Signal Detection SystemNon-contact optical pickup (semiconductor laser)
Number of Channels2 channels (stereo)
Frequency Response5 Hz to 20 000 Hz
Dynamic Range96 dB
Signal-to-Noise Ratio98 dB
Wow and FlutterLess than measurable limit
MP3 Decoding FormatMPEG1/2 Audio Layer 3
Max. Bit Rate: 320 kbps
WMA (Windows Media Audio) Decoding FormatMax. Bit Rate: 192 kbps
GENERAL
Power RequirementOperating VoltageDC 14.4 V (11 V to 16 V allowance)
Grounding SystemNegative ground
Allowable Operating Temperature0°C to +40°C
Dimensions (W × H × D)Installation Size (approx.)182 mm × 52 mm × 150 mm
Panel Size (approx.)188 mm × 58 mm × 11 mm
Mass (approx.)1.3 kg (excluding accessories)
• Design and specifications are subject to change without notice.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/
or other countries.
1-2 (No.MA136)
Page 3
1.1Safety Precautions
SECTION 1
PRECAUTIONS
!
!
Burrs formed during molding may be left over on some parts of the chassis. Therefore,
pay attention to such burrs in the case of preforming repair of this system.
Please use enough caution not to see the beam directly or touch it in case of an
adjustment or operation check.
(No.MA136)1-3
Page 4
1.2Preventing static electricity
Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser
diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
1.2.1 Grounding to prevent damage by static electricity
Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players.
Be careful to use proper grounding in the area where repairs are being performed.
(1) Ground the workbench
Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the
traverse unit (optical pickup) on it.
(2) Ground yourself
Use an anti-static wrist strap to release any static electricity built up in your body.
(caption)
Anti-static wrist strap
1M
Conductive material
(conductive sheet) or iron plate
(3) Handling the optical pickup
• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical
pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)
• Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily
destroy the laser diode.
1.3Handling the traverse unit (optical pickup)
(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.
(2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the
replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a
time when attaching it to the connector.
(3) Handle the flexible cable carefully as it may break when subjected to strong force.
(4) It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.
1.4Attention when traverse unit is decomposed
*Please refer to "Disassembly method" in the text for the CD pickup unit.
• Apply solder to the short land before the flexible wire is disconnected from the connector on the CD pickup unit.
(If the flexible wire is disconnected without applying solder, the CD pickup may be destroyed by static electricity.)
• In the assembly, be sure to remove solder from the short land after connecting the flexible wire.
Short-circuit point
(Soldering)
Flexible wire
1-4 (No.MA136)
Pickup
Page 5
1.5Important for laser products
!
1.CLASS 1 LASER PRODUCT
2.DANGER : Invisible laser radiation when open and inter
lock failed or defeated. Avoid direct exposure to beam.
3.CAUTION : There are no serviceable parts inside the
Laser Unit. Do not disassemble the Laser Unit. Replace
the complete Laser Unit if it malfunctions.
4.CAUTION : The CD,MD and DVD player uses invisible
laser radiation and is equipped with safety switches which
prevent emission of radiation when the drawer is open and
the safety interlocks have failed or are defeated. It is
dangerous to defeat the safety switches.
5.CAUTION : If safety switches malfunction, the laser is able
to function.
6.CAUTION : Use of controls, adjustments or performance of
procedures other than those specified here in may result in
hazardous radiation exposure.
Please use enough caution not to
see the beam directly or touch it
in case of an adjustment or operation
check.
REPRODUCTION AND POSITION OF LABELS
WARNING LABEL
CAUTION : Visible and Invisible
CLASS 1
LASER PRODUCT
laser radiation when open and
interlock failed or defeated.
AVOID DIRECT EXPOSURE TO
BEAM. (e)
ADVARSEL : Synlig og usynlig
laserstråling når maskinen er
åben eller interlocken fejeler.
Undgå direkte eksponering til
stråling. (d)
VARNING : Synlig och
osynling laserstrålning när
den öppnas och spärren är
urkopplad. Betrakta ej
strålen. (s)
VARO : Avattaessa ja suojalukitus
ohitettuna tai viallisena olet alttiina
näkyvälle ja näkymättömälle
lasersäteilylle. Vältä säteen
kohdistumista suoraan itseesi. (f)
(No.MA136)1-5
Page 6
SPECIFIC SERVICE INSTRUCTIONS
2.1HOW TO IDENTIFY MODELS
2.1.1 NAME PLATE (as same as KD-G416)
SECTION 2
Discernment sign
1-6 (No.MA136)
Discernment sign
Page 7
SECTION 3
DISASSEMBLY
3.1Main body section
3.1.1 Removing the front panel assembly
(See Fig.1)
(1) Push the detach button in the lower right part of the front
panel assembly and remove the front panel assembly.
3.1.2 Removing the bottom cover
(See Fig.2)
(1) Turn the main body up side down.
(2) Insert a screwdriver under the joints to release the two
joints a on the left side, two joints b on the right side and
joint c on the back side of the main body, then remove the
bottom cover from the main body.
Note:
When releasing the joints using a screwdriver, do not damage
the main board.
Front panel assembly
Joint a
Detach button
Fig.1
Bottom cover
Joint b
3.1.3 Removing the front chassis assembly
(See Fig.3)
• Remove the front panel assembly and bottom cover.
(1) Remove the two screws A on the both sides of the main
body.
(2) Release the two joints d and two joints e on the both sides
of the main body, then remove the front chassis assembly
toward the front.
Joint a
Joint c
Fig.2
Joint dJoint e
A
Joint d
Front chassis assembly
Fig.3
Joint e
Joint b
(No.MA136)1-7
Page 8
3.1.4 Removing the side panel
(See Fig.4)
Reference:
Remove the front panel assembly as required.
(1) Remove the screw B and two screws C attaching the side
panel on the left side of the main body.
(2) Remove the side panel from the main body.
3.1.5 Removing the rear bracket
(See Fig.5)
• Remove the bottom cover.
(1) Remove the three screws D, three screws E and two
screws F attaching the rear bracket on the back side of the
main body.
(2) Remove the rear bracket.
3.1.6 Removing the main board
(See Figs.5 and 6)
• Remove the front panel assembly, bottom cover and side pan-
el.
Reference:
Remove the front chassis assembly as required.
(1) Remove the three screws D attaching the rear bracket on
the back side of the main body. (See Fig.5.)
(2) Remove the two screws G attaching the main board. (See
Fig.6.)
(3) Disconnect the connector CN501
the main body and take out the main board with the rear
bracket. (See Fig.6.)
Reference:
Remove the rear bracket from the main body as required. (See
"3.1.5 Removing the rear bracket".)
on the main board from
C
B
Side panel
Fig.4
Rear bracket
EF
F
C
E
DD
Fig.5
CN501
G
Main board
G
1-8 (No.MA136)
Rear bracket
Fig.6
Page 9
3.1.7 Removing the CD mechanism assembly
(See Fig. 7)
• Remove the front panel assembly, bottom cover, side panel,
rear bracket and main board.
Reference:
Remove the front chassis assembly as required.
(1) Remove the three screws H attaching the CD mechanism
assembly on the top chassis.
(2) Take out the CD mechanism assembly.
H
3.1.8 Removing the switch board
(See Figs.8 to 10)
• Remove the front panel assembly.
(1) Remove the five screws J on the back side of the front pan-
el assembly. (See Fig.8.)
(2) Release the twelve joints f and remove the rear cover. (See
Fig.9.)
(3) Release the joint g and take out the switch board from the
front panel assembly. (See Fig.10.)
Note:
When removing the rear cover assembly and switch board, be
careful not to lose the spring.
CD mechanism assembly
J
Rear cover
Top chassis
H
Fig.7
J
J
Fig.8
Joints f
Joints fJoints f
Switch board
Joints f
Fig.9
Front panel assembly
Joint g
Fig.10
(No.MA136)1-9
Page 10
3.2CD Mechanism Assembly
A
3.2.1 Removing the top cover
(See Figs.1 and 2)
(1) Remove the two screws A on the both side of the body.
(2) Lift the front side of the top cover and move the top cover
backward to release the two joints a.
Top cover
Joints a
A
Joints a
A
Fig.1
Fig.2
Top cover
1-10 (No.MA136)
Page 11
3.2.2 Removing the connector board
(See Figs.3 to 5)
CAUTION:
Before disconnecting the flexible wire from the pickup, solder
the short-circuit point on the pickup. No observance of this in-
struction may cause damage of the pickup.
(1) Remove the screw B fixing the connector board.
(2) Solder the short-circuit point on the connector board.
(3) Disconnect the flexible wire from the pickup.
(4) Move the connector board in the direction of the arrow to
release the two joints b.
(5) Unsolder the wire on the connector board if necessary.
CAUTION:
Unsolder the short-circuit point after reassembling.
B
Connector board
Flexible wire
Wires
Joints b
Short-circuit point
Fig.3
Short-circuit point
(Soldering)
Pickup
Flexible wire
Frame
Pickup
Fig.4
B
Connector board
Fig.5
(No.MA136)1-11
Page 12
3.2.3 Removing the DET switch
(See Figs.6 and 7)
(1) Extend the two tabs c of the feed sw. holder and pull out
the switch.
(2) Unsolder the DET switch wire if necessary.
Connector
board
DET switch
DET switch
Pickup
Fig.6
Tab c
DET switch wire
Tab c
Feed sw. holder
Fig.7
1-12 (No.MA136)
Page 13
3.2.4 Removing the chassis unit
r
(See Figs.8 and 9)
• Prior to performing the following procedure, remove the top
cover and connector board.
(1) Remove the two suspension springs (L) and (R) attaching
the chassis unit to the frame.
CAUTION:
• The shape of the suspension spring (L) and (R) are different. Handle them with care.
• When reassembling, make sure that the three shafts
on the underside of the chassis unit are inserted to the
dampers certainly.
Suspension spring (R)
Chassis unit
Suspension spring (L)
Frame
Suspension spring (R)
Chassis unit
Shafts
Damper
Damper
Suspension spring (L)
Fig.8
Shaft
Dampe
Frame
Fig.9
(No.MA136)1-13
Page 14
3.2.5 Removing the clamper assembly
(See Figs.10 and 11)
• Prior to performing the following procedure, remove the top
cover.
(1) Remove the clamper arm spring.
(2) Move the clamper assembly in the direction of the arrow to
release the two joints d.
Clamper arm
spring
Joint d
Joint d
Clamper assembly
Fig.10
Clamper arm spring
Chassis rivet
assembly
Joint d
Clamper
assembly
Chassis rivet assembly
Fig.11
Joint d
1-14 (No.MA136)
Page 15
3.2.6 Removing the loading / feed motor assembly
(See Figs.12 and 13)
• Prior to performing the following procedure, remove the top
cover, connector board and chassis unit.
(1) Remove the screw C and move the loading / feed motor
assembly in the direction of the arrow to remove it from the
chassis rivet assembly.
(2) Disconnect the wire from the loading / feed motor assembly
if necessary.
CAUTION:
When reassembling, connect the wire from the loading /
feed motor assembly to the flame as shown in Fig.12.
Loading / feed motor assembly
Fig.12
Loading / feed motor assembly
C
Fig.13
(No.MA136)1-15
Page 16
3.2.7 Removing the pickup unit
(See Figs.14 to 18)
• Prior to performing the following procedure, remove the top
cover, connector board and chassis unit.
(1) Remove the screw D and pull out the pu. shaft holder from
the pu. shaft.
(2) Remove the screw E attaching the feed sw. holder.
(3) Move the part e of the pickup unit upward with the pu. shaft
and the feed sw. holder, then release the joint f of the feed
sw. holder in the direction of the arrow. The joint g of the
pickup unit and the feed rack is released, and the feed sw.
holder comes off.
(4) Remove the pu. shaft from the pickup unit.
(5) Remove the screw F attaching the feed rack to the pickup
unit.
3.2.8 Reattaching the pickup unit
(See Figs.14 to 17)
(1) Reattach the feed rack to the pickup unit using the screw F.
(2) Reattach the feed sw. holder to the feed rack while setting
the joint g to the slot of the feed rack and setting the part f
of the feed rack to the switch of the feed sw. holder correctly.
(3) As the feed sw. holder is temporarily attached to the pickup
unit, set to the gear of the joint g and to the bending part of
the chassis (joint h) at a time.
CAUTION:
Make sure that the part i on the underside of the feed
rack is certainly inserted to the slot j of the change lock
lever.
(4) Reattach the feed sw. holder using the screw E.
(5) Reattach the pu. shaft to the pickup unit. Reattach the pu.
shaft holder to the pu. shaft using the screw D.
Feed sw. holder
Joint f
Joint g
Feed sw.
holder
Part e
Feed rack
Part i
E
Pickup unit
Slot j
F
Fig.15
Pu. shaft
Pickup unit
Joint f
Joint h
Fig.16
Feed rack
Pickup unit
Feed sw. holder
D
Pu. shaft
holder
Pu. shaft
D
Pu. shaft holder
1-16 (No.MA136)
Pickup unit
Fig.14
Part e
E
Joint g
Feed rack
Fig.17
Pickup unit
Joint g
Joint f
Feed sw. holder
Fig.18
Page 17
3.2.9 Removing the trigger arm
r
(See Figs.19 and 20)
• Prior to performing the following procedure, remove the top
cover, connector board and clamper unit.
(1) Turn the trigger arm in the direction of the arrow to release
the joint k and pull out upward.
CAUTION:
When reassembling, insert the part m and n of the trigger
arm into the part p and q at the slot of the chassis rivet
assembly respectively and join the joint k at a time.
Chassis rivet assembly
Trigger arm
Chassis rivet
assembly
Joint k
Trigger arm
Fig.19
Part p
Part q
Part m
Part n
3.2.10 Removing the top plate assembly
(See Fig.21)
• Prior to performing the following procedure, remove the top
cover, connector board, chassis unit, and clamper assembly.
(1) Remove the screw H.
(2) Move the top plate assembly in the direction of the arrow to
release the two joints r.
(3) Unsolder the wire marked s if necessary.
H
Fig.20
Top plate assembly
Joints
s
Fig.21
(No.MA136)1-17
Page 18
3.2.11 Removing the mode sw. / select lock arm
(See Figs.22 and 23)
• Prior to performing the following procedure, remove the top
plate assembly.
(1) Bring up the mode sw. to release from the link plate (joint t)
and turn in the direction of the arrow to release the joint u.
(2) Unsolder the wire of the mode sw. marked s if necessary.
(3) Turn the select lock arm in the direction of the arrow to re-
lease the two joints v.
(4) The select lock arm spring comes off the select lock arm at
the same time.
Top plate
Link plate
Joint u
Joint t
s
Fig.22
Select lock arm
Select lock arm
Mode sw.
Select lock arm
Top plate
Hook w
Select lock
arm spring
Link plate
Joints v
Fig.23
1-18 (No.MA136)
Page 19
3.2.12 Reassembling the mode sw. / select lock arm
(See Figs.24 to 26)
REFERENCE:
Reverse the above removing procedure.
(1) Reattach the select lock arm spring to the top plate and set
the shorter end of the select lock arm spring to the hook w
on the top plate.
(2) Set the other longer end of the select lock arm spring to the
boss x on the underside of the select lock arm, and join the
select lock arm to the slots (joint v). Turn the select lock
arm as shown in the figure.
(3) Reattach the mode sw. while setting the part t to the first
peak of the link plate gear, and join the joint u.
CAUTION:
When reattaching the mode sw., check if the points y and
z are correctly fitted and if each part operates properly.
Select lock arm spring
Hook w
Joint v
Joint v
Select lock arm
Boss x
Fig.24
Joint t
Point y
Link plate
Point z
Link plate
Fig.25
Mode sw.
Select
lock arm
Joint t
Joint u
Fig.26
(No.MA136)1-19
Page 20
3.2.13 Removing the select arm R / link plate
(See Figs.27 and 28)
• Prior to performing the following procedure, remove the top
plate assembly.
(1) Bring up the select arm R to release from the link plate
(joint a') and turn as shown in the figure to release the two
joints b' and joint c'.
(2) Move the link plate in the direction of the arrow to release
the joint d'. Remove the link plate spring at the same time.
REFERENCE:
Before removing the link plate, remove the mode sw..
Select arm R
Joint b'
Link plate spring
Joint c'
Joint a'
Link plate
Joint b'
Fig.27
Joint r
3.2.14 Reattaching the Select arm R / link plate
(See Figs.29 and 30)
REFERENCE:
Reverse the above removing procedure.
(1) Reattach the link plate spring.
(2) Reattach the link plate to the link plate spring while joining
them at joint d'.
(3) Reattach the joint a' of the select arm R to the first peak of
the link plate while joining the two joints b' with the slots.
Then turn the select arm R as shown in the figure. The top
plate is joined to the joint c'.
CAUTION:
When reattaching the select arm R, check if the points e'
and f' are correctly fitted and if each part operates properly.
Top plate
Select arm R
Joint b'
Joint d'
Link plate
Fig.28
Link plate spring
Joint c'
Joint d'
Joint b'
Joint a'
Fig.29
1-20 (No.MA136)
Joint a'
Point e'
Link plate
Point f'
Fig.30
Page 21
3.2.15 Removing the loading roller assembly
(See Figs.31 to 33)
• Prior to performing the following procedure, remove the
clamper assembly and top plate assembly.
(1) Push inward the loading roller assembly on the gear side
and detach it upward from the slot of the joint g' of the lock
arm rivet assembly.
(2) Detach the loading roller assembly from the slot of the joint
h' of the lock arm rivet assembly.
Roller guide
spring
Part k'
Loading roller assembly
Loading roller assembly
The roller guide comes off the gear section of the loading
roller assembly.
Remove the roller guide and the HL washer from the shaft
of the loading roller assembly.
(3) Remove the screw J attaching the lock arm rivet assembly.
(4) Push the shaft at the joint i' of the lock arm rivet assembly
inward to release the lock arm rivet assembly from the slot
of the L side plate.
(5) Extend the lock arm rivet assembly outward and release
the joint j' from the boss of the chassis rivet assembly. The
roller guide springs on both sides come off at the same
time.
CAUTION:
When reassembling, reattach the left and right roller
guide springs to the lock arm rivet assembly before reattaching the lock arm rivet assembly to the chassis rivet
assembly. Make sure to fit the part k' of the roller guide
spring inside of the roller guide. (Refer to Fig.34.)
Roller guide
HL washer
Loading roller assembly
Roller guide
Chassis rivet assembly
J
Roller guide
spring
Fig.32
Boss
L side plate
Roller guide spring
Joint h'
Roller guide spring
Loading roller assembly
Joint g'
Lock arm rivet assembly
Fig.31
Roller guide spring
Roller guide spring
Lock arm rivet assembly
Lock arm rivet assembly
Joint i'
Part j'
Fig.33
Roller guide
HL washer
Roller shaft assembly
Loading roller
Roller guide spring
Fig.34
(No.MA136)1-21
Page 22
3.2.16 Removing the loading gear 5, 6 and 7
(See Figs.35 and 36)
• Prior to performing the following procedure, remove the top
cover, chassis unit, pickup unit and top plate assembly.
(1) Remove the screw K attaching the loading gear bracket.
The loading gear 6 and 7 come off the loading gear bracket.
(2) Pull out the loading gear 5.
K
Loading gear bracket
K
Loading gear 6
Loading gear 5
Loading gear 3
Fig.35
Loading gear bracket
Loading gear 5
Loading gear 6
Loading gear 7
Fig.36
1-22 (No.MA136)
Page 23
3.2.17 Removing the gears
(See Figs.37 to 40)
• Prior to performing the following procedure, remove the top
cover, chassis unit, top plate assembly and pickup unit.
• Pull out the loading gear 3. (See Fig.35.)
(1) Pull out the feed gear.
(2) Move the loading plate assembly in the direction of the ar-
row to release the L side plate from the two slots m' of the
chassis rivet assembly. (See Fig.37.)
(3) Detach the loading plate assembly upward from the chas-
sis rivet assembly while releasing the joint n'. Remove the
slide hook and loading plate spring from the loading plate
assembly.
(4) Pull out the loading gear 2 and remove the change lock le-
ver.
(5) Remove the E ring and washer attaching the changer gear
2.
(6) The changer gear 2, change gear spring and adjusting
washer come off.
(7) Remove the loading gear 1.
(8) Move the change plate rivet assembly in the direction of the
arrow to release from the three shafts of the chassis rivet
assembly upward. (See Fig.38.)
(9) Detach the loading gear plate rivet assembly from the shaft
of the chassis rivet assembly upward while releasing the
joint p'. (See Figs.38 and 40.)
(10) Pull out the loading gear 4.
Change plate
rivet assembly
Shafts
E ring
Loading plate assembly
Loading plate spring
Joint p'
Loading gear 4
Loading gear plate
rivet assembly
Shaft
Loading gear 2
Loading gear 1
Chassis rivet assembly
Change gear 2
Fig.38
Joint n'
Slide hook
Feed gear
Fig.37
Slot m'
L side plate
Loading plate assembly
Joint n'
Slot m'
Chassis rivet assembly
Chassis rivet assembly
E ring
Washer
Change gear 2
Change gear spring
Adjusting washer
Change plate
rivet assembly
Chassis rivet assembly
L side plate
Slot m'
Slot m'
Fig.39
Loading gear 1
Loading gear 2
Change lock lever
Loading gear 4
Loading gear plate rivet assembly
Fig.40
(No.MA136)1-23
Page 24
3.2.18 Removing the turn table / spindle motor
(See Figs.41 and 42)
• Prior to performing the following procedure, remove the top
cover, connector board, chassis unit and clamper assembly.
(1) Remove the two screws L attaching the spindle motor as-
sembly through the slot of the turn table on top of the body.
(2) Unsolder the wire on the connector board if necessary.
Turn table
L
Fig.41
L
Turn table
1-24 (No.MA136)
Spindle motor
Fig.42
Page 25
SECTION 4
ADJUSTMENT
4.1Adjustment method
Test instruments required for adjustment
(1) Digital oscilloscope (100MHz)
(2) Electric voltmeter
(3) Digital tester
(4) Tracking offset meter
(5) Test Disc JVC :CTS-1000
(6) Extension cable for check
EXTSH002-22P × 1
Standard volume position
Balance and Bass &Treble volume : lndication"0"
Loudness : OFF
How to connect the extension cable for adjusting
Caution:
Be sure to attach the heat sink and rear bracket onto the power amplifier IC and regulator IC respectively, before supply the power.
If voltage is applied without attaching these parts, the power amplifier IC and regulator IC will be destroyed by heat.
Standard measuring conditions
Power supply voltageDC14.4V(11 to 16V)
Load impedance20KΩ(2 Speakers connection)
Output LevelLine out 2.0V (Vol. MAX)
Dummy load
Exclusive dummy load should be used for AM,and FM. For FM
dummy load,there is a loss of 6dB between SSG output and
antenna input.The loss of 6dB need not be considered since
direct reading of figures are applied in this working standard.
Heat sink
Extension cable
EXTSH002-22P
Rear bracket
(No.MA136)1-25
Page 26
5.1KD-G416,KD-G415 J model
5.1.1 Feed section
SECTION 5
TROUBLESHOOTING
Is 5v or 0V at IC541
pin 40?
YES
Is 4V present at both
sides of the feed motor?
YES
Check the feed motor.
5.1.2 Focus section
5.1.3 Spindle section
Is the disk rotated?
NO
Is the wiring for IC541
pin 40 correct?
NO
Is 6V or 2V present at
IC501 pins 4 and 5?
Check IC501.
When the lens is
moving:
Does the S-search
waveform appear at
IC501 pins 8 and 9?
NO
Is 4V present between
IC501 pins 6 and 7?
NO
NO
YES
4V
YES
Is 5V present at IC501
pin 20?
Check the vicinity of
IC541.
YES
Check the feed motor
connection wiring.
NO
NO
Check the circuits in
the vicinity of IC501
pins 15 and 16.
Check the pickup and
its connections.
Is 4V present at IC541
pin 41?
YES
YES
NO
NO
Check CD8V.
Check IC541.
YES
Does the RF signal
appear at RF test point?
YES
Is the RF waveform at
RF test point distorted?
YES
Proceed to the Tracking
section
5.1.4 Tracking section
When the disc is rotated
at first:
Is the tracking error
signal output at IC521
pin 11?
Check the spindle motor
and its wiring.
NO
Check the circuits in
the vicinity of IC521 pins
2 to 12 or the pickup.
NO
Approx. 1.2V
YES
Check IC541.
NO
YES
Check the circuits in
the vicinity of IC521
pins 2 to 12.
YES
Check the vicinity of
IC501.
NO
Check the pickup and
its connections.
1-26 (No.MA136)
Page 27
5.1.5 Signal processing section
Is the sound output from
both channels (L, R)?
YES
Normal
NO
No sound from either
channel.
Is 9V present at IC161
pin 31?
Is the audio signal
(including sampling
output components)
output to IC581 pins 1
and 7 during playback?
Is the audio signal
output at IC161 pins 3
and 30 during playback?
YES
YES
YES
Compare the L-ch and
NO
R-ch to locate the
defective point.
NO
Is 9V present at IC901
pin 13?
Check the connection
between IC901 pin13
and IC161 pin31.
NO
Check IC581 and its
peripheral circuits.
NO
Check IC161 and its
peripheral circuits.
YES
NO
Check IC901 and its
peripheral circuits.
YES
Check the power amp.
IC301.
(No.MA136)1-27
Page 28
5.2KD-G416,KD-G415 J2 version model
5.2.1 Feed section
Is 5v or 0V at IC521
pin 7?
YES
Is 4V present at both
sides of the feed motor?
YES
Check the feed motor.
5.2.2 Focus section
5.2.3 Spindle section
Is the disk rotated?
NO
Is the wiring for IC521
pin 7 correct?
NO
Is 6V or 2V present at
IC501 pins 17 and 18?
Check IC501.
When the lens is
moving:
Does the S-search
waveform appear at
IC501 pins 9 and 10?
NO
Is 4V present between
IC501 pins 15 and 16?
NO
NO
YES
4V
YES
Is 5V present at IC501
pin 7?
Check the vicinity of
IC521.
YES
Check the feed motor
connection wiring.
NO
Check the circuits in
the vicinity of IC501
pin 26.
Check the pickup and
its connections.
NO
Is 4V present at IC521
pin 5?
YES
YES
NO
NO
Check CD8V.
Check IC521.
YES
Does the RF signal
appear at ARF test point?
YES
Is the RF waveform at
ARF test point distorted?
YES
Proceed to the Tracking
section
5.2.4 Tracking section
When the disc is rotated
at first:
Is the tracking error
signal output at IC521
pin 25?
Check the spindle motor
and its wiring.
NO
Check the circuits in
the vicinity of IC521 pins
28 to 35 or the pickup.
NO
Approx. 1.2V
YES
Check IC521.
NO
YES
Check the circuits in
the vicinity of IC521
pins 28 to 35.
YES
Check the vicinity of
IC501.
NO
Check the pickup and
its connections.
1-28 (No.MA136)
Page 29
5.2.5 Signal processing section
Is the sound output from
both channels (L, R)?
YES
Normal
NO
No sound from either
channel.
Is 9V present at IC161
pin 31?
Is the audio signal
(including sampling
output components)
output to IC581 pins 1
and 7 during playback?
Is the audio signal
output at IC161 pins 3
and 30 during playback?
YES
YES
YES
Compare the L-ch and
NO
R-ch to locate the
defective point.
NO
Is 9V present at IC901
pin 13?
Check the connection
between IC901 pin13
and IC161 pin31.
NO
Check IC581 and its
peripheral circuits.
NO
Check IC161 and its
peripheral circuits.
YES
NO
Check IC901 and its
peripheral circuits.
YES
Check the power amp.
IC301.
(No.MA136)1-29
Page 30
5.3Maintenance of laser pickup
(1) Cleaning the pick up lens
Before you replace the pick up, please try to clean the lens
with a alcohol soaked cotton swab.
(2) Life of the laser diode
When the life of the laser diode has expired, the following
symptoms will appear.
• The level of RF output (EFM output: amplitude of eye
pattern) will be low.
5.4Replacement of laser pickup
Turn of the power switch and, disconnect the
power cord.
Replace the pickup with a normal one. (Refer
to "Removing the pickup unit" on the previous page.)
Is RF output
1.3 0.4Vp-p?
NO
Replace it.
YES
OK
(3) Semi-fixed resistor on the APC PC board
The semi-fixed resistor on the APC printed circuit board
which is attached to the pickup is used to adjust the laser
power.Since this adjustment should be performed to match
the characteristics of the whole optical block, do not touch
the semi-fixed resistor.
If the laser power is lower than the specified value, the laser diode is almost worn out, and the laser pickup should
be replaced. If the semi-fixed resistor is adjusted while the
pickup is functioning normally, the laser pickup may be
damaged due to excessive current.
Plug the power cord in, and turn the power on.
At this time, check that the laser emits for about
seconds and the objective lens moves up and down.
Note: Do not observe the laser beam directly.
Play a disc.
Check the eye-pattern at
RF test point or
ARF test point.
Finish.
1-30 (No.MA136)
Page 31
5.516 PIN CORD DIAGRAM
BK
8
YL
16
7
6
5
4
3
2
1
RD
BL
BL/WH
WH
GN
VI
GY
16 YL
8 BK
7 RD
3 GN
11 GN/BK
2 VI
NC
15
14
NC
NC
13
WH/BK
12
GN/BK
11
10
VI/BK
GY/BK
9
MEMORY
GND
ACC
RL+
RL-
RR+
BK
RD
BL
Black
Red
Blue
WH White
GN
Green
VIViolet
GY
YL
Gray
Yellow
GND
RR
FR
FL
RL
REMOTE
10 VI/BK
4 WH
12 WH/BK
1 GY
9 GY/BK
5 BL/WH
6 BL
Rear Right
Front Right
Front Left
Rear Left
Remote
RR-
FL+
FL-
FR+
FR-
REMOTE
ANT
ANT
ACC
GND
MEMORY
REMOTE
OUTPUT
ONLY
POWER
ANTENNA
Auto Antenna
ACC Line
Ground
Memory Backup Battery+
(No.MA136)1-31
Page 32
Victor Company of Japan, Limited
AV & MULTIMEDIA COMPANY AUDIO/VIDEO SYSTEMS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan
(No.MA136)
Printed in Japan
VPT
Page 33
PARTS LIST
[ KD-G415 ] [ KD-G416 ]
* All printed circuit boards and its assemblies are not available as service parts.
Area suffix
UT ---------------------------Taiwan
UH -------------------------Thailand
UN ----------------------------Asean
U --------------------OtherAreas
MA136
- Contents -
Exploded view of general assembly and parts list (Block No.M1)
CD mechanism assembly and parts list (Block No.MB)
Electrical parts list (Block No.01~02) (UT.UH.UN.U)
Electrical parts list (Block No.03~04) (UT2.UH2.UN2.U2)
Electrical parts list (Block No.05~06) (UH3.UN3.U3)
Packing materials and accessories parts list (Block No.M3)
3- 2
3- 6
3- 8
3-12
3-16
3-22
3-1
Page 34
Exploded view of general assembly and parts list
4
1
Block No.
54
5
8
5
3
C
B
2
4
M
1
M
1
M
A
9
18
4
16
15
14
13
34
25
20
23
30
4
Switch
27
29
19
31
board
28
24
22
21
33
33
33
53
32
26
3-2
Page 35
6
45
49
6
46
48
50
C
44
6
13
14
17
10
51
52
B
Main board
A
47
7
12
9
11
7
39
34
42
37
36
43
35
38
40
41
3-3
Page 36
General Assembly
Symbol No.Part No.Part NameDescriptionLocal
1GE10104-001ATOP CHASSIS
2GE40135-001AEARTH PLATE
3GE30938-003ASIDE PANEL
4QYSDST2604ZATAP SCREWM2.6 x 4mm(x3)
5GE40235-001ASCREW(x2)
6QYSDST2604ZATAP SCREWM2.6 x 4mm(x3)
7GE40235-004ASCREW(x2)
8QYSDST2610ZATAP SCREWM2.6 x 10mm
9QYSDST2004ZATAP SCREWM2 x 4mm(x2)
10GE10103-001AFRONT CHASSIS
11GE31569-002ALOCK LEVER
12GE40269-001ATORSION SPRING
13GE31568-001ARLS KNOB
14GE40202-011ACOMP.SPRING
15GE40250-001APANEL STOPPER
16GE40202-009ACOMP.SPRING
17GE40257-001ABLIND
18FSYH4036-098SHEET
44QMFZ047-150-TFUSE15A
45GE31571-005AREAR BRACKET
46QYSDST2606ZATAP SCREWM2.6 x 6mm
47QYSDST2606ZATAP SCREWM2.6 x 6mm
48QYSDSF2606ZATAP SCREWM2.6 x 6mm
49QYSDSF2606ZATAP SCREWM2.6 x 6mm(x2)
50GE40172-004AIC BRACKET
51GE40103-003AREG BRACKET
52GE40107-002AHEAT SINK
53GE30854-001ALED HOLDER
54GE31574-008AUT LABEL
54GE31574-009AUT LABEL
G416U2,G416UH2,G416UN2,G41 6UT2
G415UT,G415UT2
G416UT,G416UT2
3-5
Page 38
CD mechanism assembly and parts list
Grease
TNG-87
GP-501MK
CFD-005Z
GP-305T
31
C
22
112
24
61
26
36
29
M
M
B
M
111
72
116
74
35
TN-2001-1011
34
33
111
73
25
111
85
15
Block No.
2
37
A
19
B
21
62
D
75
112
114
11
38
30
A
23
13
27
32
101
93
76
94
122
100
84
73
95
38
74
100
99
28
115
D
96
14
123
94
75
77
a
32
97
a
113
81
111
C
B
90
89
92
91
111
93
71
82
18
20
87
125
88
3
The parts without symbol number are not service.
12
121
16
17
124
83
86
3
98
83
4
1
111
3-6
Page 39
CD mechanism
Symbol No.Part No.Part NameDescriptionLocal
130320101TFRAME
230320102TTOP COVER
330320115TDANPER F
430320116TDANPER R
11303205505TCHASSIS RIVET
12303205503TCHANGE P. RVT A
13303205301TCLAMPER ASS'Y
14303205302TSPINDLE MOTOR A
1530320502TCLAMPER ARM
1630320503TCHANGE GEAR SPG
1730320505TCHANGE GEAR 2
1830320506TFEED GEAR
1930320507TFEED RACK
2030320509TCHANGE LOCK RAR
2130320510TFEED SW HOLDER
2230320511TPU SHAFT HOLDER
2330320513TCLAMPER SUB SPG
2430320514TFD SUB HOLDER
2530320518TTOP PLATE
2630320519TSELECT LOCK ARM
2730320520TTRIGGER ARM
2830320521TSLIDE HOOK
2930320522TPU SHAFT
3030320525TCLAMPER ARM SPG
3130320526TSELECT L ARM SP
3230320538TSUSPENSION SP R
3330320529TSELECT ARM R
3430320530TLINK PLATE
3530320531TLINK PLATE SPG
3630320523TCUSHION F
3730320524TCUSHION R
3830320539TSUSPENSION SP L
6169011614TPICKUP OPT-725
6264180406TDET SW ESE22
71303210301TCONN PWB ASS'Y
7230321002TMODE SW
7330321003TLOAD MOTOR WIRE
7430321005TMODE SW WIRE
7530321009TSL WIRE
7630321011TWIRE HOLDER
7719501403TWIRE CLUMPER
81303211301TROLLER SHAFT AS
82303211501TL GEAR PLATE RV
83303211302TLOADING PLATE A
84303211502TLOCK ARM RV ASS
85303211303TL/F MOTOR ASS'Y
8630321101TLOADING GEAR 1
8730321102TLOADING GEAR 2
8830321103TLOADING GEAR 3
8930321104TLOADING GEAR 4
9030321105TLOADING GEAR 5
9130321106TLOADING GEAR 6
9230321107TLOADING GEAR 7
9330321149TROLLER GUIDE
9430321114TROLLER GUIDE SP
9530321116TDISC STOPPER AR
9630321117TDISC ST ARM SPG
9730321118TLD GEAR BRACKET
9830321125TL SIDE PLATE
9930321131TLOAD PLATE SPG
10030321133TLDG ROLLER
10118211223TCOLLAR SCREW
1119P0420031TSCREW
1129P0420041TTAP.SCREW
1139B0320041TSCREW
1149C0117183TSCREW
1159C0120203TSCREW
1169C0317503TSCREW
1219W0130170TPW 3.5X8X0.3
1229W0513060THL WASHER
1239W0710070TL WASHER
1249E0100152TE RING
1259W0113020TPW 2.1X4X0.13
Block No. [M][B][M][M]
3-7
Page 40
Electrical parts list
Main board (UT.UH.UN.U)
Block No. [0][1]
Symbol No.
IC31TB2118F-XPLL IC
IC161TEA6320T-XIC
IC301LA47516POWER IC
IC401TC94A34FG-002IC
IC461NJU7772F15-XIC
IC481AK4385ET-XIC
IC501LA6242H-XIC
IC521TA2157FN-XRF AMP IC
IC541TC94A14FACD LSI IC
IC581NJM4565M-WEIC
IC701UPD784217AGC302IC
IC702IC-PST3433U-XIC
IC901AN80T07AREGULATOR IC
C1QEKJ1CM-226ZE CAPACITOR22uF 16V M
C2NCB31EK-473XC CAPACITOR0.047uF 25V K
C3NCB31EK-103XC CAPACITOR0.01uF 25V K
C4QEKJ1AM-227ZE CAPACITOR220uF 10V M
Part No.Part NameDescriptionLocal
Symbol No.
C5QERF1HM-104ZE CAPACITOR0.1uF 50V M
C6NCB31HK-103XC CAPACITOR0.01uF 50V K
C7QEKJ1CM-226ZE CAPACITOR22uF 16V M
C31QEKJ1AM-107ZE CAPACITOR100uF 10V M
C32NDC31HJ-470XC CAPACITOR47pF 50V J
C33QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C34NCB31EK-473XC CAPACITOR0.047uF 25V K
C35NDC31HJ-100XC CAPACITOR10pF 50V J
C36NDC31HJ-7R0XC CAPACITOR7pF 50V J
C37NDC31HJ-100XC CAPACITOR10pF 50V J
C38NCB31HK-102XC CAPACITOR1000pF 50V K
C39NCB31HK-102XC CAPACITOR1000pF 50V K
C40QEKJ1CM-106ZE CAPACITOR10uF 16V M
C41NCB31EK-473XC CAPACITOR0.047uF 25V K
C42NCB31HK-103XC CAPACITOR0.01uF 50V K
C43QFV61HJ-473ZMF CAPACITOR0.047uF 50V J
C44NCB31HK-103XC CAPACITOR0.01uF 50V K
C45NCB31HK-272XC CAPACITOR2700pF 50V K
C46NCB31HK-103XC CAPACITOR0.01uF 50V K
C47NCB31HK-103XC CAPACITOR0.01uF 50V K
C48NCB31EK-473XC CAPACITOR0.047uF 25V K
C49NCB31HK-102XC CAPACITOR1000pF 50V K
C50NDC31HJ-101XC CAPACITOR100pF 50V J
C51NDC31HJ-331XC CAPACITOR330pF 50V J
C81QEKJ1HM-105ZE CAPACITOR1uF 50V M
C82NCB31HK-332XC CAPACITOR3300pF 50V K
C84NCB31HK-153XC CAPACITOR0.015uF 50V K
C91QEKJ1HM-105ZE CAPACITOR1uF 50V M
C92NCB31HK-332XC CAPACITOR3300pF 50V K
C94NCB31HK-153XC CAPACITOR0.015uF 50V K
C95NCB31HK-103XC CAPACITOR0.01uF 50V K
C161QTE1H54-225ZE CAPACITOR2.2uF 50V
C162QEKJ1HM-105ZE CAPACITOR1uF 50V M
C164NCB31HK-822XC CAPACITOR8200pF 50V K
C165NCB31AK-224XC CAPACITOR0.22uF 10V K
C166NCB21CK-224XC CAPACITOR0.22uF 16V K
C167NCB31EK-333XC CAPACITOR0.033uF 25V K
C168NCB31HK-562XC CAPACITOR5600pF 50V K
C169QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C170QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C171QTE1H54-225ZE CAPACITOR2.2uF 50V
C172QEKJ1HM-105ZE CAPACITOR1uF 50V M
C174NCB31HK-822XC CAPACITOR8200pF 50V K
C175NCB31AK-224XC CAPACITOR0.22uF 10V K
C176NCB21CK-224XC CAPACITOR0.22uF 16V K
C177NCB31EK-333XC CAPACITOR0.033uF 25V K
C178NCB31HK-562XC CAPACITOR5600pF 50V K
C179QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C180QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C191QEKJ1CM-476ZE CAPACITOR47uF 16V M
C192QEKJ1AM-107ZE CAPACITOR100uF 10V M
C193QEKJ1AM-107ZE CAPACITOR100uF 10V M
C194NCB31EK-823XC CAPACITOR0.082uF 25V K
C301QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C302QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C303NDC31HJ-101XC CAPACITOR100pF 50V J
C304NDC31HJ-101XC CAPACITOR100pF 50V J
C307QEKJ1HM-105ZE CAPACITOR1uF 50V M
C308QEKJ1HM-105ZE CAPACITOR1uF 50V M
C311QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C312QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C313NDC31HJ-101XC CAPACITOR100pF 50V J
C314NDC31HJ-101XC CAPACITOR100pF 50V J
C315QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C316QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C317QEKJ1CM-476ZE CAPACITOR47uF 16V M
C318QEKJ1CM-226ZE CAPACITOR22uF 16V M
C319NCB31EK-223XC CAPACITOR0.022uF 25V K
C320NCB31EK-223XC CAPACITOR0.022uF 25V K
C322NCB31EK-104XC CAPACITOR0.1uF 25V K
C323NCB31EK-104XC CAPACITOR0.1uF 25V K
C324NCB31EK-104XC CAPACITOR0.1uF 25V K
C325NCB31EK-104XC CAPACITOR0.1uF 25V K
C341NCB31EK-473XC CAPACITOR0.047uF 25V K
C355QEKJ1CM-107ZE CAPACITOR100uF 16V M
C357NCB31EK-473XC CAPACITOR0.047uF 25V K
Part No.Part NameDescriptionLocal
3-8
Page 41
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
Part No.Part NameDescriptionLocal
C403NCB31HK-103XC CAPACITOR0.01uF 50V K
C404NCB31HK-103XC CAPACITOR0.01uF 50V K
C405QERF1HM-105ZE CAPACITOR1uF 50V M
C406NCB31EK-103XC CAPACITOR0.01uF 25V K
C407QERF1AM-107ZE CAPACITOR100uF 10V M
C408NCB31HK-103XC CAPACITOR0.01uF 50V K
C411QEKJ0JM-107ZE CAPACITOR100uF 6.3V M
C412NCB31HK-103XC CAPACITOR0.01uF 50V K
C413NCB31EK-104XC CAPACITOR0.1uF 25V K
C414NCB31HK-222XC CAPACITOR2200pF 50V K
C415NCB31EK-104XC CAPACITOR0.1uF 25V K
C416QEKJ0JM-107ZE CAPACITOR100uF 6.3V M
C418NCB31HK-103XC CAPACITOR0.01uF 50V K
C419NDC31HJ-7R0XC CAPACITOR7pF 50V J
C420NDC31HJ-8R0XC CAPACITOR8pF 50V J
C421NCB31HK-103XC CAPACITOR0.01uF 50V K
C422QEKJ1AM-107ZE CAPACITOR100uF 10V M
C430NCB31HK-103XC CAPACITOR0.01uF 50V K
C431NDC31HJ-101XC CAPACITOR100pF 50V J
C440NCB31HK-103XC CAPACITOR0.01uF 50V K
C461NCB31EK-104XC CAPACITOR0.1uF 25V K
C462QEKJ0JM-107ZE CAPACITOR100uF 6.3V M
C463QEKJ0JM-107ZE CAPACITOR100uF 6.3V M
C464NCB31EK-104XC CAPACITOR0.1uF 25V K
C481QERF1CM-476ZE CAPACITOR47uF 16V M
C482NCB31EK-104XC CAPACITOR0.1uF 25V K
C483NCB31EK-104XC CAPACITOR0.1uF 25V K
C501QERF1AM-476ZE CAPACITOR47uF 10V M
C502NCB31HK-103XC CAPACITOR0.01uF 50V K
C503QEKJ1AM-107ZE CAPACITOR100uF 10V M
C504NCB31EK-473XC CAPACITOR0.047uF 25V K
C505NCB31EK-473XC CAPACITOR0.047uF 25V K
C506NCB31EK-473XC CAPACITOR0.047uF 25V K
C507NCB31EK-473XC CAPACITOR0.047uF 25V K
C510NCB31EK-103XC CAPACITOR0.01uF 25V K
C512QERF1CM-476ZE CAPACITOR47uF 16V M
C513NCB31EK-103XC CAPACITOR0.01uF 25V K
C514NCB31EK-103XC CAPACITOR0.01uF 25V K
C521NCB31HK-103XC CAPACITOR0.01uF 50V K
C522NCB31HK-103XC CAPACITOR0.01uF 50V K
C523QEKJ1AM-107ZE CAPACITOR100uF 10V M
C524NCB31HK-103XC CAPACITOR0.01uF 50V K
C525QEKJ1AM-107ZE CAPACITOR100uF 10V M
C527NCB31HK-682XC CAPACITOR6800pF 50V K
C528NCB31HK-103XC CAPACITOR0.01uF 50V K
C529QEKJ1AM-107ZE CAPACITOR100uF 10V M
C530NCB31EK-104XC CAPACITOR0.1uF 25V K
C531NCB31EK-104XC CAPACITOR0.1uF 25V K
C532NDC31HJ-680XC CAPACITOR68pF 50V J
C533NCB31HK-103XC CAPACITOR0.01uF 50V K
C534NDC31HJ-5R0XC CAPACITOR5pF 50V J
C541QEKJ1AM-107ZE CAPACITOR100uF 10V M
C542NCB31HK-103XC CAPACITOR0.01uF 50V K
C543QEKJ1HM-105ZE CAPACITOR1uF 50V M
C544QEKJ1AM-107ZE CAPACITOR100uF 10V M
C545NCB31HK-103XC CAPACITOR0.01uF 50V K
C546NDC31HJ-470XC CAPACITOR47pF 50V J
C547NCB31HK-153XC CAPACITOR0.015uF 50V K
C548NCB31HK-103XC CAPACITOR0.01uF 50V K
C549NCB31HK-272XC CAPACITOR2700pF 50V K
C550NCB31HK-103XC CAPACITOR0.01uF 50V K
C551NCB31EK-333XC CAPACITOR0.033uF 25V K
C552NCB31EK-333XC CAPACITOR0.033uF 25V K
C553NCB31EK-473XC CAPACITOR0.047uF 25V K
C554NCB31EK-473XC CAPACITOR0.047uF 25V K
C555NCB31EK-473XC CAPACITOR0.047uF 25V K
C556NCB31HK-471XC CAPACITOR470pF 50V K
C557NCB31HK-471XC CAPACITOR470pF 50V K
C558NCB31EK-473XC CAPACITOR0.047uF 25V K
C559NCB31EK-473XC CAPACITOR0.047uF 25V K
C560NCB31HK-103XC CAPACITOR0.01uF 50V K
C561QEKJ1AM-107ZE CAPACITOR100uF 10V M
C562NCB31HK-103XC CAPACITOR0.01uF 50V K
C565NCB31HK-103XC CAPACITOR0.01uF 50V K
C566QEKJ1AM-107ZE CAPACITOR100uF 10V M
C568NCB31EK-104XC CAPACITOR0.1uF 25V K
C570QERF1AM-476ZE CAPACITOR47uF 10V M
C571NCB31HK-103XC CAPACITOR0.01uF 50V K
C572QERF1AM-107ZE CAPACITOR100uF 10V M
C580QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C581NCB31HK-332XC CAPACITOR3300pF 50V K
C582NDC31HJ-271XC CAPACITOR270pF 50V J
C583NDC31HJ-271XC CAPACITOR270pF 50V J
C584NCB31EK-104XC CAPACITOR0.1uF 25V K
C585QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C589QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C590QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C591NCB31HK-332XC CAPACITOR3300pF 50V K
C592NDC31HJ-271XC CAPACITOR270pF 50V J
C593NDC31HJ-271XC CAPACITOR270pF 50V J
C594NCB31EK-104XC CAPACITOR0.1uF 25V K
C595QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C596QEKJ1AM-107ZE CAPACITOR100uF 10V M
C597NCB31HK-103XC CAPACITOR0.01uF 50V K
C599QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C701NDC31HJ-270XC CAPACITOR27pF 50V J
C702NDC31HJ-220XC CAPACITOR22pF 50V J
C703NDC31HJ-270XC CAPACITOR27pF 50V J
C704NDC31HJ-8R0XC CAPACITOR8pF 50V J
C705NCB31EK-473XC CAPACITOR0.047uF 25V K
C706NCB31EK-473XC CAPACITOR0.047uF 25V K
C707NCB31EK-104XC CAPACITOR0.1uF 25V K
C708NCB31EK-473XC CAPACITOR0.047uF 25V K
C709NCB31EK-104XC CAPACITOR0.1uF 25V K
C710QERF0JM-476ZE CAPACITOR47uF 6.3V M
C711QEKJ0JM-227ZE CAPACITOR220uF 6.3V M
C712NCB31HK-103XC CAPACITOR0.01uF 50V K
C713NCB31EK-104XC CAPACITOR0.1uF 25V K
C716NCB31EK-104XC CAPACITOR0.1uF 25V K
C717NCB31EK-104XC CAPACITOR0.1uF 25V K
C718NCB31EK-104XC CAPACITOR0.1uF 25V K
C770NCB31EK-473XC CAPACITOR0.047uF 25V K
C771NCB31EK-473XC CAPACITOR0.047uF 25V K
C772NCB31EK-104XC CAPACITOR0.1uF 25V K
C781QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C783NCB31EK-823XC CAPACITOR0.082uF 25V K
C784QEKJ1CM-107ZE CAPACITOR100uF 16V M
C801NCB31AK-334XC CAPACITOR0.33uF 10V K
C851QEKJ1CM-106ZE CAPACITOR10uF 16V M
C852NCB31HK-103XC CAPACITOR0.01uF 50V K
C901QEZ0676-338E CAPACITOR3300uF
C902QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C903QEKJ1CM-226ZE CAPACITOR22uF 16V M
C904QEKJ1CM-106ZE CAPACITOR10uF 16V M
C905QEKJ1CM-476ZE CAPACITOR47uF 16V M
C906NCB31HK-103XC CAPACITOR0.01uF 50V K
C907QEKJ1AM-227ZE CAPACITOR220uF 10V M
C908QEKJ1AM-227ZE CAPACITOR220uF 10V M
C909QEKJ1AM-227ZE CAPACITOR220uF 10V M
C910QEKJ1CM-476ZE CAPACITOR47uF 16V M
C911NCB31CK-104XC CAPACITOR0.1uF 16V K
C912NCB31HK-103XC CAPACITOR0.01uF 50V K
C913QEKJ1CM-106ZE CAPACITOR10uF 16V M
C914QEKJ1CM-107ZE CAPACITOR100uF 16V M
C915NCB31CK-104XC CAPACITOR0.1uF 16V K
C919QEKJ1CM-106ZE CAPACITOR10uF 16V M
C961NDC31HJ-101XC CAPACITOR100pF 50V J
C962NDC31HJ-101XC CAPACITOR100pF 50V J
C963NDC31HJ-101XC CAPACITOR100pF 50V J
C964NDC31HJ-101XC CAPACITOR100pF 50V J
C965NDC31HJ-101XC CAPACITOR100pF 50V J
C966NDC31HJ-101XC CAPACITOR100pF 50V J
C967NDC31HJ-101XC CAPACITOR100pF 50V J
C968NDC31HJ-101XC CAPACITOR100pF 50V J
C971NCB31EK-104XC CAPACITOR0.1uF 25V K
L1QQL244J-4R7ZCOIL4.7uH J
L401NQL114K-470XINDUCTOR47uH K
L402NQL114K-470XINDUCTOR47uH K
L404NQL114K-470XINDUCTOR47uH K
L541NQL114K-470XINDUCTOR47uH K
L543NQL114K-470XINDUCTOR47uH K
L544NQL114K-470XINDUCTOR47uH K
L701QQL244J-4R7ZCOIL4.7uH J
L702NQL79GM-4R7XCOIL4.7uH M
L901QQR0703-001CHOKE COIL
CN501QGB2027M4-22SCONNECTOR B-B (1-22)
CN701QGZ1601J1-15CONNECTOR (1-15)
CN901QNZ0611-00116P CONNECTOR
J1QNB0100-002CAR ANT JACK
J321QNN0519-001PIN JACK
TU1QAU0312-002TUNER PACK
X31QAX0616-001ZCRYSTAL10.250MHz
X401QAX0413-001ZCRYSTAL16.9344MHz
X701QAX0617-001ZCRYSTAL12.500MHz
X702QAX0401-001CRYSTAL32.768KHz
C601NCB31HK-223XC CAPACITOR0.022uF 50V K
C602NCS31HJ-681XC CAPACITOR680pF 50V J
C603NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C612NBE20JM-475XTA E CAPACITOR4.7uF 6.3V M
IC161TEA6320T-XIC
IC301LA47516POWER IC
IC501AN41012A-WIC
IC521MN6627945ECUCIC
IC523SN74LVC07ANS-XLOGIC IC
IC581NJM4565M-WEIC
IC701LC723784-9C90IC
IC901AN80T71REGULATOR IC
IC981NJU7772F15-XIC
C1NDC31HJ-221XC CAPACITOR220pF 50V J
C2QEKJ1CM-476ZE CAPACITOR47uF 16V M
C3QEKJ1HM-104ZE CAPACITOR0.1uF 50V M
C4NCB31EK-223XC CAPACITOR0.022uF 25V K
C6NCB31EK-103XC CAPACITOR0.01uF 25V K
C7QEKJ1HM-104ZE CAPACITOR0.1uF 50V M
C8NDC31HJ-121XC CAPACITOR120pF 50V J
C9QEKJ1AM-227ZE CAPACITOR220uF 10V M
C10QEKJ1HM-104ZE CAPACITOR0.1uF 50V M
C11NCB31HK-331XC CAPACITOR330pF 50V K
C31QEKJ1AM-227ZE CAPACITOR220uF 10V M
C32NCB31HK-102XC CAPACITOR1000pF 50V K
C33QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C81NCB31EK-153XC CAPACITOR0.015uF 25V K
C82NCB31HK-562XC CAPACITOR5600pF 50V K
C83QEKJ1HM-105ZE CAPACITOR1uF 50V M
Page 45
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
Part No.Part NameDescriptionLocal
C91NCB31EK-153XC CAPACITOR0.015uF 25V K
C92NCB31HK-562XC CAPACITOR5600pF 50V K
C93QEKJ1HM-105ZE CAPACITOR1uF 50V M
C96NCB31EK-104XC CAPACITOR0.1uF 25V K
C99NCB31EK-104XC CAPACITOR0.1uF 25V K
C161NCB31HK-822XC CAPACITOR8200pF 50V K
C162NCB31CK-224XC CAPACITOR0.22uF 16V K
C163NCB21CK-224XC CAPACITOR0.22uF 16V K
C164NCB31EK-333XC CAPACITOR0.033uF 25V K
C165NCB31HK-562XC CAPACITOR5600pF 50V K
C166QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C167QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C168QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C169QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C171NCB31HK-822XC CAPACITOR8200pF 50V K
C172NCB31CK-224XC CAPACITOR0.22uF 16V K
C173NCB21CK-224XC CAPACITOR0.22uF 16V K
C174NCB31EK-333XC CAPACITOR0.033uF 25V K
C175NCB31HK-562XC CAPACITOR5600pF 50V K
C176QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C177QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C178QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C179QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C183QTE1H54-225ZE CAPACITOR2.2uF 50V
C184QTE1H54-225ZE CAPACITOR2.2uF 50V
C191QEKJ1AM-107ZE CAPACITOR100uF 10V M
C192NCB31HK-103XC CAPACITOR0.01uF 50V K
C193QEKJ1AM-107ZE CAPACITOR100uF 10V M
C194QEKJ1CM-476ZE CAPACITOR47uF 16V M
C195NCB31EK-104XC CAPACITOR0.1uF 25V K
C301QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C302QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C303NCB31HK-223XC CAPACITOR0.022uF 50V K
C304NCB31HK-223XC CAPACITOR0.022uF 50V K
C305NCB31EK-104XC CAPACITOR0.1uF 25V K
C306NCB31EK-104XC CAPACITOR0.1uF 25V K
C307NCB31EK-104XC CAPACITOR0.1uF 25V K
C308NCB31EK-104XC CAPACITOR0.1uF 25V K
C309QEKJ1CM-107ZE CAPACITOR100uF 16V M
C310QEKJ1CM-476ZE CAPACITOR47uF 16V M
C311QERF1CM-226ZE CAPACITOR22uF 16V M
C312NDC31HJ-101XC CAPACITOR100pF 50V J
C313NDC31HJ-101XC CAPACITOR100pF 50V J
C314NDC31HJ-101XC CAPACITOR100pF 50V J
C315NDC31HJ-101XC CAPACITOR100pF 50V J
C317QERF1HM-105ZE CAPACITOR1uF 50V M
C318QEKJ1HM-105ZE CAPACITOR1uF 50V M
C319NCB31EK-223XC CAPACITOR0.022uF 25V K
C341NDC31HJ-101XC CAPACITOR100pF 50V J
C351NDC31HJ-101XC CAPACITOR100pF 50V J
C501QEKJ0JM-227ZE CAPACITOR220uF 6.3V M
C502NCB31EK-104XC CAPACITOR0.1uF 25V K
C503QEKJ1AM-107ZE CAPACITOR100uF 10V M
C504NCB31EK-104XC CAPACITOR0.1uF 25V K
C505QEKJ1AM-227ZE CAPACITOR220uF 10V M
C506NCB31EK-103XC CAPACITOR0.01uF 25V K
C511NCB31HK-222XC CAPACITOR2200pF 50V K
C513NCB31HK-682XC CAPACITOR6800pF 50V K
C515NCB31HK-122XC CAPACITOR1200pF 50V K
C517NCB31HK-182XC CAPACITOR1800pF 50V K
C518NDC31HJ-680XC CAPACITOR68pF 50V J
C521NCB31EK-104XC CAPACITOR0.1uF 25V K
C522NCB31CK-224XC CAPACITOR0.22uF 16V K
C523NDC31HJ-101XC CAPACITOR100pF 50V J
C524NDC31HJ-561XC CAPACITOR560pF 50V J
C525NCB31HK-223XC CAPACITOR0.022uF 50V K
C526NCB31HK-223XC CAPACITOR0.022uF 50V K
C527NCB31EK-332XC CAPACITOR3300pF 25V K
C528NDC31HJ-331XC CAPACITOR330pF 50V J
C531NCB31AK-334XC CAPACITOR0.33uF 10V K
C532NCB31AK-334XC CAPACITOR0.33uF 10V K
C533QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C534NCB31EK-332XC CAPACITOR3300pF 25V K
C535NCB31EK-104XC CAPACITOR0.1uF 25V K
C536QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C537QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C538QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C539NCB31EK-104XC CAPACITOR0.1uF 25V K
C540NCS31HJ-681XC CAPACITOR680pF 50V J
C541NCB31EK-153XC CAPACITOR0.015uF 25V K
C542NCB31EK-104XC CAPACITOR0.1uF 25V K
C543NCB31HK-102XC CAPACITOR1000pF 50V K
C544NCB31EK-823XC CAPACITOR0.082uF 25V K
C545NCB31EK-104XC CAPACITOR0.1uF 25V K
C546QEKJ0JM-227ZE CAPACITOR220uF 6.3V M
C547QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C548QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C549NCB31EK-104XC CAPACITOR0.1uF 25V K
C550NCB31EK-104XC CAPACITOR0.1uF 25V K
C551NCB31EK-104XC CAPACITOR0.1uF 25V K
C552QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C553QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C554NCB31EK-103XC CAPACITOR0.01uF 25V K
C571QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C572NCB31EK-104XC CAPACITOR0.1uF 25V K
C573QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C574NCB31EK-104XC CAPACITOR0.1uF 25V K
C583NDC31HJ-821XC CAPACITOR820pF 50V J
C584NDC31HJ-821XC CAPACITOR820pF 50V J
C585QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C586QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C587NDC31HJ-101XC CAPACITOR100pF 50V J
C588NDC31HJ-101XC CAPACITOR100pF 50V J
C589QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C590QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C591QEKJ1CM-107ZE CAPACITOR100uF 16V M
C592NCB31EK-104XC CAPACITOR0.1uF 25V K
C701QEKJ0JM-227ZE CAPACITOR220uF 6.3V M
C702NCB31EK-103XC CAPACITOR0.01uF 25V K
C703NDC31HJ-220XC CAPACITOR22pF 50V J
C704NDC31HJ-270XC CAPACITOR27pF 50V J
C705QEKJ1CM-106ZE CAPACITOR10uF 16V M
C706NDC31HJ-221XC CAPACITOR220pF 50V J
C711NCB31EK-104XC CAPACITOR0.1uF 25V K
C712NCB31EK-104XC CAPACITOR0.1uF 25V K
C713NCB31EK-104XC CAPACITOR0.1uF 25V K
C715NCB31EK-104XC CAPACITOR0.1uF 25V K
C716NCB31EK-104XC CAPACITOR0.1uF 25V K
C781QEKJ0JM-227ZE CAPACITOR220uF 6.3V M
C782QEKJ1CM-476ZE CAPACITOR47uF 16V M
C783NCB31EK-823XC CAPACITOR0.082uF 25V K
C801NCB31EK-104XC CAPACITOR0.1uF 25V K
C901QEZ0676-338E CAPACITOR3300uF
C902NCB31HK-103XC CAPACITOR0.01uF 50V K
C903QEKJ1CM-226ZE CAPACITOR22uF 16V M
C904QEKJ1CM-226ZE CAPACITOR22uF 16V M
C905QEKJ1CM-226ZE CAPACITOR22uF 16V M
C906NCB31EK-104XC CAPACITOR0.1uF 25V K
C907NCB31HK-103XC CAPACITOR0.01uF 50V K
C908QEKJ1AM-107ZE CAPACITOR100uF 10V M
C909QEKJ1AM-107ZE CAPACITOR100uF 10V M
C910NCB31HK-103XC CAPACITOR0.01uF 50V K
C911QEKJ1AM-227ZE CAPACITOR220uF 10V M
C913NCB31CK-224XC CAPACITOR0.22uF 16V K
C914NCB31EK-104XC CAPACITOR0.1uF 25V K
C915QEKJ1CM-107ZE CAPACITOR100uF 16V M
C916QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C919QEKJ1CM-106ZE CAPACITOR10uF 16V M
C971QEKJ0JM-107ZE CAPACITOR100uF 6.3V M
C972NCB31EK-104XC CAPACITOR0.1uF 25V K
C983QEKJ0JM-107ZE CAPACITOR100uF 6.3V M
C984NCB31EK-104XC CAPACITOR0.1uF 25V K
C601NCB31HK-223XC CAPACITOR0.022uF 50V K
C602NCS31HJ-681XC CAPACITOR680pF 50V J
C603NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C612NBE20JM-475XTA E CAPACITOR4.7uF 6.3V M
IC31TB2118F-XPLL IC
IC161TEA6320T-XIC
IC301LA47516POWER IC
IC401TC94A34FG-002IC
IC461NJU7772F15-XIC
IC481AK4385ET-XIC
IC501LA6242H-XIC
IC521TA2157FN-XRF AMP IC
IC541TC94A14FACD LSI IC
IC581NJM4565M-WEIC
IC701UPD784217AGC302IC
IC702IC-PST3433U-XIC
IC901AN80T07AREGULATOR IC
C1QEKJ1CM-226ZE CAPACITOR22uF 16V M
C2NCB31EK-473XC CAPACITOR0.047uF 25V K
C3NCB31EK-103XC CAPACITOR0.01uF 25V K
C4QEKJ1AM-227ZE CAPACITOR220uF 10V M
C5QERF1HM-104ZE CAPACITOR0.1uF 50V M
C6NCB31HK-103XC CAPACITOR0.01uF 50V K
Part No.Part NameDescriptionLocal
Symbol No.
C7QEKJ1CM-226ZE CAPACITOR22uF 16V M
C31QEKJ1AM-107ZE CAPACITOR100uF 10V M
C32NDC31HJ-470XC CAPACITOR47pF 50V J
C33QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C34NCB31EK-473XC CAPACITOR0.047uF 25V K
C35NDC31HJ-100XC CAPACITOR10pF 50V J
C36NDC31HJ-7R0XC CAPACITOR7pF 50V J
C37NDC31HJ-100XC CAPACITOR10pF 50V J
C38NCB31HK-102XC CAPACITOR1000pF 50V K
C39NCB31HK-102XC CAPACITOR1000pF 50V K
C40QEKJ1CM-106ZE CAPACITOR10uF 16V M
C41NCB31EK-473XC CAPACITOR0.047uF 25V K
C42NCB31HK-103XC CAPACITOR0.01uF 50V K
C43QFV61HJ-473ZMF CAPACITOR0.047uF 50V J
C44NCB31HK-103XC CAPACITOR0.01uF 50V K
C45NCB31HK-272XC CAPACITOR2700pF 50V K
C46NCB31HK-103XC CAPACITOR0.01uF 50V K
C47NCB31HK-103XC CAPACITOR0.01uF 50V K
C48NCB31EK-473XC CAPACITOR0.047uF 25V K
C49NCB31HK-102XC CAPACITOR1000pF 50V K
C50NDC31HJ-101XC CAPACITOR100pF 50V J
C51NDC31HJ-331XC CAPACITOR330pF 50V J
C81QEKJ1HM-105ZE CAPACITOR1uF 50V M
C82NCB31HK-332XC CAPACITOR3300pF 50V K
C84NCB31HK-153XC CAPACITOR0.015uF 50V K
C91QEKJ1HM-105ZE CAPACITOR1uF 50V M
C92NCB31HK-332XC CAPACITOR3300pF 50V K
C94NCB31HK-153XC CAPACITOR0.015uF 50V K
C95NCB31HK-103XC CAPACITOR0.01uF 50V K
C161QTE1H54-225ZE CAPACITOR2.2uF 50V
C162QEKJ1HM-105ZE CAPACITOR1uF 50V M
C164NCB31HK-822XC CAPACITOR8200pF 50V K
C165NCB31AK-224XC CAPACITOR0.22uF 10V K
C166NCB21CK-224XC CAPACITOR0.22uF 16V K
C167NCB31EK-333XC CAPACITOR0.033uF 25V K
C168NCB31HK-562XC CAPACITOR5600pF 50V K
C169QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C170QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C171QTE1H54-225ZE CAPACITOR2.2uF 50V
C172QEKJ1HM-105ZE CAPACITOR1uF 50V M
C174NCB31HK-822XC CAPACITOR8200pF 50V K
C175NCB31AK-224XC CAPACITOR0.22uF 10V K
C176NCB21CK-224XC CAPACITOR0.22uF 16V K
C177NCB31EK-333XC CAPACITOR0.033uF 25V K
C178NCB31HK-562XC CAPACITOR5600pF 50V K
C179QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C180QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C191QEKJ1CM-476ZE CAPACITOR47uF 16V M
C192QEKJ1AM-107ZE CAPACITOR100uF 10V M
C193QEKJ1AM-107ZE CAPACITOR100uF 10V M
C194NCB31EK-823XC CAPACITOR0.082uF 25V K
C301QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C302QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C303NDC31HJ-101XC CAPACITOR100pF 50V J
C304NDC31HJ-101XC CAPACITOR100pF 50V J
C307QEKJ1HM-105ZE CAPACITOR1uF 50V M
C308QEKJ1HM-105ZE CAPACITOR1uF 50V M
C311QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C312QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C313NDC31HJ-101XC CAPACITOR100pF 50V J
C314NDC31HJ-101XC CAPACITOR100pF 50V J
C315QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C316QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C317QEKJ1CM-476ZE CAPACITOR47uF 16V M
C318QEKJ1CM-226ZE CAPACITOR22uF 16V M
C319NCB31EK-223XC CAPACITOR0.022uF 25V K
C320NCB31EK-223XC CAPACITOR0.022uF 25V K
C322NCB31EK-104XC CAPACITOR0.1uF 25V K
C323NCB31EK-104XC CAPACITOR0.1uF 25V K
C324NCB31EK-104XC CAPACITOR0.1uF 25V K
C325NCB31EK-104XC CAPACITOR0.1uF 25V K
C341NCB31EK-473XC CAPACITOR0.047uF 25V K
C355QEKJ1CM-107ZE CAPACITOR100uF 16V M
C357NCB31EK-473XC CAPACITOR0.047uF 25V K
C403NCB31HK-103XC CAPACITOR0.01uF 50V K
C404NCB31HK-103XC CAPACITOR0.01uF 50V K
C405QERF1HM-105ZE CAPACITOR1uF 50V M
C406NCB31EK-103XC CAPACITOR0.01uF 25V K
Part No.Part NameDescriptionLocal
3-16
Page 49
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
Part No.Part NameDescriptionLocal
C407QERF1AM-107ZE CAPACITOR100uF 10V M
C408NCB31HK-103XC CAPACITOR0.01uF 50V K
C411QEKJ0JM-107ZE CAPACITOR100uF 6.3V M
C412NCB31HK-103XC CAPACITOR0.01uF 50V K
C413NCB31EK-104XC CAPACITOR0.1uF 25V K
C414NCB31HK-222XC CAPACITOR2200pF 50V K
C415NCB31EK-104XC CAPACITOR0.1uF 25V K
C416QEKJ0JM-107ZE CAPACITOR100uF 6.3V M
C418NCB31HK-103XC CAPACITOR0.01uF 50V K
C419NDC31HJ-7R0XC CAPACITOR7pF 50V J
C420NDC31HJ-8R0XC CAPACITOR8pF 50V J
C421NCB31HK-103XC CAPACITOR0.01uF 50V K
C422QEKJ1AM-107ZE CAPACITOR100uF 10V M
C430NCB31HK-103XC CAPACITOR0.01uF 50V K
C431NDC31HJ-101XC CAPACITOR100pF 50V J
C440NCB31HK-103XC CAPACITOR0.01uF 50V K
C461NCB31EK-104XC CAPACITOR0.1uF 25V K
C462QEKJ0JM-107ZE CAPACITOR100uF 6.3V M
C463QEKJ0JM-107ZE CAPACITOR100uF 6.3V M
C464NCB31EK-104XC CAPACITOR0.1uF 25V K
C481QERF1CM-476ZE CAPACITOR47uF 16V M
C482NCB31EK-104XC CAPACITOR0.1uF 25V K
C483NCB31EK-104XC CAPACITOR0.1uF 25V K
C501QEKJ1CM-476ZE CAPACITOR47uF 16V M
C502NCB31HK-103XC CAPACITOR0.01uF 50V K
C503QEKJ1AM-107ZE CAPACITOR100uF 10V M
C504NCB31EK-473XC CAPACITOR0.047uF 25V K
C505NCB31EK-473XC CAPACITOR0.047uF 25V K
C506NCB31EK-473XC CAPACITOR0.047uF 25V K
C507NCB31EK-473XC CAPACITOR0.047uF 25V K
C510NCB31EK-103XC CAPACITOR0.01uF 25V K
C512QERF1CM-476ZE CAPACITOR47uF 16V M
C513NCB31EK-103XC CAPACITOR0.01uF 25V K
C514NCB31EK-103XC CAPACITOR0.01uF 25V K
C521NCB31HK-103XC CAPACITOR0.01uF 50V K
C522NCB31HK-103XC CAPACITOR0.01uF 50V K
C523QEKJ1AM-107ZE CAPACITOR100uF 10V M
C524NCB31HK-103XC CAPACITOR0.01uF 50V K
C525QEKJ1AM-107ZE CAPACITOR100uF 10V M
C527NCB31HK-682XC CAPACITOR6800pF 50V K
C528NCB31HK-103XC CAPACITOR0.01uF 50V K
C529QEKJ1AM-107ZE CAPACITOR100uF 10V M
C530NCB31EK-104XC CAPACITOR0.1uF 25V K
C531NCB31EK-104XC CAPACITOR0.1uF 25V K
C532NDC31HJ-680XC CAPACITOR68pF 50V J
C533NCB31HK-103XC CAPACITOR0.01uF 50V K
C534NDC31HJ-5R0XC CAPACITOR5pF 50V J
C541QEKJ1AM-107ZE CAPACITOR100uF 10V M
C542NCB31HK-103XC CAPACITOR0.01uF 50V K
C543QEKJ1HM-105ZE CAPACITOR1uF 50V M
C544QEKJ1AM-107ZE CAPACITOR100uF 10V M
C545NCB31HK-103XC CAPACITOR0.01uF 50V K
C546NDC31HJ-470XC CAPACITOR47pF 50V J
C547NCB31HK-153XC CAPACITOR0.015uF 50V K
C548NCB31HK-103XC CAPACITOR0.01uF 50V K
C549NCB31HK-272XC CAPACITOR2700pF 50V K
C550NCB31HK-103XC CAPACITOR0.01uF 50V K
C551NCB31EK-333XC CAPACITOR0.033uF 25V K
C552NCB31EK-333XC CAPACITOR0.033uF 25V K
C553NCB31EK-473XC CAPACITOR0.047uF 25V K
C554NCB31EK-473XC CAPACITOR0.047uF 25V K
C555NCB31EK-473XC CAPACITOR0.047uF 25V K
C556NCB31HK-471XC CAPACITOR470pF 50V K
C557NCB31HK-471XC CAPACITOR470pF 50V K
C558NCB31EK-473XC CAPACITOR0.047uF 25V K
C559NCB31EK-473XC CAPACITOR0.047uF 25V K
C560NCB31HK-103XC CAPACITOR0.01uF 50V K
C561QEKJ1AM-107ZE CAPACITOR100uF 10V M
C562NCB31HK-103XC CAPACITOR0.01uF 50V K
C565NCB31HK-103XC CAPACITOR0.01uF 50V K
C566QEKJ1AM-107ZE CAPACITOR100uF 10V M
C568NCB31EK-104XC CAPACITOR0.1uF 25V K
C570QERF1AM-476ZE CAPACITOR47uF 10V M
C571NCB31HK-103XC CAPACITOR0.01uF 50V K
C572QERF1AM-107ZE CAPACITOR100uF 10V M
C580QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C581NCB31HK-332XC CAPACITOR3300pF 50V K
C582NDC31HJ-271XC CAPACITOR270pF 50V J
C583NDC31HJ-271XC CAPACITOR270pF 50V J
C584NCB31EK-104XC CAPACITOR0.1uF 25V K
C585QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C589QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C590QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C591NCB31HK-332XC CAPACITOR3300pF 50V K
C592NDC31HJ-271XC CAPACITOR270pF 50V J
C593NDC31HJ-271XC CAPACITOR270pF 50V J
C594NCB31EK-104XC CAPACITOR0.1uF 25V K
C595QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C596QEKJ1AM-107ZE CAPACITOR100uF 10V M
C597NCB31HK-103XC CAPACITOR0.01uF 50V K
C599QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C701NDC31HJ-220XC CAPACITOR22pF 50V J
C702NDC31HJ-270XC CAPACITOR27pF 50V J
C703NDC31HJ-270XC CAPACITOR27pF 50V J
C704NDC31HJ-8R0XC CAPACITOR8pF 50V J
C705NCB31EK-473XC CAPACITOR0.047uF 25V K
C706NCB31EK-473XC CAPACITOR0.047uF 25V K
C707NCB31EK-104XC CAPACITOR0.1uF 25V K
C708NCB31EK-473XC CAPACITOR0.047uF 25V K
C709NCB31EK-104XC CAPACITOR0.1uF 25V K
C710QERF0JM-476ZE CAPACITOR47uF 6.3V M
C711QEKJ0JM-227ZE CAPACITOR220uF 6.3V M
C712NCB31HK-103XC CAPACITOR0.01uF 50V K
C713NCB31EK-104XC CAPACITOR0.1uF 25V K
C716NCB31EK-104XC CAPACITOR0.1uF 25V K
C717NCB31EK-104XC CAPACITOR0.1uF 25V K
C718NCB31EK-104XC CAPACITOR0.1uF 25V K
C770NCB31EK-473XC CAPACITOR0.047uF 25V K
C771NDC31HJ-101XC CAPACITOR100pF 50V J
C772NCB31EK-104XC CAPACITOR0.1uF 25V K
C781QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C783NCB31EK-823XC CAPACITOR0.082uF 25V K
C784QEKJ1CM-107ZE CAPACITOR100uF 16V M
C801NCB31AK-334XC CAPACITOR0.33uF 10V K
C851QEKJ1CM-106ZE CAPACITOR10uF 16V M
C852NCB31HK-103XC CAPACITOR0.01uF 50V K
C901QEZ0676-338E CAPACITOR3300uF
C902QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C903QEKJ1CM-226ZE CAPACITOR22uF 16V M
C904QEKJ1CM-106ZE CAPACITOR10uF 16V M
C905QEKJ1CM-476ZE CAPACITOR47uF 16V M
C906NCB31HK-103XC CAPACITOR0.01uF 50V K
C907QEKJ1AM-227ZE CAPACITOR220uF 10V M
C908QEKJ1AM-227ZE CAPACITOR220uF 10V M
C909QEKJ1AM-227ZE CAPACITOR220uF 10V M
C910QEKJ1CM-476ZE CAPACITOR47uF 16V M
C911NCB31CK-104XC CAPACITOR0.1uF 16V K
C912NCB31HK-103XC CAPACITOR0.01uF 50V K
C913QEKJ1CM-106ZE CAPACITOR10uF 16V M
C914QEKJ1CM-107ZE CAPACITOR100uF 16V M
C915NCB31CK-104XC CAPACITOR0.1uF 16V K
C919QEKJ1CM-106ZE CAPACITOR10uF 16V M
C961NDC31HJ-101XC CAPACITOR100pF 50V J
C962NDC31HJ-101XC CAPACITOR100pF 50V J
C963NDC31HJ-101XC CAPACITOR100pF 50V J
C964NDC31HJ-101XC CAPACITOR100pF 50V J
C965NDC31HJ-101XC CAPACITOR100pF 50V J
C966NDC31HJ-101XC CAPACITOR100pF 50V J
C967NDC31HJ-101XC CAPACITOR100pF 50V J
C968NDC31HJ-101XC CAPACITOR100pF 50V J
C971NCB31EK-104XC CAPACITOR0.1uF 25V K
L1QQL244J-4R7ZCOIL4.7uH J
L401NQL114K-470XINDUCTOR47uH K
L402NQL114K-470XINDUCTOR47uH K
L404NQL114K-470XINDUCTOR47uH K
L541NQL114K-470XINDUCTOR47uH K
L543NQL114K-470XINDUCTOR47uH K
L544NQL114K-470XINDUCTOR47uH K
L701QQL244J-4R7ZCOIL4.7uH J
L702NQL79GM-4R7XCOIL4.7uH M
L901QQR0703-001CHOKE COIL
CN501QGB2027M4-22SCONNECTOR B-B (1-22)
CN701QGZ1601J1-15CONNECTOR (1-15)
CN901QNZ0611-00116P CONNECTOR
J1QNB0100-002CAR ANT JACK
J321QNN0519-001PIN JACK
TU1QAU0223-001TUNER
X31QAX0616-001ZCRYSTAL10.250MHz
X401QAX0413-001ZCRYSTAL16.9344MHz
X701QAX0617-001ZCRYSTAL12.500MHz
X702QAX0401-001CRYSTAL32.768KHz
C601NCB31HK-223XC CAPACITOR0.022uF 50V K
C602NCS31HJ-681XC CAPACITOR680pF 50V J
C603NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C612NBE20JM-475XTA E CAPACITOR4.7uF 6.3V M
A 3GET0259-002BINST BOOKKOR CHI(TAIWAN) ARA PER
A 3GET0259-002AINST BOOKKOR CHI(TAIWAN) ARA PER
A 4GET0259-001BINST BOOKENG THA
A 4GET0259-001AINST BOOKENG THA
A 4GET0259-003BINST BOOKENG INA
A 4GET0259-003AINST BOOKENG INA
A 4GET0259-007AINST BOOKENG CHI(TAIWAN)
A 4GET0259-007BINST BOOKENG CHI(TAIWAN)
A 5GET0259-009BINST BOOKRUS
A 5GET0259-009AINST BOOKRUS
A 6GET0259-004AINSTALL MANUAL
A 6GET0259-006AINSTALL MANUAL
A 6GET0259-008AINSTALL MANUAL
A 7GET0259-005AINSTALL MANUAL
A 8GET0259-010AINSTALL MANUAL
A 9VKZ4027-202PLUG NUT
A 10VKH4871-003MOUNT BOLT
A 11VKZ4328-003LOCK NUT
A 12QYWWS53A008ZAWASHER0mm/5.3mm x
A 13GE40130-002AHOOK(x2)
A 14FSJB3002-00CHARD CASE
A 15RM-RK50REMOCON UNIT
A 16------------BATTERY
A 17QAM0390-00416P CORD ASSY
KITSRW-385USCREW PART KITA9 A10 A11 A12 A13
P 1QPC03004315PPOLY BAG30cm x 43cm
P 2FSPG4002-001POLY BAG(x2)
P 2FSPG4002-001POLY BAG
P 3QPA00801205POLY BAG8cm x 12cm
P 4GE10070-003AEPS CUSHION
P 5GE31435-002ACARTON
P 5GE31438-002ACARTON
P 6QPA01003003POLY BAG10cm x 30cm
P 7FSYH4036-068SHEET
UT ------------------------ Taiwan
UH --------------------- Thailand
UN ------------------- Indonesia
U ------------------- Other Areas
KD-G415KD-G416
CONTROL PANELBLACKSILVER
Contents
Block diagram (for UT,UH,UN and U version)
Standard schematic diagrams (for UT,UH,UN and U version)
Printed circuit boards (for UT,UH,UN and U version)
Block diagram (for UT2,UH2,UN2 and U2 version)
Standard schematic diagrams (for UT2,UH2,UN2 and U2 version)
Printed circuit boards (for UT2,UH2,UN2 and U2 version)
Block diagram (for UH3, UN3 and U3 version)
Standard schematic diagrams (for UH3, UN3 and U3 version)
Printed circuit boards (for UH3, UN3 and U3 version)
COPYRIGHT 2005 Victor Company of Japan, Limited.
2-1
2-2
2-5
2-6
2-7
2-10
2-11
2-12
2-15 to 17
No.MA136SCH
2005/4
Page 57
Safety precaution
!
!
Burrs formed during molding may be left over on some parts of the chassis. Therefore,
pay attention to such burrs in the case of preforming repair of this system.
Please use enough caution not to see the beam directly or touch it in case of an
adjustment or operation check.