Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)
Power RequirementOperating VoltageDC 14.4 V (11 V to 16 V allowance)
Grounding SystemNegative ground
Allowable Operating Temperature0°C to +40°C (32°F to 104°F)
Dimensions (W × H × D)Installation Size (approx.)182 mm × 52 mm × 158 mm (7-3/16" × 2-1/16" × 6-1/4")
Panel Size (approx.)187 mm × 58 mm × 13 mm (7-3/8" × 2-5/16" × 9/16")
Mass (approx.)1.6 kg (3.6 lbs) (excluding accessories)
Power RequirementOperating VoltageDC 14.4 V (11 V to 16 V allowance)
Grounding SystemNegative ground
Allowable Operating Temperature0°C to +40°C
Dimensions (W × H × D)Installation Size (approx.)182 mm × 52 mm × 158 mm
Panel Size (approx.)188 mm × 58 mm × 11 mm
Mass (approx.)1.6 kg (excluding accessories)
MPEG-2: 24 kHz, 22.05 kHz, 16 kHz
GENERAL
Design and specifications are subject to change without notice.
1-8 (No.MA308)
1.1Safety Precautions
SECTION 1
PRECAUTION
!
!
Burrs formed during molding may be left over on some parts of the chassis. Therefore,
pay attention to such burrs in the case of preforming repair of this system.
Please use enough caution not to see the beam directly or touch it in case of an
adjustment or operation check.
(No.MA308)1-9
1.2Preventing static electricity
Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser
diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
1.2.1 Grounding to prevent damage by static electricity
Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products.
Be careful to use proper grounding in the area where repairs are being performed.
(1) Ground the workbench
Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the
traverse unit (optical pickup) on it.
(2) Ground yourself
Use an anti-static wrist strap to release any static electricity built up in your body.
(caption)
Anti-static wrist strap
1M
Conductive material
(conductive sheet) or iron plate
(3) Handling the optical pickup
• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical
pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)
• Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily
destroy the laser diode.
1.3Handling the traverse unit (optical pickup)
(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.
(2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the
replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a
time when attaching it to the connector.
(3) Handle the flexible cable carefully as it may break when subjected to strong force.
(4) It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.
1.4Attention when traverse unit is decomposed
*Please refer to "Disassembly method" in the text for the pickup unit.
• Apply solder to the short land before the card wire is disconnected from the connector on the pickup unit.
(If the card wire is disconnected without applying solder, the pickup may be destroyed by static electricity.)
• In the assembly, be sure to remove solder from the short land after connecting the card wire.
[except KD-DVH426][for KD-DVH426]
Flexible wire
Flexible wire
1-10 (No.MA308)
CN101
Short-circuit points
Mechanism control board
CN101
Short-circuit points
Mechanism control board
1.5Important for laser products
1.CLASS 1 LASER PRODUCT
2.CAUTION :
(For U.S.A.) Visible and/or invisible class II laser radiation
when open. Do not stare into beam.
(Others) Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
3.CAUTION : Visible and/or invisible laser radiation when
open and inter lock failed or defeated. Avoid direct
exposure to beam.
4.CAUTION : This laser product uses visible and/or invisible
laser radiation and is equipped with safety switches which
prevent emission of radiation when the drawer is open and
the safety interlocks have failed or are defeated. It is
dangerous to defeat the safety switches.
5.CAUTION : If safety switches malfunction, the laser is able
to function.
6.CAUTION : Use of controls, adjustments or performance of
procedures other than those specified here in may result in
hazardous radiation exposure.
!
Please use enough caution not to
see the beam directly or touch it
in case of an adjustment or operation
check.
REPRODUCTION AND POSITION OF LABELS and PRINT
WARNING LABEL and PRINT
(No.MA308)1-11
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.
1-12 (No.MA308)
3.1Main body
3.1.1 Removing the Bottom chassis
(See Fig.1)
(1) Disengage the five hooks a engaged bottom chassis.
SECTION 3
DISASSEMBLY
3.1.2 Removing the Heat sink
(See Fig.2)
(1) Remove the two screws A and three screws B attaching
the Heat sink.
a
a
a
a
a
Fig.1
A
3.1.3 Removing the Front chassis assembly
(See Fig.3)
(1) From the both side of Front chassis, remove the two
screws C attaching the Front chassis.
(2) Disengage the both side of four hooks b engaged Front
chassis.
B
Fig.2
b
C
b
Fig.3
(No.MA308)1-13
3.1.4 Removing the Main board assembly
(See Fig.4 and 5)
(1) Remove the three screws D attaching the Main board as-
sembly. (See Fig.4)
(2) Remove the three screws E attaching Rear bracket. (See
Fig.5)
(3) Disconnect the connector CN961
anism assembly. (See Fig.4)
connected to DVD mech-
CN961
D
D
Fig.4
E
Fig.5
1-14 (No.MA308)
3.1.5 Removing the DVD mechanism assembly
(See Fig.6 and 7)
(1) Remove the three screws F attaching the DVD mechanism
assembly. (See Fig.6)
(2) Remove the two screws G attaching the DVD bracket. (See
Fig.7)
F
F
Fig.6
3.1.6 Removing the Switch board assembly
(See Fig.8)
(1) Remove the Volume knob from Front panel assembly.
(2) Remove the five screws H attaching the Back cover.
(3) Disengage the fourteen hooks c engaged Back cover.
G
G
Fig.7
HH
cccc
cc
HHH
cc
Fig.8
(No.MA308)1-15
3.2DVD mechanism assembly (except KD-DVH426)
3.2.1 Removing the mechanism control board
(See Fig.1)
Caution:
Before disconnecting the flexible wire extending from the DVD
pickup, solder the short-circuit point on the flexible wire using
a grounding soldering iron. If you do not follow this instruction,
the DVD pickup may be damaged.
(1) Turn over the body, and solder the short-circuit points on
the flexible wire extending from the DVD pickup.
(2) Disconnect the flexible wire from connector CN101
mechanism control board.
(3) Disconnect the card wire from connector CN201
mechanism control board.
(4) Disconnect the flexible wire from connector CN202
mechanism control board.
(5) Unsolder two soldered points a on the mechanism control
board and remove the wire extending from the feed motor.
(6) Remove the screw A attaching the lug wire.
(7) Remove the two screws B and screw C attaching the
mechanism control board.
Caution:
• As the flexible wire to be connected to CN101
attach it to the mechanism control board using a double
tape.
• After reassembling, unsolder the short-circuit points.
on the
on the
on the
, make sure to
Flexible wire
Double tape
CN101
B
Short-circuit points
A
Lug wire
B
CN201
Feed motor
a
C
CN202
Mechanism control board
Fig.1
1-16 (No.MA308)
3.2.2 Removing the top cover
(See Fig.2)
(1) Remove the two screws D attaching the top cover on the
back of the body.
(2) Remove the top cover upward.
Reference:
When reassembling, set part b of the top cover under the
bending part c of the chassis frame.
3.2.3 Removing the mechanism section
(See Fig.2 to 4)
• Remove the top cover.
(1) From the bottom of the body, remove the screw E attaching
the lug wire. (See Fig.2.)
(2) Remove the two screws F attaching the right and left stop-
pers on the front side. (See Fig.2.)
(3) Remove the two floating springs on the bottom of the body.
(See Fig.3.)
(4) Move the mechanism section upward and remove from the
chassis frame.
The three damper springs come off from the dampers.
(See Fig.4.)
Caution:
• When reassembling, reattach the damper spring to the
damper respectively and insert the three shafts on the bottom of the mechanism to the dampers.
• Before inserting the shaft to the dampers, apply IPA to the
hole of damper.
Floating spring
Fig.3
Mechanism section
Stopper
F
Top cover
Stopper
F
D
D
b
c
E
Lug wire
Damper SP.(F)
(Silver)
Damper (F)
(Black)
Damper SP.(F)
(Silver)
Damper (F)
(Black)
Fig.4
Damper SP.(R)
(Red)
Damper (R)
(Purple)
Chassis frame
Fig.2
(No.MA308)1-17
3.2.4 Removing the clamper unit
(See Fig.5 to 7)
• Remove the top cover and the mechanism section.
(1) Remove the clamper2 spring on the bottom of the mecha-
nism section. (See Figs.5.and 6.)
(2) Release the part d of the clamper spring from the bending
part of the chassis base assembly. (See Fig.7.)
(3) Move the clamper unit in the direction of the arrow and turn.
Release the two joints e and f, then remove the clamper
unit upward. (See Fig.6.)
3.2.5 Reattaching the clamper unit
(See Fig.5 to 9)
(1) Attach the clamper spring to the clamper unit. (See Fig.8.)
(2) Move the clamper unit to set the side joints e and f to each
boss of the chassis base assembly. Make sure that part g
is inserted to the notch of the chassis base assembly. (See
Figs.5 and 9.)
(3) Move the part d of the clamper spring to the outside of the
bending part of the chassis base assembly. (See Fig.7.)
(4) Attach the clamper2 spring to the chassis base assembly.
(See Figs.5 and 6.)
Caution:
When reattaching, temporarily hook the end of the clamper
spring as shown in the figure to make the work easy. (See
Fig.8.)
Clamper unit
Clamper2 spring
Chassis base assembly
Fig.6
Clamper spring
Clamper spring
f
Clamper2 spring
Chassis base assembly
g
d
Chassis base assembly
Fig.7
e
Fig.5
1-18 (No.MA308)
Clamper unit
Clamper unit
Clamper spring
Fig.8
Fig.9
g
Notch
(No.MA308)1-19
3.2.6 Removing the front unit
(See Fig.10 to 12)
• Remove the top cover and the mechanism section.
(1) Disconnect the flexible wire from connector CN202 on the
mechanism control board at the bottom of the body. (See
Fig.10.)
(2) Remove the screw G attaching the front unit on the top of
the body. (See Fig.11.)
(3) Move the front unit toward the front to release joint h, and
release two joints i and j on the right side of the chassis
base assembly. Then remove the front unit upward. (See
Figs.11 and 12.)
(4) Remove the two screws H attaching the switch board. (See
Fig.12.)
Reference:
You can remove the switch board only without removing the
front unit.
Caution:
When reassembling, attach the flexible wire extending from
the switch board using the double tape. (See Figs.10 and 12.)
Mechanism control board
G
Front unit
h
Fig.11
CN202
Double tape
Fig.10
Flexible wire
Double tape
j
i
H
Switch board
Front unit
G
1-20 (No.MA308)
h
Fig.12
3.2.7 Removing the loading arm assembly
(See Fig.13 , 14)
• Remove the top cover, the mechanism section and the front
unit.
(1) From the top of the body, move the loading arm assembly
from the front side upward, and release the bosses from
the right and left joints k and m of the chassis base assembly.
(2) Release the boss from notch n of the connect arm on the
right side of the body, and release the boss from notch p of
the slide cam assembly on the left side.
m
Loading arm assembly
Side cam
assembly
p
m
k
Fig.13
Loading arm assembly
k
n
n
Connect arm
Fig.14
(No.MA308)1-21
3.2.8 Removing the rod (L)(R)/roller assembly
(See Fig.15 and 16)
• Remove the top cover, the mechanism section, the front unit
and the loading arm assembly.
(1) Release the rod (L) and (R) from the joints q at the bottom
of the loading arm assembly (See Fig.15.)
(2) Remove the roller assembly from the loading arm assem-
bly. (See Fig.16.)
(3) Remove the two collars and washer from the roller assem-
bly. (See Fig.16.)
Caution:
After attaching the loading arm assembly to the roller assembly, attach the rod (L) and (R). Attach the rods to the right and
left collars of the roller. (See Fig.15.)
When reattaching the rod (L) and (R) to the loading arm assembly, engage each joint as shown in Fig.15. As joints q of
the rod (L), let the rod through q before reattaching it.
Collar
Collar
Rod(R)Rod(L)
q
q
q
Collar
Rod(L)
Rod(R)
q
Loading arm assembly
Fig.15
Roller assembly
Loading arm assembly
q
Rod(L)
q
Collar
Washer
Rod(R)
1-22 (No.MA308)
Fig.16
3.2.9 Removing the DVD pickup assembly
(See Fig.17 to 19)
• Remove the mechanism control board.
(1) From the bottom of the body, turn the feed gear in the di-
rection of the arrow to move the DVD pickup outwards.
(See Fig.17.)
(2) Remove the screw J attaching the thrust spring. (See
Fig.17.)
(3) Remove the DVD pickup assembly upward on the L.S.gear
side and release from sub shaft at joint r. Move the lead
screw of the DVD pickup assembly in the direction of the
arrow to release from joint s. (See Fig.18.)
Caution:
• When releasing the lead screw at joint s, the L.S.collar
comes off at the end of the lead screw. When reassembling, reattach the L.S.collar to the lead screw and
engage joint s. (See Fig.18.)
• When reattaching the L.S.collar, reattach it to the point
s of the lead screw, and to the rod (M). Make sure that
the L.S.collar is set on the rod (M) spring. (See Fig.18.)
(4) Remove the screw K attaching the rack spring/ rack plate
on the DVD pickup. (See Fig.19.)
(5) Pull out the lead screw. (See Fig.19.)
Caution:
Perform adjustment after replacing the pickup.
DVD Pickup assembly
DVD Pickup assembly
Feed gear
J
Thrust spring
Fig.17
s
L.S.collar
Rod(M)
Lead screw
Sub shaft
L.S.collar
r
L.S.gear
Fig.18
K
Rack spring
Lead screw
Rack plate
DVD Pickup
Fig.19
(No.MA308)1-23
3.2.10 Removing the spindle motor
r
(See Fig.20)
• Remove the mechanism control board.
Remove the two screws L attaching the spindle motor on the
bottom of the body.
Caution:
Perform adjustment when reattaching the spindle motor.
3.2.11 Removing the feed motor assembly
(See Fig.21 and 22)
• Remove the mechanism control board.
(1) Remove the feed TRI. spring on the bottom of the body.
(See Fig.21.)
(2) Remove the two screws M attaching the feed motor as-
sembly. (See Fig.21.)
(3) Remove the slit washer from the motor H. assembly and
pull out the worm wheel. (See Fig.22.)
Remove the two screws N attaching the feed motor. (See
Fig.22.)
Spindle motor
Feed TRI. spring
L
Fig.20
M
Feed motor assembly
1-24 (No.MA308)
Fig.21
Slit washer
Worm wheel
Feed moto
N
Motor H. assembly
Fig.22
3.3DVD mechanism assembly (for KD-DVH426)
3.3.1 Removing the mechanism control board
(See Fig.1)
Caution:
Before disconnecting the flexible wire extending from the DVD
pickup, solder the short-circuit point on the flexible wire using
a grounding soldering iron. If you do not follow this instruction,
the DVD pickup may be damaged.
(1) Turn over the body, and solder the short-circuit points on
the flexible wire extending from the DVD pickup.
(2) Disconnect the flexible wire from connector CN101
mechanism control board.
(3) Disconnect the card wire from connector CN201
mechanism control board.
(4) Disconnect the flexible wire from connector CN202
mechanism control board.
(5) Unsolder two soldered points a on the mechanism control
board and remove the wire extending from the feed motor.
(6) Remove the screw A attaching the lug wire.
(7) Remove the two screws B and screw C attaching the
mechanism control board.
Caution:
• As the flexible wire to be connected to CN101
attach it to the mechanism control board using a double
tape.
• After reassembling, unsolder the short-circuit points.
on the
on the
on the
, make sure to
Flexible wire
Double tape
CN101
B
Short-circuit points
A
Lug wire
B
CN201
Feed motor
a
C
CN202
Mechanism control board
Fig.1
(No.MA308)1-25
3.3.2 Removing the top cover
(See Fig.2)
(1) Remove the two screws D attaching the top cover on the
back of the body.
(2) Remove the top cover upward.
Reference:
When reassembling, set part b of the top cover under the
bending part c of the chassis frame.
3.3.3 Removing the mechanism section
(See Fig.2 to 4)
• Remove the top cover.
(1) From the bottom of the body, remove the screw E attaching
the lug wire. (See Fig.2.)
(2) Remove the two screws F attaching the right and left stop-
pers on the front side. (See Fig.2.)
(3) Remove the two floating springs on the bottom of the body.
(See Fig.3.)
(4) Move the mechanism section upward and remove from the
chassis frame.
The three damper springs come off from the dampers.
(See Fig.4.)
Caution:
• When reassembling, reattach the damper spring to the
damper respectively and insert the three shafts on the bottom of the mechanism to the dampers.
• Before inserting the shaft to the dampers, apply IPA to the
hole of damper.
Floating spring
Fig.3
Mechanism section
Stopper
F
Top cover
Stopper
F
D
D
b
c
E
Lug wire
Damper SP.(F)
(Silver)
Damper (F)
(Black)
Damper SP.(F)
(Silver)
Damper (F)
(Black)
Fig.4
Damper SP.(R)
(Red)
Damper (R)
(Purple)
Chassis frame
1-26 (No.MA308)
Fig.2
3.3.4 Removing the clamper unit
(See Fig.5 to 7)
• Remove the top cover and the mechanism section.
(1) Remove the clamper2 spring on the bottom of the mecha-
nism section. (See Figs.5.and 6.)
(2) Release the part d of the clamper spring from the bending
part of the chassis base assembly. (See Fig.7.)
(3) Move the clamper unit in the direction of the arrow and turn.
Release the two joints e and f, then remove the clamper
unit upward. (See Fig.6.)
3.3.5 Reattaching the clamper unit
(See Fig.5 to 9)
(1) Attach the clamper spring to the clamper unit. (See Fig.8.)
(2) Move the clamper unit to set the side joints e and f to each
boss of the chassis base assembly. Make sure that part g
is inserted to the notch of the chassis base assembly. (See
Figs.5 and 9.)
(3) Move the part d of the clamper spring to the outside of the
bending part of the chassis base assembly. (See Fig.7.)
(4) Attach the clamper2 spring to the chassis base assembly.
(See Figs.5 and 6.)
Caution:
When reattaching, temporarily hook the end of the clamper
spring as shown in the figure to make the work easy. (See
Fig.8.)
Clamper unit
Clamper2 spring
Chassis base assembly
Fig.6
Clamper spring
Clamper spring
f
Clamper2 spring
Chassis base assembly
g
d
Chassis base assembly
Fig.7
e
Fig.5
(No.MA308)1-27
Clamper unit
Clamper unit
Clamper spring
Fig.8
1-28 (No.MA308)
Fig.9
g
Notch
3.3.6 Removing the front unit
(See Fig.10 to 12)
• Remove the top cover and the mechanism section.
(1) Disconnect the flexible wire from connector CN202
mechanism control board at the bottom of the body. (See
Fig.10.)
(2) Remove the screw G attaching the front unit on the top of
the body. (See Fig.11.)
(3) Move the front unit toward the front to release joint h, and
release two joints i and j on the right side of the chassis
base assembly. Then remove the front unit upward. (See
Figs.11 and 12.)
(4) Remove the two screws H attaching the switch board. (See
Fig.12.)
Reference:
You can remove the switch board only without removing the
front unit.
Caution:
When reassembling, attach the flexible wire extending from
the switch board using the double tape. (See Figs.10 and 12.)
Mechanism control board
on the
G
Front unit
h
Fig.11
CN202
Double tape
Fig.10
Flexible wire
Double tape
j
i
H
Switch board
Front unit
G
Fig.12
h
(No.MA308)1-29
3.3.7 Removing the loading arm assembly
(See Fig.13 , 14)
• Remove the top cover, the mechanism section and the front
unit.
(1) From the top of the body, move the loading arm assembly
from the front side upward, and release the bosses from
the right and left joints k and m of the chassis base assembly.
(2) Release the boss from notch n of the connect arm on the
right side of the body, and release the boss from notch p of
the slide cam assembly on the left side.
m
Loading arm assembly
Side cam
assembly
p
m
k
Fig.13
Loading arm assembly
k
n
n
Connect arm
1-30 (No.MA308)
Fig.14
3.3.8 Removing the rod (L)(R)/roller assembly
(See Fig.15 and 16)
• Remove the top cover, the mechanism section, the front unit
and the loading arm assembly.
(1) Release the rod (L) and (R) from the joints q at the bottom
of the loading arm assembly (See Fig.15.)
(2) Remove the roller assembly from the loading arm assem-
bly. (See Fig.16.)
(3) Remove the two collars and washer from the roller assem-
bly. (See Fig.16.)
Caution:
After attaching the loading arm assembly to the roller assembly, attach the rod (L) and (R). Attach the rods to the right and
left collars of the roller. (See Fig.15.)
When reattaching the rod (L) and (R) to the loading arm assembly, engage each joint as shown in Fig.15. As joints q of
the rod (L), let the rod through q before reattaching it.
Collar
Collar
Rod(R)Rod(L)
q
q
q
Collar
Rod(L)
Rod(R)
q
Loading arm assembly
Fig.15
Roller assembly
Loading arm assembly
q
Rod(L)
q
Collar
Washer
Rod(R)
Fig.16
(No.MA308)1-31
3.3.9 Removing the DVD pickup assembly
(See Fig.17 to 19)
• Remove the mechanism control board.
(1) From the bottom of the body, turn the feed gear in the di-
rection of the arrow to move the DVD pickup outwards.
(See Fig.17.)
(2) Remove the screw J attaching the thrust spring. (See
Fig.17.)
(3) Remove the DVD pickup assembly upward on the L.S.gear
side and release from sub shaft at joint r. Move the lead
screw of the DVD pickup assembly in the direction of the
arrow to release from joint s. (See Fig.18.)
Caution:
• When releasing the lead screw at joint s, the L.S.collar
comes off at the end of the lead screw. When reassembling, reattach the L.S.collar to the lead screw and
engage joint s. (See Fig.18.)
• When reattaching the L.S.collar, reattach it to the point
s of the lead screw, and to the rod (M). Make sure that
the L.S.collar is set on the rod (M) spring. (See Fig.18.)
(4) Remove the screw K attaching the rack spring/ rack plate
on the DVD pickup. (See Fig.19.)
(5) Pull out the lead screw. (See Fig.19.)
Caution:
Perform adjustment after replacing the pickup.
DVD Pickup assembly
DVD Pickup assembly
Feed gear
J
Thrust spring
Fig.17
s
L.S.collar
Rod(M)
Lead screw
Sub shaft
L.S.collar
r
L.S.gear
Fig.18
K
Rack spring
Lead screw
Rack plate
DVD Pickup
Fig.19
1-32 (No.MA308)
3.3.10 Removing the spindle motor
r
(See Fig.20)
• Remove the mechanism control board.
Remove the two screws L attaching the spindle motor on the
bottom of the body.
Caution:
Perform adjustment when reattaching the spindle motor.
3.3.11 Removing the feed motor assembly
(See Fig.21 and 22)
• Remove the mechanism control board.
(1) Remove the feed TRI. spring on the bottom of the body.
(See Fig.21.)
(2) Remove the two screws M attaching the feed motor as-
sembly. (See Fig.21.)
(3) Remove the slit washer from the motor H. assembly and
pull out the worm wheel. (See Fig.22.)
Remove the two screws N attaching the feed motor. (See
Fig.22.)
Spindle motor
Feed TRI. spring
L
Fig.20
M
Feed motor assembly
Fig.21
Slit washer
Worm wheel
Feed moto
N
Motor H. assembly
Fig.22
(No.MA308)1-33
SECTION 4
ADJUSTMENT
4.1Test instruments required for adjustment
(1) Digital oscilloscope (100MHz)
(2) Jitter meter
(3) Digital tester
(4) Electric voltmeter
(5) Tracking offset meter
(6) Test Disc : VT501 or VT502
(7) Extension studs : STDV001-3P
(8) Extension cable : EXTDV002-30P
4.3Connection method
Connection procedure
(1) Attach the front chassis assembly to the main board.
(2) Connect the front panel assembly to the main board.
(3) Attach the heat sink and rear bracket to the main board.
(4) Attach the extension studs to the DVD mechanism assembly.
(5) Connect the DVD mechanism assembly and the main board with a extension cable.
4.2Standard measuring conditions
Power supply voltage : DC14.4V(11V to 16V)
Load impedance : 4Ω(2 Speakers connection)
Line output : 20kΩ
Caution:
Be sure to attach the heat sink and rear bracket onto the power
amplifier IC and regulator IC respectively, before supply the
power.
If voltage is applied without attaching these parts, the power
amplifier IC and regulator IC will be destroyed by heat.
Extension cable
EXTDV002-30P
Heat sink
Rear bracket
Main board
Extension stud
STDV001-3P
Extension studs
STDV001-3P
1-34 (No.MA308)
4.4Adjustment method for jitter
After replacing the pickup, set the unit in the service mode to display a jitter value on the LCD.
Confirm that the jitter value measured with a jitter meter is within 12% of the jitter value displayed on the LCD.
If it is within 12%, then adjustment is not necessary.
If the measured jitter value is outside the 12% tolerance range, perform the following adjustments.
4.4.1 Adjustment procedure
(1) Set the unit to the service mode and display a jitter value (hex data) on the LCD.
(2) Turn each of the screws a, b and c, by a half-turn per step, in the direction that reduces the jitter value in order to minimize it.
(Do not turn a screw more than a half turn at a time, but adjust the screws in the cycle of the same level is turned in the pair of
b+c and the same level is turned in the pair of a+b.)
(3) After completing the adjustment, secure the screws with screw lock paint.
c
b
a
Jitter value adjustment procedure (Pickup horizontal level adjustment relative to the DVD recording surface)
(For the adjustment tool use a 3 mm wrench and not a screwdriver, this procedure will make the adjustment easier.)
3 mm wrench
(1) Set the unit to the service mode and display a jitter value (hex data) on the LCD.
(2) Turn each of the screws a, b and c, by a half-turn per step, in the direction that reduces the jitter value in order to minimize it.
(Do not turn a screw more than a half turn at a time, but adjust the screw in the cycle of same level turn by pair of b+c → pair of
a+b.)
(3) After completing the adjustment, secure the screws with screw lock paint.
(No.MA308)1-35
4.5Jitter value conversion table
Load the test DVD and set the unit to the service mode. A jitter value converted to the hex value is displayed on the LCD.
Refer to the corresponding decimal notation value shown in the following Jitter Conversion Table.
The adjustment is OK if the jitter value measured with a jitter meter is within 12% of the jitter value displayed on the LCD.
If the measured jitter value is outside the 12% tolerance range, adjust it to minimize the difference between the measured value and
the displayed value.
Keep this state more than 2 seconds while
continuing pressing the [SEL] button, [SOURCE]
button and [STANDBY/ON ATTENUATOR]
button sequentially.
The unit enters the service mode.
"INIT ALL" isInitialize all data to the factory setting
indicated on the LCD.
"VERSION" is Microcomputer version display
indicated on the LCD.
"AREA/RGN" is Destination area/region display
indicated on the LCD.
"VIDEO" is Setting of NTSC or PAL
indicated on the LCD.
"CLR ERR" is Clear loading/ejection error history
indicated on the LCD.
Press the [SEL] key
:The system control EEPROM is
initialized entirely.
Press the [SEL] key
S-XXX-YY System control CPU
version/ROM correction version
DVD-XXXXDVD version
*Exchanging it operate each indication with the
[DISC UP] button and [DISC DOWN] button.
Press the [SEL] key
STS-X XX System control destination
DVD-X XX DVD unit destination
DVDRGN X DVD unit region
*Exchanging it operate each indication with the
[DISC UP] button and [DISC DOWN] button.
Press the [SEL] key
"NTSC" or "PAL" are indicated on the LCD.
*Exchanging it operate each indication with the
[DISC UP] button and [DISC DOWN] button.
Note:
There is the model that is not equipped with
this mode by a version.
Press the [SEL] key
:The error history stored in the EEPROM is
cleared.
"CD ERROR" isRead loading and ejection error history
indicated on the LCD.
Error code (1 byte)
First byte[01] Eject error
AB
Press the [SEL] key
[02] Loading error
: The error history saved in the system control
is read and displayed.
TOT-xxxx : Total error count.
Total error count
(A figure between 0 and 9999 is
displayed. 10000 or more is also
Enyyzzzz: Latest three error code.
0nyyzzzz: First five error code
*Exchanging it operate each indication with the
[DISC UP] button and [DISC DOWN] button.
displayed as 9999.)
Detailed error code
Error code
Counter
Detailed error code
Error code
Counter
(No.MA308)1-37
AB
"DVD-TEMP" is
indicated on the LCD.
Detailed error code (2 bytes)
First byteHigher 4 bits Route NO. (Process of error occurrence)
Lower 4 bits Error type
. . . .
Refer to charts 1.1 and 1.2.
. . . .
*Displayed with loading/ejection error only.
[1] Time out
[2] Switch status error
[3] Swinging error
Second bytebit7
(Example) When a switch status error occurs during loading route 3 and
the switch status is L/L/H/H/H (00111B = 07H), the error code
. . . .
Disc type (0: 12 cm. 1: 8 cm)
bit6,5
bit4
bit3
bit2
bit1 SW 1 status
bit0 RESET SW status
Victor company of Japan, Limited
Mobile Entertainment Business Group Mobile Entertainment Category 10-1,1chome,Ohwatari-machi,Maebashi-city,Gumma-ken, 371-8543,Japan
(No.MA308)
Printed in Japan
VPT
PARTS LIST
KD-ADV5380J,KD-DV5300J,KD-DV5301E
KD-DV5301EU,KD-DV5302E,KD-DV5302EU
KD-DV5304UI,KD-DV5305U,KD-DV5305UN
KD-DV5305UT,KD-DV5305A,KD-DV5306U
KD-DV5306UN,KD-DV5306UT,KD-DV5306A
KD-DV5307EE,KD-DV5308EE,KD-DV5388UF
KD-DV4304UI,KD-DV4305U,KD-DV4305UN
KD-DV4305UT,KD-DV4305A,KD-DV4306U
KD-DV4306UN,KD-DV4306UT,KD-DV4306A
KD-DV4388UF,KD-DVH426UN
* All printed circuit boards and its assemblies are not available as service parts.
MA308
- Contents -
Exploded view of general assembly and parts list (Block No.M1)
Exploded view of general assembly and parts list (Block No.M2)
DVD mechanism assembly and parts list (Block No.MJ)
DVD mechanism assembly and parts list (Block No.MU)
Electrical parts list (Block No.01~12)
Packing materials and accessories parts list (Block No.M3)
D11SS355W-XDIODE
D1o r MA 111 - XSI DI O DE
D21SS355W-XDIODE
D2o r MA 111 - XSI DI O DE
D301UDZW11B-XZ DIODE
D301or MA8110/M/-XZ DIODE
D3021SS355W-XDIODE
D302or MA111-XSI DIODE
D303or CRS03-WSB DIODE
D303MA22D23-XSB DIODE
D303or RB160M-30-XSB DIODE
D304or CRS03-WSB DIODE
D304MA22D23-XSB DIODE
D304or RB160M-30-XSB DIODE
D3441SS355W-XDIODE
D344or MA111-XSI DIODE
C1NCBA1AK-104WC CAPACITOR0.1uF 10V K
C2QEKJ1AM-107ZE CAPACITOR100uF 10V M
C4NCBA1AK-104WC CAPACITOR0.1uF 10V K
C5NCBA1AK-104WC CAPACITOR0.1uF 10V K
C6QEKJ1AM-107ZE CAPACITOR100uF 10V M
C7NCBA1AK-104WC CAPACITOR0.1uF 10V K
C81QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C91QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C103QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C109NCBA1AK-104WC CAPACITOR0.1uF 10V K
C113QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C151QTE1C57-106ZE CAPACITOR10uF 16V
C152NCBA1CK-103WC CAPACITOR0.01uF 16V K
C161QTE1A57-107ZE CAPACITOR100uF 10V
C162NCBA1CK-103WC CAPACITOR0.01uF 16V K
C164QTE1C57-106ZE CAPACITOR10uF 16V
C171QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C172QTE1H54-225ZE CAPACITOR2.2uF 50V
C173QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
Part No.Part NameDescriptionLocal
ADV5
380J
ADV5
380J
3-15
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
Part No.Part NameDescriptionLocal
C174QEKJ1CM-226ZE CAPACITOR22uF 16V M
C175NCBA1EK-472WC CAPACITOR4700pF 25V K
C176NCBA1AK-104WC CAPACITOR0.1uF 10V K
C177QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C178QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C179NDCA1HJ-471WC CAPACITOR470pF 50V J
C180NCFA1AZ-474WC CAPACITOR0.47uF 10V Z
C181QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C182QTE1H54-225ZE CAPACITOR2.2uF 50V
C183QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C184QEKJ1CM-226ZE CAPACITOR22uF 16V M
C185NCBA1EK-472WC CAPACITOR4700pF 25V K
C186NCBA1AK-104WC CAPACITOR0.1uF 10V K
C187QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C188QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C189NDCA1HJ-471WC CAPACITOR470pF 50V J
C190NCFA1AZ-474WC CAPACITOR0.47uF 10V Z
C301QEKJ1CM-476ZE CAPACITOR47uF 16V M
C302NCBA1CK-103WC CAPACITOR0.01uF 16V K
C304QERF1HM-475ZE CAPACITOR4.7uF 50V M
C305QTE1C57-476ZE CAPACITOR47uF 16V
C306NCBA1CK-103WC CAPACITOR0.01uF 16V K
C307NCBA1CK-103WC CAPACITOR0.01uF 16V K
C309QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C328QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C329NDCA1HJ-101WC CAPACITOR100pF 50V J
C331NCBA1CK-223WC CAPACITOR0.022uF 16V K
C338QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C339NDCA1HJ-101WC CAPACITOR100pF 50V J
C346QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C348QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C349NDCA1HJ-101WC CAPACITOR100pF 50V J
C356QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C358QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C359NDCA1HJ-101WC CAPACITOR100pF 50V J
C401NDCA1HJ-220WC CAPACITOR22pF 50V J
C402NCBA1CK-103WC CAPACITOR0.01uF 16V K
C403NCBA1CK-103WC CAPACITOR0.01uF 16V K
C404QEKJ0JM-107ZE CAPACITOR100uF 6.3V M
C405NDCA1HJ-220WC CAPACITOR22pF 50V J
C406NCBA1CK-103WC CAPACITOR0.01uF 16V K
C411QEKJ1AM-227ZE CAPACITOR220uF 10V M
C412NCBA1AK-473WC CAPACITOR0.047uF 10V K
C413QCZ0202-155ZC CAPACITOR1.5uF 25V Z
C414QERF0JM-337ZE CAPACITOR330uF 6.3V M
C701NCBA1AK-104WC CAPACITOR0.1uF 10V K
C702NCBA1AK-104WC CAPACITOR0.1uF 10V K
C703NCBA1AK-104WC CAPACITOR0.1uF 10V K
C704QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C705QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C706QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C731QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C732NCBA1CK-103WC CAPACITOR0.01uF 16V K
C743NDCA1HJ-270WC CAPACITOR27pF 50V J
C744NDCA1HJ-220WC CAPACITOR22pF 50V J
C751NCFA1AZ-474WC CAPACITOR0.47uF 10V Z
C752NDCA1HJ-471WC CAPACITOR470pF 50V J
C753QEKJ1AM-227ZE CAPACITOR220uF 10V M
C754QEKJ1AM-227ZE CAPACITOR220uF 10V M
C755QEKJ1AM-227ZE CAPACITOR220uF 10V M
C756NCBA1AK-473WC CAPACITOR0.047uF 10V K
C757NDCA1HJ-471WC CAPACITOR470pF 50V J
C761NDCA1HJ-471WC CAPACITOR470pF 50V J
C801NDCA1HJ-220WC CAPACITOR22pF 50V J
C802NDCA1HJ-220WC CAPACITOR22pF 50V J
C803NCBA1AK-473WC CAPACITOR0.047uF 10V K
C804NDCA1HJ-220WC CAPACITOR22pF 50V J
C805QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C806QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C821QEKJ1CM-106ZE CAPACITOR10uF 16V M
C822QEKJ1CM-106ZE CAPACITOR10uF 16V M
C823NCBA1CK-103WC CAPACITOR0.01uF 16V K
C831NDCA1HJ-101WC CAPACITOR100pF 50V J
C861QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C862QEKJ1CM-107ZE CAPACITOR100uF 16V M
C885QEKJ1CM-106ZE CAPACITOR10uF 16V M
C901QEZ0768-278E CAPACITOR2700uF
ADV5
380J
C902NCBA1AK-104WC CAPACITOR0.1uF 10V K
C903QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C913QEKJ1CM-106ZE CAPACITOR10uF 16V M
C914NCBA1AK-104WC CAPACITOR0.1uF 10V K
C915QEKJ1AM-107ZE CAPACITOR100uF 10V M
C916NCBA1AK-104WC CAPACITOR0.1uF 10V K
C917NCBA1CK-103WC CAPACITOR0.01uF 16V K
C919NCBA1AK-473WC CAPACITOR0.047uF 10V K
C920QEKJ1CM-226ZE CAPACITOR22uF 16V M
C921QEKJ1AM-227ZE CAPACITOR220uF 10V M
C922QEKJ1AM-107ZE CAPACITOR100uF 10V M
C923QEKJ1AM-227ZE CAPACITOR220uF 10V M
C924NBZ0009-127XE. CAPACITOR120uF
C925QEZ0595-477ZE CAPACITOR470uF 25V M
C926NCBA1AK-104WC CAPACITOR0.1uF 10V K
C961NCBA1AK-473WC CAPACITOR0.047uF 10V K
C963NCBA1AK-104WC CAPACITOR0.1uF 10V K
C964NCBA1AK-104WC CAPACITOR0.1uF 10V K
C971QEKJ1CM-107ZE CAPACITOR100uF 16V M
C972NCBA1AK-473WC CAPACITOR0.047uF 10V K
C973QEKJ1AM-227ZE CAPACITOR220uF 10V M
C974NDCA1HJ-102WC CAPACITOR1000pF 50V J
C975QEKJ1AM-227ZE CAPACITOR220uF 10V M
C981NCBA1AK-104WC CAPACITOR0.1uF 10V K
L1QQL244J-4R7ZP COIL4.7uH J
L401NQR0007-002XFERRITE BEADS
L411NQL114K-470XINDUCTOR47uH K
L752QQL244J-470ZCOIL47uH J
L901QQR1378-002COIL
L911NQL56CK-220XCOIL22uH K
L921NQL56CK-220XCOIL22uH K
L922NQLB7GM-100XCOIL10uH M
L923NQL71EM-330XCOIL33uH M
C620NCB31HK-473XC CAPACITOR0.047uF 50V K
C661NCB21AK-105XC CAPACITOR1uF 10V K
C662NCS31HJ-681XC CAPACITOR680pF 50V J
C663NCB31HK-223XC CAPACITOR0.022uF 50V K
C682NCB31HK-103XC CAPACITOR0.01uF 50V K
D11SS355W-XDIODE
D1o r MA 111 - XSI DI O DE
D21SS355W-XDIODE
D2o r MA 111 - XSI DI O DE
D301UDZW11B-XZ DIODE
D301or MA8110/M/-XZ DIODE
D3021SS355W-XDIODE
D302or MA111-XSI DIODE
D303or CRS03-WSB DIODE
D303MA22D23-XSB DIODE
D303or RB160M-30-XSB DIODE
D304or CRS03-WSB DIODE
DV53
01E,D
V5301
EU,D
V5302
E,DV5
302E
U
DV53
01E,D
V5301
EU,D
V5302
E,DV5
302E
U
DV53
01E,D
V5301
EU,D
V5302
E,DV5
302E
U
DV53
01E,D
V5301
EU,D
V5302
E,DV5
302E
U
C1NCBA1AK-104WC CAPACITOR0.1uF 10V K
C2QEKJ1AM-107ZE CAPACITOR100uF 10V M
C4NCBA1AK-104WC CAPACITOR0.1uF 10V K
C5NCBA1AK-104WC CAPACITOR0.1uF 10V K
C6QEKJ1AM-107ZE CAPACITOR100uF 10V M
C7NCBA1AK-104WC CAPACITOR0.1uF 10V K
C71QEKJ1CM-106ZE CAPACITOR10uF 16V M
C72NDCA1HJ-331WC CAPACITOR330pF 50V J
C73NCBA1CK-103WC CAPACITOR0.01uF 16V K
C74NCBA1HK-561WC CAPACITOR560pF 50V K
C75QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C76NCBA1CK-103WC CAPACITOR0.01uF 16V K
C77NDCA1HJ-330WC CAPACITOR33pF 50V J
DV53
01E,D
V5301
EU,D
V5302
E,DV5
302E
U
DV53
01E,D
V5301
EU,D
V5302
E,DV5
302E
U
3-19
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
Part No.Part NameDescriptionLocal
C78NDCA1HJ-330WC CAPACITOR33pF 50V J
C81QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C91QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C103QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C109NCBA1AK-104WC CAPACITOR0.1uF 10V K
C113QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C141NCBA1EK-472WC CAPACITOR4700pF 25V K
C142NCBA1EK-472WC CAPACITOR4700pF 25V K
C143NCFA1AZ-474WC CAPACITOR0.47uF 10V Z
C145QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C146QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C147QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C151QTE1C57-106ZE CAPACITOR10uF 16V
DV53
01E,D
V5301
EU,D
V5302
E,DV5
302E
U
DV53
01E,D
V5301
EU,D
V5302
E,DV5
302E
U
DV53
01E,D
V5301
EU,D
V5302
E,DV5
302E
U
DV53
01E,D
V5301
EU,D
V5302
E,DV5
302E
U
DV53
01E,D
V5301
EU,D
V5302
E,DV5
302E
U
DV53
01E,D
V5301
EU,D
V5302
E,DV5
302E
U
DV53
01E,D
V5301
EU,D
V5302
E,DV5
302E
U
DV53
01E,D
V5301
EU,D
V5302
E,DV5
302E
U
DV53
01E,D
V5301
EU,D
V5302
E,DV5
302E
U
DV53
01E,D
V5301
EU,D
V5302
E,DV5
302E
U
C152NCBA1CK-103WC CAPACITOR0.01uF 16V K
C161QTE1A57-107ZE CAPACITOR100uF 10V
C162NCBA1CK-103WC CAPACITOR0.01uF 16V K
C164QTE1C57-106ZE CAPACITOR10uF 16V
C171QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C172QTE1H55-225ZE CAPACITOR2.2uF 50V
C173QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C174QEKJ1CM-226ZE CAPACITOR22uF 16V M
C175NCBA1EK-472WC CAPACITOR4700pF 25V K
C176NCBA1AK-104WC CAPACITOR0.1uF 10V K
C177QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C178QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C179NDCA1HJ-471WC CAPACITOR470pF 50V J
C180NCFA1AZ-474WC CAPACITOR0.47uF 10V Z
C181QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C182QTE1H55-225ZE CAPACITOR2.2uF 50V
C183QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C184QEKJ1CM-226ZE CAPACITOR22uF 16V M
C185NCBA1EK-472WC CAPACITOR4700pF 25V K
C186NCBA1AK-104WC CAPACITOR0.1uF 10V K
C187QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C188QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C189NDCA1HJ-471WC CAPACITOR470pF 50V J
C190NCFA1AZ-474WC CAPACITOR0.47uF 10V Z
C301QEKJ1CM-476ZE CAPACITOR47uF 16V M
C302NCBA1CK-103WC CAPACITOR0.01uF 16V K
C304QERF1HM-475ZE CAPACITOR4.7uF 50V M
C305QTE1C57-476ZE CAPACITOR47uF 16V
C306NCBA1CK-103WC CAPACITOR0.01uF 16V K
C307NCBA1CK-103WC CAPACITOR0.01uF 16V K
C309QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C328QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C329NDCA1HJ-101WC CAPACITOR100pF 50V J
C331NCBA1CK-223WC CAPACITOR0.022uF 16V K
C338QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C339NDCA1HJ-101WC CAPACITOR100pF 50V J
C346QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C348QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C349NDCA1HJ-101WC CAPACITOR100pF 50V J
C356QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C358QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C359NDCA1HJ-101WC CAPACITOR100pF 50V J
C401NDCA1HJ-220WC CAPACITOR22pF 50V J
C402NCBA1CK-103WC CAPACITOR0.01uF 16V K
C403NCBA1CK-103WC CAPACITOR0.01uF 16V K
C404QEKJ0JM-107ZE CAPACITOR100uF 6.3V M
C405NDCA1HJ-220WC CAPACITOR22pF 50V J
C406NCBA1CK-103WC CAPACITOR0.01uF 16V K
C411QEKJ1AM-227ZE CAPACITOR220uF 10V M
C412NCBA1AK-473WC CAPACITOR0.047uF 10V K
C413QCZ0202-155ZC CAPACITOR1.5uF 25V Z
C414QERF0JM-337ZE CAPACITOR330uF 6.3V M
C701NCBA1AK-104WC CAPACITOR0.1uF 10V K
C702NCBA1AK-104WC CAPACITOR0.1uF 10V K
C721NDCA1HJ-471WC CAPACITOR470pF 50V J
C731QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C732NCBA1CK-103WC CAPACITOR0.01uF 16V K
C743NDCA1HJ-270WC CAPACITOR27pF 50V J
C744NDCA1HJ-220WC CAPACITOR22pF 50V J
C751NCFA1AZ-474WC CAPACITOR0.47uF 10V Z
C752NDCA1HJ-471WC CAPACITOR470pF 50V J
C753QEKJ1AM-227ZE CAPACITOR220uF 10V M
C754QEKJ1AM-227ZE CAPACITOR220uF 10V M
C755QEKJ1AM-227ZE CAPACITOR220uF 10V M
C756NCBA1AK-473WC CAPACITOR0.047uF 10V K
C757NDCA1HJ-471WC CAPACITOR470pF 50V J
C761NDCA1HJ-471WC CAPACITOR470pF 50V J
C801NDCA1HJ-220WC CAPACITOR22pF 50V J
C802NDCA1HJ-220WC CAPACITOR22pF 50V J
C803NCBA1AK-473WC CAPACITOR0.047uF 10V K
C804NDCA1HJ-220WC CAPACITOR22pF 50V J
C805QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
DV53
01E,D
V5301
EU,D
V5302
E,DV5
302E
U
3-20
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
Part No.Part NameDescriptionLocal
C806QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C821QEKJ1CM-106ZE CAPACITOR10uF 16V M
C822QEKJ1CM-106ZE CAPACITOR10uF 16V M
C823NCBA1CK-103WC CAPACITOR0.01uF 16V K
C831NDCA1HJ-101WC CAPACITOR100pF 50V J
C861QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C862QEKJ1CM-107ZE CAPACITOR100uF 16V M
C885QEKJ1CM-106ZE CAPACITOR10uF 16V M
C892NCBA1AK-104WC CAPACITOR0.1uF 10V K
C901QEZ0843-278E CAPACITOR2700uF
C902NCBA1AK-104WC CAPACITOR0.1uF 10V K
C903QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C913QEKJ1CM-106ZE CAPACITOR10uF 16V M
C914NCBA1AK-104WC CAPACITOR0.1uF 10V K
C915QEKJ1AM-107ZE CAPACITOR100uF 10V M
C916NCBA1AK-104WC CAPACITOR0.1uF 10V K
C917NCBA1CK-103WC CAPACITOR0.01uF 16V K
C919NCBA1AK-473WC CAPACITOR0.047uF 10V K
C920QEKJ1CM-226ZE CAPACITOR22uF 16V M
C921QEKJ1AM-227ZE CAPACITOR220uF 10V M
C922QEKJ1AM-107ZE CAPACITOR100uF 10V M
C923QEKJ1AM-227ZE CAPACITOR220uF 10V M
C924NBZ0009-127XE. CAPACITOR120uF
C925QEZ0595-477ZE CAPACITOR470uF 25V M
C926NCBA1AK-104WC CAPACITOR0.1uF 10V K
C961NCBA1AK-473WC CAPACITOR0.047uF 10V K
C963NCBA1AK-104WC CAPACITOR0.1uF 10V K
C964NCBA1AK-104WC CAPACITOR0.1uF 10V K
C971QEKJ1CM-107ZE CAPACITOR100uF 16V M
C972NCBA1AK-473WC CAPACITOR0.047uF 10V K
C973QEKJ1AM-227ZE CAPACITOR220uF 10V M
C974NDCA1HJ-102WC CAPACITOR1000pF 50V J
C975QEKJ1AM-227ZE CAPACITOR220uF 10V M
C981NCBA1AK-104WC CAPACITOR0.1uF 10V K
L752QQL244J-470ZCOIL47uH J
L901QQR1378-002COIL
L911NQL56CK-220XCOIL22uH K
L921NQL56CK-220XCOIL22uH K
L922NQLB7GM-100XCOIL10uH M
L923NQL71EM-330XCOIL33uH M
C1NCBA1AK-104WC CAPACITOR0.1uF 10V K
C2QEKJ1AM-107ZE CAPACITOR100uF 10V M
C4NCBA1AK-104WC CAPACITOR0.1uF 10V K
C5NCBA1AK-104WC CAPACITOR0.1uF 10V K
C6QEKJ1AM-107ZE CAPACITOR100uF 10V M
C7NCBA1AK-104WC CAPACITOR0.1uF 10V K
C81QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C91QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C161QTE1A57-107ZE CAPACITOR100uF 10V
C162NCBA1CK-103WC CAPACITOR0.01uF 16V K
C164QTE1C57-106ZE CAPACITOR10uF 16V
C171QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C172QTE1H54-225ZE CAPACITOR2.2uF 50V
C173QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C174QEKJ1CM-226ZE CAPACITOR22uF 16V M
C175NCBA1EK-472WC CAPACITOR4700pF 25V K
C176NCBA1AK-104WC CAPACITOR0.1uF 10V K
C177QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C178QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C179NDCA1HJ-471WC CAPACITOR470pF 50V J
C180NCFA1AZ-474WC CAPACITOR0.47uF 10V Z
C181QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C182QTE1H54-225ZE CAPACITOR2.2uF 50V
C183QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C184QEKJ1CM-226ZE CAPACITOR22uF 16V M
C185NCBA1EK-472WC CAPACITOR4700pF 25V K
C186NCBA1AK-104WC CAPACITOR0.1uF 10V K
C187QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C188QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
L1QQL244J-4R7ZP COIL4.7uH J
L401NQR0007-002XFERRITE BEADS
L411NQL114K-470XINDUCTOR47uH K
L752QQL244J-470ZCOIL47uH J
L901QQR1378-002COIL
L911NQL56CK-220XCOIL22uH K
L921NQL56CK-220XCOIL22uH K
L922NQLB7GM-100XCOIL10uH M
L923NQL71EM-330XCOIL33uH M
CN141QGA2006C1-04CONNECTOR W-B (1-4)
CN701QGZ1601J1-15CONNECTOR (1-15)
CN821QGA2001C1-02CONNECTOR W-B (1-2)
CN901QNZ0607-001CAR CONNECTOR
CN961QGB2044M1-30CONNECTOR B-B (1-30)
CN962QGF0534F3-45XCONNECTOR FFC/FPC (1-45)
CN963QGB2043L1-30XCONNECTOR B-B (1-30)
J1QNB0190-001CAR ANT JACK
J331QNN0770-0013P PIN JACK
J801QNZ0095-001CONNECTOR
K401NQR0007-002XFERRITE BEADS
K402NQR0007-002XFERRITE BEADS
K411NQR0201-004XFERRITE BEADS
C1NCBA1AK-104WC CAPACITOR0.1uF 10V K
C2QEKJ1AM-107ZE CAPACITOR100uF 10V M
C4NCBA1AK-104WC CAPACITOR0.1uF 10V K
C5NCBA1AK-104WC CAPACITOR0.1uF 10V K
C6QEKJ1AM-107ZE CAPACITOR100uF 10V M
C7NCBA1AK-104WC CAPACITOR0.1uF 10V K
C81QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C91QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C103QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C109NCBA1AK-104WC CAPACITOR0.1uF 10V K
C113QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C121NCBA1AK-104WC CAPACITOR0.1uF 10V K
C141NCBA1EK-472WC CAPACITOR4700pF 25V K
C142NCBA1EK-472WC CAPACITOR4700pF 25V K
C143NCFA1AZ-474WC CAPACITOR0.47uF 10V Z
C145QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C146QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C147QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C151QTE1C57-106ZE CAPACITOR10uF 16V
C152NCBA1CK-103WC CAPACITOR0.01uF 16V K
C161QTE1A57-107ZE CAPACITOR100uF 10V
C162NCBA1CK-103WC CAPACITOR0.01uF 16V K
C164QTE1C57-106ZE CAPACITOR10uF 16V
C171QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C172QTE1H54-225ZE CAPACITOR2.2uF 50V
DV53
88UF
DV53
88UF
DV53
88UF
DV53
88UF
DV53
88UF
DV53
88UF
DV53
88UF
DV53
88UF
DV53
88UF
DV53
88UF
DV53
88UF
DV53
88UF
3-35
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
Part No.Part NameDescriptionLocal
C173QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C174QEKJ1CM-226ZE CAPACITOR22uF 16V M
C175NCBA1EK-472WC CAPACITOR4700pF 25V K
C176NCBA1AK-104WC CAPACITOR0.1uF 10V K
C177QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C178QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C179NDCA1HJ-471WC CAPACITOR470pF 50V J
C180NCFA1AZ-474WC CAPACITOR0.47uF 10V Z
C181QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C182QTE1H54-225ZE CAPACITOR2.2uF 50V
C183QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C184QEKJ1CM-226ZE CAPACITOR22uF 16V M
C185NCBA1EK-472WC CAPACITOR4700pF 25V K
C186NCBA1AK-104WC CAPACITOR0.1uF 10V K
C187QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C188QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C189NDCA1HJ-471WC CAPACITOR470pF 50V J
C190NCFA1AZ-474WC CAPACITOR0.47uF 10V Z
C301QEKJ1CM-476ZE CAPACITOR47uF 16V M
C302NCBA1CK-103WC CAPACITOR0.01uF 16V K
C304QERF1HM-475ZE CAPACITOR4.7uF 50V M
C305QTE1C57-476ZE CAPACITOR47uF 16V
C306NCBA1CK-103WC CAPACITOR0.01uF 16V K
C307NCBA1CK-103WC CAPACITOR0.01uF 16V K
C309QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C328QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C329NDCA1HJ-101WC CAPACITOR100pF 50V J
C331NCBA1CK-223WC CAPACITOR0.022uF 16V K
C338QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C339NDCA1HJ-101WC CAPACITOR100pF 50V J
C346QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C348QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C349NDCA1HJ-101WC CAPACITOR100pF 50V J
C356QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C358QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C359NDCA1HJ-101WC CAPACITOR100pF 50V J
C401NDCA1HJ-220WC CAPACITOR22pF 50V J
C402NCBA1CK-103WC CAPACITOR0.01uF 16V K
C403NCBA1CK-103WC CAPACITOR0.01uF 16V K
C404QEKJ0JM-107ZE CAPACITOR100uF 6.3V M
C405NDCA1HJ-220WC CAPACITOR22pF 50V J
C406NCBA1CK-103WC CAPACITOR0.01uF 16V K
C411QEKJ1AM-227ZE CAPACITOR220uF 10V M
C412NCBA1AK-473WC CAPACITOR0.047uF 10V K
C413QCZ0202-155ZC CAPACITOR1.5uF 25V Z
C414QERF0JM-337ZE CAPACITOR330uF 6.3V M
C701NCBA1AK-104WC CAPACITOR0.1uF 10V K
C702NCBA1AK-104WC CAPACITOR0.1uF 10V K
C703NCBA1AK-104WC CAPACITOR0.1uF 10V K
C704QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C705QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C706QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C731QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C732NCBA1CK-103WC CAPACITOR0.01uF 16V K
C743NDCA1HJ-270WC CAPACITOR27pF 50V J
C744NDCA1HJ-220WC CAPACITOR22pF 50V J
C751NCFA1AZ-474WC CAPACITOR0.47uF 10V Z
C752NDCA1HJ-471WC CAPACITOR470pF 50V J
C753QEKJ1AM-227ZE CAPACITOR220uF 10V M
C754QEKJ1AM-227ZE CAPACITOR220uF 10V M
C755QEKJ1AM-227ZE CAPACITOR220uF 10V M
C756NCBA1AK-473WC CAPACITOR0.047uF 10V K
C757NDCA1HJ-471WC CAPACITOR470pF 50V J
C761NDCA1HJ-471WC CAPACITOR470pF 50V J
C801NDCA1HJ-220WC CAPACITOR22pF 50V J
C802NDCA1HJ-220WC CAPACITOR22pF 50V J
C803NCBA1AK-473WC CAPACITOR0.047uF 10V K
C804NDCA1HJ-220WC CAPACITOR22pF 50V J
C805QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C806QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C821QEKJ1CM-106ZE CAPACITOR10uF 16V M
C822QEKJ1CM-106ZE CAPACITOR10uF 16V M
C823NCBA1CK-103WC CAPACITOR0.01uF 16V K
C851NCBA1AK-104WC CAPACITOR0.1uF 10V K
C861QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
DV53
88UF
DV53
88UF
DV53
88UF
DV53
88UF
C862QEKJ1CM-107ZE CAPACITOR100uF 16V M
C885QEKJ1CM-106ZE CAPACITOR10uF 16V M
C901QEZ0768-278E CAPACITOR2700uF
C902NCBA1AK-104WC CAPACITOR0.1uF 10V K
C903QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C913QEKJ1CM-106ZE CAPACITOR10uF 16V M
C914NCBA1AK-104WC CAPACITOR0.1uF 10V K
C915QEKJ1AM-107ZE CAPACITOR100uF 10V M
C916NCBA1AK-104WC CAPACITOR0.1uF 10V K
C917NCBA1CK-103WC CAPACITOR0.01uF 16V K
C919NCBA1AK-473WC CAPACITOR0.047uF 10V K
C920QEKJ1CM-226ZE CAPACITOR22uF 16V M
C921QEKJ1AM-227ZE CAPACITOR220uF 10V M
C922QEKJ1AM-107ZE CAPACITOR100uF 10V M
C923QEKJ1AM-227ZE CAPACITOR220uF 10V M
C924NBZ0009-127XE. CAPACITOR120uF
C925QEZ0595-477ZE CAPACITOR470uF 25V M
C926NCBA1AK-104WC CAPACITOR0.1uF 10V K
C961NCBA1AK-473WC CAPACITOR0.047uF 10V K
C963NCBA1AK-104WC CAPACITOR0.1uF 10V K
C964NCBA1AK-104WC CAPACITOR0.1uF 10V K
C971QEKJ1CM-107ZE CAPACITOR100uF 16V M
C972NCBA1AK-473WC CAPACITOR0.047uF 10V K
C973QEKJ1AM-227ZE CAPACITOR220uF 10V M
C974NDCA1HJ-102WC CAPACITOR1000pF 50V J
C975QEKJ1AM-227ZE CAPACITOR220uF 10V M
C981NCBA1AK-104WC CAPACITOR0.1uF 10V K
L1QQL244J-4R7ZP COIL4.7uH J
L401NQR0007-002XFERRITE BEADS
L411NQL114K-470XINDUCTOR47uH K
L752QQL244J-470ZCOIL47uH J
L901QQR1378-002COIL
L911NQL56CK-220XCOIL22uH K
L921NQL56CK-220XCOIL22uH K
L922NQLB7GM-100XCOIL10uH M
L923NQL71EM-330XCOIL33uH M
CN141QGA2006C1-04CONNECTOR W-B (1-4)
CN701QGZ1601J1-15CONNECTOR (1-15)
Ω
1/4W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
1/16W J
Ω
DV53
88UF
DV53
88UF
3-37
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
Part No.Part NameDescriptionLocal
CN821QGA2001C1-02CONNECTOR W-B (1-2)
CN901QNZ0607-001CAR CONNECTOR
CN961QGB2044M1-30CONNECTOR B-B (1-30)
CN962QGF0534F3-45XCONNECTOR FFC/FPC (1-45)
CN963QGB2043L1-30XCONNECTOR B-B (1-30)
J1QNB0190-001CAR ANT JACK
J331QNN0770-0013P PIN JACK
J801QNZ0095-001CONNECTOR
K401NQR0007-002XFERRITE BEADS
K402NQR0007-002XFERRITE BEADS
K411NQR0201-004XFERRITE BEADS
L1NQL334J-4R7XCOIL4.7uH J
L2NQL093K-R22XCOIL0.22uH K
L401NQR0007-002XFERRITE BEADS
L411NQL114K-470XINDUCTOR47uH K
L721NQL38DK-330XCOIL33uH K
L722QQL244J-470ZCOIL47uH J
L901QQR1378-002COIL
L902NQL56CK-220XCOIL22uH K
L924NQL56CK-220XCOIL22uH K
L925NQL71EM-330XCOIL33uH M
L927NQLB7GM-100XCOIL10uH M
CN701QGZ1601J1-15CONNECTOR (1-15)
CN821QGA2001C1-02CONNECTOR W-B (1-2)
CN901QNZ0607-001CAR CONNECTOR
CN961QGB2027M3-30SCONNECTOR B-B (1-30)
CN962QGF0534F3-45XCONNECTOR FFC/FPC (1-45)
CN963QGB2027L9-30XCONNECTOR B-B (1-30)
J1QNB0190-001CAR ANT JACK
C661NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C662NCS31HJ-681XC CAPACITOR680pF 50V J
C663NCB31CK-223XC CAPACITOR0.022uF 16V K
C664NCB31CK-104XC CAPACITOR0.1uF 16V K
C681NBE20JM-475XTA E CAPACITOR4.7uF 6.3V M
C682NCB31HK-123XC CAPACITOR0.012uF 50V K
C686NCB31CK-223XC CAPACITOR0.022uF 16V K
C687NCB31CK-223XC CAPACITOR0.022uF 16V K
Q1022SC4617/R/-XTRANSISTOR
Q1032SB1424/R/-WTRANSISTOR
Q1042SC4617/R/-XTRANSISTOR
Q1052SC4617/R/-XTRANSISTOR
Q1062SK3019-XMOS FET
Q1072SK3019-XMOS FET
Q231RT1N141U-XTRANSISTOR
Q301RT1N441U-XTRANSISTOR
Q302RT1N441U-XTRANSISTOR
C1NCB31CK-104XC CAPACITOR0.1uF 16V K
C2NCB31CK-104XC CAPACITOR0.1uF 16V K
C3NCB31CK-104XC CAPACITOR0.1uF 16V K
C4NCB31CK-104XC CAPACITOR0.1uF 16V K
C5NCB31CK-104XC CAPACITOR0.1uF 16V K
C6NCB31CK-104XC CAPACITOR0.1uF 16V K
C7NCB31CK-104XC CAPACITOR0.1uF 16V K
C8NCB31CK-104XC CAPACITOR0.1uF 16V K
C9NCB31CK-104XC CAPACITOR0.1uF 16V K
C11NCB31CK-104XC CAPACITOR0.1uF 16V K
C12NCB31CK-104XC CAPACITOR0.1uF 16V K
C13NCB31CK-104XC CAPACITOR0.1uF 16V K
C14NCB31CK-104XC CAPACITOR0.1uF 16V K
C15NCB31CK-104XC CAPACITOR0.1uF 16V K
C16NCB31CK-104XC CAPACITOR0.1uF 16V K
C17NCB31CK-104XC CAPACITOR0.1uF 16V K
C18NCB31CK-104XC CAPACITOR0.1uF 16V K
C101NCB31CK-104XC CAPACITOR0.1uF 16V K
C102NCB31CK-104XC CAPACITOR0.1uF 16V K
C103NCB31CK-104XC CAPACITOR0.1uF 16V K
C104NCB31CK-104XC CAPACITOR0.1uF 16V K
C105NBE41AM-476XTA E CAPACITOR47uF 10V M
C106NBE41AM-476XTA E CAPACITOR47uF 10V M
C108NBE41AM-476XTA E CAPACITOR47uF 10V M
C111NCB31CK-104XC CAPACITOR0.1uF 16V K
C112NCB31CK-104XC CAPACITOR0.1uF 16V K
C201NEAF1CM-107XE CAPACITOR100uF 16V M
C202NCB31CK-104XC CAPACITOR0.1uF 16V K
C203NCB31HK-271XC CAPACITOR270pF 50V K
C204NDC31HJ-151XC CAPACITOR150pF 50V J
C205NCB31HK-681XC CAPACITOR680pF 50V K
C206NCB31HK-561XC CAPACITOR560pF 50V K
C211NEAF1CM-107XE CAPACITOR100uF 16V M
C212NCB31CK-104XC CAPACITOR0.1uF 16V K
C213NCB31CK-104XC CAPACITOR0.1uF 16V K
C221NCB31HK-223XC CAPACITOR0.022uF 50V K
C222NCB31HK-103XC CAPACITOR0.01uF 50V K
C251NCB31CK-104XC CAPACITOR0.1uF 16V K
C252NEAF1CM-107XE CAPACITOR100uF 16V M
C253NCB31CK-104XC CAPACITOR0.1uF 16V K
C254NBE21AM-106XTA E CAPACITOR10uF 10V M
C255NCB31CK-104XC CAPACITOR0.1uF 16V K
C256NCB31CK-473XC CAPACITOR0.047uF 16V K
C257NCB31HK-102XC CAPACITOR1000pF 50V K
C258NCB31HK-102XC CAPACITOR1000pF 50V K
C259NCB31HK-102XC CAPACITOR1000pF 50V K
C264NCB31HK-103XC CAPACITOR0.01uF 50V K
C265NCB31CK-104XC CAPACITOR0.1uF 16V K
C266NCB31CK-104XC CAPACITOR0.1uF 16V K
C267NCB31HK-103XC CAPACITOR0.01uF 50V K
C268NCB31HK-153XC CAPACITOR0.015uF 50V K
C301NEAF0JM-227XE CAPACITOR220uF 6.3V M
C302NBE40JM-476XTA E CAPACITOR47uF 6.3V M
C305NCB31CK-104XC CAPACITOR0.1uF 16V K
C308NCB31CK-104XC CAPACITOR0.1uF 16V K
C309NCB31CK-104XC CAPACITOR0.1uF 16V K
C310NCB31HK-103XC CAPACITOR0.01uF 50V K
C311NCB31CK-104XC CAPACITOR0.1uF 16V K
C312NCB21CK-105XC CAPACITOR1uF 16V K
C313NCB31CK-104XC CAPACITOR0.1uF 16V K
C315NCB31CK-104XC CAPACITOR0.1uF 16V K
C316NCB31CK-105XC CAPACITOR1uF 16V K
C317NCB31CK-104XC CAPACITOR0.1uF 16V K
C318NCB31CK-104XC CAPACITOR0.1uF 16V K
C319NCB31CK-104XC CAPACITOR0.1uF 16V K
C320NCB31CK-104XC CAPACITOR0.1uF 16V K
C321NCB31CK-104XC CAPACITOR0.1uF 16V K
C322NCB31CK-104XC CAPACITOR0.1uF 16V K
3-42
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
Part No.Part NameDescriptionLocal
C323NCB31CK-104XC CAPACITOR0.1uF 16V K
C324NCB21CK-105XC CAPACITOR1uF 16V K
C325NDC31HJ-120XC CAPACITOR12pF 50V J
C326NDC31HJ-120XC CAPACITOR12pF 50V J
C330NCB31CK-104XC CAPACITOR0.1uF 16V K
C331NCB31CK-333XC CAPACITOR0.033uF 16V K
C332NCB31CK-104XC CAPACITOR0.1uF 16V K
C333NCB31CK-104XC CAPACITOR0.1uF 16V K
C335NCB31CK-104XC CAPACITOR0.1uF 16V K
C336NCB31CK-104XC CAPACITOR0.1uF 16V K
C337NCB31HK-183XC CAPACITOR0.018uF 50V K
C338NCB31HK-562XC CAPACITOR5600pF 50V K
C339NCB31CK-104XC CAPACITOR0.1uF 16V K
C340NCB21CK-105XC CAPACITOR1uF 16V K
C341NCB21CK-105XC CAPACITOR1uF 16V K
C347NCB31CK-104XC CAPACITOR0.1uF 16V K
C348NCB31CK-104XC CAPACITOR0.1uF 16V K
C349NCB31CK-104XC CAPACITOR0.1uF 16V K
C350NCB31CK-104XC CAPACITOR0.1uF 16V K
C358NDC31HJ-5R0XC CAPACITOR5pF 50V J
C359NDC31HJ-5R0XC CAPACITOR5pF 50V J
C364NBE40JM-476XTA E CAPACITOR47uF 6.3V M
C365NCB31CK-104XC CAPACITOR0.1uF 16V K
C366NCB21CK-105XC CAPACITOR1uF 16V K
C369NBE40JM-476XTA E CAPACITOR47uF 6.3V M
C371NCB21CK-105XC CAPACITOR1uF 16V K
C380NCB31CK-104XC CAPACITOR0.1uF 16V K
C381NCB31CK-104XC CAPACITOR0.1uF 16V K
C382NCB31CK-104XC CAPACITOR0.1uF 16V K
C383NCB31CK-104XC CAPACITOR0.1uF 16V K
C391NCB31CK-104XC CAPACITOR0.1uF 16V K
C392NCB31CK-104XC CAPACITOR0.1uF 16V K
C393NCB31CK-104XC CAPACITOR0.1uF 16V K
C394NCB31CK-104XC CAPACITOR0.1uF 16V K
C396NCB31CK-104XC CAPACITOR0.1uF 16V K
C397NBE20JM-226XTA E CAPACITOR22uF 6.3V M
C401NCB31CK-104XC CAPACITOR0.1uF 16V K
C402NBE41AM-476XTA E CAPACITOR47uF 10V M
C403NCB31HK-331XC CAPACITOR330pF 50V K
C404NCB31CK-473XC CAPACITOR0.047uF 16V K
C411NCB31CK-104XC CAPACITOR0.1uF 16V K
C412NBE41CM-336XTA E CAPACITOR33uF 16V M
C421NCB31CK-104XC CAPACITOR0.1uF 16V K
C422NBE41AM-476XTA E CAPACITOR47uF 10V M
C431NCB31HK-332XC CAPACITOR3300pF 50V K
C432NCS31HJ-471XC CAPACITOR470pF 50V J
C433NCS31HJ-471XC CAPACITOR470pF 50V J
C451NCB31CK-104XC CAPACITOR0.1uF 16V K
C452NCB31CK-104XC CAPACITOR0.1uF 16V K
C453NCB31CK-104XC CAPACITOR0.1uF 16V K
C454NCB31CK-104XC CAPACITOR0.1uF 16V K
C481NCB31CK-104XC CAPACITOR0.1uF 16V K
C491NCB31CK-104XC CAPACITOR0.1uF 16V K
C521NCB31CK-104XC CAPACITOR0.1uF 16V K
C522NBE41AM-476XTA E CAPACITOR47uF 10V M
C531NCB31HK-332XC CAPACITOR3300pF 50V K
C532NCS31HJ-471XC CAPACITOR470pF 50V J
C533NCS31HJ-471XC CAPACITOR470pF 50V J
Q1012SB1424/R/-WTRANSISTOR
Q1022SC4617/R/-XTRANSISTOR
Q1032SB1424/R/-WTRANSISTOR
Q1042SC4617/R/-XTRANSISTOR
Q1052SK3019-XMOS FET
Q1062SK3019-XMOS FET
Q1072SC4617/R/-XTRANSISTOR
Q231DTC114EE-XDIGI TRANSISTOR
Q301DTC144EE-XDIGI TRANSISTOR
Q302DTC144EE-XDIGI TRANSISTOR
C1NCB31CK-104XC CAPACITOR0.1uF 16V K
C2NCB31CK-104XC CAPACITOR0.1uF 16V K
C3NCB31CK-104XC CAPACITOR0.1uF 16V K
C4NCB31CK-104XC CAPACITOR0.1uF 16V K
C5NCB31CK-104XC CAPACITOR0.1uF 16V K
C6NCB31CK-104XC CAPACITOR0.1uF 16V K
C7NCB31CK-104XC CAPACITOR0.1uF 16V K
C8NCB31CK-104XC CAPACITOR0.1uF 16V K
C9NCB31CK-104XC CAPACITOR0.1uF 16V K
C10NCB31CK-104XC CAPACITOR0.1uF 16V K
C11NCB31CK-104XC CAPACITOR0.1uF 16V K
C12NCB31CK-104XC CAPACITOR0.1uF 16V K
C13NCB31CK-104XC CAPACITOR0.1uF 16V K
C14NCB31CK-104XC CAPACITOR0.1uF 16V K
C15NCB31CK-104XC CAPACITOR0.1uF 16V K
C16NCB31CK-104XC CAPACITOR0.1uF 16V K
C17NCB31CK-104XC CAPACITOR0.1uF 16V K
C18NCB31CK-104XC CAPACITOR0.1uF 16V K
C19NCB31CK-104XC CAPACITOR0.1uF 16V K
C20NCB31CK-104XC CAPACITOR0.1uF 16V K
C21NCB31CK-104XC CAPACITOR0.1uF 16V K
C102NCB31CK-104XC CAPACITOR0.1uF 16V K
C103NCB31CK-104XC CAPACITOR0.1uF 16V K
C104NCB31CK-104XC CAPACITOR0.1uF 16V K
C105NBE41AM-476XTA E CAPACITOR47uF 10V M
C106NBE41AM-476XTA E CAPACITOR47uF 10V M
C108NBE41AM-476XTA E CAPACITOR47uF 10V M
C111NCB31CK-104XC CAPACITOR0.1uF 16V K
C112NCB31CK-104XC CAPACITOR0.1uF 16V K
C113NCB31CK-104XC CAPACITOR0.1uF 16V K
C201NEAF1CM-107XE CAPACITOR100uF 16V M
C202NCB31CK-104XC CAPACITOR0.1uF 16V K
C203NCS31HJ-271XC CAPACITOR270pF 50V J
C204NDC31HJ-151XC CAPACITOR150pF 50V J
C205NCB31HK-681XC CAPACITOR680pF 50V K
C206NCB31HK-561XC CAPACITOR560pF 50V K
Part No.Part NameDescriptionLocal
3-44
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
Part No.Part NameDescriptionLocal
C211NEAF1CM-107XE CAPACITOR100uF 16V M
C212NCB31CK-104XC CAPACITOR0.1uF 16V K
C213NCB31CK-104XC CAPACITOR0.1uF 16V K
C221NCB31HK-223XC CAPACITOR0.022uF 50V K
C222NCB31HK-103XC CAPACITOR0.01uF 50V K
C251NCB31CK-104XC CAPACITOR0.1uF 16V K
C252NEAF1CM-107XE CAPACITOR100uF 16V M
C253NCB31CK-104XC CAPACITOR0.1uF 16V K
C254NBE21AM-106XTA E CAPACITOR10uF 10V M
C255NCB31CK-104XC CAPACITOR0.1uF 16V K
C256NCB31CK-473XC CAPACITOR0.047uF 16V K
C257NCB31HK-102XC CAPACITOR1000pF 50V K
C258NCB31HK-102XC CAPACITOR1000pF 50V K
C259NCB31HK-102XC CAPACITOR1000pF 50V K
C264NCB31HK-103XC CAPACITOR0.01uF 50V K
C265NCB31CK-104XC CAPACITOR0.1uF 16V K
C266NCB31CK-104XC CAPACITOR0.1uF 16V K
C267NCB31HK-103XC CAPACITOR0.01uF 50V K
C268NCB31HK-153XC CAPACITOR0.015uF 50V K
C301NEAF0JM-227XE CAPACITOR220uF 6.3V M
C302NBE40JM-476XTA E CAPACITOR47uF 6.3V M
C305NCB31CK-104XC CAPACITOR0.1uF 16V K
C307NCB31CK-104XC CAPACITOR0.1uF 16V K
C308NCB31CK-104XC CAPACITOR0.1uF 16V K
C309NCB31CK-104XC CAPACITOR0.1uF 16V K
C310NCB31HK-102XC CAPACITOR1000pF 50V K
C311NCB31CK-104XC CAPACITOR0.1uF 16V K
C312NCB21CK-105XC CAPACITOR1uF 16V K
C313NCB31CK-104XC CAPACITOR0.1uF 16V K
C314NCB31CK-104XC CAPACITOR0.1uF 16V K
C315NCB31CK-104XC CAPACITOR0.1uF 16V K
C316NCB31CK-104XC CAPACITOR0.1uF 16V K
C317NCB31CK-104XC CAPACITOR0.1uF 16V K
C318NCB31CK-104XC CAPACITOR0.1uF 16V K
C319NCB31CK-104XC CAPACITOR0.1uF 16V K
C320NCB31CK-104XC CAPACITOR0.1uF 16V K
C321NCB31CK-104XC CAPACITOR0.1uF 16V K
C322NCB31CK-104XC CAPACITOR0.1uF 16V K
C323NCB31CK-104XC CAPACITOR0.1uF 16V K
C324NCB21CK-105XC CAPACITOR1uF 16V K
C325NDC31HJ-100XC CAPACITOR10pF 50V J
C326NDC31HJ-100XC CAPACITOR10pF 50V J
C330NCB31CK-104XC CAPACITOR0.1uF 16V K
C331NCB31CK-333XC CAPACITOR0.033uF 16V K
C332NCB31CK-104XC CAPACITOR0.1uF 16V K
C333NCB31CK-104XC CAPACITOR0.1uF 16V K
C334NCB31CK-104XC CAPACITOR0.1uF 16V K
C335NCB31CK-104XC CAPACITOR0.1uF 16V K
C336NCB31CK-104XC CAPACITOR0.1uF 16V K
C337NCB31HK-183XC CAPACITOR0.018uF 50V K
C338NCB31HK-562XC CAPACITOR5600pF 50V K
C339NCB31CK-104XC CAPACITOR0.1uF 16V K
C340NCB21CK-105XC CAPACITOR1uF 16V K
C341NCB21CK-105XC CAPACITOR1uF 16V K
C347NCB31CK-104XC CAPACITOR0.1uF 16V K
C348NCB31CK-104XC CAPACITOR0.1uF 16V K
C349NCB31CK-104XC CAPACITOR0.1uF 16V K
C350NCB31CK-104XC CAPACITOR0.1uF 16V K
C356NCB21CK-105XC CAPACITOR1uF 16V K
C358NDC31HJ-5R0XC CAPACITOR5pF 50V J
C359NDC31HJ-5R0XC CAPACITOR5pF 50V J
C364NBE40JM-476XTA E CAPACITOR47uF 6.3V M
C365NCB31CK-104XC CAPACITOR0.1uF 16V K
C366NCB21CK-105XC CAPACITOR1uF 16V K
C369NBE40JM-476XTA E CAPACITOR47uF 6.3V M
C371NCB21CK-105XC CAPACITOR1uF 16V K
C380NCB31CK-104XC CAPACITOR0.1uF 16V K
C384NCB31CK-104XC CAPACITOR0.1uF 16V K
C391NCB31CK-104XC CAPACITOR0.1uF 16V K
C392NCB31CK-104XC CAPACITOR0.1uF 16V K
C393NCB31CK-104XC CAPACITOR0.1uF 16V K
C395NCB31CK-104XC CAPACITOR0.1uF 16V K
C396NCB31CK-104XC CAPACITOR0.1uF 16V K
C397NBE20JM-226XTA E CAPACITOR22uF 6.3V M
C398NCB31CK-104XC CAPACITOR0.1uF 16V K
C399NCB31CK-104XC CAPACITOR0.1uF 16V K
C401NCB31CK-104XC CAPACITOR0.1uF 16V K
C402NBE41AM-476XTA E CAPACITOR47uF 10V M
C403NCB31HK-331XC CAPACITOR330pF 50V K
C404NCB31CK-473XC CAPACITOR0.047uF 16V K
C411NCB31CK-104XC CAPACITOR0.1uF 16V K
C412NBE41AM-476XTA E CAPACITOR47uF 10V M
C421NCB31CK-104XC CAPACITOR0.1uF 16V K
C422NBE41AM-476XTA E CAPACITOR47uF 10V M
C431NCB31HK-332XC CAPACITOR3300pF 50V K
C432NCS31HJ-471XC CAPACITOR470pF 50V J
C433NCS31HJ-471XC CAPACITOR470pF 50V J
C451NCB31CK-104XC CAPACITOR0.1uF 16V K
C452NCB31CK-104XC CAPACITOR0.1uF 16V K
C453NCB31CK-104XC CAPACITOR0.1uF 16V K
C454NCB31CK-104XC CAPACITOR0.1uF 16V K
C481NCB31CK-104XC CAPACITOR0.1uF 16V K
C491NCB31CK-104XC CAPACITOR0.1uF 16V K
C492NCB31CK-104XC CAPACITOR0.1uF 16V K
C521NCB31CK-104XC CAPACITOR0.1uF 16V K
C522NBE41AM-476XTA E CAPACITOR47uF 10V M
C531NCB31HK-332XC CAPACITOR3300pF 50V K
C532NCS31HJ-471XC CAPACITOR470pF 50V J
C533NCS31HJ-471XC CAPACITOR470pF 50V J
No additional / supplemental order of WARRANTY CARDs are available
Block No.
3
M
M
M
P3
A1
A3
A17
A18
A19
A24
ADV5380J,DV5300J
P3
A1 A3
A4
DV5301EU,
DV5302EU,
DV5305U,
DV5306U,
DV4305U,
DV4306U,
P4
P3
A1 A3
A4
A17
A20
A21
DV5301E,
DV5302E,
P2
A6
P3
A1
A3
A17
A21
DV5308EE,
DV5307EE,
A5
P3
A1
A3
DV5305UN,UT,A,
DV5304UI,
DV5306UN,UT,A,
DV4304UI,
DV4306UN,UT,A,
DV4305UN,UT,A,
DV4388UF,
P4
P3
A2
DV5305U,
DV5306U,
DV4305U,
DV4306U,
DV5301,
DV5302,
DVH426UN,
except DVH426UN
only DVH426UN
P1
P7
KIT :
A7,
A10,
except DVH426UN
P7
KIT :
A15
A14
A8, A9,
A12
A11,
P6
A22,
A23,
only DVH426UN
The parts without symbol number are not service.
A16
P5
A13
3-47
Packing and Accessories
Block No. [M][3][M][M]
Symbol No.Part No.Part NameDescriptionLocal
A 1GET0444-001AINST BOOKENG FRE SPAADV5380J,DV5300J
A 1GET0442-002AINST BOOKSPA ITA SWE PORDV5301E,DV5302E
A 1GET0442-003AINST BOOKENG FREDV5301EU,DV5302EU
A 1GET0440-001AINST BOOKENGDV5304UI,DV4304UI
A 1GET0439-001AINST BOOKENG CHI(TAIWAN)DV5305U,DV5306U,DV4305U,DV4306U
A 1GET0439-003AINST BOOKENG INA
A 1GET0439-004AINST BOOKENG CHI(TAIWAN)
A 1GET0439-005AINST BOOKENGDV5305A,DV5306A,DV4305A,DV4306A
A 1GET0443-001AINST BOOKENG RUS UKRDV5307EE,DV5308EE
A 1GET0441-001AINST BOOKCHI(PEKIN)DV5388UF,DV4388UF
A 1GET0473-001AINST BOOKENGDVH426UN
A 2GET0442-001AINST BOOKENG GER FRE DUTDV5301E,DV5302E
A 2GET0442-004AINST BOOKSPA TUR PERDV5301EU,DV5302EU
A 2GET0439-002AINST BOOKKOR THA ARA PERDV5305U,DV5306U,DV4305U,DV4306U
A 3GET0444-002AINSTALL MANUALENG FRE SPAADV5380J,DV5300J
A 3GET0442-005AINSTALL MANUALENG GER FRE DUTDV5301E,DV5302E
A 3GET0442-007AINSTALL MANUALENG FREDV5301EU,DV5302EU
A 3GET0440-002AINSTALL MANUALENGDV5304UI,DV4304UI
A 3GET0439-006AINSTALL MANUALENG CHI(TAIWAN)
A 3GET0439-008AINSTALL MANUALENG INA
A 3GET0439-009AINSTALL MANUALENGDV5305A,DV5306A,DV4305A,DV4306A
A 3GET0443-002AINSTALL MANUALENG RUS UKRDV5307EE,DV5308EE
A 3GET0441-002AINSTALL MANUALCHI(PEKIN)DV5388UF,DV4388UF
A 4GET0442-006AINSTALL MANUALSPA ITA SWE PORDV5301E,DV5302E
A 4GET0442-008AINSTALL MANUALSPA TUR PERDV5301EU,DV5302EU
A 4GET0439-007AINSTALL MANUALKOR THA ARA PERDV5305U,DV5306U,DV4305U,DV4306U
KITSRW-424SCREW PARTS KITA22 A23DVH426UN
P 1GE32610-001ACARTONADV5380J
P 1GE32607-001ACARTONDV5300J
P 1GE32598-002ACARTONDV5301E,DV5301EU
P 1GE32601-002ACARTONDV5302E,DV5302EU
P 1GE32626-002ACARTONDV5304UI
P 1GE32615-002ACARTONDV5305U,DV5305UN,DV5305UT,DV5305A
P 1GE32618-002ACARTONDV5306U,DV5306UN,DV5306UT,DV5306A
P 1GE32604-002ACARTONDV5307EE
P 1GE32794-001ACARTONDV5308EE
P 1GE32629-001ACARTONDV5388UF
P 1GE32592-002ACARTONDV4304UI
P 1GE32553-002ACARTONDV4305U,DV4305UN,DV4305UT,DV4305A
P 1GE32556-002ACARTONDV4306U,DV4306UN,DV4306UT,DV4306A
P 1GE32595-001ACARTONDV4388UF
P 1GE32804-001ACARTONDVH426UN
P 2QPC03004315PPOLY BAG30cm x 43cm
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)
Contents
Block diagram
Standard schematic diagrams
Printed circuit boards
KD-DVH426
except
KD-DVH426
2-1
2-2
2-12 to 14
only for
KD-ADV5380
KD-DV5300
only for
KD-DV5308
KD-DV5307
KD-DV5302
KD-DV5301
COPYRIGHT 2007 Victor Company of Japan, Limited.
No.MA308SCH
2007/3
Safety precaution
!
!
Burrs formed during molding may be left over on some parts of the chassis. Therefore,
pay attention to such burrs in the case of preforming repair of this system.
Please use enough caution not to see the beam directly or touch it in case of an
adjustment or operation check.
Block diagram
FOCUS
&
TRACKING
COIL
PICK UP
LOAD
&
FEED
MOTOR
SPINDLE
MOTOR
AUX
INPUT
DVD section
SW1
to
SW3
CD VR, DVD VR
CD/DVD
CN101
M
CN201
M
A, B, C, D, E, F, RF+/LPC1, LPC2, HAGUP
DVD LD
CD LD
F+/T+/-
FLM+/-
H1+/-, H2+/H3+/-, VH
SM1 to SM3
IC398
FLASH ROM
SW2
CN202
SW3
SW1
TRVSW
SW4,SW5
L-END SW
REST SW
Q105 to Q107
Q101
Q102
Q103
Q104
IC201
DRIVER
IC251
SP MOTOR
DRIVER
IC399
SDRAM
EXADT0 to EXADT15
EXADR16 to EXADR20
EXDAT0 to EXDAT15
NEXOE, NEXCE
NEXWE, /FL_RST
SW4
Used For KD-DVH426
CPURST
LPCO1
DVDLDCUR
LPCO2
CDLDCUR
/DRVMUTE
TRDRV
FODRV
TRSDRV
DRVCONT
LDIN
Q231
SPDRV
/SPMUTE
FG
MA0 to MA11
MDQ0 to MDQ15
DQM0 to DQM1
BA0, BA1, MCK
NWE, NCSM
NCAS, NRAS
LM
IC301
DV3.2
(DV2.1)
UCS
SCS
SCLK
U2SDT
S2UDT
CPURST
LRMUTE
TX
DAC4OUT
IC411
L.P.F.
IC401
DAC
EPDIO
EPSK
EPCS
AOUTL+/AOUTR+/-
PCMCLK
BCK
AOUT3
LRCLK
DACPDN
DACOCS
DCLK
DDATA
IC481
EPROM
X351
27.000MHz
D1.2V
IC302
Q301
2V to
1.2V REG.
Q302
D2V
NOTES:
Ref No.'s ( ) indicate a "Used for KD-DVH426"
LCD & Key switch section
Used for except KD-DVH426
D631 to D651
LIGHTING DISPLAY
Used for KD-DVH426
D631 to D633
D635
D637 to D654
LIGHTING DISPLAY
D630
POWER LED
J601
AUX.L/R
Used for
KD-ADV5380, KD-DV5300, KD-DV5304, KD-DV5305, KD-DV5306, KD-DV5388
ACC5V
ILMI.10V
Q670,Q671
DIMMER
CONT
LCD1
LCD DISPLAY
DIMOUT
ILMI.10V
S1 to S52
COM1 to COM3
JS686
ENCODER
ENC1
ENC2
IC661
LCD DRIVER
IC304
RESET
L-CH
R-CH
LCDDA
LCDCL
LCDCE
SW1
SW4
IC681
REMOCON
S601 to S618
KEY MATRIX
CN962
CN403
FAN
MOTOR
REMOCON
KEY0
KEY1
KEY2
J1
ANT
DIGITAL
OUT
OE
REMOTE
M
Main amplifier & System control section
TU1
FM/AM TUNER
MPX
IC71
RDS DETECTOR
Used for
KD-DV5301, KD-DV5302, KD-DV5307
CN961
CN963
IC402
TX
IC401
DIGITAL OUT
CN831
STEERING
Used For
KD-DV5301, KD-DV5302, KD-ADV5380
CN821
Q821 to Q823
FAN
CONTROL
D3.3V,S3.3V
IC921
3.3V REG.
D5V,M5V,S5V
IC922
5V REG.
MEMORY
KEY0 to KEY2
DIMOUT
LCDCL
LCDDA
CN701
CJ601
LCDCE
ENC1,ENC2
REMOCON
AUX.L/R
NOTES: Ref No.'s ( ) indicate a "Used for KD-DVH426"
FSU, SSTOP, TUSDA, TUSCL, Q-OUT, AFS
RDSDA
RDSSCK
X71
4.332MHz
UCS
SCS
SCLK
U2SDT
S2UDT
LRMUTE
CPURST
IC961
IC962
LEVEL
CONV.
DOUTMUTE
FAN
IC731,S731
(IC723,S723)
RESET
X722 20MHz
(X721 12.5MHz)
X721(X722)
32.768kHz
IC722
EPROM
Used For
KD-DV5301
KD-DV5302
KD-DV5307
KD-DVH426
SWREG
A5V,A9V
Q971,Q972
(Q903,Q904)
DVD SW
9V
SW1, SW4
UCS
SCS
SCLK
U2SDT
S2UDT
LRMUTE
CPURST
RESET
SCL
SDA
DVDSW
IC721
CPU
DVD.L/R
VOLDA
VOLCLK
MUTING
Q861(Q781)
MUTE
TELMUTE
TELCONT
Used for
Q891,Q892
TEL MUTE
KD-DV5301
KD-DV5302
KD-DV5307
PBRK
Q885
PAR K
Used for
except KD-DVH426
DIM
Q911,Q912
ANTCONT, POWERON
PS2
Q976,Q977
PS2
BUSSI
BUSSO
BUSIO
BUSINT
BUSSCK
IC801
JVC BUS
A/L/CH
Used for
KD-ADV5380
KD-DV5300
KD-DV5301
KD-DV5302
KD-DV5304
KD-DV5305
KD-DV5306
KD-DV5388
Used for
KD-ADV5380
KD-DV5300
COMPOSITE(DAC4OUT)
TU.L/R
IC161
E.VOLUME
IN3L/R
TEL
VDD, SW5V, ACC5V
9V, CD8V, ILMI.10V
EACH BLOCK
ILM.AJ
IC911
(IC901)
REGULATOR
MEMORY
OUT1/3
IC151
Q151,Q152
AUX_LINEIN/CH SW
IC101
AUX/LINEIN AMP.
IN3_L/R
A/L
IC111,Q121
AUX/LINEIN
SW
Used for
KD-DV5304, KD-DV5305
KD-DV5306, KD-DV5388
Q303
VMUTE
IC411
VIDEO
AMP
Q344,Q354
LINE OUT
MUTING
RL, RR
FL, FR
IC301
POWER
AMP.
MUTE
ACC, EXT
ANT
Used for
KD-DV4304, KD-DV4305
KD-DV4306, KD-DV4388
KD-DV5304, KD-DV5305
KD-DV5306, KD-DV5388
KD-DVH426
Used for
KD-DV4304, KD-DV4305
KD-DV4306, KD-DV4388
KD-DV5307, KD-DVH426
Used for
KD-DV5301
KD-DV5302
ANTENNA
VIDEO-OUT
REAR L/R
FRONT L+/FRONT R+/REAR L+/REAR R+/-
MEMORY
AUTO ANT
D851
AUTO
SCK, BUSSI
CHL/R
LINEIN_L/R
VIDEO OUT
J331
LINE OUT
CN901
SPK
BATTERY
J801CN141
JVC BUS
Used for
KD-DV5301
KD-DV5302
KD-DV5304
KD-DV5305
KD-DV5306
KD-DV5388
LINE IN
2-1
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.