DVD/CD RECEIVER
DVD-/CD-RECEIVER
RÉCEPTEUR DVD/CD
DVD/CD-RECEIVER
KD-DV4402/KD-DV4401
NEDERLANDS FRANÇAIS DEUTSCH ENGLISH
For canceling the display demonstration, see page 5.
Zum Abbrechen der Displaydemonstration siehe Seite 5.
Pour annuler la démonstration des affichages, référez-vous à la page 5.
Zie bladzijde 5 voor het annuleren van de displaydemonstratie.
For installation and connections, refer to the separate manual.
Für den Einbau und die Anschlüsse siehe das eigenständige Handbuch. Pour l’installation et les raccordements, se référer au manuel séparé.
Bijzonderheden over de installatie en aansluiting van het apparaat vindt u in de desbetreffende handleiding.
INSTRUCTIONS
BEDIENUNGSANLEITUNG
MANUEL D’INSTRUCTIONS
GEBRUIKSAANWIJZING
GET0514-001A
[E]
ENGLISH
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit.
IMPORTANT FOR LASER PRODUCTS
1.CLASS 1 LASER PRODUCT
2.CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.
3.CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.
4.REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
[European Union only]
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
For safety...
•Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.
•Stop the car before performing any complicated operations.
Temperature inside the car...
If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.
WARNINGS:
(To prevent accidents and damage)
•DO NOT install any unit or wire any cable in a location where;
–it may obstruct the steering wheel and gearshift lever operations.
–it may obstruct the operation of safety devices such as air bags.
–it may obstruct visibility.
•DO NOT operate the unit while driving.
•If you need to operate the unit while driving, be sure to look around carefully.
•The driver must not watch the monitor while driving.
If the parking brake is not engaged, “DRIVER MUST NOT WATCH THE MONITOR WHILE DRIVING.” appears on the monitor, and no playback picture will be shown.
–This warning appears only when the parking brake lead is connected to the parking brake system built in the car (refer to the Installation/Connection Manual).
2
How to reset your unit
• Your preset adjustments will also be erased.
How to forcibly eject a disc
•Be careful not to drop the disc when it ejects.
•If this does not work, reset your unit.
How to use functions mode
If you press M MODE, the unit goes into functions mode, then the number buttons and 5/∞buttons work as different function buttons.
[Within 5 seconds...]
Caution on volume setting
Discs produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level.
Caution for DualDisc playback
The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of Non-DVD side of a DualDisc on this product may not be recommended.
CONTENTS |
|
INTRODUCTIONS |
|
Playable disc type ........................................ |
4 |
Preparation.................................................. |
5 |
OPERATIONS |
|
Basic operations |
|
• Using the control panel............................... |
6 |
• Using the remote controller (RM-RK252).... |
7 |
Listening to the radio................................... |
10 |
Searching for FM RDS programme |
|
—PTY Search........................................... |
11 |
Disc operations............................................. |
13 |
• Operations using the control panel............. |
14 |
• Operations using the remote controller |
|
(RM-RK252)................................................ |
16 |
EXTERNAL DEVICES |
|
Listening to the other external |
|
components.............................................. |
22 |
SETTINGS |
|
Selecting a preset sound mode .................... |
22 |
General settings — PSM ............................. |
24 |
Disc setup menu........................................... |
26 |
REFERENCES |
|
More about this unit .................................... |
28 |
Maintenance................................................ |
33 |
Troubleshooting........................................... |
34 |
Specifications............................................... |
36 |
For security reasons, a numbered ID card is provided with this unit, and the same ID number is imprinted on the unit’s chassis. Keep the card in a safe place, as it will help the authorities to identify your unit if stolen.
ENGLISH
3
ENGLISH
Playable disc type |
|
|
Disc type |
Recording format, file type, etc |
Playable |
DVD |
DVD-Video (Region Code : 2) *1 |
|
|
DVD-Audio |
|
|
DVD-ROM |
|
DVD Recordable/Rewritable |
DVD-Video |
|
(DVD-R/-RW *2, +R/+RW *3) |
DVD-VR |
|
• DVD Video: UDF bridge |
|
|
DivX/MPEG1/MPEG2 |
|
|
• DVD-VR |
|
|
|
|
|
• DivX/MPEG-1/MPEG-2/MP3/ |
MP3/WMA/WAV |
|
WMA/WAV: ISO 9660 level 1, |
AAC |
|
level 2, Romeo, Joliet |
|
|
JPEG/MPEG4 |
|
|
|
|
|
|
DVD+VR |
|
|
DVD-RAM |
|
Dual Disc |
DVD side |
|
|
Non-DVD side |
|
CD/VCD |
Audio CD/CD Text (CD-DA)/DTS-CD *4 |
|
|
VCD (Video CD) |
|
|
SVCD (Super Video CD) |
|
|
CD-ROM |
|
|
CD-I (CD-I Ready) |
|
CD Recordable/Rewritable |
CD-DA |
|
(CD-R/-RW) |
VCD (Video CD) |
|
• ISO 9660 level 1, level 2, Romeo, |
|
|
DivX/MPEG1/MPEG2 |
|
|
Joliet |
|
|
|
|
|
|
MP3/WMA/WAV |
|
|
AAC |
|
|
JPEG/MPEG4 |
|
*1 If you insert a DVD Video disc of an incorrect Region Code, “REGION CODE ERROR” appears on the monitor.
*2 DVD-R recorded in multi-border format is also playable (except for dual layer discs). DVD-RW dual layer discs are not playable.
*3 It is possible to play back finalized +R/+RW (Video format only) discs. +RW double layer discs are not playable. *4 To reproduce DTS sound, use the DIGITAL OUT terminal (see also pages 27 and 31).
4
Preparation
Cancel the display demonstration and set the clock
• See also page 24.
1 |
|
|
|
Turn on the power. |
|
|
|
|
|
|
|
|
|
|
2 |
|
|
|
Enter the PSM settings. |
|
|
|
||
|
|
|
|
|
3 |
|
|
|
Cancel the display demonstrations |
|
|
|
|
Select “DEMO,” then “DEMO OFF.” |
|
|
|
|
Set the clock |
|
|
|
|
|
|
|
|
|
Select “CLOCK HOUR,” then adjust the hour. |
|
|
|
|
Select “CLOCK MIN” (minute), then adjust the minute. |
|
|
|
|
Select “24H/12H,” then “24 HOUR” or “12 HOUR.” |
|
|
|
|
|
4 |
|
|
|
Finish the procedure. |
|
|
|
|
|
When the power is turned off: Check the current clock time
When the power is turned on: Change the display information
Indication language:
In this manual, English indications are used for purposes of explanation. You can select the indication language on the monitor on the “LANGUAGE” setting (see page 26).
Detaching the control panel |
Attaching the control panel |
ENGLISH
INTRODUCTIONS 5
ENGLISH
Basic operations
Using the control panel
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 |
DISC: Select title/program/playlist/folder. |
r • |
Adjust the sound mode. |
|||||||||
2 |
Eject disc. |
• Enter the PSM settings [Hold]. |
||||||||||
3 |
• Turn on the power. |
t Enter functions mode. |
||||||||||
|
• Turn off the power [Hold]. |
• Press M MODE, then one of the following buttons |
||||||||||
|
• Attenuate the sound (if the power is on). |
|
(within 5 seconds)... |
|||||||||
4 |
Volume control [Turn]. |
|
EQ |
: Select the sound mode. |
||||||||
5 |
Remote sensor |
|
MO |
: Turn on/off monaural reception. |
||||||||
6 |
• |
FM/AM: Select the band. |
|
SSM |
: Automatic station presetting [Hold]. |
|||||||
|
• |
DISC: Start/pause playback. |
|
RPT |
: Select repeat play. |
|||||||
7 |
Loading slot |
|
RND : Select random play. |
|||||||||
8 |
Display window |
|
5/∞: Skip 10 chapters/tracks. |
|||||||||
9 |
• Activate/deactivate TA Standby Reception. |
y • |
FM/AM: Select preset station. |
|||||||||
|
• Enter RDS programme search [HOLD]. |
• |
DISC: Select chapter/title/program/folder/track. |
|||||||||
p Change the display information. |
u AUX (auxiliary) input jack |
|||||||||||
q Detach the panel. |
|
|
|
|
|
|||||||
w Select the source. |
* You cannot select “DISC” as the playback source if there |
|||||||||||
|
FM/AM =DISC* =AUX IN =LINE IN |
is no disc in the unit. |
||||||||||
|
=(back to the beginning) |
|
|
|
|
|
e• FM/AM: Search for station.
• DISC: Select chapter/track.
6
Display window
ENGLISH
1 Tr (track) indicator
2Source display / Track number / Folder number / Disc number / Title number / PBC indicator / Time countdown indicator
3 DISC indicator
4 RDS indicators—AF, REG, TP, PTY
5Playback mode / item indicators— RND (random), (disc),
(folder), RPT (repeat)
6 Tuner reception indicators—ST (stereo), MO (monaural)
7Sound mode (c-EQ: custom equalizer) indicators —CLASSIC, HIP HOP, JAZZ, ROCK, POPS, USER
8 LOUD (loudness) indicator
9 EQ (equalizer) indicator
p Disc information indicators—
TAG (Tag information), (folder),
(track/file) q Main display (Time, menu, playback information)
Using the remote controller (RM-RK252)
Installing the battery
R03/LR03/AAA
Insert the batteries into the remote controller by matching the polarity (+ and –) correctly.
Caution:
Battery shall not be exposed to excessive heat such as sunshine, fire, or the like.
•If the effectiveness of the remote controller decreases, replace both batteries.
Before using the remote controller:
•Aim the remote controller directly at the remote sensor on the unit.
•DO NOT expose the remote sensor to bright light (direct sunlight or artificial lighting).
Continued on the next page
OPERATIONS 7
ENGLISH
1button
•Turns the power on if pressed briefly or attenuates the sound when the power is on.
•Turns the power off if pressed and held.
25/∞buttons
•FM/AM: Selects the preset stations.
•DISC:
–DVD-Video: Selects the title.
–DVD-VR: Selects the program/playlist.
–DivX/MPEG Video/MP3/WMA/WAV: Selects the folders if included.
4 / ¢
buttons
•FM/AM:
–Searches for stations automatically if pressed briefly.
–Searches for stations manually if pressed and held.
•DISC:
–Reverse skip/forward skip if pressed briefly.
–Reverse search/forward search if pressed and held.
3VOL (volume) + / – buttons
• Adjusts the volume level.
2nd VOL (volume) buttons
• Not applicable for this unit.
4* ASPECT button
• Not applicable for this unit.
5 PHONE button
• Not applicable for this unit.
6* SETUP button
• Enters disc setup menu (during stop).
7* TOP M (menu) button
•DVD-Video/DivX: Shows the disc menu.
•DVD-VR: Shows the Original Program screen.
•VCD: Resumes PBC playback.
8* OSD (on-screen display) button
• Shows the on-screen bar.
9SHIFT button
• Functions with other buttons.
8
pDISP (display) button
• Changes the display information.
q1/¡buttons
•DVD-Video/VCD: Slow motion playback (during pause).
•DivX/MPEG Video/MP3/WMA/WAV: Reverse search/forward search.
wSOURCE button
• Selects the source.
e3(play) / 8(pause) button
• DISC: Starts/pauses playback.
r (end call) button
• Not applicable for this unit.
BAND/7(stop) buttons
•FM/AM: Selects the bands.
•DISC: Stops playback.
t* RETURN button
• VCD: Returns to the PBC menu.
y* MENU button
•DVD-Video/DivX: Shows the disc menu.
•DVD-VR: Shows the Playlist screen.
•VCD: Resumes PBC playback.
u* %/fibuttons
• DVD-Video: Makes selection/settings.
@/#buttons
•DVD-Video: Makes selection/settings.
•DivX/MPEG Video: Skips back or forward by about five minutes.
ENT (enter) button
• Confirms selection.
i* DUAL button
• Not applicable for this unit.
oSURROUND button
• Not applicable for this unit.
DIRECT button
•DISC: Enters direct search mode for chapter/ title/program/playlist/folder/track when pressed with SHIFT button (see page 16 for details).
CLR (clear) button
•DISC: Erases the misentry when pressed with SHIFT button.
* Functions as number buttons/* (asterisk)/# (hatch) when pressed with SHIFT button.
–FM/AM: Selects the preset stations (1 – 6).
–DISC: Enters chapter/title/program/playlist folder/track number after entering search mode by pressing SHIFT and DIRECT (see page 16 for details).
ENGLISH
OPERATIONS 9
ENGLISH
Listening to the radio
1 |
|
|
|
Select “FM/AM.” |
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 |
|
|
|
Select the bands. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3 |
|
|
|
Search for a station to listen—Auto Search. |
||||||||||
|
|
|
|
Manual Search: Hold either one of the buttons until “M” flashes on the display, then press |
||||||||||
|
|
|
|
it repeatedly. |
||||||||||
|
|
|
|
• When receiving an FM stereo broadcast with sufficient signal strength, “ST” lights up |
||||||||||
|
|
|
|
on the display. |
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
When an FM stereo broadcast is hard to receive
Reception improves, but stereo effect will be lost.
• “MO” lights up on the display.
To restore the stereo effect, repeat the same procedure. “MONO OFF” appears and the MO indicator goes off.
FM station automatic presetting —SSM (Strong-station Sequential Memory)
You can preset up to six stations for each band.
1 While listening to an FM station...
2
Local FM stations with the strongest signals are searched and stored automatically in the selected FM band.
Manual presetting
Ex.: Storing FM station of 92.50MHz into preset number 4 of the FM1 band.
1
2
3
Preset number flashes for a while.
To listen to a preset station
10
Searching for FM RDS programme — PTY Search
1 |
Activate PTY Search. |
2 |
Select one of the PTY codes |
or |
(programme types). |
See the following for details. |
|
3 |
Start searching. |
|
If there is a station broadcasting a programme |
|
of the same PTY code as you have selected, that |
|
station is tuned in. |
ENGLISH
Storing your favorite programme types
You can store your favorite PTY codes into the number buttons.
1 Select a PTY code (see right column).
2 Select a preset number.
3Repeat steps 1 and 2 for storing other PTY codes.
4
Preset PTY codes in the number buttons (1 to 6):
PTY codes (available with the control dial):
NEWS, AFFAIRS, INFO, SPORT, EDUCATE, DRAMA, CULTURE, SCIENCE, VARIED, POP M (music), ROCK M (music), EASY M (music), LIGHT M (music), CLASSICS, OTHER M (music), WEATHER, FINANCE, CHILDREN, SOCIAL, RELIGION, PHONE IN, TRAVEL, LEISURE, JAZZ, COUNTRY, NATION M (music), OLDIES, FOLK M (music), DOCUMENT
Continued on the next page
OPERATIONS 11
ENGLISH
Activating/deactivating TA/PTY Standby Reception
TA Standby Reception |
Indicator |
PTY Standby Reception |
Indicator |
|
|
|
|
|
|
Press |
to activate. |
|
See page 25. |
|
|
|
|
|
|
The unit temporarily will switch to Traffic |
Lights up |
The unit temporarily will switch to your |
Lights up |
|
Announcement (TA), if available, from any |
|
favorite PTY programme from any source |
|
|
source other than AM. |
|
other than AM. |
|
|
The volume changes to the preset TA |
|
|
|
|
volume level if the current level is lower |
|
|
|
|
than the preset level (see page 25). |
|
|
|
|
|
|
|
|
|
Not yet activated. Tune in to another |
Flashes |
Not yet activated. Tune in to another |
Flashes |
|
station providing the RDS signals. |
|
station providing the RDS signals. |
|
|
|
|
|
|
|
Press |
to deactivate. |
Goes off |
Select “OFF” for the PTY code (see page 25) |
Goes off |
|
|
|
to deactivate. |
|
|
|
|
|
|
Tracing the same programme—Network-Tracking Reception
When driving in an area where FM reception is not sufficient enough, this unit automatically tunes in to another FM RDS station of the same network, possibly broadcasting the same programme with stronger signals (see the illustration on the right).
When shipped from the factory, Network-Tracking Reception is activated.
To change the Network-Tracking Reception setting, see “AF-REG” on page 25.
Programme A broadcasting on different frequency areas (01 – 05)
Automatic station selection—Programme Search
Usually when you press the number buttons, the preset station is tuned in.
If the signals from the FM RDS preset station are not sufficient for good reception, this unit, using the AF data, tunes in to another frequency broadcasting the same programme as the original preset station is broadcasting.
•The unit takes some time to tune in to another station using programme search.
•See also page 25.
12
Disc operations
Before performing any operations...
Turn on the monitor to watch the playback picture. If you turn on the monitor, you can also control playback of other discs by referring to the monitor screen. (See pages 18 – 21.)
The disc type is automatically detected, and playback starts automatically (for DVD: automatic start depends on its internal program).
If the current disc does not have any disc menu, all tracks will be played repeatedly until you change the source or eject the disc.
If “” appears on the monitor when pressing a button, the unit cannot accept the operation you have tried to do.
• In some cases, without showing “,” operations will not be accepted.
ENGLISH
1
2
Insert the disc.
Playback starts automatically.
Start playback if necessary.
Prohibiting disc ejection |
|
To stop play and eject the disc |
||
|
|
|
|
|
|
|
|
|
|
• Press SRC to listen to another playback source.
To cancel the prohibition, repeat the same procedure.
Continued on the next page
OPERATIONS 13
ENGLISH
Change the display information.
Current chapter number and Elapsed playing time =Current chapter number and Clock =Current title and chapter number =(back to the beginning)
Current chapter number and Elapsed playing time =Current chapter number and Clock =Current program (or playlist) number and chapter number =(back to the beginning)
Elapsed playing time =Folder number and Clock =Folder name =Track title =(back to the beginning)
Current track number and Elapsed playing time =Current track number and Clock =(back to the beginning)
Current track number and Elapsed playing time =Current track number and Clock =Album name/ performer (folder name*1) =Track title (file name*1) =(back to the beginning)
Current track number and Elapsed playing time =Current track number and Clock =Disc title/ performer*2 =Track title*2 =(back to the beginning)
Operations using the control panel
Pressing (or holding) the following buttons allows you to...
Disc type
|
|
|
|
(Number buttons)*5 |
|
|
[Press] Select chapter |
Select title |
During stop: Locate title |
|
|
[Hold] Reverse/fast-forward |
|
During play/pause: Locate |
|
|
chapter*3 |
|
chapter |
|
|
[Press] Select chapter |
Select program number/ |
During stop: Locate program |
|
|
[Hold] Reverse/fast-forward |
playlist number |
During play/pause: Locate |
|
|
chapter*3 |
|
chapter |
|
|
[Press] Select track |
Select folder |
Locate particular folder directly |
|
|
[Hold] Reverse/fast-forward track*4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
[Press] Select track |
— |
Locate particular track directly |
|
|
[Hold] Reverse/fast-forward track*3 |
(PBC not in use) |
|
|
|
|
||
|
|
[Press] Select track |
Select folder |
Locate particular folder directly |
|
|
[Hold] Reverse/fast-forward track*3 |
|
|
|
|
|
|
|
|
|
[Press] Select track |
— |
Locate particular track directly |
|
|
[Hold] Reverse/fast-forward track*3 |
|
|
|
|
|
|
14
After pressing M MODE, press the following buttons to...
Disc type |
|
|
|
|
Skip 10 chapters (during |
CHAPTER RPT: |
|
|
play or pause) |
Repeat current chapter |
— |
|
|
TITLE RPT: |
|
|
|
|
|
|
|
Repeat current title |
|
|
Skip 10 chapters (during |
CHAPTER RPT: |
|
|
play or pause) |
Repeat current chapter |
|
|
|
PROGRAM RPT: |
— |
|
|
Repeat current program (not |
|
|
|
available for Playlist Playback) |
|
|
Skip 10 tracks (within the |
TRACK RPT: |
FOLDER RND: |
|
same folder) |
Repeat current track |
Randomly play all tracks of |
|
|
FOLDER RPT: |
current folder, then tracks of |
|
|
Repeat current folder |
next folders |
|
|
|
ALL RND: |
|
|
|
Randomly play all tracks |
|
Skip 10 tracks (PBC not in |
TRACK RPT: |
ALL RND: |
|
use) |
Repeat current track (PBC not in |
Randomly play all tracks (PBC |
|
|
use) |
not in use) |
|
Skip 10 tracks (within the |
TRACK RPT: |
FOLDER RND: |
|
same folder) |
Repeat current track |
Randomly play all tracks of |
|
|
FOLDER RPT: |
current folder, then tracks of |
|
|
Repeat current folder |
next folders |
|
|
|
ALL RND: |
|
|
|
Randomly play all tracks |
|
Skip 10 tracks |
TRACK RPT: |
ALL RND: |
|
|
Repeat current track |
Randomly play all tracks |
• To cancel repeat play or random play, select “RPT OFF” or “RND OFF.” |
|
||
*1 |
If the file does not have Tag information or “TAG DISPLAY” is set to “TAG OFF” (see page 25), folder name and file |
||
|
name appear. TAG indicator will not light up. |
|
|
*2 |
“NO NAME” appears for an audio CD. |
|
|
*3 |
Search speed: |
|
|
*4 |
Search speed: |
|
|
*5 |
Press to select number 1 to 6; hold to select number 7 to 12. |
|
ENGLISH
OPERATIONS 15
ENGLISH
Operations using the remote controller (RM-RK252)
|
Disc |
/ |
|
Button |
|
|
|
|
|
Stop play |
Stop play |
|
|
Start play/Pause (if pressed during play) |
Start play/Pause (if pressed during play) |
|
|
• Reverse/forward chapter search*1 (No |
Reverse/forward track search*4 (No sound can |
|
|
sound can be heard.) |
be heard.) |
•Slow motion*2 during pause (No sound can be heard.)
* DVD-VR: Reverse slow motion does not work.
[Press] Select chapter (during play or pause) |
[Press] Select track |
[Hold] Reverse/fast-forward chapter search*3 |
[Hold] Reverse/fast-forward track search*5 |
|
(No sound can be heard.) |
|
|
• DVD-Video: Select title (during play or |
Select folder |
pause) |
|
• DVD-VR: Select program |
|
Select playlist (during play or |
|
pause) |
|
|
|
|
• Skip back or forward the scenes by about |
— |
five minutes |
|
• Select chapter |
To search for chapter/title/program/playlist/folder/track directly (DVD/DivX/MPEG Video/MP3/ WMA/WAV/CD)
1 While holding SHIFT, press DIRECT repeatedly to select the desired search mode.
DVD-Video :
DVD-VR :
DivX/MPEG Video :
MP3/WMA/WAV :
2 While holding SHIFT, press the number buttons (0 – 9) to enter the desired number. 3 Press ENT (enter) to confirm.
16
|
|
|
Stop play |
Stop play |
Stop play |
|
|
|
Start play/Pause (if pressed during |
Start play/Pause (if pressed during |
Start play/Pause (if pressed during |
play) |
play) |
play) |
|
|
|
Reverse/forward track search*1 |
Reverse/forward track search*1 |
Reverse/forward track search*1 |
• Forward slow motion*2 during |
|
|
pause. (No sound can be heard.) |
|
|
* Reverse slow motion does not work. |
|
|
|
|
|
[Press] Select track |
[Press] Select track |
[Press] Select track |
[Hold] Reverse/fast-forward track |
[Hold] Reverse/fast-forward track |
[Hold] Reverse/fast-forward track |
search*3 (No sound can be |
search*3 |
search*3 |
heard.) |
|
|
|
Select folder |
|
— |
|
— |
|
|
|
— |
— |
— |
|
|
|
ENGLISH
•For DivX/MPEG Video/MP3/WMA/WAV, track is searched within the same folder.
•For DVD-VR, program/playlist search is possible during Original program playback (PG)/Playlist playback (PL).
•To erase a misentry, press CLR (clear) while holding SHIFT.
•To return to the previous screen, press RETURN.
*1 |
Search speed: |
*2 |
Slow motion speed: |
*3 |
Search speed: |
*4 |
Search speed: |
*5 |
Search speed: |
Continued on the next page
OPERATIONS 17
ENGLISH
Using menu driven features... (DVD-Video/ DVD-VR)
1 Press TOP M/MENU to enter the menu screen.
2Press %/fi/@/#to select an item you want to start play.
3 Press ENT (enter) to confirm.
Canceling the PBC playback... (VCD)
1 During stop, press DIRECT while holding SHIFT.
2Hold SHIFT, then press the number buttons (0 – 9) to enter the desired number.
3 Press ENT (enter) to confirm.
• To resume PBC, press TOP M/MENU.
Operations using the on-screen bar
(DVD/DVD-VR/DivX/MPEG Video/VCD)
These operations are possible on the monitor using the remote controller.
1Show the on-screen bar (see page 19).
(twice)
2 Select an item.
3Make a selection.
If pop-up menu appears...
•To cancel pop-up menu, press RETURN.
•For entering time/numbers, see the following.
Entering time/numbers
Press %/fito change the number, then press @/#to move to the next entry.
•Each time you press %/fi, the number increases/ decreases by one value.
•After entering the numbers, press ENT (enter).
•It is not required to enter the zero and tailing zeros (the last two digits in the example below).
Ex.: Time search
DVD: _:_ _:_ _ (Ex.: 1:02:00)
Press %once, then #twice to go to the third entry, % twice, then press ENT (enter).
To remove the on-screen bar
18
On-screen bar
Ex.: DVD-Video
Information
Operation
1 Disc type
2 • DVD-Video/DTS-CD: Audio signal format type and channel
• VCD:PBC
3Playback mode*1
DVD-Video: T. RPT: Title repeat
C. RPT: Chapter repeat
DVD-VR: |
C. RPT: |
Chapter repeat |
|
PG. RPT: Program repeat |
|
DivX/MPEG Video: T. RPT: |
Track repeat |
|
|
F. RPT: |
Folder repeat |
|
A. RND: |
All random |
|
F. RND: |
Folder random |
VCD*2: |
T. RPT: |
Track repeat |
|
A. RND: |
All random |
4Playback information Current title/chapter
Current program/chapter
Current playlist/chapter
Current track
Current folder/track 5 Time indication
Elapsed playing time of the disc (For DVD-Video, elapsed playing time of the current title/program/ playlist.)
DVD-Video/DVD/VR: Remaining title/program/playlist time VCD: Remaining disc time
Elapsed playing time of the current chapter/track*3
Remaining time of the current chapter/track*3
6 Playback status
Play
Forward/reverse search
Forward/reverse slow-motion
Pause
Stop 7 Operation icons
Change time indication (see 5)
Time Search (Enter the elapsed playing time of the current title/program/ playlist or of the disc.)
Title Search (by its number)
Chapter Search (by its number)
Track Search (by its number)
Change the audio language or audio channel
Change or turn off the subtitle language
Change the view angle
Repeat play*1 Random play*1
*1 For repeat play/random play, see also page 15. *2 While PBC is not in use.
*3 Not applicable for DVD-VR.
ENGLISH
OPERATIONS 19
ENGLISH
Operations using the control screen
(DivX/MPEG Video/MP3/WMA/WAV/CD)
These operations are possible on the monitor using the remote controller.
1Show the control screen.
DivX/MPEG Video: Press 7during play. MP3/WMA/WAV/CD: Automatically appear during play.
2Select “Folder” column or “Track” column (except for CD).
3 Select a folder or track.
4Start playback.
DivX/MPEG Video: Press ENT (enter) or 3/8. MP3/WMA/WAV/CD: Playback starts automatically.
Control screen
Ex.: MP3/WMA/WAV disc
1 Current folder number/total folder number
2 Folder list with the current folder selected
3 Selected playback mode
4 Elapsed playing time of the current track
5 Operation mode icon ( 3, 7, 8, ¡, 1)
6Current track number/total number of tracks in the current folder (total number of tracks on the disc)
7 Track information
8 Track list with the current track selected
To select a playback mode
1 While control screen is displayed...
Playback mode selection screen appears on the folder list section of the control screen.
2 Select a playback mode.
3 Select an item.
REPEAT: |
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
RANDOM: |
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Mode |
Playback functions |
|||||||||
|
|
|
|
|
|
|
|
|
|
|
F. RPT |
Repeat current folder |
|||||||||
(folder repeat): |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
T. RPT |
Repeat current track |
|||||||||
(track repeat): |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
A. RND |
Randomly play all tracks |
|||||||||
(all random): |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
F. RND |
Randomly play all tracks of |
|||||||||
(folder random): |
current folder, then tracks of |
|||||||||
|
next folders |
|||||||||
|
|
|
|
|
|
|
|
|
|
|
4 Confirm the selection.
* Not selectable for CD.
20
Operations using the list screen
(DVD-VR/DivX/MPEG Video/MP3/WMA/WAV)
These operations are possible on the monitor using the remote controller.
Before playing, you can display the folder list/track list to confirm the contents and start playing a track.
1 Display the folder list while stop.
2Select an item from the folder list.
•Track list of the selected folder appears.
•To go back to the folder list, press RETURN.
3 Select a track to start playing.
or
3Current page/total number of the pages included in the list
4 Current folder/track (highlighted bar)
List screen (DVD-VR)
You can use ORIGINAL PROGRAM or PLAY LIST screen anytime while playing DVD-VR with its data recorded. 1 Select a list screen.
|
• MP3/WMA/WAV: Control screen appears (see |
|
|
|
|||||||||||||||
|
|
page 20). |
1 |
Program/playlist number |
|||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
List screen (DivX/MPEG Video/MP3/WMA/ |
2 |
Recording date |
|||||||||||||||||
3 |
Recording source (TV station, the input |
||||||||||||||||||
WAV) |
|||||||||||||||||||
|
terminal of the recording equipment, etc.) |
||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4 |
Start time of recording |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
5 |
Title of the program/playlist* |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
6 |
Current selection (highlighted bar) |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
7 |
Creating date of playlist |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
8 |
Number of chapters |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
9 |
Playback time |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
* The title of the original program or playlist may |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
not be displayed depending on the recording |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
Ex.: Folder list |
equipment. |
||||||||||||
|
|
|
|
|
|
|
|
|
|||||||||||
1 Current folder number/total folder number |
2 Select an item from the list. |
||||||||||||||||||
2 Current track number/total number of tracks in the |
|
|
|
||||||||||||||||
|
current folder |
|
|
|
|||||||||||||||
|
|
|
|
ENGLISH
OPERATIONS 21
ENGLISH
Listening to the other external components
You can connect an external component to:
•AUX (auxiliary) input jack on the control panel.
•LINE IN plugs on the rear.
1 |
|
|
|
Select “AUX IN” or “LINE IN.” |
|
|
|
|
|
2 |
|
|
— |
Turn on the connected component and start playing the source. |
3 |
|
|
|
Adjust the volume. |
|
|
|
|
|
|
|
|
|
|
4 |
|
|
— |
Adjust the sound as you want (see below and page 23). |
Connecting an external component to the AUX input jack
Portable audio player, etc.
3.5 mm stereo mini plug (not supplied)
Selecting a preset sound mode
You can select a preset sound mode suitable to the music genre (c-EQ: custom equalizer).
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
— |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Select a preset sound mode suitable |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
to the music genre (c-EQ: custom |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
equalizer). |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
22 EXTERNAL DEVICES & SETTINGS
Preset value setting for each sound mode
Sound mode |
|
Preset value |
|
|
|
|
|
||
BAS (bass) |
TRE (treble) |
LOUD (loudness) |
||
|
||||
|
|
|
|
|
USER |
00 |
00 |
OFF |
|
ROCK |
+03 |
+01 |
ON |
|
|
|
|
|
|
CLASSIC |
+01 |
–02 |
OFF |
|
POP |
+04 |
+01 |
OFF |
|
|
|
|
|
|
HIP HOP |
+02 |
00 |
ON |
|
|
|
|
|
|
JAZZ |
+02 |
+03 |
OFF |
|
|
|
|
|
|
|
|
|
|
ENGLISH
Adjusting the sound
You can adjust the sound characteristics to your preference.
1
2
BASS*1 |
–06 to +06 |
Adjust the bass. |
|
|
|
TREBLE*1 |
–06 to +06 |
Adjust the treble. |
|
|
|
FADER*2 |
R06 to F06 |
Adjust the front and rear speaker |
|
output balance. |
|
|
|
BALANCE |
L06 to R06 |
Adjust the left and right speaker |
|
output balance. |
|
LOUD*1 (loudness) |
LOUD ON or |
Boost low and high frequencies to |
LOUD OFF |
produce a well-balanced sound at low |
|
volume level. |
|
VOL ADJ*3 (volume adjust) |
–05 to +05; |
Adjust and store auto-adjustment |
initial: 00 |
volume level for each source, |
|
comparing to the FM volume level. |
|
VOLUME |
00 to 50 or |
Adjust the volume. |
00 to 30*4 |
*1 When you adjust the bass, treble, or loudness, the adjustment you have made is stored for the currently selected sound mode (c-EQ) including “USER.”
*2 If you are using a two-speaker system, set the fader level to “00.”
*3 You cannot make an adjustment for FM. “FIX” appears.
*4 Depending on the amplifier gain control setting. (See page 25 for details.)
SETTINGS 23
ENGLISH
General settings — PSM
You can change PSM (Preferred Setting Mode) items |
3 |
Select or adjust the selected PSM item. |
|||
listed in the table below and on page 25. |
|
|
|||
1 |
Enter the PSM settings. |
|
|
||
2 |
|
|
4 |
Repeat steps 2 and 3 to adjust other PSM |
|
|
|
||||
Select a PSM item. |
|||||
|
items if necessary. |
||||
|
|
|
|
||
|
|
|
5 |
Finish the procedure. |
Indications |
Item |
Setting, [reference page] |
||
|
( |
|
: Initial) |
|
|
|
|
|
|
DEMO |
• |
DEMO ON |
: The display demonstration will be activated automatically if no |
|
Display |
|
|
|
operation is done for about 20 seconds, [5]. |
demonstration |
• |
DEMO OFF |
: Cancels. |
|
|
|
|
|
|
CLOCK DISP*1 |
• |
CLOCK ON |
: The clock time is shown on the display at all times when the power is |
|
Clock display |
|
|
|
turned off. |
|
• |
CLOCK OFF |
: Cancels; pressing DISP will show the clock time for about 5 seconds |
|
|
|
|
|
when the power is turned off, [5]. |
|
|
|
|
|
CLOCK HOUR |
0 – 23 (1-12) |
[Initial: 0 (0:00)], [5]. |
||
Hour adjustment |
|
|
|
|
|
|
|
|
|
CLOCK MIN |
00 – 59 |
[Initial: 00 (0:00)], [5]. |
||
Minute adjustment |
|
|
|
|
24H/12H |
• |
24 HOUR |
: See also page 5 for setting. |
|
Time display mode |
• |
12 HOUR |
|
|
|
|
|
|
|
CLOCK ADJ *2 |
• |
AUTO |
: The built-in clock is automatically adjusted using the CT (clock time) |
|
Clock adjustment |
|
|
|
data in the RDS signal. |
|
• |
OFF |
: Cancels. |
|
|
|
|
|
|
24
Indications |
Item |
Setting, [reference page] |
||||||
|
|
( |
|
|
: Initial) |
|
|
|
|
|
|
|
|
|
|
|
|
AF-REG *2 |
• |
AF |
: |
|
When the currently received signals become weak, the unit switches |
|||
Alternative |
|
|
|
|
|
|
to another station or service (the programme may differ from the one |
|
frequency/ |
|
|
|
|
|
|
currently received), [12]. |
|
regionalization |
• |
AF REG |
: |
|
When the currently received signals become weak, the unit switches |
|||
reception |
|
|
|
|
|
|
to another station broadcasting the same programme. |
|
|
|
• |
OFF |
: |
|
Cancels. |
||
|
|
|
|
|
|
|
||
PTY-STANDBY |
OFF, PTY codes |
: |
|
Activates PTY Standby Reception with one of the PTY codes, [11, 12]. |
||||
PTY standby |
(see page 11) |
|
|
|
||||
|
|
|
|
|
||||
TA VOLUME |
VOLUME 00 – |
[Initial: VOLUME 15], [12]. |
||||||
Traffic |
VOLUME 50 (or |
|
|
|
||||
announcement |
VOLUME 00 – |
|
|
|
||||
volume |
VOLUME 30) *3 |
|
|
|
||||
P-SEARCH *2 |
• |
ON |
: |
|
Activates Programme Search, [12]. |
|||
Programme search |
• |
OFF |
: |
|
Cancels. |
|||
|
|
|
|
|
|
|
|
|
DIMMER |
• |
ON |
: |
|
Dims the display and button illumination. |
|||
Dimmer |
• |
OFF |
: |
|
Cancels. |
|||
|
|
|
|
|
|
|
||
TEL MUTING |
• |
MUTING 1/ |
: |
Select either one which mutes the sounds while using a cellular |
||||
Telephone muting |
|
|
MUTING 2 |
|
|
phone. |
||
|
|
• |
MUTING OFF |
: |
|
Cancels. |
||
|
|
|
|
|
|
|
|
|
SCROLL*4 |
• |
ONCE |
: |
|
Scrolls the displayed information once. |
|||
Scroll |
• |
AUTO |
: |
|
Repeats scrolling (at 5-second intervals). |
|||
|
|
• |
OFF |
: |
|
Cancels. |
||
|
|
|
|
|
|
• |
Pressing DISP for more than one second can scroll the display |
|
|
|
|
|
|
|
|
|
regardless of the setting. |
|
|
|
|
|
|
|||
TAG DISPLAY |
• |
TAG ON |
: Shows the Tag information while playing MP3/WMA/WAV tracks. |
|||||
Tag display |
• |
TAG OFF |
: |
|
Cancels. |
|||
AMP GAIN |
• |
LOW POWER |
: VOLUME 00 – VOLUME 30. (Select this if the maximum power of the |
|||||
Amplifier gain |
|
|
|
|
|
|
speaker is less than 50 W to avoid damaging the speaker.) |
|
control |
• |
HIGH POWER |
: VOLUME 00 – VOLUME 50. |
|||||
IF BAND |
• |
AUTO |
: |
Increases the tuner selectivity to reduce interference noises between |
||||
Intermediate |
|
|
|
|
|
|
adjacent stations. (Stereo effect may be lost.) |
|
frequency band |
• |
WIDE |
: |
Subject to interference noises from adjacent stations, but sound |
||||
|
|
|
|
|
|
|
|
quality will not be degraded and the stereo effect will remain. |
*1 |
If the power supply is not interrupted by turning off the ignition key of your car, it is recommended to select |
|||||||
|
“CLOCK OFF” to save the car’s battery. |
|
|
|
||||
*2 |
Only for RDS FM stations. |
|
|
|
||||
*3 |
Depending on the “AMP GAIN” setting. |
|
|
|
||||
*4 |
Some characters or symbols will not be shown correctly (or will be blanked) on the display. |
ENGLISH
SETTINGS 25
ENGLISH
Disc setup menu
These operations are possible on the monitor using the remote controller.
1 Enter the disc setup menu while stop.
2 Select a menu.
3 Select an item you want to set up.
• To cancel pop-up menu, press RETURN.
4 Select an option.
To return to normal screen
Menu |
Item |
Setting |
|
MENU |
Select the initial disc menu language. Refer also to “Language codes” on page 32. |
|
LANGUAGE |
|
LANGUAGE
AUDIO |
Select the initial audio language. Refer also to “Language codes” on page 32. |
LANGUAGE |
|
|
|
SUBTITLE |
Select the initial subtitle language or remove the subtitle (OFF). Refer also to |
|
“Language codes” on page 32. |
|
|
ON SCREEN |
Select the language for the on screen display. |
LANGUAGE |
|
26
Menu |
Item |
Setting |
MONITOR TYPE Select the monitor type to watch a wide screen picture on your monitor.
PICTURE |
|
|
|
|
|
|
|
|
OSD POSITION |
Select the on-screen bar position on the monitor. |
|||||
|
|
• |
1 |
: Higher position |
|
|
|
|
|
• |
2 |
: Lower position (Guidance below the disc setup menu will disappear.) |
|||
|
DIGITAL AUDIO |
Select the signal format to be emitted through the DIGITAL OUT (Optical) terminal. |
|||||
|
OUTPUT |
• |
OFF |
|
: |
Cancels. |
|
|
|
• |
PCM ONLY |
: |
Select for an amplifier or a decoder incompatible |
||
|
|
|
|
|
|
with Dolby Digital, DTS, MPEG Audio, or when |
|
|
|
|
|
|
|
connecting to a recording device. |
|
|
|
• |
DOLBY DIGITAL/PCM |
: |
Select for an amplifier or a decoder compatible |
||
|
|
|
|
|
|
with Dolby Digital. |
|
|
|
• |
STREAM/PCM |
: |
Select for an amplifier or a decoder compatible |
||
|
|
|
|
|
|
with Dolby Digital, DTS, and MPEG Audio. |
|
AUDIO |
DOWN MIX |
When playing back a multi-channel disc, this setting affects the signals reproduced |
|||||
|
through the LINE OUT jacks (and through the DIGITAL OUT terminal when “PCM |
||||||
|
ONLY” is selected for “DIGITAL AUDIO OUTPUT”). |
||||||
|
|
• SURROUND COMPATIBLE : |
Select to enjoy multi-channel surround audio by |
||||
|
|
|
|
|
|
connecting an amplifier compatible with Dolby |
|
|
|
|
|
|
|
Surround. |
|
|
|
• |
STEREO |
|
: |
Normally select this. |
|
|
D. RANGE |
You can enjoy a powerful sound at low or middle volume levels while playing a |
|||||
|
COMPRESSION |
Dolby Digital software. |
|
|
|||
|
|
• |
AUTO |
|
: |
Select to apply the effect to multi-channel |
|
|
|
|
|
|
|
encoded software (excluding 1-channel and |
|
|
|
|
|
|
|
2-channel software). |
|
|
|
• |
ON |
|
: |
Select to always use this function. |
|
|
DivX |
This unit has its own Registration Code. Once you have played back a disc in which |
|||||
|
REGISTRATION |
the Registration Code recorded, this unit’s Registration Code is overwritten for |
|||||
OTHER |
|
copyright protection. |
|
|
|||
FILE TYPE (DISC) |
Select playback file type when a disc contains different types of files. |
||||||
|
|||||||
|
|
• |
AUDIO |
|
: Play MP3/WMA/WAV files. |
||
|
|
• |
VIDEO |
|
: |
Play DivX/MPEG Video files. |
|
|
|
• |
AUDIO + VIDEO |
: |
Play MP3/WMA/WAV/DivX/MPEG Video files. |
ENGLISH
SETTINGS 27
ENGLISH
More about this unit
General
Turning on the power
•By pressing SRC on the unit, you can also turn on the power. If the source is ready, playback starts.
Turning off the power
•If you turn off the power while listening to a disc, disc play will start automatically, next time you turn on the power.
FM/AM
Storing stations in memory
•During SSM search...
–Received stations are preset in No. 1 (lowest frequency) to No. 6 (highest frequency).
–When SSM is over, the station stored in No. 1 will be automatically tuned in.
•When storing stations, the previously preset stations are erased and stations are stored newly.
Disc
General
•In this manual, words “track” and “file” are interchangeably used.
•This unit can only play back audio CD (CD-DA) files if different type of files are recorded in the same disc.
Inserting a disc
•When a disc is inserted upside down, “PLEASE” and “EJECT” appear alternately on the display. Press 0to eject the disc.
Ejecting a disc
•If the ejected disc is not removed within 15 seconds, the disc is automatically inserted again into the loading slot to protect it from dust. Playback starts automatically.
•After ejecting a disc, “NO DISC” appears and you cannot operate some of the buttons. Insert another disc or press SRC to select another playback source.
Playing Recordable/Rewritable discs
•This unit can recognize a total of 5 000 files and 250 folders (a maximum of 999 files per folder).
•This unit can recognize a total 25 characters for file/ folder names.
•Use only “finalized” discs.
•This unit can play back multi-session discs; however, unclosed sessions will be skipped while playing.
•This unit may be unable to play back some discs or files due to their characteristics or recording conditions.
•Rewritable discs may require a longer readout time.
Playing DVD-VR files
•For details about DVD-VR format and playlist, refer to the instructions supplied with the recording equipment.
Playing MP3/WMA/WAV files
•The maximum number of characters for folder and file names is 25 characters; 128 characters for MP3/ WAV and 64 characters for WMA tag information.
•This unit can play back files with the extension code <.mp3>, <.wma>, or <.wav> (regardless of the letter case—upper/lower).
28
•This unit can show the names of albums, artists (performer), and Tag (Version 1.0, 1.1, 2.2, 2.3, or 2.4) for the MP3/WMA/WAV files.
•This unit can display only one-byte characters. No other characters can be correctly displayed.
•This unit can play back files recorded in VBR (variable bit rate).
Files recorded in VBR have a discrepancy in elapsed time indication.
•This unit cannot play back the following files:
–MP3 files encoded with MP3i and MP3 PRO format.
–MP3 files encoded with Layer 1/2.
–WMA files encoded with lossless, professional, and voice format.
–WMA files which are not based upon Windows Media® Audio.
–WMA files copy-protected with DRM.
–Files which have the data such as ATRAC3, etc.
–AAC files and OGG files.
Playing DivX files
•This unit can play back DivX files with the extension code <.divx>, <.div>, <.avi> (regardless of the letter case—upper/lower).
•This unit supports DivX Media Format files, <.divx> or <.avi>.
•This unit can display a unique registration code— DivX Video-on-Demand (VOD—a kind of Digital Rights Management). For activation and more details, visit <www.divx.com/vod>.
•Audio stream should conform to MP3 or Dolby Digital.
•This unit does not support GMC (Global Motion Compression).
•The file encoded in the interlaced scanning mode may not be played back correctly.
•This unit cannot play back the following files:
–Files encoded in Codec (Compressor-decompressor) other than DivX Codec.
•If you want to know more about DivX, visit <http://www.divx.com>.
Playing MPEG Video files
• This unit can play back MPEG Video files with the |
ENGLISH |
|
extension code <.mpg>, <.mpeg>, or <.mod>*. |
||
|
||
* <.mod> is an extension code used for the MPEG-2 files |
|
|
recorded by JVC Everio camcorders. |
|
|
• Audio stream should conform to MPEG1 Audio |
|
|
Layer 2. |
|
|
• This unit cannot playback the following files: |
|
|
– WMV (Windows Media Video) files |
|
|
– RM (Real Media) format files |
|
Changing the source
•If you change the source, playback also stops (without ejecting the disc).
Next time you select “DISC” for the playback source, disc play starts from where it has been stopped previously.
General settings—PSM
•If you change the “AMP GAIN” setting from “HIGH POWER” to “LOW POWER” while the volume level is set higher than “VOLUME 30,” the unit automatically changes the volume level to “VOLUME 30.”
Disc setup menu
•When the language you have selected is not recorded on a disc, the original language is automatically used as the initial language. In addition, for some discs, the initial languages settings will not work as you set due to their internal disc programming.
•When you select “16:9” for a picture whose aspect ratio is 4:3, the picture slightly changes due to the process for converting the picture width.
•Even if “4:3 PAN SCAN” is selected, the screen size may become “4:3 LETTERBOX” for some discs.
Continued on the next page
REFERENCES 29
About sounds reproduced through the rear terminals
ENGLISH |
• Through the analog terminals (Speaker out/LINE OUT): |
|
2-channel signal is emitted. When playing a multi-channel encoded disc, multi-channel signals are |
||
|
||
|
downmixed. DTS sound cannot be reproduced. (AUDIO—DOWN MIX: see page 27.) |
|
|
• Through DIGITAL OUT (optical): |
|
|
Digital signals (Linear PCM, Dolby Digital, DTS, MPEG Audio) are emitted through this terminal. (For more |
|
|
details, see table on page 31.) |
|
|
To reproduce multi-channel sounds such as Dolby Digital, DTS, and MPEG Audio, connect an amplifier or a |
|
|
decoder compatible with these multi-channel sources to this terminal, and set “DIGITAL AUDIO OUTPUT” |
|
|
correctly. (See page 27.) |
On-screen guide icons
During playback, the following guide icons may appear for a while on the monitor.
:Playback
:Pause
:DVD-Video/VCD: Forward slow motion
:DVD-Video: Reverse slow motion
:Forward search
:Reverse search
DVD: The following icons appear at the beginning of a scene containing:
:Multi-subtitle languages
:Multi-audio languages
:Multi-angle views
30