Jvc GY-DV550-U Schematic

SECTION 4
CHARTS AND DIAGRAMS
SCHEMATIC DIAGRAM NOTES
• Schematic safety precaution
! Parts are safety related parts. When replacing them, be sure to use the specified parts.
• Voltage and waveform measurements
Voltage: Measured with digital voltmeter in DC range;
Waveform: Gray scale illuminated at more than 4000 lux at
3200K lighting.
• Unit of value
Unless otherwise specified
1) Resistance is in (1/6 W)
2) Capacitance is in µF
3) Inductance is in µH
• Expression of wiring
As the following circuit diagram is divided to print on some sheets, such an indication as the following is found in the case the wiring extends over two or more divided sections.
1) Circuit diagram divided into two or more sections:
Board Board Name
16 19 31 32 10
SE DPR SS/CP AUDIO/LCD DV MAIN
Number of
divided sections
1/2 – 2/2 1/4 – 4/4 1/2 – 2/2 1/2 – 2/2 1/7 – 7/7
• Wiring of connector
(Example)
CN11
1
To CN11
2
(P. 4-6)
11
ISB
In the above example, CN11 is connected with CN11 on
11 ISB board.
• Signal flow on the diagram
The following allow marks indicate the specified signal paths respectively.
: Recording or EE signal path : Playback signal ptah : Recording and Playback signal path
• Others
In regard of a board assembly whose circuit is composed of multilayered board patterns such 4- or 6-layered patterns, board patterns of the power supply lines and grounding lines are omit­ted in this section.
Note: For detail of each electrical part, refer to Section 6
ELECTRICAL PARTS LIST by it symbol number.
REPLACING SURFACE MOUNT “CHIP” COMPONENTS
Some resistors, shorting jumpers (0 resistance), ceramic capacitors, transistors, and diodes are chip parts. These chip parts cannot be reused after they are once removed.
Chip resistors used in some circuits are of high precision type having little error in resistance. To demonstrate the full capacity of this set, place an order for proper parts referring to the diagrams and parts lists in the section 5.
Soldering cautions:
1) Do not apply heat for more than 3 seconds.
2) Avoid using a rubbing stroke when soldering.
3) Discard removed chips; do not reuse them.
4) Supplementary cementing is not required.
5) Use care not to scratch or otherwise damage the chips.
CHIP PARTS PIN ARRANGEMENT
[1] Digital transistors
DTC 1
1 2 3
C
R1
R2
BE
DTA 1 DTB 1
1 2 3
C
R1
R2
BE
(Top view) (Top view)
[2] Chip transistors and chip F.E.T.s
2SA 2SB
C
BE
2SC 2SD
C
BE
(Top view) (Top view)
2SJ2SK
G
SD
G
SD
(Top view) (Top view)
[3] Chip diodes
MA143A/MA742 MA142WA MA142A
(Top view)(Top view) (Top view)
2) Indication of wiring which extends to another section: (Example)
A)
This indication that wiring extends to “2/3” of the diagram.
DSP_HD 2/3
Signal name
In the above case, the end of the wiring is connected to the “DSP_HD” on the 2nd section of the diagram.
B)
This indication that wiring extends to DV I/O section of the diagram.
FRP DV I/O
Signal name
In the above case, the end of the wiring is connected to the FRP on the DV I/O section of the diagram.
Two digits show resistance of R1 in abbreviation.
1
43 : 4.7 k 14 : 10 k 24 : 22 k 44 : 47 k
Roman letter show the resistive ratio between R1 and R2
2
in abbreviation.
E : R2/R1 = 1/1 Y : R2/R1 = 5/1 W : R2/R1 = 2/1 X : R2/R1 = 1/2 T : R2 is opened.
Symbol the shape of resistor in abbreviation.
3
4-14-1
4.1 INDEX TO PAGES OF MAIN BOARDS AND CIRCUIT BOARD LOCATION
4.1.1 Circuit board location
03 ROM
37 SENS2
10 DV MAIN
33 REG
17 PS
15 CAM 14 TG
36 SEN1
42 CONNECT
53 TA 3
38 REMOTE 28 BNC
Left-hand side
19 DPR
27 MIC
42 CONNECT
Rear
18 IF2
11 ISB 12 ISG 13 ISR
23 SWF
21 IF
25 SWRB 26 SWPB
24 SWRM
20 JOG
34 MT
16 SE
31 SS/CP
22 SWRU 35 OPE 32 AUDIO/LCD
Right-hand side
57 AD
54 TA 4
50 CT
52 26P
56 CN
55 BNC
AD frame left-hand side
– –
– – –
4-33
4-33 4-44 4-46
– –
4-45
4-61 4-61 4-61
– – – –
Page of diagram
Schematic diagram
4-3
4-42
4-52,53
4-56 4-42 4-55
4-43 to 49
4-4
4-6 4-8
4-16, 17
4-31 4-32
4-10 to 13
4-24 4-32 4-24 4-25 4-25 4-25 4-25 4-25
Circuit board
– –
4-54 4-57 4-42 4-57
4-50, 51
4-5
4-7
4-9 4-18 4-33 4-33
4-14,15
4-26 4-33 4-26 4-26 4-26 4-26 4-26 4-26
Board
No.
28 29 31 32 33 34 35 36 37 38 39 40 41 42 43 50 51 52 53 54 55 56 57
Board Name
BNC FL SS/CP AUDIO/LCD REG MT OPE SEN1 SENS2 REMOTE AU JUNK XLR PWR JUNC CONNECT EAR.J CT P.SEL 26P TA3 TA4 BNC CN AD
Block diagram
4-47 4-48 4-64
Board
No.
01 02 03 04 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
Board Name
OVERALL
OVERALL (DVC UNIT) PR & MDA DCDC ROM CONN. DV MAIN ISB ISG ISR TG CAM SE PS IF2 DPR JOG IF SWRU SWF SWRM SWRB SWPW MIC
Block diagram
4-66,67
4-66,67
Note: Only thesection marked thus are described in this service manuai.
For those section that are not described, please refer to the service manual of GY-DV500U/E No. 60125.
– –
– – – – – – – – – – – – – – – – – –
40 XLR
43 EAR. J 41 PWR JUNC 39 AV JUNK
Page of diagram
Schematic diagram
4-25
4-19, 20 4-25, 26
4-34 4-22 4-37 4-38 4-38 4-38 4-36 4-38 4-37 4-38 4-38 4-40 4-40 4-40 4-40 4-40 4-40 4-40 4-40
Circuit board
4-26 4-26 4-21
4-27 to 30
4-35
4-23, 24
4-39 4-39 4-39 4-39 4-39 4-39 4-39 4-39 4-39 4-41 4-41 4-41 4-41 4-41 4-41 4-41 4-41
Bottom
01 PR & MDA
51 P.SEL
AD frame right-hand side
04 CONN
02 DCDC
DVC unit
4-24-2
4.2 総合結線図
4.2 OVERALL WIRING DIAGRAM
GY-DV550 GY-DV550
Page 4-40
Page 4-40
Page 4-40
Page 4-4
Page 4-4
Page 4-4
Page 4-6
Page 4-8
Page 4-10
Page 4-38
Page 4-38
Page 4-16
Page 4-22
Page 4-32
Page 4-31
Page 4-40
Page 4-40
Page 4-40
Page 4-40
Page 4-40
Page 4-32
Page 4-34
Page 4-25
Page 4-37
Page 4-19
Page 4-37
Page 4-38
Page 4-36
Page 4-38
Page 4-38
Page 4-38
4-3 4-3
SC92683
4.3 ISB/ISG/ISR基板基準回路図 
GY-DV550 GY-DV550
4.3 ISB/ISG/ISRSCHEMATIC DIAGRAM 
-7.6
-7.6
-0.7
11.0
-0.2
-8.0
10.9
3.4
7.2
1.4
1.8
3.9
2.8
1.7
1.7
TO
 TG
CN11 Page 4-6
0.1
1.7
-7.6
-7.6
-0.7
11.0
-0.2
-8.0
10.2
3.4
3.9
7.2
1.4
1.8
TO
 TG
CN12, 13
Page 4-6
10.9
10.2
4-4
2.8
4-4
1.7
1.7
0.1
1.7
SC92692
4.4 ISB/ISG/ISR基板部品配置図
4.4 ISB/ISG/ISR CIRCUIT BOARD
GY-DV550 GY-DV550
ISB
 SIDE A   SIDE B 
ABC CBA
1
2
1
2
33
ISG
ABC
 SIDE A   SIDE B 
CBA
1
2
1
2
33
基板上の部品配置アドレス表
アドレスは1区間の誤差がある場合があります。
 ADDRESS TABLE OF BOARD PARTS
Each address may have an address error by one interval.
A-1C
Side
A-2A
IC501
A-2A
IC503
A-1A
IC504
B-3C
IC505
A-1A
Q501
B-1A
Q502
B-3A
R501
B-2B
R502
B-1B
R503
B-1B
R504
A-1A
R505
A-1B
R506
基板上の部品配置アドレス表
アドレスは1区間の誤差がある場合があります。
 ADDRESS TABLE OF BOARD PARTS
Each address may have an address error by one interval.
A-1C
Side
A-2A
IC501
A-1A
IC503
A-2A
IC504
B-1A
IC505
B-3B
Q501
B-3B
Q502
B-2B
R501
B-2A
R502
B-3A
R503
B-3A
R504
B-3C
R505
A-2A
R506
R507 R508 R509 R510 R511 R512 R513 R514 R524 R525
C501 C504 C505
R507 R508 R509 R510 R511 R512 R513 R514 R524 R525
C501 C504 C505
Y axis X axis
Y axis X axis
A-1B A-1B A-1B A-1B B-3C B-3B B-3C B-3B B-1A B-1A
B-1A B-2B B-2B
A-2A A-2A A-3B A-2B B-1A B-1A B-1A B-1A B-3C B-3C
B-2B B-2A B-2A
C506 C507 C508 C509 C510 C511 C512 C513 C514 C515 C518 C519 C520 C521
C506 C507 C508 C509 C510 C511 C512 C513 C514 C515 C518 C519 C520 C521
B-1C B-1A A-1A A-1A B-1C B-1C B-2C B-2A A-1C A-3C B-2B A-3A A-1B A-1A
B-3A B-2C A-1A A-1A B-1B B-3C B-1C A-2A A-3C A-1C A-1A B-2C A-2B A-3A
C522 C526 C527
LC501
CN11
C522 C526 C527
CN12
LC501
B-2C A-1C B-2C
B-1C
A-2C
B-2C A-3C B-1C
A-2C
B-2C
ISR
 SIDE A   SIDE B 
ABC
基板上の部品配置アドレス表
アドレスは1区間の誤差がある場合があります。
CBA
1
2
1
2
33
 ADDRESS TABLE OF BOARD PARTS
Each address may have an address error by one interval.
A-1C
Side
IC501 IC503 IC504 IC505
Q501 Q502
R501 R502 R503 R504 R505 R506
A-2A A-1A A-2A B-1A
B-3B B-3B
B-2B B-2A B-3A B-3A B-3C A-2A
R507 R508 R509 R510 R511 R512 R513 R514 R524 R525
C501 C504 C505
Y axis X axis
A-2A A-2A A-3B A-2B B-1A B-1A B-1A B-1A B-3C B-3C
B-2B B-2A B-2A
C506 C507 C508 C509 C510 C511 C512 C513 C514 C515 C518 C519 C520 C521
B-3A B-2C A-1A A-1A B-1B B-3C B-1C A-2A A-3C A-1C A-1A B-2C A-2B A-3A
C522 C526 C527
CN12
LC501
B-2C A-3C B-1C
A-2C
B-2C
4-5 4-5
4.5 TG基板基準回路図 
4.5 TG SCHEMATIC DIAGRAM 
GY-DV550 GY-DV550
TO
 ISB
CN11 Page 4-4
TO
 ISG
CN12 Page 4-4
27
NC
0
-7.6
-7.6
-0.5
-8.0
-8.0 -0.7
4.6
4.9
4.6
0.1
4.9
-0.2
4.9
0.1
27
27
4.8
4.8
0
0.4
56
56
56
1.9 2.2
0.1
0
4.4
R2 OPEN
4.9
4.7
6.7
Gate
Pulse
H Reset
V Reset
1/2
Gen
V Rom
Latch
Mode
5
Driver
0
0
4.9
7.7
R19
0
4.7
5.1
K8 0
3.1
3.1
0
0.3
4.9
2.9
4.9
4.7
0
4.9
0.1
0.1
4.9
0.1 0
0
4.9
56
56
5.2
4.9
2.3
3.5
0.7
0.4
1.6
3.1
0
3.1
0
4.9
0
4.9
4.9
3.2
1.6
TO
 CAM
0
CN14 Page 4-8
TO
 ISR
CN13 Page 4-4
4-6 4-6
0
0
5
0
SC92691
4.6 TG基板部品配置図
4.6 TG CIRCUIT BOARD
GY-DV550 GY-DV550
 SIDE A   SIDE B 
基板上の部品配置アドレス表
アドレスは1区間の誤差がある場合があります。
 ADDRESS TABLE OF BOARD PARTS
Each address may have an address error by one interval.
A-1C
Side
Y axis X axis
IC1 IC2 IC3 IC4 IC5 IC6 IC7 IC8 IC9 IC10 IC11 IC12 IC13 IC14 IC16 IC19
A-4B B-4G B-4E B-4D A-6F B-2F B-2D A-6C A-2B B-2B B-1B B-6E B-6D B-4C B-1E B-5A
IC21
Q1
D1 D2 D3 D4 D5
R1 R2 R3 R4 R5 R6
B-4A
A-5D
B-3G B-3E B-3D A-5G A-6E
A-4B B-5B B-3G A-5G B-3E A-5E
R7 R8 R9 R10 R11 R12 R13 R14 R15 R16 R17 R18 R19 R20 R21 R22
B-3D A-5D B-5B A-6D A-6D A-6D B-1E B-5B B-5A B-2D B-2C B-3A B-4B B-3A B-3A B-2A
R23 R24 R25 R26 R27 R28
C1 C2 C3 C4 C5 C6 C7 C8 C9
B-3G
C10
A-3A
B-3E
C11
A-3A
B-3D
C12
B-1C
A-3B
C13
B-1C
B-5C
C14
B-1C
B-6E
C15
B-1C
B-6F
C16
B-6D
C17
A-5A
B-1E
C18
A-5A
B-5B
C19
A-4A
A-6C
C20
B-2F
A-4F
C21
A-2F
A-5G
C22
A-2F
B-4F
C23
B-2E
A-4E
C24
B-2D
A-5F
C25
B-2D
4-7 4-7
C26 C27 C28 C29 C30 C31 C32 C33 C34 C35 C36 C37 C38 C39 C40 C41
B-4E A-4D A-5D B-4C A-6F A-6E A-6E A-6D A-6C A-6F A-6E A-4G A-4F A-4D A-5G A-5F
C42 C43 C44 C45 C46 C47 C48 C49 C50 C51 C52 C53 C54 C55 C56 C57
A-5E A-5E A-5D A-5D A-4C B-4C A-4A A-4C B-2A B-1F B-2D B-2B B-4A B-5B B-5A B-6E
C58 C59 C60 C61 C62 C63 C64 C65 C66 C67
K1 K2 K3 K4 K5
B-5C B-4C A-2C B-5B B-1F B-5A B-2B B-1B A-4C B-2B
A-4C A-4C A-2E A-2E B-2G
K6 K7 K8 K9 K10 K11 K12 K13 K14 K15 K16 K17 K18 K19 K20 K21
A-2G A-2F A-4A A-2D A-2D B-5F B-5F B-3F B-5E B-5E B-3E B-4C B-4C B-3C A-2G A-2G
K22 K23 K24 K25 K26 K27 K28 K29 K30 K31 K32 K33
TB1 TB2 TB3
A-2G B-1F B-2B A-6C B-5C B-1B B-1E A-6E B-6E B-6D B-5C A-6G
B-6B B-6G B-1G
TB4
CN11 CN12 CN13 CN14 CN100
LC2
B-1A
A-3G A-3E A-3D A-1F A-1C
B-5A
Loading...
+ 16 hidden pages