JVC KD-DV5506, KD-DV5505, KD-DV5504 Instructions Manual
DVD/CD RECEIVER
INSTRUCTIONS
For canceling the display demonstration, see page 10.
For installation and connections, refer to the separate manual.
KD-DV5506/
KD-DV5505/KD-DV5504
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best
possible performance from the unit.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to
qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical
instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
For safety...
[European Union only]
This mark is used to indicate...
Turn the control dial to make a
selection, then press to confirm the
selection.
Indication language:
In this manual, English indications are used
for purposes of explanation. You can select
the indication language on the monitor on the
“LANGUAGE” setting (see page 42).
• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operations.
Temperature inside the car...
If you have parked the car for a long time in hot or cold
weather, wait until the temperature in the car becomes
normal before operating the unit.
Caution on volume setting:
Digital devices (CD/USB) produce very little noise
compared with other sources. Lower the volume before
playing these digital sources to avoid damaging the
speakers by sudden increase of the output level.
2
Detaching the control panel
Attaching the control panel
How to reset your unit
WARNINGS:
(To prevent accidents and damage)
• DO NOT install any unit or wire any cable in
a location where;
– it may obstruct the steering wheel and
gearshift lever operations.
– it may obstruct the operation of safety
devices such as air bags.
– it may obstruct visibility.
• DO NOT operate the unit while driving.
• If you need to operate the unit while
driving, be sure to look around carefully.
• The driver must not watch the monitor
while driving.
If the parking brake is not engaged,
“DRIVER MUST NOT WATCH THE MONITOR
WHILE DRIVING.” appears on the monitor,
and no playback picture will be shown.
– This warning appears only when the
parking brake lead is connected to the
parking brake system built in the car
(refer to the Installation/Connection
Manual).
• Your preset adjustments will also be erased (except the
registered Bluetooth device, see page 24).
How to forcibly eject a disc
• You can forcibly eject the loaded disc even if the disc is
locked. To lock/unlock the disc, see page 13.
• Be careful not to drop the disc when it ejects.
• If this does not work, reset your unit.
3
Playable disc type
Disc type Recording format, file type, etc Playable
DVD DVD-Video *
Region Code: South East Asia, Hong Kong region: 3
Australia: 4
India: 5
Ex.:
DVD-Audio/DVD-ROM
DVD Recordable/Rewritable
(DVD-R/-RW *2, +R/+RW *3)
• DVD Video: UDF bridge
• DVD-VR
• DivX/MPEG-1/MPEG-2/MP3/
WMA/WAV: ISO 9660 level 1,
level 2, Romeo, Joliet
Dual Disc DVD side
CD/VCD Audio CD/CD Text (CD-DA)
DVD-Video
DVD-VR
DivX/MPEG1/MPEG2
MP3/WMA/WAV
AAC/JPEG/MPEG4/DVD+VR/DVD-RAM
Non-DVD side
1
VCD (Video CD)
DTS-CD/SVCD (Super Video CD)/CD-ROM/
CD-I (CD-I Ready)
CD Recordable/Rewritable
(CD-R/-RW)
• ISO 9660 level 1, level 2, Romeo,
Joliet
*1 If you insert a DVD Video disc of an incorrect Region Code, “REGION CODE ERROR” appears on the monitor.
*2 DVD-R recorded in multi-border format is also playable (except for dual layer discs). DVD-RW dual layer discs are not
playable.
*3 It is possible to play back finalized +R/+RW (Video format only) discs. +RW double layer discs are not playable.
CD-DA
VCD (Video CD)
DivX/MPEG1/MPEG2
MP3/WMA/WAV
AAC/JPEG/MPEG4
Caution for DualDisc playback
The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the
use of Non-DVD side of a DualDisc on this product may not be recommended.
4 INTRODUCTIONS
CONTENTS
Detaching the control panel ........................... 3
Attaching the control panel ........................... 3
How to reset your unit ................................... 3
How to forcibly eject a disc ............................. 3
INTRODUCTIONS
Playable disc type .......................................... 4
OPERATIONS
Basic operations ............................................. 6
• Using the control panel .................................. 6
• Using the remote controller (RM-RK255) ....... 8
Preparation .................................................... 10
Listening to the radio ..................................... 11
Disc operations ............................................... 12
• Operations using the control panel ................ 14
SETTINGS
Selecting a preset sound mode ...................... 35
Menu operations ............................................ 37
Color settings ................................................. 40
Title assignment ............................................ 41
Disc setup menu ............................................. 42
Bluetooth settings ......................................... 44
REFERENCES
More about this unit ...................................... 45
Maintenance .................................................. 51
Troubleshooting ............................................. 52
Specifications ................................................. 58
• Operations using the remote controller
(RM-RK255) ................................................... 16
USB operations .............................................. 22
EXTERNAL DEVICES
Using the Bluetooth ® devices ........................ 23
• Using the Bluetooth cellular phone ............... 26
• Using the Bluetooth audio player .................. 27
Listening to the CD changer ........................... 28
Listening to the iPod/iPhone ......................... 29
• When connected with the USB cable ............. 29
• When connected with the interface
adapter .......................................................... 33
Listening to the other external
components ................................................ 34
5
Basic operations
Using the control panel
1 •
FM/AM
•
DISC
•
CD-CH
•
IPOD
Confirm selection.
•
BT-PHONE/BT-AUDIO
previous Bluetooth menu.
2 • Turn on the power.
• Attenuate the sound (if the power is on).
• Turn off the power [Hold].
3 • Select the source.
FM
USB (iPod)
(or
BT-AUDIO
(back to the beginning)
• Enter “DIAL” menu if a Bluetooth phone is
connected [Hold].
4 • Enter list operations.
• Enter Menu setting [Hold].
•
USB (iPod)
5 Select the display and button illumination color.
6 Loading slot
7 Display window
8 Eject disc.
9 Select the sound mode.
: Select preset station.
: Select title/program/playlist/folder.
: Select folder.
: Enter the main menu/Pause playback *2/
: Enter/go back to
=
AM
*3 =
DISC
*4 =
USB
*4/
4, *5
*
=
EXT INPUT
) =
*4 =
CD-CH
BT-PHONE
LINE IN
*4/
=
IPOD
*4 =
AV IN
: Enter the main menu.
*4
*3 =
p USB (Universal Serial Bus) input terminal
q Detach the panel.
w •
FM/AM
•
DISC/USB/USB (iPod)
•
CD-CH/IPOD
•
BT-PHONE/BT-AUDIO
: Search for station.
: Select chapter/track.
: Select track.
: Select setting item/
registered device.
e • Change the display information (if the power is
turned on).
• Check the current clock time (if the power is
turned off). *
r • Return to the previous menu.
•
USB (iPod)
6
: Switch the setting between
<HEAD MODE> and <IPOD MODE> *7 [Hold].
t • Control the volume *
2
or select items [Turn].
• Confirm the selection [Press].
• FM: Enter SSM preset mode [Hold].
•
DISC/USB/USB (iPod)
: Pause/resume
playback *2 [Press].
•
DISC/USB/USB (iPod)/CD-CH/IPOD
:
Enter playback mode [Hold].
•
BT-PHONE
y Remote sensor
u AV-IN (audio/video) input jack
: Adjust the volume [Turn].
*1 – *7 : See page 7.
6
*1 Also known as “Control dial” in this manual.
*2 You can still adjust the volume during pause when the selected source is “
DISC/USB/USB (iPod)/IPOD
.”
Before resume playback, check to be sure that you have not raise the volume level too much.
*3 You cannot select these sources if they were disabled in the Menu (see < SRC SELECT> in “Menu operations” on
page 39).
*4 You cannot select these sources if they are not ready or not connected.
5
When connecting the iPod/iPhone to the USB input jack for the first time, “
*
“
iPod
” appears on the top left corner of the display.
USB
” appears on the display first, then
*6 The current clock time is displayed if <CLOCK DISP> is set to <CLOCK OFF> (see page 37).
*7 You can use this function only when <IPOD MODE> is available for the connected iPod (see page 47).
Display window
1 Bluetooth indicator
2 Tr (track) indicator
3 Source display / Disc number / Track number /
Folder number / Title number / PBC indicator /
Time countdown indicator / Setting and list
operation information
4 USB indicator
5 iPod indicator
6 Playback mode / item indicators— RND (random),
(disc), (folder), RPT (repeat)
7 TAG (Tag information) indicator
8 ST (stereo) indicator
9 LOUD (loudness) indicator
p Menu hierarchy position indicator— (bottom),
(top), (middle)
q Status of Bluetooth device
(Device number, [ : 1 – 5]; signal strength,
[ : 0 – 3]*; battery reminder, [ : 0 – 3]*)
w Main display
e Disc/device information indicators— (track/
file), (folder)
* As the number increases, the signal/battery power
becomes stronger.
7OPERATIONS
Using the remote controller (RM-RK255)
Installing the batteries
R03/LR03/AAA
Insert the batteries into the remote controller by
matching the polarity (+ and –) correctly.
Caution:
• Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
• Battery shall not be exposed to excessive heat such as
sunshine, fire, or the like.
If the effectiveness of the remote controller
decreases, replace the batteries.
Before using the remote controller:
• Aim the remote controller directly at the remote
sensor on the unit.
• DO NOT expose the remote sensor to bright light
(direct sunlight or artificial lighting).
1 button
• Turns the power on if pressed briefly or
attenuates the sound when the power is on.
• Turns the power off if pressed and held.
2 5/∞ buttons
•
FM/AM
•
DISC
– DVD-Video: Selects the title.
– DVD-VR: Selects the program/playlist.
– DivX/MPEG Video/MP3/WMA/WAV: Selects
•
USB
– MPEG Video/MP3/WMA/WAV: Selects the
: Selects the preset stations.
:
the folders if included.
:
folders if included.
8
•
IPOD
:
– 5 : Enters the main menu (then 5 / ∞ /
4 / ¢ work as menu
selecting buttons.)
5 : Returns to the previous menu.
∞ : Confirms the selection.
–
•
∞ : Pauses or resumes playback.
BT-PHONE/BT-AUDIO
: Enter the Bluetooth
menu.
4 / ¢ buttons
•
FM/AM
:
– Searches for stations automatically if pressed
briefly.
– Searches for stations manually if pressed and
held.
DISC/USB/USB (iPod)/CD-CH
•
:
– Reverse skip/forward skip if pressed briefly.
– Reverse search/forward search if pressed and
held.
•
IPOD
:
– Reverse skip/forward skip if pressed briefly.
– Reverse search/forward search if pressed and
held.
In menu selecting mode:
– Selects an item if pressed briefly. (Then, press
∞ to confirm the selection.)
– Skips 10 items at a time if pressed and held.
•
BT-AUDIO
:
– Reverse skip/forward skip if pressed briefly.
3 VOL (volume) + / – buttons
• Adjusts the volume level.
2nd VOL (volume) buttons
• Not applicable for this unit.
4 * ASPECT button
• Not applicable for this unit.
5 PHONE button
• Answers incoming calls.
• Enters “DIAL” menu when a Bluetooth phone is
connected.
• Enters “REDIAL” menu when a Bluetooth phone
is connected [Hold].
6 * SETUP button
• Enters disc setup menu (during stop).
7 * TOP MENU button
• DVD-Video: Shows the disc menu.
• DVD-VR: Shows the Original Program screen.
• VCD: Resumes PBC playback.
USB (iPod)
•
8 * OSD (on-screen display) button
: Enters the search mode menu.
• Shows the on-screen bar.
9 SHIFT button
• Functions with other buttons.
p DISP (display) button
• Changes the display information (if the power is
turned on).
• Checks the current clock time (if the power is
turned off).
q 1 / ¡ buttons
• DVD-Video: Slow motion playback (during
pause).
• DVD-VR/VCD: Forward slow motion playback
(during pause).
• DivX/MPEG Video/MP3/WMA/WAV/
USB (iPod)
w SOURCE button
• Selects the source.
e 3 (play) / 8 (pause) button
•
DISC/USB/USB (iPod)/BT-AUDIO
: Reverse search/forward search.
USB/
: Starts/
pauses playback.
•
BT-PHONE
•
BT-AUDIO
r (end call) button
: Answers incoming calls.
: Starts playback.
• Ends the call.
7 (stop) buttons
•
DISC/USB/USB (iPod)/BT-AUDIO
: Stops
playback.
t * RETURN button
•
VCD
: Returns to the PBC menu.
•
USB (iPod)
: Returns to Control Screen.
Continued on the next page
9OPERATIONS
y *
DVD MENU button
• DVD-Video: Shows the disc menu.
• DVD-VR: Shows the Playlist screen.
• VCD: Resumes PBC playback.
•
USB (iPod)
u * % / fi buttons
• DVD-Video: Makes selection/settings.
•
CD-CH
@ / # buttons
• DVD-Video: Makes selection/settings.
• DivX/MPEG Video: Skips back or forward by
about five minutes.
: Enters the search mode menu.
: Changes discs in the magazine.
* DUAL button
i
• Not applicable for this unit.
o DIRECT button
•
DISC/USB
chapter/title/program/playlist/folder/track
when pressed with SHIFT button (see page 17 for
details).
CLR (clear) button
•
DISC/USB
with SHIFT button.
* Functions as number buttons/ * (asterisk)/# (hatch)
when pressed with SHIFT button.
–
DISC/USB
folder/track number after entering search mode by
pressing SHIFT and DIRECT (see page 17 for details).
: Enters direct search mode for
: Erases the misentry when pressed
: Enters chapter/title/program/playlist/
ENT (enter) button
• Confirms selection.
Preparation
Canceling the display demonstration and setting the clock
• See also page 37.
1
2
Press and hold until the
main menu is called up.
[Turn] = [Press]
• Repeat this procedure.
Turn on the power.
Cancel the display demonstrations
Select <DEMO>, then <DEMO OFF>.
Set the clock
Select <CLOCK> = <CLOCK SET>.
Adjust the hour, then press control dial once to proceed to
adjust the minute.
• To return to the previous menu, press BACK.
10
Listening to the radio
1
2
Changing the display information
Frequency = Clock = Station name * = (back to the
beginning)
* If no title is assigned to a station, “NO NAME” appears.
To assign a title to a station, see page 41.
Select “
Search for a station to listen—Auto Search.
When a station is tuned in, searching stops. To stop searching, press the same button
again.
• You can also search for a station manually—Manual Search. Hold either one of the
• When receiving an FM stereo broadcast with sufficient signal strength, the ST indicator
FM
” or “
AM
.”
buttons until “M” flashes on the display, then press it repeatedly.
lights up on the display.
Storing stations in memory
Automatic presetting (FM)— SSM (Strongstation Sequential Memory)
You can preset up to 18 stations for FM.
1 While listening to a station...
Improving the FM reception
When an FM stereo broadcast is hard to receive,
activate monaural mode for better reception.
• See also page 38.
[Turn] = [Press]
Reception improves, but stereo effect will be lost.
To restore the stereo effect, repeat the same
procedure to select <MONO OFF>.
2 Select the preset number range you want to
store.
3
Local FM stations with the strongest signals are
searched and stored automatically.
• To stop searching, press 4 /¢ .
To preset other 6 stations, repeat from step 1 again.
11OPERATIONS
Manual presetting (FM/AM)
You can preset up to 18 stations for FM and 6 stations
for AM.
Ex.: Storing FM station of 92.50 MHz into preset
number “04.”
1
2 Select preset number “04.”
3
Selecting preset station
or
[Turn] = [Press]
Disc operations
Before performing any operations...
Turn on the monitor to watch the playback picture. If you turn on the monitor, you can also control playback of other
discs by referring to the monitor screen. (See pages 18 – 21.)
The disc type is automatically detected, and playback starts automatically (for DVD: automatic start depends on its
internal program).
If the current disc does not have any disc menu, all tracks will be played repeatedly until you change the source or
eject the disc.
If “ ” appears on the monitor when pressing a button, the unit cannot accept the operation you have tried to
do.
• In some cases, without showing “
1
2
,” operations will not be accepted.
Turn on the power.
Insert a disc.
All tracks will be played repeatedly until you change the source
or eject the disc.
12
Stop playing and ejecting the disc
• “NO DISC” appears. Press SRC to listen to another
playback source.
Selecting a track/folder (MP3/WMA/WAV/CD)
Prohibiting disc ejection
To cancel the prohibition, repeat the same
procedure.
Changing the display information
Current chapter number and Elapsed playing time = Current chapter number and Clock =
Current title and chapter number = (back to the beginning)
Current chapter number and Elapsed playing time = Current chapter number and Clock =
Current program (or playlist) number and chapter number = (back to the beginning)
Elapsed playing time = Folder number and Clock = Folder name = Track title = (back
to the beginning)
[Turn] = [Press]
• For MP3/WMA/WAV discs, select the desired folder,
then the desired track by repeating the control dial
procedures.
• To return to the previous menu, press BACK.
Current track number and Elapsed playing time = Current track number and Clock =
(back to the beginning)
Current track number and Elapsed playing time = Current track number and Clock =
Album name/performer (folder name *1) = Track title (file name *1) = (back to the
beginning)
Current track number and Elapsed playing time = Current track number and Clock = Disc
title/performer *2 = Track title *2 = (back to the beginning)
1
*
If the file does not have Tag information or <TAG DISPLAY> is set to <TAG OFF> (see page 38), folder name and
file name appear. TAG indicator will not light up.
*2 “NO NAME” appears for an audio CD.
13OPERATIONS
Operations using the control panel
Pressing (or holding) the following buttons allows you to...
Disc type
[Press] Select chapter
[Hold] Reverse/fast-forward
chapter *
1
[Press] Select chapter
[Hold] Reverse/fast-forward
chapter *
1
[Press] Select track
[Hold] Reverse/fast-forward
2
track *
[Press] Select track
[Hold] Reverse/fast-forward
1
track *
[Press] Select track
[Hold] Reverse/fast-forward
1
track *
[Press] Select track
[Hold] Reverse/fast-forward
1
track *
Select title [Press] Pause/resume
playback
Select program number/
playlist number
[Press] Pause/resume
playback
Select folder [Press] Pause/resume
playback
[Press] Pause/resume
—
playback
Select folder [Press] Pause/resume
playback
[Press] Pause/resume
—
playback
1
*
Search speed:
*2 Search speed:
14
Selecting the playback modes
You can use only one of the following playback modes at a time.
1 23
= [Press] [Turn] = [Press]
[Turn]
REPEAT Ô RANDOM
Disc type REPEAT RANDOM
CHAPTER RPT: Repeat current chapter
TITLE RPT: Repeat current title
CHAPTER RPT: Repeat current chapter
PROGRAM RPT: Repeat current program
(not available for Playlist Playback)
TRACK RPT: Repeat current track
FOLDER RPT: Repeat current folder
TRACK RPT: Repeat current track (PBC not
in use)
TRACK RPT: Repeat current track
FOLDER RPT: Repeat current folder
TRACK RPT: Repeat current track ALL RND: Randomly play all tracks
FOLDER RND: Randomly play all tracks of
current folder, then tracks of next
folders
ALL RND: Randomly play all tracks
ALL RND: Randomly play all tracks (PBC not
in use)
FOLDER RND: Randomly play all tracks of
current folder, then tracks of next
folders
ALL RND: Randomly play all tracks
—
—
• To cancel repeat play or random play, select “RPT OFF” or “RND OFF.”
• To return to the previous menu, press BACK.
15OPERATIONS
Operations using the remote controller (RM-RK255)
Button
/
Stop play Stop play
Start play/Pause (if pressed during play) Start play/Pause (if pressed during play)
• Reverse/forward chapter search *1 (No sound
can be heard.)
Reverse/forward track search *4 (No sound can
be heard.)
• Slow motion *2 during pause (No sound can
be heard.)
– DVD-VR: Reverse slow motion does not work.
[Press] Select chapter (during play or pause)
[Hold] Reverse/fast-forward chapter search *
[Press] Select track
3
[Hold] Reverse/fast-forward track search *5 (No
sound can be heard.)
• DVD-Video: Select title (during play or pause)
Select folder
• DVD-VR: Select program
Select playlist (during play or pause)
*1 Search speed:
*2 Slow motion speed:
*3 Search speed:
*4 Search speed:
*5 Search speed:
—
• Skip back or forward the scenes by about
five minutes
• Select chapter
16
Button
Stop play Stop play Stop play
1
– *3: See page 16.
*
Start play/Pause (if pressed
during play)
Reverse/forward track search *
• Forward slow motion *2
during pause (No sound can
be heard.)
– Reverse slow motion does not
work.
[Press] Select track
[Hold] Reverse/fast-forward
track search *3 (No
sound can be heard.)
—
Start play/Pause (if pressed
during play)
1
Reverse/forward track search *1Reverse/forward track search *
[Press] Select track
[Hold] Reverse/fast-forward
track search *
3
Start play/Pause (if pressed
during play)
[Press] Select track
[Hold] Reverse/fast-forward
track search *
3
Select folder
—
1
Searching for chapter/title/program/playlist/folder/track directly (DVD/DivX/MPEG Video/
MP3/WMA/WAV/CD)
1 While holding SHIFT, press DIRECT repeatedly to select the desired search mode.
DVD-Video:
DVD-VR:
DivX/MPEG Video:
MP3/WMA/WAV:
CD:
2 While holding SHIFT, press the number buttons (0 – 9) to enter the desired number.
3 Press ENT (enter) to confirm.
Continued on the next page
17OPERATIONS
• For DivX/MPEG Video/MP3/WMA/WAV, track is
searched within the same folder.
• For DVD-VR, program/playlist search is possible
during Original program playback (PG)/Playlist
playback (PL).
• To erase a misentry, press CLR (clear) while holding
SHIFT.
• To return to the previous screen, press RETURN.
Operations using the on-screen bar
(DVD/DVD-VR/DivX/MPEG Video/VCD)
These operations are possible on the monitor using the
remote controller.
1 Show the on-screen bar (see page 19).
(twice)
Using menu driven features... (DVD-Video/
DVD-VR)
1 Press TOP MENU/DVD MENU to enter the menu
screen.
2 Press % / fi / @ / # to select an item you want to
start play.
3 Press ENT (enter) to confirm.
Canceling the PBC playback... (VCD)
1 During stop, press DIRECT while holding SHIFT.
2 Hold SHIFT, then press the number buttons (0 – 9)
to enter the desired number.
3 Press ENT (enter) to confirm.
• To resume PBC, press TOP MENU/DVD MENU.
2 Select an item.
3 Make a selection.
If pop-up menu appears...
• To cancel pop-up menu, press RETURN.
• For entering time/numbers, see the following.
Entering time/numbers
Press % / fi to change the number, then press @ / # to
move to the next entry.
• Each time you press % / fi, the number increases/
decreases by one value.
• After entering the numbers, press ENT (enter).
• It is not required to enter the zero and tailing zeros
(the last two digits in the example below).
18
Ex.: Time search
DVD: _:_ _:_ _ (Ex.: 1:02:00)
Press % once, then # twice to go to the third entry, %
twice, then press ENT (enter).
Removing the on-screen bar
On-screen bar
Ex.: DVD-Video
Information
Operation
1 Disc type
2 • DVD-Video: Audio signal format type and
channel
• VCD: PBC
3 Playback mode *
DVD-Video: T. RPT: Title repeat
C. RPT: Chapter repeat
DVD-VR: C. RPT: Chapter repeat
PG. RPT: Program repeat
DivX/MPEG Video: T. RPT: Track repeat
F. RPT: Folder repeat
A. RND: All random
F. RND: Folder random
VCD *2: T. RPT: Track repeat
A. RND: All random
4 Playback information
Current program/chapter
Current playlist/chapter
1
Current title/chapter
Current track
6 Playback status
Play
7 Operation icons
Forward/reverse search
Forward/reverse slow-motion
Pause
Stop
Change time indication (see 5)
Time Search (Enter the elapsed
Title Search (by its number)
Chapter Search (by its number)
Track Search (by its number)
Change the audio language or
Change or turn off the subtitle
Change the view angle
Repeat play *
Random play *
playing time of the current title/
program/playlist or of the disc.)
audio channel
language
1
1
5 Time indication
Current folder/track
Elapsed playing time of the disc
(For DVD-Video, elapsed playing
time of the current title/program/
playlist.)
DVD-Video/DVD-VR: Remaining
title/program/playlist time
VCD: Remaining disc time
Elapsed playing time of the current
chapter/track *
Remaining time of the current
chapter/track *
*1 For repeat play/random play, see also page 15.
*2 While PBC is not in use.
*3 Not applicable for DVD-VR.
3
3
19OPERATIONS
Operations using the control
screen
(DivX/MPEG Video/MP3/WMA/WAV/CD)
These operations are possible on the monitor using the
remote controller.
6 Current track number/total number of tracks in the
current folder (total number of tracks on the disc)
7 Track information
8 Track list with the current track selected
Selecting a playback mode
1 Show the control screen.
DivX/MPEG Video: Press
MP3/WMA/WAV/CD: Automatically appear during
play.
7 during play.
2 Select “Folder” column or “Track” column
(except for CD).
3 Select a folder or track.
4 Start playback.
DivX/MPEG Video: Press ENT (enter) or 3/8.
MP3/WMA/WAV/CD: Playback starts automatically.
Control screen
• See also page 15.
1 While control screen is displayed...
Playback mode selection screen appears on the
folder list section of the control screen.
2 Select a playback mode.
REPEAT Ô RANDOM
3 Select an item.
REPEAT
FOLDER *
REPEAT
REPEAT
TRACK
RANDOM
ALL
: Repeat current folder
: Repeat current track
: Randomly play all tracks
Ex.: MP3/WMA/WAV disc
1 Current folder number/total folder number
2 Folder list with the current folder selected
3 Selected playback mode
4 Elapsed playing time of the current track
5 Operation mode icon ( 3, 7, 8, ¡, 1 )
20
RANDOM
RANDOM
FOLDER *
• To cancel repeat play or random play, select
“REPEAT OFF” or “RANDOM OFF.”
* Not selectable for CD.
4 Confirm the selection.
: Randomly play all tracks of
current folder, then tracks
of next folders
Loading...