JVC AV-20F703 Service Manual

SERVICE MANUAL

COLOR TELEVISION

AV-20F703

CATV

VCR

DVD

POWER

STANDARD

INPUT

BBE

DISPLAY

RETURN

SLEEP TIMER

C.C.

AUDIO SELECT

LIGHT

RM-C309G

MUTING

ENTER

VOL VOL

EXITMENU

– VCR CHANNEL

VCR/DVD

TV/VCR

PREV NEXT

POWER

PLAY

STOPREC

OPEN/CLOSE STILL/PAUSE

FFREW

PAUSE

POWER

CONTENTS

a SPECIFICATIONS....................................................................................................................................2

a OPERATING INSTRUCTIONS (APPENDIX)

a SAFETY PRECAUTIONS ........................................................................................................................ 3

a SPECIFIC SERVICE INSTRUCTIONS .................................................................................................... 4

a SERVICE ADJUSTMENTS ......................................................................................................................9

a GUIDE FOR REPAIRING ....................................................................................................................... 14

a STANDARD CIRCUIT DIAGRAM ........................................................................................................ 2-1

a PARTS LIST ...........................................................................................................................................21

No. 52001

May 2002

AV-20F703

SPECIFICATIONS

TELEVISION

Picture Tube: 20” (measured diagonally)

Color System: NTSC

TV RF System: CCIR (M)

Tuner Type: 181 Channel, Quartz PLL Frequency Synthesized

Receiving Channels: VHF 2-13

UHF 14-69

CATV 01-97 (5A)-(A-3)

98-99 (A-2)-(A-1)

14-22 (A)-(I)

23-36 (J)-(W)

37-65 (AA)-(FFF)

66-125 (GGG)-(125)

Intermediate Frequency: Picture (FP) : 45.75 MHz

Sound (FS) : 41.25 MHz

FP-FS : 4.50 MHz

Antenna Input: VHF/UHF In 75 ohms coaxial, F-Type Connector

Speaker: 2” x 4-3/4”, 8 ohms x 2

Audio Output Power: 2.5 W + 2.5 W

GENERAL

Power Source: 120 V AC, 60 Hz

Power Consumption: 105 Watts

Dimensions(W x H x D): 23-1/4” (590 mm) x 17-1/2” (444 mm) x 19-3/4” (498.5 mm)

Weight: 50.6 Ibs/23 kg

Video/Audio Inputs: Component input

Y input: 1.0 Vp-p, 75 ohm (RCA pin jack)

Pb, Pr input : 0.7 Vp-p, 75 ohm (RCA pin jack)

S-Video input

Y input: 1.0 Vp-p, 75 ohm

C input: 0.3 Vp-p, 75 ohm

Video input: 1.0 Vp-p, 75 ohm (RCA pin jack)

Audio input: -8dB, 47 kohm (RCA pin jack)

Headphone Jack: 3.5 mm mini-jack

Storage Temperature -20 °C ~ 60 °C

Operating Temperature 5 °C ~ 40 °C

Accessories:

Remote Control X 1

Batteries (UM-3) X 2

Design & specification are subject to change without notice.

2 No. 52001

SAFETY PRECAUTIONS

SERVICING NOTICES ON CHECKING

As for the places which need special attentions, they are indicated with the labels or seals on the cabinet, chassis and parts. Make sure to keep the indications and notices in the operation manual.

2. AVOID AN ELECTRIC SHOCK

There is a high voltage part inside. Avoid an electric shock while the electric current is flowing.

3. USE THE DESIGNATED PARTS

The parts in this equipment have the specific characters of incombustibility and withstand voltage for safety. Therefore, the part which is replaced should be used the part which has the same character. Especially as to the important parts for safety which is indicated in the circuit diagram or the table of parts as a mark, the designated parts must be used.

4. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER ASSEMBLING OR WIRING

There are parts which use the insulation material such as a tube or tape for safety, or which are assembled in the condition that these do not contact with the printed board. The inside wiring is designed not to get closer to the pyrogenic parts and high voltage parts. Therefore, put these parts in the original positions.

5. TAKE CARE TO DEAL WITH THE CATHODE-RAY TUBE

In the condition that an explosion-proof cathoderay tube is set in this equipment, safety is secured against implosion. However, when removing it or serving from backward, it is dangerous to give a shock. Take enough care to deal with it.

6. AVOID AN X-RAY1. KEEP THE NOTICES

Safety is secured against an X-ray by considering about the cathode-ray tube and the high voltage peripheral circuit, etc. Therefore, when repairing the high voltage peripheral circuit, use the designated parts and make sure not modify the circuit. Repairing except indicates causes rising of high voltage, and it emits an X-ray from the cathoderay tube.

PERFORM A SAFETY CHECK AFTER

7. SERVICING

Confirm that the screws, parts and wiring which were removed in order to service are put in the original positions, or whether there are the portions which are deteriorated around the serviced places serviced or not. Check the insulation between the antenna terminal or external metal and the AC cord plug blades. And be sure the safety of that.

(INSULATION CHECK PROCEDURE)

Unplug the plug from the AC outlet.

Remove the antenna terminal on TV and turn on the TV.

Insulation resistance between the cord plug terminals and the eternal exposure metal [Note 2] should be more than 1M ohm by using the 500V insulation resistance meter [Note 1].

If the insulation resistance is less than 1M ohm, the inspection repair should be required.

[Note 1]

If you have not the 500V insulation resistance meter, use a Tester.

[Note 2]

External exposure metal: Antenna terminal

Earphone jack

AV-20F703

HOW TO ORDER PARTS

Please include the following informations when you order parts. (Particularly the VERSION LETTER.)

1. MODEL NUMBER and VERSION LETTER The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be

found at the end of the SERIAL NUMBER.

2. PART NO. and DESCRIPTION You can find it in your SERVICE MANUAL.

IMPORTANT

Inferior silicon grease can damage IC's and transistors. When replacing an IC's or transistors, use only specified silicon grease (YG6260M). Remove all old silicon before applying new silicon.

Licensed by BBE Sound, Inc. under USP4638258 and 4482866. BBE and BBE symbol are registered trademarks of BBE Sound, Inc.

No. 52001 3

AV-20F703

SPECIFIC SERVICE INSTRUCTIONS

DISASSEMBLY INSTRUCTIONS

1. REMOVAL OF ANODE CAP

Read the following NOTED items before starting work.

After turning the power off there might still be a potential voltage that is very dangerous. When removing the Anode Cap, make sure to discharge the Anode Cap's potential voltage. Do not use pliers to loosen or tighten the Anode Cap

terminal, this may cause the spring to be damaged.

REMOVAL

1. Follow the steps as follows to discharge the Anode Cap.

(Refer to Fig. 1-1.)

Connect one end of an Alligator Clip to the metal part of a flat-blade screwdriver and the other end to ground. While holding the plastic part of the insulated Screwdriver, touch the support of the Anode with the tip of the Screwdriver. A cracking noise will be heard as the voltage is discharged.

GND on the CRT

3. After one side is removed, pull in the opposite direction to remove the other.

NOTE

Take care not to damage the Rubber Cap.

INSTALLATION

1. Clean the spot where the cap was located with a small amount of alcohol. (Refer to Fig. 1-3.)

NOTE

Confirm that there is no dirt, dust, etc. at the spot where the cap was located.

Location of Anode Cap

Fig. 1-3

2.3.Arrange the wire of the Anode Cap and make sure the wire is not twisted. Turn over the Rubber Cap. (Refer to Fig. 1-4.)

Screwdriver

Alligator Clip

GND on the CRT

Flip up the sides of the Rubber Cap in the direction of the

2. arrow and remove one side of the support.

(Refer to Fig. 1-2.)

Rubber Cap

CRT

4 No. 52001

Support

CRT

Fig. 1-1

Fig. 1-2

4. Insert one end of the Anode Support into the anode button, then the other as shown in Fig. 1-5.

Support

CRT

5.6.Confirm that the Support is securely connected. Put on the Rubber Cap without moving any parts.

Fig. 1-4

Fig. 1-5

DISASSEMBLY INSTRUCTIONS

AV-20F703

2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC

REMOVAL

1. Put the Masking Tape (cotton tape) around the Flat

Package IC to protect other parts from any damage.

(Refer to Fig. 2-1.)

NOTE

Masking is carried out on all the parts located within 10 mm distance from IC leads.

Masking Tape (Cotton Tape)

2. Heat the IC leads using a blower type IC desoldering

machine. (Refer to Fig. 2-2.)

NOTE

Do not add the rotating and the back and forth directions force on the IC, until IC can move back and forth easily after desoldering the IC leads completely.

Fig. 2-1

Blower type IC desoldering machine

3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.)

NOTE

Some ICs on the PCB are affixed with glue, so be careful not to break or damage the foil of each IC leads or solder lands under the IC when removing it.

Blower type IC desoldering machine

Tweezers

4.5.Peel off the Masking Tape. Absorb the solder left on the pattern using the Braided Shield Wire. (Refer to Fig. 2-4.)

NOTE

Do not move the Braided Shield Wire in the vertical direction towards the IC pattern.

Fig. 2-3

Braided Shield Wire

Soldering Iron

Fig. 2-2

IC pattern

Fig. 2-4

No. 52001 5

AV-20F703

DISASSEMBLY INSTRUCTIONS

INSTALLATION

1. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.

(Refer to Fig. 2-5.)

Soldering Iron

Solder temporarily Solder temporarily

Fig. 2-5

2. Supply the solder from the upper position of IC leads sliding to the lower position of the IC leads. (Refer to Fig. 2-6.)

4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thintip Soldering Iron. (Refer to Fig. 2-8.)

Thin-tip Soldering Iron

Fig. 2-8

5. Finally, confirm the soldering status on four sides of the IC using a magnifying glass. Confirm that no abnormality is found on the soldering position and installation position of the parts around the IC. If some abnormality is found, correct by resoldering.

NOTE

When the IC leads are bent during soldering and/or repairing, do not repair the bending of leads. If the bending of leads are repaired, the pattern may be damaged. So, be always sure to replace the IC in this case.

Solder

Supply soldering from upper position to lower position

Soldering Iron

3. Absorb the solder left on the lead using the Braided Shield Wire. (Refer to Fig. 2-7.)

NOTE

Do not absorb the solder to excess.

Soldering Iron

Braided Shield Wire

Fig. 2-6

Fig. 2-7

6 No. 52001

SERVICE MODE LIST

This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 1 second.

Set Key Remocon Key Operations

VOL. (-) MIN 0 Releasing of V-CHIP PASSWORD.

Initialization of the factory.

VOL. (-) MIN 1

VOL. (-) MIN 3

VOL. (-) MIN 6

NOTE: Do not use this for the normal servicing.

If you set a factory initialization, the memories are reset such as the channel setting, and the POWER ON total hours.

Remocon format selection. (JVC format NEC format) NOTE: Supplied remocon can not be operated at NEC format. (The “N” is always displayed on the monitor.) Do not use this for the normal servicing.

POWER ON total hours is displayed on the screen. Refer to the “CONFIRMATION OF HOURS USED.

Can be checked of the INITIAL DATA of MEMORY IC. Refer to the “WHEN REPLACING EEPROM (MEMORY) IC”.

AV-20F703

VOL. (-) MIN 8

VOL. (-) MIN 9

Writing of EEPROM initial data. NOTE: Do not use this for the normal servicing.

Display of the Adjustment MENU on the screen. Refer to the “ELECTRICAL ADJUSTMENT” (On-Screen Display Adjustment).

CONFIRMATION OF HOURS USED

POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation.

NOTE: If you set a factory initialization, the total hours is reset to “0”.

Set the VOLUME to minimum.

Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second.

After the confirmation of using hours, turn off the power.

INIT 00 A9

CRT ON 0010

Initial setting content of MEMORY IC.

POWER ON total hours.

= (16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value)

No. 52001 7

+ 14 hidden pages