JVC KD-DV5304, KD-DV4304, KD-DV4303, KD-DV5303, KD-DV5306 Installation & Connection Manual
...
1
KD-DV5304/KD-DV5303/
KD-DV4304/KD-DV4303
Installation/Connection Manual
GET0440-002A
[UI]
1206DTSMDTJEIN
EN
© 2006 Victor Company of Japan, Limited
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
WARNINGS
• DO NOT install any unit in locations where;
– it may obstruct the steering wheel and gearshift lever operations.
– it may obstruct the operation of safety devices such as air bags.
– it may obstruct visibility.
• DO NOT operate the unit while driving.
• If you need to operate the unit while driving, be sure to look ahead carefully.
• The driver must not watch the monitor while driving.
If the parking brake is not engaged, “DRIVER MUST NOT WATCH THE MONITOR WHILE DRIVING.” appears on the monitor, and no playback picture will be shown.
– This warning appears only when the parking brake wire is connected to the parking brake system built in the car.
To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit.
• Be sure to ground this unit to the car’s chassis again after installation.
Notes:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer.
• It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W, change
“AMP GAIN” setting to prevent the speakers from being damaged (see page 24 of the INSTRUCTIONS).
• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.
• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.
Heat sink
PRECAUTIONS on power supply and speaker connections:
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car.
Parts list for installation and connection
If any item is missing, consult your JVC car audio dealer immediately.
A / B
Hard case/Control panel
F
Crimp connector
J
Rubber cushion
G
Washer (ø5)
K
Handles
C
Sleeve
D
Trim plate
H
Lock nut (M5)
L
Remote controller
I
Mounting bolt (M5
M
Battery
E
Power cord
× 20 mm)
2
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Do the required electrical connections.
Bend the appropriate tabs to hold the
sleeve firmly in place.
When using the optional stay
Fire wall
Dashboard
Install the unit at an angle of less than 30˚.
Removing the unit
Before removing the unit, release the rear section.
Stay (option)
Screw (option)
When installing the unit without using the sleeve
In a Toyota car for example, first remove the car radio and install the unit in its place.
2
Flat type screws (M5 × 8 mm)
2
Bracket *
Pocket
Note : When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer screws
are used, they could damage the unit.
*
2
Bracket *
Flat type screws (M5 × 8 mm) *
2
1
*
When you stand the unit, be careful not to damage the fuse on the rear.
2
*
Not supplied for this unit.
TROUBLESHOOTING
• The fuse blows.
* Are the red and black leads connected correctly?
• Power cannot be turned on.
* Is the yellow lead connected?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• Noise interfere with sounds.
* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?
• This unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• This unit does not work at all.
* Have you reset your unit?
Insert the two handles, then pull them as
illustrated so that the unit can be removed.
3
ELECTRICAL CONNECTIONS
A
Typical connections
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.
The leads of the power cord and those of the connector from the car body may be different in color.
1 Connect the colored leads of the power cord in the order specified in the illustration below.
2 Connect the antenna cord.
3 Finally connect the wiring harness to the unit.
LINE IN
VIDEO OUT
(see diagram
)
For KD-DV5304/KD-DV5303 (see diagram )
Antenna terminal
DIGITAL OUT
(see diagram
Line out (see diagram
Rear ground terminal
)
)
To external components (see diagram )
15 A fuse
Black
2
*
Yellow
Red
Blue
Blue with white stripe
Light green
To metallic body or chassis of the car
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
To an accessory terminal in the fuse block
To the automatic antenna if any (250 mA max.)
To the remote lead of other equipment (200 mA max.)
To parking brake, metallic body or chassis of the car
Ignition switch
Fuse block
Left speaker (front) Right speaker (front) Left speaker (rear) Right speaker (rear)
Connecting the parking brake wire
B
When installing the monitor in a location where it can be seen by the driver
Connect the parking brake wire to the parking brake system built in the car.
Parking brake
Parking brake switch (inside the car)
When installing the monitor in a location where it cannot be seen by the driver
Connect the parking brake wire to metallic body or chassis of the car.
PurplePurple with black stripeGreenGreen with black stripeGrayGray with black stripeWhiteWhite with black stripe
Parking brake wire (light green)
To metallic body or chassis of the car
C
Connecting the crimp connector
Wire connecting the battery and the parking brake switch.
Attach the parking brake wire to this point.
1
*
Not supplied for this unit.
2
*
Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power cannot be turned on.
Parking brake wire (light green)
Contact the metallic part of the crimp to the wires inside.
Pinch the crimp firmly.
4
D
Required connections for DVD playback
3
KV-MR9010
9-INCH WIDESCREEN MONITOR *
Connecting the external amplifier
E
Video cord *
Audio/video control amplifier or the decoder compatible with the
multichannel digital sources
3
You can connect an amplifier to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit.
• Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker leads of this unit unused.
Remote lead Y-connector *
Remote lead (blue with white stripe)
Rear speakers
Digital optical cable *
To the remote lead of other equipment or automatic antenna if any
3
3
JVC Amplifier
Front speakers
F
Connecting the external components
JVC CD changer, Apple iPod, or JVC D. player
• Set “CHANGER” for the external input setting (See page 24 of the INSTRUCTIONS.)
You can connect these components as illustrated below. The iPod or D. player can be connected using an interface adapter (not supplied)—KS-PD100 (for iPod) or KS-PD500 (for D. player).
CAUTION
:
Before connecting the external components, make sure that the unit is turned off.
CD changer jack
iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.
JVC CD changer
or
Apple iPod
or
JVC D. player
Other external component
• Set “EXT IN” for the external input setting (See page 24 of the INSTRUCTIONS.)
External component
CD changer jack
3.5 mm stereo mini plug
or
3
*
Not supplied for this unit.
4
*
Signal cord (not supplied for this unit).
5
*
Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint (if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.
6
*
Connecting cord supplied for your CD changer.
7
*
Line Input Adapter KS-U57 (not supplied for this unit).
8
*
AUX Input Adapter KS-U58 (not supplied for this unit).
External component
Only for KD-DV5304/KD-DV5303
External component
Loading...