Thank you for purchasing this product.
Before operating this unit, please read the
instructions carefully to ensure the best possible
performance.
In this manual, each model number is described
without the last letter (U/E) which means the
shipping destination.
(U: for USA and Canada, E: for Europe)
Only “U” models (GY-HC550U/GY-HC500U/
GY-HC500SPCU) have been evaluated by UL.
Please read the following before getting started:
For Customer Use:
Model No.
Serial No.
Enter below the Serial No. which is located
on the body.
Retain this information for future reference.
Wireless LAN antenna is not included in GY-HC500U/GY-HC500E/GY-HC500SPCU.
The specifications and appearance of this product are subject to changes for further improvement
without prior notice.
Please check the latest version of the INSTRUCTIONS from the following Mobile User Guide. You can
also download the PDF from the Mobile User Guide.
Mobile User Guide
When you are outside, you can refer to the instructions from your Android phone or iPhone.
http://manual3.jvckenwood.com/pro/mobile/global/
You can view the Mobile User Guide using the browser on your Android phone or iPhone.
IM 1.01
B5A-2966-00
2
1.
Read these instructions.
2.
Keep these instructions.
Important Safety Instructions
4.
5.
6.
7.
8.
These are general Important Safety Instructions and certain items may not
apply to all appliances.
3.
FOR USA
9.
10.
11.
12.
13.
For USA-California Only
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate
Material – special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
.
Introduction
Important Safety Instructions
3
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Pour Californie des États-Unis seulement
Cet appareil contient une pile-bouton CR au lithium qui contient du perchlorate – une
manipulation spéciale peut être requise.
Voir www.dtsc.ca.gov/hazardouswaste/perchlorate
Respecter toutes les instructions.
Ne pas utiliser cet appareil à proximité de l’eau.
Ne nettoyer qu’avec un chiffon sec.
Ne pas boucher les ouvertures de ventilation.
Installer selon les instructions du fabricant.
Ne pas installer à proximité de sources de chaleur telles que des radiateurs,
des accumulateurs de chaleur, des poêles, ou d’autres appareils
(comprenant les amplificateurs) qui produisent de la chaleur.
Protéger le cordon d’alimentation pour éviter qu’il ne soit piétiné ou ne se coince, tout
particulièrement au niveau de la fiche, de la prise de courant et du point où il sort de l’appareil.
Utiliser uniquement des équipements/accessoires spécifiés par le fabricant.
N’utiliser qu’avec le chariot, le stand, le trépied, le support ou
la table spécifié par le fabricant, ou vendu avec l’appareil.
Lorsqu’un chariot est utilisé, faire attention pour déplacer
la combinaison chariot/appareil pour éviter des blessures
causées par un basculement.
Débrancher cet appareil pendant un orage ou quand il
n’est pas utilisé pendant une longue durée.
L’entretien ou la réparation de l’appareil doit être effectué par du personnel qualifié uniquement.
Un dépannage est nécessaire lorsque l’appareil a été endommagé d’une façon ou d’une autre,
telle que lorsque le cordon d’alimentation ou la fiche est endommagé, si du liquide a été renversé
ou si des objets sont tombés à l’intérieur de l’appareil, si l’appareil a été exposé à la pluie ou
à l’humidité, ne fonctionne pas normalement ou a fait une chute.
1.
Lire ces instructions.
2.
Conserver ces instructions.
CONSIGNES DE SÉCURITÉ IMPORTANTES
Ces informations sont des CONSIGNES DE SÉCURITÉ IMPORTANTES et
certains points peuvent ne pas s’appliquer à tous les appareils.
3.
POUR LES ÉTATS-UNIS
Tenir compte de tous les avertissements.
Introduction
.
Important Safety Instructions
4
Safety Precautions
CAUTION
FOR USA AND CANADA
CAUTION:
TO REDUCE THE RISK OF
ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR
BACK).
NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
The lightning flash with
arrowhead symbol, within
an equilateral triangle is
intended to alert the user to
the presence of uninsulated
“dangerous voltage” within
the product’s enclosure that
may be of sufficient
magnitude to constitute a
risk of electric shock to
persons.
The exclamation point within
an equilateral triangle is
intended to alert the user to
the presence of important
operating and maintenance
(servicing) instructions in
the literature accompanying
the appliance.
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
POUR CANADA
RISQUE
D’ELECTROCUTION
NE PAS OUVRIR
ATTENTION:
POUR EVITER TOUT RISQUE
D’ELECTROCUTION NE PAS
OUVRIR LE BOITER. AUCUNE
PIECE INTERIEURE N’EST A
REGLER PAR L’UTILISATEUR. SE
REFERER A UN AGENT QUALIFIE
EN CAS DE PROBLEME.
ATTENTION
Le symbole de l’éclair à
l’intérieur d’un triangle
équilatéral est destiné à
alerter l’utilisateur sur la
présence d’une “tension
dangereuse” non isolée dans
le boîtier du produit. Cette
tension est suffisante pour
provoquer l’électrocution de
personnes.
Le point d’exclamation à
l’intérieur d’un triangle
équilatéral est destiné à
alerter l’utilisateur sur la
présence d’opérations
d’entretien importantes au
sujet desquelles des
renseignements se trouvent
dans le manuel
d’instructions.
Ces symboles ne sont
utilisés qu’aux Etats-Unis.
.
Introduction
.
Safety Precautions
5
Model Number:
Trade Name:
Responsible
party:
Address:
Telephone
Number:
Supplier's Declaration of Conformity
GY-HC550U
GY-HC500U
GY-HC500SPCU
JVC
JVCKENWOOD USA
Corporation
500 Valley Road,
Suite 203 Wayne,
NJ 07470
973-317-5000
This device complies with Part 15 of
the FCC Rules. Operation is subject to
the following two conditions: (1) This
device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
Changes or modifications not
approved by JVC could void the
user’s authority to operate the
equipment. This equipment has been
tested and found to comply with the
limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference when the equipment is
operated in a commercial
environment.
This equipment generates, uses, and
can radiate radio frequency energy
and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications. Operation of this
equipment in a residential area is
likely to cause harmful interference in
which case the user will be required
to correct the interference at his own
expense.
Numéro de
modèle :
Nom de marque :
Personne
responsable :
Adresse :
Numéro de
téléphone :
Déclaration de conformité du fournisseur
GY-HC550U
GY-HC500U
GY-HC500SPCU
JVC
JVCKENWOOD USA
Corporation
500 Valley Road,
Suite 203 Wayne,
NJ 07470
973-317-5000
Cet ensemble se conforme à la partie 15 des
règles de la FCC (Federal Communications
Commission). Le fonctionnement est sujet aux
deux conditions suivantes : (1) Cet appareil ne
peut pas causer d’interférences nuisibles, et
(2) cet appareil doit accepter toute interférence
reçue, comprenant des interférences qui
peuvent causer un mauvais fonctionnement.
Des changements ou modifications
non approuvés par JVC peuvent
annuler le droit de l’utilisateur de faire
fonctionner l’appareil. Cet appareil a
été testé et il a été reconnu qu’il se
conforme aux limites concernant
l’appareillage informatique de classe
A correspondant à la partie 15 des
règles de la FCC. Ces limites sont
conçues pour fournir une protection
raisonnable contre les interférences
dangereuses lorsque l’équipement est
utilisé dans un environnement
commercial.
Cet appareil génère, utilise et peut
émettre de l’énergie des fréquences
radio et, s’il n’est pas installé et utilisé
selon les instructions du fabricant,
peut causer des interférences
nuisibles en communications radio.
L’utilisation de cet équipement dans
une zone résidentielle est susceptible
de causer des interférences néfastes,
auquel cas l’utilisateur devra prendre
des mesures à ses propres frais.
Introduction
.
.
6
Safety Precautions
.
.
.
CAUTION:
The mains plug shall remain readily
operable.
Remove the mains plug immediately if
the camera functions abnormally.
WARNING:
The battery pack, the camera with
battery installed, and the remote control
with battery installed should not be
exposed to excessive heat such as direct
sunlight, fire or the like.
WARNING: TO PREVENT FIRE OR
SHOCK HAZARD, DO NOT
EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
NOTES:
The rating plate and safety caution are
on the bottom and/or the back of the
main unit.
The serial number plate is on the
bottom of the unit.
The rating information and safety
caution of the AC adapter are on its
upper and lower sides.
Caution on Replaceable lithium
battery
The battery used in this device may
present a fire or chemical burn hazard if
mistreated.
Do not recharge, disassemble, heat
above 100°C (212°F) or incinerate.
Replace battery with Panasonic, Sanyo,
Sony or Maxell CR2025.
Danger of explosion or risk of fire if the
battery is incorrectly replaced.
Dispose of used battery promptly.
Keep away from children.
Do not disassemble and do not dispose
of in fire.
Attention:
La prise secteur doit être opérationnelle.
Débranchez immédiatement la fiche
secteur si le caméscope ne fonctionne
pas normalement.
Avertissement:
Évitez d’exposer la batterie, le
caméscope avec la batterie insérée ou la
télécommande avec la batterie insérée à
une chaleur excessive, telle que celle
des rayons directs du soleil, d’un feu ou
de tout autre source de chaleur.
AVERTISSEMENT : POUR EVITER
LES RISQUES D’INCENDIE OU
D’ELECTROCUTION, NE PAS
EXPOSER L’APPAREIL A LA
PLUIE NI A L’HUMIDITE.
REMARQUES :
La plaque d’identification et
l’avertissement de sécurité se trouvent
sous l’appareil et/ou au dos.
La plaque du numéro de série est
située sur la partie inférieure de
l’appareil.
Les informations d’identification et
l’avertissement de sécurité de
l’adaptateur secteur sont situés sur ses
côtés supérieur et inférieur.
Avertissement sur la pile au
lithium remplaçable
La pile utilisée dans cet appareil peut
présenter des risques d’incendie ou de
brûlure chimique si elle est mal traitée.
Ne pas recharger, démonter, chauffer à
plus de 100°C (212°F) ni mettre au feu.
Remplacez la pile avec Panasonic,
Sanyo, Sony ou Maxell CR2025.
Danger d’explosion ou risque d’incendie
si la pile n’est pas changée correctement.
Jeter immédiatement les piles usées.
Placer hors de la portée des enfants.
Ne pas démonter ni jeter au feu.
.
Introduction
.
.
.
.
.
.
.
.
Safety Precautions
7
When the equipment is installed in a
cabinet or on a shelf, make sure that it
has sufficient space on all sides to allow
for ventilation (10 cm (3-15/16") or more
on both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a
newspaper, or cloth etc. the heat may not
be able to get out.)
No naked flame sources, such as lighted
candles, should be placed on the
apparatus.
When discarding batteries,
environmental problems must be
considered and the local rules or laws
governing the disposal of these batteries
must be followed strictly.
The apparatus shall not be exposed to
dripping or splashing and that no objects
filled with liquids, such as vases, shall be
placed on the apparatus.
Do not point the lens directly into the
sun. This can cause eye injuries, as well
as lead to the malfunctioning of internal
circuitry. There is also a risk of fire or
electric shock.
CAUTION!
The following notes concern possible
physical damage to this unit and to the
user.
Carrying or holding this unit by the LCD
monitor can result in dropping the unit,
or in a malfunction.
Do not use a tripod on unsteady or
unlevel surfaces. It could tip over,
causing serious damage to the unit.
CAUTION!
Connecting cables (Audio/Video, etc.) to
this unit and leaving it on top of the TV is
not recommended, as tripping on the
cables will cause the unit to fall, resulting
in damage.
Si le matériel est installé dans un coffret
ou sur une étagère, s’assurer qu’il y a un
espace suffisant sur tous les côtés pour
permettre la ventilation (10 cm (3-15/16")
ou plus sur les deux côtés, au dessus et
à l’arrière).
Ne pas boucher les orifices de
ventilation.
(Si les orifices de ventilation sont
bouchés par un journal, un tissu, etc., la
chaleur peut ne pas s’éliminer.)
Aucune source à flamme nue, telle que
des bougies allumées, ne doit être
placée sur l’appareil.
En jetant des batteries aux ordures, les
problèmes d’environnement doivent être
pris en considération et les
réglementations locales ou la législation
concernant le rebut de ces batteries
doivent être strictement respectées.
L’appareil ne doit pas être exposé à de
l’eau ou à des éclaboussures et les
objets remplis de liquide, tels que des
vases, ne doivent pas être placés sur
l’appareil.
Ne dirigez pas l’objectif directement vers
le soleil. Vous pourriez vous abîmer la
vue et l’appareil pourrait être
endommagé. Il y a aussi risque
d’incendie ou d’électrocution.
Attention!
Les remarques suivantes sont destinées
à protéger l’utilisateur et le caméscope
contre des dommages éventuels.
Ne pas transporter ou saisir le
caméscope par l’écran LCD, car il
pourrait tomber ou s’endommager.
Ne pas utiliser de trépied
photographique sur des surfaces
irrégulières et inclinées. Il pourrait
tomber et le caméscope pourrait être
sérieusement endommagé.
Attention!
Avec des câbles (Audio/Vidéo, etc.)
raccordés, il est recommandé de ne pas
laisser le caméscope sur le dessus du
téléviseur, car tirer sur les câbles
pourrait faire tomber le caméscope,
causant des dommages.
Introduction
.
.
.
Safety Precautions
8
.
.
.
GY-HC550U
Radio Frequency Energy Safety Information
Warning
This JVC camera generates RF EME while
transmitting. RF
& Magnetic Energy) has the potential to cause
slight thermal, or heating effects to any part of
your body less than the recommended distance
from this radio transmitter’s antenna. RF energy
exposure is determined primarily by the distance
to and the power of the transmitting device. In
general, RF exposure is minimized when the
lowest possible power is used or transmission
time is kept to the minimum required for
consistent communications, and the greatest
distance possible from the antenna to the body
is maintained.
The following list provides you with the information
required to ensure that you are aware of RF
exposure.
0
While transmitting, always keep the antenna
and the radio at least 5 cm (1-31/32”) from your
body or face, as well as from any bystanders.
0
To maintain compliance with FCC's RF
exposure guidelines, use only the supplied
antenna (with antenna holder).
Unauthrized antenna, modification, or
attachments could damage the transmitter and
may violate FCC regulations.
Electromagnetic Interference Compatibility
Electronic devices are susceptible to
electromagnetic interference (EMI) if they are not
adequately shielded or designed for
electromagnetic compatibility.
Because this product generates RF energy, it can
cause interference to such equipment.
0
Turn OFF
do so. Hospitals and health care facilities use
equipment that is sensitive to electromagnetic
radiation.
0
Turn OFF your product while on board an aircraft
when so instructed. Use of the product must be
in accordance with airline regulations and/or
crew instructions.
EME (Radio Frequency Electric
your WLAN where signs are posted to
Informations sur la sécurité en présence
d'énergie par radiofréquences
Avertissement
caméscope
Ce
de la transmission. L'EME par RF (énergie
électrique et magnétique par radiofréquences)
peut causer de légers effets thermiques ou
chauffants sur toute partie de votre corps,
lorsque vous trouvez à une distance inférieure à
celle recommandée de l’antenne de cet émetteur
radio. L'exposition à l'énergie par
radiofréquences est principalement déterminée
par la distance et la puissance de l'appareil
émetteur. En général, l'exposition aux
radiofréquences est minimisée lorsqu'on utilise
la puissance la plus faible possible ou que le
temps de transmission est maintenu au minimum
requis pour assurer des communications
cohérentes et lorsqu'on maintient la plus grande
distance possible entre l'antenne et le corps.
La liste suivante vous fournit les informations dont
vous avez besoin pour être sûr d'être informé de
l'exposition aux radiofréquences.
0
Pendant la transmission, gardez toujours
l’antenne et
de votre corps ou de votre visage, ainsi que de
toutes les personnes aux alentours.
0
Pour maintenir la conformité avec les directives
d’exposition RF de la FCC, utilisez uniquement
l’antenne fournie (avec support d'antenne).
Une antenne, une modification ou des
accessoires non autorisés peuvent
endommager le transmetteur et enfreindre les
réglementations de la FCC.
Compatibilité aux interférences
électromagnétiques
Les appareils électroniques sont sensibles aux
interférences électromagnétiques (EMI) s'ils ne
sont pas correctement protégés ou conçus pour
une compatibilité électromagnétique.
Étant donné que cet appareil génère de l’énergie
par radiofréquences, il peut provoquer des
interférences avec ce genre d’équipement.
0
Éteignez votre WLAN lorsque des signes vous
l'indiquant s'affichent. Les hôpitaux et les
établissements de santé utilisent un
équipement sensible aux rayonnements
électromagnétiques.
0
Éteignez votre appareil lorsque vous trouvez à
bord d’un avion et qu'on vous le demande.
L'utilisation de l'appareil doit être conforme aux
règlements de
instructions de l'équipage.
JVC génère de l'EME par RF lors
la radio à au moins 5 cm (1-31/32”)
la compagnie aérienne et/ou aux
Introduction
Safety Precautions
9
GY-HC550U
For indoor use only (5150-5250 MHz) in
Canada
There are legal restrictions on the use and
outdoor use depending on the country and
region. Please be careful not to violate the law.
Introduction
Pour usage intérieur seulement (5150-5250
MHz) au Canada
Il existe des restrictions légales concernant
l’utilisation générale et extérieure en fonction du
pays et de la région. Veillez à respecter la loi.
Data transmission is always intiated by software,
which is the passed down through the MAC,
through the digital and analog baseband, and
finally to the RF chip. Several special packets are
initiated by the MAC.These are the only ways the
digital baseband portion will turn on the RF
transmitter, which it then turns off at the end of
the packet. Therefore, the transmitter will be on
only while one of the aforementioned packets is
being transmitted.In other words, this device
automatically discontinue transmission in case
of either absence of information to transmit or
operational failure.
Frequency Tolerance: 20 ppm
This radio transmitter (6549A-W8997M1216)
has been approved by Innovation, Science and
Economic Development
the antenna types listed bellow, with the
maximum permissible gain indicated.
Antenna types not included in this list that have
a gain greater than the maximum gain indicated
for any type listed are strictly prohibited use with
this device.
Antenna
type
Dipole
3.6 dBi (4.9-5.8 GHz)
1.9 dBi (2.4-2.5 GHz)
Canada to operate with
GainImpedance
50 Ω
La transmission des données est toujours initiée
par le logiciel, puis les données sont transmises
par l'intermédiaire du MAC, par la bande de base
numérique et analogique et, enfin à la puce RF.
Plusieurs paquets spéciaux sont initiés par le
MAC. Ce sont les seuls moyens pour qu'une de
la bande de base numérique active l'émetteur
RF, puis désactive celui-ci à la fin du paquet. En
conséquence, l'émetteur reste uniquement
activé lors de la transmission d'un des paquets
susmentionnés. En d'autres termes, ce dispositif
interrompt automatiquement toute transmission
en cas d'absence d'informations à transmettre
ou de défaillance.
Tolérance de fréquence: 20 ppm
Le présent émetteur radio (6549 A-W 8997 M
1216) a été approuvé par Innovation, Sciences
et Développement économique Canada pour
fonctionner avec les types d'antenne énumérés
ci-dessous et
Les types d'antenne non inclus dans cette liste,
et dont le gain est supérieur au gain maximal
indiqué pour tout type figurant sur la liste, sont
strictement interdits pour l'exploitation de
l'émetteur.
Types
d'antenne
Dipôle
ayant un gain admissible maximal.
Gainl'impédance
3.6 dBi (4.9-5.8 GHz)
1.9 dBi (2.4-2.5 GHz)
50 Ω
Safety Precautions
10
GY-HC550U
This transmitter must not be co-located or
operated in conjunction with any other antenna
or transmitter.
Cet émetteur ne doit pas être co-localisé ou
utilisé en
un autre émetteur.
conjonction avec une autre antenne ou
This device contains licence-exempt
transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two
conditions:
A
This device may not cause interference.
B
This device must accept any interference,
including interference that may cause
undesired operation of the device.
The available scientific evidence does not show
that any health problems are associated with
using low power wireless devices. There is no
proof, however, that these low power wireless
devices are
devices emit low levels of radio frequency energy
(RF) in the microwave range while being used.
Whereas high levels of RF can produce health
effects (by heating tissue), exposure of low-level
RF that does not produce heating effects causes
no known adverse health effects. Many studies
of low-level RF exposures have not found any
biological effects. Some studies have suggested
that some biological effects might occur, but
such findings have not been confirmed by
additional research.
The RF module, W8997-M1216 has been tested
and found to comply with FCC/ISED radiation
exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency
(RF) Exposure Guidelines and RSS-102 of the
ISED radio frequency (RF) Exposure rules.
absolutely safe. Low power Wireless
L’émetteur/récepteur exempt de licence contenu
dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement
économique Canada applicables aux appareils
radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes :
A
L’appareil ne doit pas produire de brouillage;
B
L’appareil doit accepter tout brouillage
radioélectrique subi,
susceptible d’en compromettre le
fonctionnement.
Les connaissances scientifiques dont nous
disposons n’ont mis en évidence aucun
problème de santé associé à l’usage des
appareils sans fil à faible puissance. Nous ne
sommes cependant pas en mesure de prouver
appareils sans fil à faible puissance sont
que ces
entièrement sans danger. Les appareils sans fil
à faible puissance émettent une énergie
fréquence radioélectrique (RF) très faible dans
le spectre des micro-ondes lorsqu’ils sont
utilisés. Alors qu’une dose élevée de RF peut
avoir des effets sur la santé (en chauffant les
tissus), l’exposition à de faibles RF qui ne
produisent pas de chaleur n’a pas de mauvais
effets connus sur la santé. De nombreuses
études ont été menées sur les expositions aux
RF faibles et n’ont découvert aucun effet
biologique. Certaines études ont suggéré qu’il
pouvait y avoir certains effets biologiques, mais
ces résultats n’ont pas été confirmés par des
recherches supplémentaires.
Le module RF, W8997-M1216 a été testé et jugé
conforme aux limites d’exposition aux
rayonnements énoncées pour un
environnement non contrôlé et respecte les
règles les radioélectriques (RF) de la FCC lignes
directrices d'exposition et d’exposition aux
fréquences radioélectriques (RF) CNR-102 de l’
ISDE.
même si le brouillage est
Introduction
Safety Precautions
11
IMPORTANT (for owners in the U.K.)
Connection to the mains supply in
the United Kingdom.
DO NOT cut off the mains plug from
this equipment.
If the plug fitted is not suitable for the
power points in your home or the cable is
too short to reach a power point, then
obtain an appropriate safety approved
extension lead or contact the local
dealers in your area.
BE SURE to replace the fuse only with
an identical approved type, as originally
fitted, and to replace the fuse cover.
If nonetheless the mains plug is cut off
be sure to remove the fuse and dispose
of the plug immediately, to avoid possible
shock hazard by inadvertent connection
to the mains supply.
If this product is not supplied fitted with a
mains plug then follow the instructions
given below:
DO NOT make any connection to the
Larger Terminal coded E or Green.
The wires in the mains lead are coloured
in accordance with the following code:
If these colours do not correspond with
the terminal identifications of your plug,
connect as follows:
Blue wire to terminal coded N (Neutral)
or coloured black.
Brown wire to terminal coded L (Live) or
coloured Red.
If in doubt — consult a competent
electrician.
CAUTIONS:
To prevent shock, do not open the cabinet.
No user serviceable parts inside.
Refer servicing to qualified personnel.
Blue to N
(Neutral) or Black
Brown to L (Live)
or Red
WARNING
Operation of this equipment in a
residential environment could cause
radio interference.
CAUTION:
Where there are strong electromagnetic
waves or magnetism, for example near a
radio or TV transmitter, transformer,
motor, etc., the picture and the sound
may be disturbed. In such case, please
keep the apparatus away from the
sources of the disturbance.
The plastics packaging bags may cause
suffocation when they are covered over the
head. Tear them open, and keep them away
from the reach of infants and children by
ensuring that they are disposed of properly.
Wireless LAN
This device is a 2.4 GHz wideband
transmission system (transceiver),
intended for use in all EU member
states and EFTA countries, except in
France and Italy where restrictive use
applies.
In Italy the end-user should apply for a
license at the national spectrum
authorities in order to obtain
authorization to use the device for
setting up outdoor radio links and/or for
supplying public access to
telecommunications and/or network
services.
This device may not be used for setting
up outdoor radio links in France and in
some areas the RF output power may
be limited to 10 mW EIRP in the
frequency range of 2454 - 2483.5 MHz.
For detailed information the end-user
should contact the national spectrum
authority in France.
Frequency Range
Output Power
2.4GHz Band : 1 - 13ch
11 b/g/n : 14 dBm
(max)
Frequency Range
Output Power
5GHz Band : W52/W53/W56
11 n/a/ac : 11 dBm (max)
Introduction
.
.
Safety Precautions
12
.
.
GY-HC550E
.
.
.
GY-HC550E and GY-HC500E
The European representative of
JVCKENWOOD Corporation is:
Die europäische Vertretung für die
JVCKENWOOD Corporation ist:
JVCKENWOOD Deutschland GmbH
Konrad-Adenauer-Allee 1-11
61118 Bad Vilbel
GERMANY
Dear customer,
this apparatus is in compliance with the
valid European Directive and the
relevant standards regarding
electromagnetic compatibility.
Sehr geehrter Kunde, sehr geehrte
Kundin,
dieses Gerät stimmt mit der gültigen
europäischen Richtlinie und den
relevanten Normen bezüglich
elektromagnetischer Verträglichkeit
überein.
Hereby, JVCKENWOOD Corporation
declares that the radio equipment type
GY-HC550E is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of
conformity is available at the following
internet address:
Hiermit erklärt die , JVCKENWOOD
Corporation, dass der Funkanlagentyp
GY-HC550E der Richtlinie 2014/53/EU
entspricht.
Der vollständige Text der
EU-Konformitätserklärung ist unter der
folgenden Internetadresse verfügbar:
http://www3.jvckenwood.com/ecdoc/
Battery Pack
The supplied battery pack is a lithium-ion
battery. Before using the supplied battery
pack or an optional battery pack, be sure
to read the following cautions:
To avoid hazards
... do not burn.
When transporting, carry the battery in
a plastic bag.
... do not modify or disassemble.
... do not expose the battery to
temperatures exceeding 60°C (140°F),
as this may cause the battery to
overheat, explode or catch fire.
... use only specified chargers.
To prevent damage and prolong
service life
... do not subject to unnecessary shock.
... charge within the temperature range
of 10°C to 35°C (50°F to 95°F). Cooler
temperatures require longer charging
time, or in some cases stop charging
at all. Warmer temperatures prevent
complete charging, or in some cases
stop charging at all.
... store in a cool, dry place. Extended
exposure to high temperatures will
increase natural discharge and
shorten service life.
... keep a 30% battery level if the
battery pack is not to be used for a
long period of time.
... remove from charger or powered unit
when not in use, as some machines
use current even when switched off.
... do not drop or subject to strong
impact.
... do not short-circuit the
terminals. Keep it away
from metallic objects
when not in use.
Terminals
.
GY-HC500E
.
GY-HC550E
.
Introduction
.
Safety Precautions
13
Para Brasil
Informação sobre eliminação de
baterias
Este produto não deverá ser eliminado
como lixo doméstico em geral.
Devolva a bateria velha ao comerciante
ou para a rede autorizada, para que seja
devolvida ao fabricante ou importador.
A reciclagem e eliminação de lixo em
uma maneira adequada, ajudarão para
preservar recursos, prevenindo, ao
mesmo tempo, contra efeitos prejudiciais
sobre a nossa saúde e o meio ambiente.
Important Notice concerning the Software ..... 249
.
Introduction
Contents
17
Main Features
1" CMOS sensor and new 4K 20x lens
for high-quality recording
Introduction
Comes with a 1" CMOS sensor that delivers high
resolution and an excellent S/N ratio. At the same
time, a new 4K 20x lens with a good balance in
viewing angle, image quality and magnification is
employed to
thereby achieving premium-quality 4K recording
with high sensitivity and low noise.
“Apple ProRes 422” available as a
standard feature to achieve highresolution and high bit-rate recording
performance
By making use of the KA-MC100 SSD media
adapter (sold separately), it is possible to perform
4K 50p/60p
speed SSD memory.
A variety of wired and wireless
interfaces to support various network
connections
In addition to the USB host terminal for wireless
LAN and LTE USB adapter connections, this
camera recorder is equipped with a variety of
interfaces such as wired LAN terminal and built-in
wireless LAN
antennas A to support various network
connections.
reduce the occurrence of aberrations,
Apple ProRes 422 recording to a high-
with 2.4GHz/5GHz MIMO dual band
HDR and log gamma for high dynamic
range and wide color gamut
This camera recorder is equipped with HLG
(Hybrid Log-Gamma) that conforms to ITU-BT.
2100 and our in-house J-Log1 Gamma with 800%
dynamic range to cope with HDR (High Dynamic
Range). Capable of recording in 10-bit for high
dynamic range and wide color gamut.
High-frame-rate recording in Full HD
quality (1920x1080)
Videos with a maximum frame rate of 120 fps can
be recorded
the style of the subject in fast-moving sports and in
video expression that leaves a deep impression.
in slow motion. It can be used to check
Broadcast Overlay A L
Station name, program name, or news title
according to the recorded content can be entered
easily by using a smartphone or tablet, and this
information can
clip or streaming images.
Also, it comes with a full-screen graphic feature that
allows overlay of the entire screen with images
such as notifications and advertisements.
be superimposed on the recording
Score Board Overlay L
Allows display of scores for games such as football,
baseball, basketball and hockey over the video
image.
Scores can
while video-shooting is in progress, enabling easy
operation such as live broadcast by a small crew.
be entered from a smartphone or tablet
Bidirectional live streaming feature
Enables live streaming broadcast from the camera,
while at the same time receives program images
from studio stations as IP return video or intercom
audio as IP return audio (IFB) over the same line.
High
quality
signal processing by 10-bit,
4:2:2 sampling
High quality signal processing that delivers rich
gradation expression and color reproduction of
video signals is possible by means of 10-bit, 4:2:2
sampling.
Various
Recording codecs supported are MPEG-4 AVC/H.
264 and Apple ProRes 422, which is compatible
with 4:2:2 10-bit recording. Selectable ProRes
formats include Apple ProRes 422HQ, Apple
ProRes 422 and Apple ProRes 422LT. Selectable
MPEG-4 AVC/H.264 formats include QuickTime
(MOV) and MP4.
It is also compatible with MPEG2 MXF, which is a
widely-used format at broadcasting stations. A
18
usage-based recording formats
Main Features
Auto focus/optical image stabilizer
(OIS)
The camera recorder is equipped with a face
detection auto
screen. Switching to manual focus is also possible.
A built-in optical image stabilizer feature is also
available.
focus function that covers the entire
Prevents camera shake with the OIS
hard lock feature
Helps to secure the OIS lens to prevent unnatural
video images due to sudden acceleration of
vehicles when
the camera is mounted on a vehicle.
Double SD card slots for series/dual
recordings
The most common SDHC/SDXC card recording
system is used for the memory card. This ensures
high reliability and operation at low running cost.
Various user friendly recording options are
available. These include series recording which
enables seamless long hour continuous
recordings over
same file to two slots.
the slots and dual recording of the
FTP feature that supports automatic
upload
Clips stored in the recording media can be
uploaded automatically to the FTP server while
recording is paused. When recording is in
progress, clips
recording can also be uploaded.
stored in the slot that is not used for
Large tricolor LED indicators that show
the camera and network status
The two large LED indicators light up in three
different colors
status and network status (including the return
video) at a glance.
to allow identification of the camera
Time code input/output terminals for
shooting using multiple cameras
This camera recorder supports the use of multiple
cameras as well as studio use.
Professional-style switch layout and
diverse video parameters
Switches for Gain and White Balance are available
on the side panel to enable quick switching
according to the shooting scene. Image quality
parameters such as gamma and color matrix are
also available in the menu for adjustment to the
preferred tones.
Built-in GPS A L
This camera recorder is built in with GPS function,
which enables the positional information obtained
from the GPS satellite during a shoot to be
recorded as metadata.
* Note that acquisition of the positional
information may fail depending on the weather
condition.
User buttons/switches assignable with
different functions for greater ease of
use
Menu items corresponding to each user button are
available to assign the buttons with different
functions.
Symbols used
Caution : Describes precautions concerning the
Memo: Describes reference information, such
A
A
B
L
Content of this manual
0
All rights reserved by JVCKENWOOD
Corporation. Unauthorized duplication or
reprinting of this manual, in whole or in part, is
strictly prohibited.
0
Illustrated designs, specifications and other
contents of this manual are subject to change for
improvement without prior notice.
0
SDXC and SDHC logos are trademarks of
SD-3C, LLC.
0
The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI
Licensing Administrator, Inc. in the United States
and other countries.
0
QuickTime, Final Cut Pro, iPhone, iPad, iPod
touch, macOS and Safari are trademarks of
Apple Inc., registered in the U.S. and other
countries.
0
iOS is a trademark or registered trademark of
Cisco in the U.S. and other countries and is used
under license.
0
Android and Google Chrome are trademarks
and/or registered trademarks of Google LLC.
0
QR Code is a registered trademark of Denso
Wave Incorporated.
0
Microsoft, Windows, and Internet Explorer are
either registered trademarks or trademarks of
Microsoft Corporation in the United States
and/or other countries.
0
The company name of Fontworks, Fontworks,
and the name of the fonts are registered
trademarks of Fontworks Inc.
0
Zixi and the Zixi logo are trademarks of Zixi LLC.
0
Other product and company names included in
this instruction manual are trademarks and/or
registered trademarks of their respective
companies. Marks such as ™ and ® have been
omitted in this manual.
operation of this product.
as functions and usage restrictions of
this product.
: Indicates the reference page numbers
and reference items.
: Feature available on GY-HC550U/
GY-HC550E only.
: Feature available on GY-HC500U/
GY-HC500E/GY-HC500SPCU only.
: Feature available on GY-HC500SPCU
only.
Introduction
Main Features
19
Precautions for Proper
Use
Power Saving
o
When this unit is not in use, be sure to set the
[POWER ON/OFF] switch to “OFF
reduce power consumption.
” in order to
Storage and Usage Locations
Introduction
o
Allowable ambient temperature and humidity
Be sure to use this unit within the allowable
temperature range of 0 °C to 40 °C (32 °F to
104°F) and a relative humidity of 30 % to 80 %.
Using this unit at a temperature or humidity
outside the allowable ranges could result not
only in malfunction but also serious impact on
the CMOS elements as small white spots may
be generated.
o
Strong electromagnetic waves or magnetism
Noise may appear in the picture or audio and/or
the colors may be incorrect if this unit is used
near a radio or television transmitting antenna,
in places where strong magnetic fields are
generated by transformers, motors, etc., or near
devices emitting radio waves, such as
transceivers or cellular phones.
o
Use of wireless microphone near this unit
When a wireless microphone or wireless
microphone tuner is used near this unit during
recording, the tuner could pick up noise.
o
Avoid using or placing this unit in the following
places.
0
Places subject to extreme heat or cold
0
Places with excessive dirt or dust
0
Places with high humidity or moisture
0
Places subject
a cooking stove
0
Places subject to strong vibrations or unstable
surfaces
0
In a parked car under direct sunlight or near a
heater for long hours
o
Do not place this unit at places that are subject
to radiation or X-rays, or where corrosive gases
occur.
o
Protect this unit from being splashed with water.
(Especially when shooting in the rain)
o
Protect this unit from getting wet when shooting
on a beach. In addition, salt and sand may
adhere to the body. Be sure to clean the unit after
use.
o
Protect this unit against penetration of dust
when using it in a place subject to sandy dust.
Please exercise care during use.
to smoke or vapor such as near
Maintenance
o
Turn off the power before performing any
maintenance.
o
Wipe the external cabinet of the unit with a soft
cloth. Do not wipe the body with benzene or
thinner. Doing
or turn cloudy. When it is extremely dirty, soak
the cloth in a solution of neutral detergent, wipe
the body with it, and then use a clean cloth to
remove the detergent.
so may cause the surface to melt
Rechargeable Battery
o
Be sure to use only the specified batteries.
We do not guarantee the safety and
performance of this device if an unspecified
battery is used.
o
Store the battery in a cool and dry place when
not in use. Do not expose the battery to high
temperatures (such as in a car under direct
sunlight). Failure to do so not only shortens the
battery life but also damages the battery.
o
Charge the battery first before using.
o
If you are not using the battery for a prolonged
period of
30 % to 40 % charge level to prevent
deterioration.
o
Recharge the battery to a level of 10 % to 20 %
once every
Storing the battery at a fully discharged state will
result in over discharging and inability to charge
the battery.
o
ATTENTION:
time, remove and keep the battery at a
six months when storing the battery.
The product you have purchased
is powered by a rechargeable
battery that is recyclable.
Please call 1-800-8-BATTERY for
information on how to recycle this
battery.
Carrying the Camera
o
not
drop or hit this unit against a hard object
Do
when transporting.
Precautions for Proper Use
20
Regular Inspection (Maintenance)
Groove
o
Under normal environment, dust will
accumulate on the camera recorder when it is
used over a long period. Dust may enter the
camera recorder
This may affect the image and sound quality of
the camera recorder. Check and replace the fan
after every 9000 hours (suggested guideline).
You can check the usage time of the fan in
[System] B [System Information] B [Fan Hour].
(A P149 [ Fan Hour ] )
If the fan is used for more than 9000 hours
without replacement, “Fan Maintenance
Required” will be displayed every time you turn
on the power.
especially if it is used outdoors.
SDHC/SDXC Cards
o
SDHC/SDXC card
“recording media” in this manual.
o
This camera recorder saves the recorded
images and audio sound on the SD card (sold
separately) in the card slot.
o
If the SD card contains files recorded by devices
other than this camera recorder or files that are
saved from a PC, the recordable time may be
shorter or data may not be properly recorded. In
addition, the remaining space on the card may
not increase even when files are deleted using
a PC.
o
For details on the combinations of usable SD
card and format setting, refer to the following.
(A P48 [Format Setting and Usable SD Card
Combinations] )
* Using cards other than those from Panasonic,
TOSHIBA or SanDisk may result in recording
failure or data loss.
is referred to as “SD card” or
Handling of SD Cards
o
The status indicator lights up in red when data
on the SD card is being accessed.
Do not remove the SD card during data access
(such as
not turn off the power or remove the battery and
AC adapter during access either.
o
Do not use or store the SD card in a place that
is subject to static electricity or electrical noise.
o
Do not place the SD card near locations that are
exposed to strong magnetic fields or radio
waves.
o
Inserting the SD card incorrectly may result in
damage of this unit or the SD card.
o
We are not liable for any accidental loss of data
stored on the SD card. Please back up any
important data.
recording, playback, or formatting). Do
o
Make use of the SD card within the prescribed
conditions of use.
Do not use it at the following locations.
Places that are subject to direct sunlight, high
humidity or corrosion, places near thermal
equipment, sandy or dusty places, or in a car
under the sun with the doors and windows
closed.
o
o
o
o
o
o
o
o
o
o
o
o
bend or drop the SD card, or subject it to
Do not
strong impact or vibration.
Do not splash the SD card with water.
Do not dismantle or modify the SD card.
Do not touch the terminals with your hands or
with a metal object.
Do not allow dust, dirt, water, or foreign objects
to adhere to the terminals.
Do not remove the labels or stick other labels or
stickers on the SD cards.
Do not use pencils or ballpoint pens to write on
the SD cards. Always use oil-based pens.
If you format (initialize) the SD card, all data
recorded on the card, including video data and
setup files, will be deleted.
You are recommended to use cards that are
formatted (initialized) on this camera recorder.
0
The SD card may be damaged if the camera
recorder is not operated correctly. Formatting
(Initializing) the SD card may allow it to
operate correctly.
0
SD cards that have been formatted
(initialized) on other cameras, computers or
peripheral equipment may not operate
correctly. In this case, format (initialize) the SD
card on this camera recorder.
If you want to wipe out all information by
completely erasing the data, we recommend
either using commercially available software
that is specially designed for that purpose, or by
physically destroying the SD card with a
hammer, etc. When formatting or erasing data
using the camera recorder, only the file
administration information is changed. The data
is not completely erased from the SD card.
Some commercially available SD cards may be
harder to be removed from this unit. Remove
them by hooking onto the groove on the cards.
0
It will be easier to remove the cards after
several times.
0
Do not stick any stickers on the cards.
The SD card may pop out when it is being
removed. Be careful not to lose the card.
.
Introduction
Precautions for Proper Use
21
Encryption in Network Connection
o
Wireless LAN connections make use of an
encryption function.
This encryption is designed for commerciallysold equipment, and it cannot be altered.
Introduction
LCD Monitor and Viewfinder
o
The LCD monitor and viewfinder screen are
manufactured using high-precision technology.
Black or bright spots may appear on the LCD
monitor and viewfinder screen. This is not a
malfunction. These spots will not be recorded.
o
If you
use this unit continuously for a long period
of time, the characters displayed in the
viewfinder may temporarily remain on the
screen. This phenomenon will not be recorded
to the recording media. They will not appear
after you turn the power off and then on again.
o
If you use this unit in a cold place, the images
may appear to lag on the screen, but this is not
a malfunction. Retained images are not
recorded on the SD card.
o
Do not press against the surface with force or
subject it to strong impact. Doing so may
damage or break the screens.
o
Noise may appear in the viewfinder when
switching between the live video and playback
images.
o
Due to the characteristic of the viewfinder
display device, colors may appear on the
images when you blink your eyes. It does not
affect the recorded images, SDI output, or HDMI
output.
GPS A L
o
The GPS (Global Positioning System) satellites
are managed by the Department of State of the
U.S., and its precision may be altered
intentionally.
o
Perform positioning
with a clear view that is not indoors or blocked
by trees.
o
The time needed for obtaining the position
information may be longer and variation may
also be larger depending on the surrounding
environment and time of day.
o
This camera recorder uses the WGS 84 World
Geodetic System.
o
Signal from GPS satellites may be interrupted by
communication signal from electronic devices
such as mobile phones.
o
Make use of it in accordance with the regulations
of the country, region or location of use.
at an unobstructed location
Copyright
o
Any recordings made on this camera recorder
that are played back for profit or public preview
may infringe on the rights of the owner of the
recordings.
Do not use the recordings for purpose other than
personal enjoyment without prior consent from
the owner. And even for personal enjoyment,
you may not be able to record without
permission from the owner.
License Notices
o
MPEG LA AVC
THIS PRODUCT IS LICENSED UNDER THE
AVC PATENT PORTFOLIO LICENSE FOR
THE PERSONAL USE OF A CONSUMER OR
OTHER USES IN WHICH IT DOES NOT
RECEIVE REMUNERATION TO
(i) ENCODE VIDEO IN COMPLIANCE WITH
THE AVC
(ii) DECODE AVC VIDEO THAT WAS
ENCODED BY A CONSUMER ENGAGED IN A
PERSONAL ACTIVITY AND/OR WAS
OBTAINED FROM A VIDEO PROVIDER
LICENSED TO PROVIDE AVC VIDEO.
NO LICENSE IS GRANTED OR SHALL BE
IMPLIED FOR ANY OTHER USE. ADDITIONAL
INFORMATION MAY BE OBTAINED FROM
MPEG LA, L.L.C. SEE
HTTP://WWW.MPEGLA.COM
o
MPEG LA MPEG-2 Patent
ANY USE OF THIS UNIT IN ANY MANNER
OTHER THAN PERSONAL USE THAT
COMPLIES WITH THE MPEG-2 STANDARD
FOR ENCODING VIDEO INFORMATION FOR
PACKAGED MEDIA IS EXPRESSLY
PROHIBITED WITHOUT A LICENSE UNDER
APPLICABLE PATENTS IN THE MPEG-2
PATENT PORTFOLIO, WHICH LICENSE IS
AVAILABLE FROM MPEG LA, LLC, 6312 S.
WHICH LICENSE IS AVAILABLE FROM MPEG
LA, LLC, 6312 S. Fiddlers Green circle, Suite
400E, Greenwood Village, Colorado 80111
U.S.A.
STANDARD (“AVC VIDEO”) AND/OR
Precautions for Proper Use
22
Rebooting
o
The camera recorder is rebooted when the
following operations are performed.
0
[System]
0
[System] B [Record Set] B
0
[System]
File]/[All File]
0
[System] B [Reset All
0
[Camera Process] B [Reverse Picture]
0
[Network]
0
[Overlay Settings]
L
0
[Overlay Settings
B [Record Set] B [Record Format]
[Time Stamp]
B [Setup File] B[Load File] B [User
]
B [Return over IP] B [Function]
B [Overlay Function] A
] B [Output] AL
Others
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
insert objects other than the memory card
Do not
into the card slot.
Do not block the vent on the unit.
Blocking of the vent causes internal heating and
may lead to burns and fires.
Hot air may be discharged from the vents
depending on the condition of use. This is not a
malfunction.
Do not turn off the [POWER ON/OFF] switch or
remove the power cable during recording or
playback.
The camera recorder may not show stable
pictures for
power is turned on, but this is not a malfunction.
When the video signal output terminals are not
in use, put on the covers to prevent damage to
the terminals.
Do not drop this unit or subject it to strong impact
or vibration as it is a precision equipment.
Optical performance of lens
Due to the optical performance of the lens, color
divergence phenomena (magnification
chromatic aberration) may occur at the
periphery of the image. This is not a camera
malfunction.
Noise may appear in the image when switching
modes.
If placed on its side, heat release efficiency will
deteriorate.
Use the supplied AC adapter as the power
supply. Do not use the supplied AC adapter on
other devices.
Use the
supplied power cord for any other devices.
When the
covers are not in use, put on the covers to
prevent damage to the connectors.
This camera recorder makes use of fonts by
Fontworks Inc.
This camera recorder makes use of M+FONTS.
Use the
and region where it was purchased.
And there are legal restrictions on the use and
outdoor use depending on the country and
region. Please be careful not to violate the law.
This camera recorder has three operation modes - Camera mode, Media mode, and Remote Edit mode.
.
Introduction
Operation Modes
24
Operation ModeDescription
0
is
Camera Mode
0
0
Memo :
0
the camera shooting mode. The camera recorder starts up in Camera mode
This
when the power is turned on.
Camera images are output to the viewfinder and LCD monitor. When a recordable
media is inserted, the camera recorder enters the recording standby mode. “STBY”
appears on the operation mode display area of the LCD monitor and viewfinder.
Press the [REC] trigger button to start recording.
Playback of recording media is not possible in the Camera mode. However, you
can check the most recently recorded video clip.
(A P86 [Viewing Recorded Videos Immediately (Clip Review)] )
Introduction
Media Mode
Remote Edit
Mode
0
This mode
0
When a playable recording media is inserted, the thumbnail or playback screen is
displayed on the viewfinder and LCD monitor.
0
Press and hold the [MODE] selection button to enter the Media mode when you
are not shooting in the Camera mode. Once the camera recorder is in Media mode,
thumbnails of the selected media slot are displayed.
0
This mode enables the list display and editing of the recorded clip data through
access to the clip list display page via a web browser on a smartphone, tablet
terminal, or PC.
0
When you access via a web browser on a smartphone, tablet terminal, or PC, “It
is necessary to change the camera mode to "Remote Edit Mode". Change the
mode.” appears on the web browser. Also,
displayed on the display screen of the camera unit.
Selecting [Change] on the camera recorder and pressing the Set button switches
to the Remote Edit mode, and enables display of the clip list and editing of the clip
metadata.
(A P
A P190 [Uploading a Recording Clip via a Web Browser] )
(
Memo :
0
If you
or PC while recording is in progress, the message appears after recording stops.
0
If playback is in progress, the message appears once the files are closed
automatically, such as when playback stops.
allows you to play back or delete clips recorded on the recording media.
“Change to Remote Edit Mode?” is
188 [ Clip Metadata ] )
access via a web browser on devices such as a smartphone, tablet terminal,
Operation Modes
25
Names of Parts
o
Bottom
A
B
C
D
G
H
F
E
K
L
J
R
X
V
T
W
I
M
O
N
S
Q
P
U
Introduction
.
A
Shoe
For mounting separately sold lights and
accessories.
B
Tally Lamp
(A P47 [Tally Lamp and LED] )
A P236 [Blinking of the Tally Lamp] )
(
C
Built-in Microphone
(A P74 [Audio Recording] )
D
Monitor Speaker
(A P100 [Audio Output during Playback] )
E
Cross-Shaped Button (JKHI)/Set Button (R)
0
For operating the menu and cursor and for
confirming
the settings for time code and user’s bit.
0
When a function is assigned to the cross-
shaped button, it functions as a user button.
(A P46 [Assignment of Functions to User
Buttons] )
F
Tripod Mounting Screw Hole
(A P33 [Attaching the Tripod (Sold
Separately)] )
G
[FIX/VAR/OFF] zoom speed switch
(A P59 [Zoom Operation] )
For switching the zoom speed of the zoom lever
X at the handle.
H
Accessory Mounting Screw Hole
Names of Parts
26
setting, as well as for configuring
a
.
I
Wireless LAN Antenna Terminal A
34 [Attaching the Wireless LAN
(A P
Antennas (Supplied)
J
Viewfinder
A] )
(A P43 [Adjusting the LCD Monitor and
Viewfinder] )
K
Eyecup
Prevents external light from entering the
viewfinder screen and cameraman’s vision.
L
Visibility Adjustment Lever
(A P43 [Adjusting the LCD Monitor and
Viewfinder] )
M
[x] Headphone Jack (Φ3.5 mm)
(A P76 [Monitoring Audio Sound During
Recording Using a Headphone] )
N
[TC IN/OUT] switch
(A P81 [Synchronizing Time Code on
Another Camera] )
O
[TC] TC Input/Output Terminal
(A P76 [Time Code and User’s Bit] )
P
[REC] Record Trigger Button
Starts/stops recording.
Memo :
This switch is interlocked with the [REC/HOLD]
button W at the top of the handle.
Q
[EXP.FOCUS/9] Expanded Focus Assist/User
9 Button
0
For switching the expanded focus ON or
OFF.
(A P62 [Expanded Focus Function] )
0
You can also use it as a user button by
assigning a specific feature in the menu
setting to this button.
R
Zoom Lever at the Grip
(A
P59 [Using the Zoom Lever at the Grip] )
S
Hood Release Button
(A P34 [Attaching/Detaching the Hood] )
T
External Microphone Cable Clamp
(
A P33 [Attaching the External Microphone
(Sold Separately)] )
U
[INPUT1/INPUT2] Audio Input Terminal 1, 2
(XLR 3-pin x 2)
(A P33 [Attaching the External Microphone
(Sold Separately)] )
V
Shoulder Belt Mount (x2)
For mounting a shoulder belt (sold separately).
Caution :
0
Be sure to use a shoulder belt with the strength
to
withstand
0
If the shoulder belt is not properly attached, the
camera recorder may fall and cause injuries.
0
Check the [INSTRUCTIONS] provided with the
shoulder belt before using.
W
[REC/HOLD] Record Trigger Button/Lock
Switch
Starts/stops recording.
Set the switch to [HOLD] to lock the [REC]
Trigger button.
Memo :
0
This switch is interlocked with the [REC]
P on the grip.
0
[REC] button P on the grip is not locked.
X
Zoom Lever on Handle
(A P59 [Using the Zoom Lever at the
Handle] )
the weight of this camera recorder.
Introduction
button
Names of Parts
27
Side Control Panel
J
K
N
L
I
O
P
H
T
M
U
X
Z
V
b
Y
Q
R
S
W
a
A
B
C
D
E
F
G
Introduction
.
A
[FOCUS AUTO/MANU] Focus Switch
A P60 [Focus Operation] )
(
B
[ND FILTER] ND Filter Switch
Use the ND filter to keep the lens aperture in the
appropriate range.
OFF, 1/4, 1/16, 1/64
(A P68 [Setting the ND Filter] )
(A P64 [Adjusting the Brightness] )
(A P69 [Automatic White Balance Mode
(FAW: Fulltime Auto White balance)] )
M
[MARKER/6] Marker/User 6 Button
This button toggles ON/OFF the marker, safety
zone, and center mark displays.
You can also use it as a user button by assigning
a specific feature in the menu setting to this
button.
(A P46 [Assignment of Functions to User
Buttons] )
N
[KEYLOCK ON/OFF] Key Lock Switch
(A P54 [About the Operation Lock Feature
(KEYLOCK)] )
O
[MODE] Camera/Media Mode Selection Button
(A P24 [Operation Modes] )
P
EXT.SLOT Lamp
Lights up in green when a media is inserted into
EXT.SLOT, and lights up in red when the media
is being accessed.
Q
[POWER ON/OFF] Lock Power ON/OFF Switch
Turns ON/OFF the power.
0
down
Hold
the lock button (blue) in the center
to toggle ON/OFF.
0
When the power is turning OFF, “P.OFF”
appears on the LCD monitor and viewfinder.
0
Wait for 5 seconds or more to turn on the
power again.
(A P38 [Turning On/Off the Power] )
R
POWER/CHARGE LED
(
A P35 [Using a Battery Pack] )
S
STATUS LED
(A P148 [ STATUS LED ] )
T
NETWORK LED
(A P148 [ NETWORK LED ] )
Names of Parts
28
U
[ZEBRA/5]
(A P82 [Setting Zebra Pattern] )
You can also use it as a user button by assigning
a specific feature in the menu setting to this
button.
(A P46 [Assignment of Functions to User
Buttons] )
V
[AE LOCK/4] AE Lock/User 4 Button
When Gain, Iris, and Shutter are set to “AUTO”,
their respective values and the value of white
balance are locked when the [AE LOCK/4] button
is pressed.
You can also use it as a user button by assigning
a specific feature in the menu setting to this
button.
(A P46 [Assignment of Functions to User
Buttons] )
W
Cross-Shaped Button (JKHI)/Set Button (R)
The function changes according to the
operation status of the camera recorder.
o
(A P107 [Basic Operations in Menu Screen] )
Set Button (
Cross-shaped Button
(JK)
o
Shutter operation:
Set Button (R):
Cross-shaped Button
(JK)
Cross-Shaped Button
(HI)
X
[ONLINE/3] Online/User 3 Button
0
Switches live streaming between ON/OFF.
(A P208 [Starting Distribution] )
0
You can also use it as a user button by
assigning a specific feature in the menu
setting to this button. Initial setting: Live
streaming
A P46 [Assignment of Functions to User
(
Buttons] )
Y
[OIS/2] Optical Image Stabilizer/User 2 Button
For switching the image stabilizer feature mode
ON or OFF.
You can also use it as a user button by assigning
a specific feature in the menu setting to this
button.
(A P46 [Assignment of Functions to User
Buttons] )
Zebra/User 5 Button
During menu operation (all modes)
R): Confirms menu items
and setting values
: Selects menu items
and setting values
During Camera mode
Shutter ON/OFF
: Switches shutter
speed when shutter
is ON
: AE level operation
Z
[FOCUS ASSIST/1]
For switching the focus assist function ON or
OFF.
(A P61 [Focus Assist Function] )
You can also use it as a user button by assigning
a specific feature in the menu setting to this
button.
(A P46 [Assignment of Functions to User
Buttons] )
a
[MENU/THUMB] Menu/Thumbnail Button
0
Displays the menu screen during Camera
mode.
0
Switches between [Main Menu] and
[Favorites Menu] when the [MENU/THUMB]
button is pressed and held down while the
menu screen is displayed.
(
A P
107 [Basic Operations in Menu Screen] )
0
Displays the
pressed during thumbnail display in the
Media mode.
0
Stops playback and displays the thumbnail
screen when the button is pressed during
playback screen display in the Media mode.
b
[CANCEL] Cancel Button
Cancels various settings and stops playback.
Focus Assist/User 1 Button
menu screen when the button is
Introduction
Names of Parts
29
Rear Terminal
OPEN
BATTERYBATTERIE:
7.2V
N
L
M
I
J
K
C
D
E
B
A
O
G
H
F
Introduction
.
A
SD Card Cover
B
Card Slot A
C
[SLOT SEL
For switching the active card slot during
shooting and playback.
D
[BATT.RELEASE] Button
(A P35 [Removing the Battery] )
] Button
E
Card Slot B
F
[EXT.SLOT]
SSD media adapters (sold separately) such as
KA-MC100 can be inserted into the slot.
(
A P51 [Inserting the SSD Media Adapter] )
G
Battery
(A P35 [Using a Battery Pack] )
H
[DC] Terminal
Input terminal for DC 12 V power supply. For
connecting with the supplied AC adapter.
(A P36 [Using AC Power (DC IN Power)] )
I
[SDI OUT] Terminal
(A P175 [Connecting External Monitor] )
J
[REMOTE] Terminal
(A P176 [Connecting Wired Remote Control] )
K
[LAN] Terminal
For connecting the LAN cable.
L
[HOST] USB Host Terminal
For connecting a USB adapter according to the
intended purpose when you are connecting the
unit to a network.
(A P178 [Camera Setup for Network
Connection] )
M
[HDMI] Terminal
(A P175 [Connecting External Monitor] )
N
[AUX] Terminal (Φ3.5 mm)
For connecting to receiver such as wireless
microphone.
O
Access Lamp A/B
30
Names of Parts
Loading...
+ 222 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.