Auto-lifter(Side-plate-mounting type)
AK118
/
INSTRUCTION MANUAL / PARTS LIST
AK118 DDL-9000, DLN-
9010/9010A DDL-9000, DLN-9010/9010A
AK118 DDL-9000, DLN-9010/9010A
Read safety instructions carefully and understand them before using.
Retain this Instruction Manual for future reference.
CAUTION
This Instruction Manual is intended for the AK118. Read and fully understand the instructions given under “IMPORTANT SAFETY INSTRUCTIONS” in the Instruction Manual the DDL-9000 or DLN-9010/9010A before putting the machine into service when this device is installed to the DDL-9000 or DLN-9010/9010A .
In addition, to emphasize the AK118, some illustrations of the DDL-9000 or DLN-
9010/9010A are simplified. Also, illustrations of the safety devices are partially omitted.
No.04
29327905
|
|
|
1. |
.............................................................................................................................. |
1 |
2. |
....................................................................................................... |
5 |
3. |
................................................................................... |
7 |
4. |
............................................................................................................................................. |
7 |
5. |
.............................................................................................................................. |
8 |
|
CONTENTS |
|
1. |
INSTALLATION.................................................................................................................. |
1 |
2. |
HOW TO SELECT THE FUNCTION OF AUTO-LIFTER................................................... |
5 |
3. |
HOW TO SELECT THE FUNCTION OF LIFTING THE PRESSER FOOT |
|
|
AUTOMATICALLY AFTER THREAD TRIMMING.............................................................. |
7 |
4. |
SPECIFICATIONS.............................................................................................................. |
7 |
5. |
PARTS LIST....................................................................................................................... |
8 |
1. / INSTALLATION
WARNING :
Turn OFF the power before starting the work so as to prevent accidents caused by abrupt start of the sewing machine.
[ DDL-9000 / In case of DDL-9000 ]
1
1)Remove the side plate of the machine, and remove hinge screw in knee lifter side rod .
2
ください。
2)Remove hinge screw in knee lifter link , and replace it with knee lifter link set with attached spring . Then install the knee lifter link with hinge screw .
At this time, tilt the machine and make sure that knee lifter connecting rod enters the hole of connecting rod guide .
3
3)Tighten with screw knee lifter side rod pin to replaced knee lifter link , and install knee lifter side rod with pin .
1.
(Caution) 1. Securely tighten knee lifter side rod pin since it is easily loosened.
2.Apply grease to the hinge sections of respective hinge screws.
– 1 –
|
|
|
|
|
Notch |
|
4
5
4)Install knee lifter link spring hook on wire pressing base so as to hold down thread release wire and oil tube . At this time, be careful about routing of oil tube and thread release wire .
5)Place knee lifter link spring on the notch of knee lifter link spring hook .
[ DLN-9010/9010A / In case of DLN-9010/9010A ]
|
|
|
1 |
||
|
|
|
|||
|
|
|
2 |
||
|
|
|
|
||
|
|
|
3 |
||
|
|
|
|
|
|
|
|
|
1) Remove the side plate of the machine. |
||
|
|
2) Remove hinge screw in knee lifter link , and |
|||
|
|
|
|||
|
|
|
set attached spring . Then tighten again hinge |
||
|
|
|
screw . |
|
|
|
|
|
3) Install attached knee lifter side rod pin in knee |
||
|
|
|
lifter link . |
|
|
|
|
|
4 |
||
|
|
|
|||
|
|
|
|||
|
|
||||
|
|
|
4) Place knee lifter link spring on the notch of wire |
||
|
|
|
pressing base which is installed on the machine |
||
|
|
|
head. |
|
|
|
|
|
DLN-9010/9010A |
||
|
|
|
|
|
|
|
/Notch |
|
GAKA1840000 |
|
|
|
|
GAKA1841000 |
|
||
|
|
|
GAK330400A0 |
( ) |
|
|
|
|
|
|
(1 ) |
|
|
|
SS4110715SP |
|
|
|
|
|
GAKA1843000 |
|
|
|
|
|
|
|
|
|
|
|
In case of DLN-9010/9010A, the spare parts below |
||
|
|
|
are not used. |
|
|
|
|
|
|
|
|
|
|
|
• GAKA1840000 |
Knee lifter link spring hook |
|
|
|
|
• GAKA1841000 |
Knee lifter link |
|
|
|
|
• GAK330400A0 |
Knee lifter side rod pin (asm.) (Only one) |
|
|
|
|
• SS4110715SP |
Screw |
|
|
|
|
• GAKA1843000 |
Knee lifter link fulcrum shaft |
|
|
|
– 2 – |
|
|