

15 OR/WH

3 GN

11 GN/BK

2 VI

WH/BK

GN/BK

VI/BK

GY/BK

MEMORY

GND

ACC

ILL

RL+

RL-

RR+

Red

Blue

WH White

VI Violet

Gray

Yellow

OR Orange

GND

REMOTE

10 VI/BK

4 WH

12 WH/BK

1 GY

9 GY/BK

5 BL/WH

6 BL

Rear Right

Front Right

Front Left

Rear Left

Remote out

RR-

FL+

FL-

FR+

FR-

REMOTE

ANT

ACC

ILL

GND

MEMORY

REMOTE

OUTPUT

ONLY

POWER

ANTENNA

Auto Antenna

ACC Line

Illuminations Control

Ground

Memory Backup Battery+

1-24 (No.MA232)

(No.MA232)1-25

Victor Company of Japan, Limited Mobile Entertainment Business Group Mobile Entertainment Category 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan

(No.MA232)

Printed in Japan

VPT

+ 59 hidden pages