How it Works
JRC
Loading...
JMR-7282-SH
Installation Manual
100 pgs4.66 Mb0
Instruction Manual
138 pgs2.83 Mb0
Instruction Manual
102 pgs3.35 Mb0

JRC JMR-7225-7X3, JMR-7225-9X, JMR-7225-9X3, JMR-7225-6X, JMR-7230-S Instruction Manual

...
Download
Page 1
Overview
1
Name and Function of Each Unit
2
Common Basic Operations
3
Range and Bearing Measurement Methods
4
Basic Operation of the Radar
5
Target Tracking and AIS
6
True and False Echoes on Display
7
Functions of the ECDIS
8
Route Planning
9
Route Monitoring
10
Monitoring a Dragging Anchor
11
Automatic Sailing
12
Operating a Chart
13
Creating a User Map/ Updating a Chart Manually
14
Logbook
15
Setting Up Screen View
16
Setting Up Alerts
17
Setting Up the Operation Mode
18
Adjusting and Setting Up Equipment (for Services)
19
Playing Back Data Recorded During Navigation [Playback]
20
Maintenance & Inspection
21
Failures and After-Sale Services
22
About Disposal
23
Specifications
24
Radar Antenna Block Diagrams
APP A
Alert List
APP B
Setting the Interswitch
APP C
Menu List and Materials
APP D
JMR-7230-S3/S JMR-7225-7X3/9X3/6X/9X/6XH JMR-7210-6X/6XH JMR-7272-S JMR-7282-S/SH JMR-9230-S3/S JMR-9225-7X3/9X3/6X/9X/6XH JMR-9210-6X/6XH JMR-9272-S JMR-9282-S/SH
Marine Radar Equipment
Instruction Manual
<Function>
Page 2
Page 3
㻌
㻌
㻌 (1) Contents
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Contents
Function
Section 5 Basic Operation of the Radar ....................................................... 5-1
5.1 Overview Flowchart ............................................................................................................... 5-1
5.2 Starting and Shutting Down the Radar .................................................................................. 5-3
5.2.1 Powering on and starting .............................................................................................. 5-3
5.2.2 Exiting radar operation .................................................................................................. 5-6
5.3 Observation Environment and Image Adjustment ................................................................ 5-7
5.3.1 Adjusting screen brightness .......................................................................................... 5-7
5.3.2 Changing the observation range ................................................................................... 5-7
5.3.3 Adjusting tune ............................................................................................................... 5 - 9
5.3.4 Adjusting gain ............................................................................................................. 5-10
5.3.5 Rejecting sea clutter (Sea) ......................................................................................... 5-12
5.3.6 Rejecting rain/snow clutter .......................................................................................... 5-14
5.3.7 Adjusting to optimal images (Selection of observation scenes) ................................. 5-16
5.4 General Radar Operation .................................................................................................... 5-19
5.4.1 Interference Rejection (IRFunction) .......................................................................... 5-19
5.4.2 Changing the transmitter pulse length ........................................................................ 5-20
5.4.3 Enhancing targets ....................................................................................................... 5-21
5.4.4 Using video processing (Echo Process) ..................................................................... 5-22
5.4.5 Setting the azimuth mode ........................................................................................... 5-23
5.4.6 Setting a motion mode ................................................................................................ 5-25
5.4.6.1 Resetting Own Ship to its Initial Position in [TM] (True Motion display) Mode ..... 5-26
5.4.7 Setting the Stabilization Mode .................................................................................... 5-27
5.4.8 Moving own ship’s display position (Off Center) ......................................................... 5-27
5.4.9 Displaying other ship’s trails (Trails) ........................................................................... 5-28
5.4.9.1 Trails motion mode ............................................................................................... 5-28
5.4.9.2 Changing motion mode of trails ............................................................................ 5-30
5.4.9.3 Setting the length of the trail ................................................................................. 5-30
5.4.9.4 Clearing trails data ................................................................................................ 5-31
5.4.10 Doubling the size of radar image ................................................................................ 5-32
5.4.11 Hiding the heading line (HL OFF) ............................................................................... 5-34
5.4.12 Hiding graphics information on radar display ............................................................. 5-35
5.4.13 Setting true bearing ..................................................................................................... 5-35
5.4.14 Setting own ship speed ............................................................................................... 5-36
5.4.14.1 Switching own ship speed device ......................................................................... 5-36
5.4.14.2 Entering the ship’s heading/own ship’s speed manually ...................................... 5-38
Section 6 Target Tracking and AIS ............................................................... 6-1
7ZPNA4447A
Page 4
Contents (2)
6.1 Restrictions ........................................................................................................................... 6-2
6.2 Collision Avoidance Issue (Explanation) ............................................................................... 6-3
6.2.1 Collision Avoidance in Navigation ................................................................................. 6-3
6.2.2 Marine Accidents and Collisions ................................................................................... 6-3
6.2.3 Basic Concept of Collision Avoidance .......................................................................... 6-4
6.2.4 Relative Vector and True Vector ................................................................................... 6-5
6.2.5 Radar and Collision Avoidance ..................................................................................... 6-5
6.3 Displaying Symbols ............................................................................................................... 6-6
6.3.1 Displaying/hiding target tracking symbols/AIS target symbols ..................................... 6-6
6.3.2 Types and Definitions of Target Tracking Symbols ....................................................... 6-6
6.3.3 Types and Definitions of AIS Target Symbols ............................................................... 6-7
6.3.4 About AIS AtoN (Aids to Navigation) ........................................................................... 6-10
6.3.5 About AIS-SART Information ...................................................................................... 6-10
6.3.6 About Display Priority of AIS Targets .......................................................................... 6-10
6.3.7 Switching between Ground Vector and Water Vector ................................................. 6-11
6.3.8 Association Target Symbols ........................................................................................ 6-11
6.4 Preparation .......................................................................................................................... 6-12
6.4.1 Setting the Cursor Mode to AUTO Mode .................................................................... 6-12
6.4.2 Setting Vector .............................................................................................................. 6-12
6.4.2.1 Vector modes ........................................................................................................ 6-12
6.4.2.2 Setting vector mode .............................................................................................. 6-14
6.4.2.3 Vector Length (Vector Time) ................................................................................. 6-14
6.4.2.4 Setting the Vector Length ..................................................................................... 6-15
6.4.3 Setting collision decision criteria ................................................................................. 6-15
6.4.3.1 Setting CPA limit ................................................................................................... 6-15
6.4.3.2 Setting TCPA limit ................................................................................................. 6-16
6.4.4 Showing the CPA ring (RADAR only) ......................................................................... 6-17
6.5 Setting and Operating Target Tracking ............................................................................... 6-18
6.5.1 Acquiring target ........................................................................................................... 6-18
6.5.1.1 Automatic acquisition (automatic acquisition) mode ............................................ 6-18
6.5.1.2 ACQ MANUAL (manual acquisition) mode........................................................... 6-19
6.5.1.3 Using manual acquisition and auto acquisition together ...................................... 6-20
6.5.2 Setting up the automatic acquisition/activation zone (AZ) .......................................... 6-20
6.5.2.1 Using "New Target Warning" dialog box in the [Alert] menu ................................ 6-21
6.5.2.2 Using the cursor ................................................................................................... 6-22
6.5.2.3 Using the EBL/VRM dial for the setting ................................................................ 6-23
6.5.3 Tracked target information display .............................................................................. 6-24
6.5.4 Erasing unwanted tracked targets .............................................................................. 6-25
6.5.5 Displaying Target ID No. ............................................................................................. 6-26
6.5.6 Editing tracked target properties ................................................................................. 6-28
6.5.6.1 Adding Tracked Target ID Name .......................................................................... 6-28
6.5.6.2 Setting track color of tracked target ...................................................................... 6-30
6.5.7 Setting target for which ground is fixed to a reference target ..................................... 6-31
Page 5
(3) Contents
2 3 4 5 6 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
6.5.8 Operation Test for Target Tracking .............................................................................. 6-33
6.5.8.1 Test Video ............................................................................................................. 6-34
6.5.8.2 [TT Simulator] (Target tracking simulator) ............................................................ 6-35
6.5.8.3 [Gate Display] ....................................................................................................... 6-37
6.5.8.4 Status display ....................................................................................................... 6-39
6.6 Setting and Operating AIS................................................................................................... 6-40
6.6.1 Enabling AIS Function ................................................................................................ 6-40
6.6.2 Activating AIS targets (Activate AIS) ........................................................................... 6-40
6.6.2.1 Manual activation .................................................................................................. 6-40
6.6.2.2 Automatic activation ............................................................................................. 6-41
6.6.3 Deactivating AIS targets .............................................................................................. 6-41
6.6.4 Displaying AIS information .......................................................................................... 6-42
6.6.5 Displaying Target ID No. ............................................................................................. 6-50
6.6.6 Checking and setting AIS target property ................................................................... 6-51
6.6.6.1 Setting track color of AIS target ............................................................................ 6-51
6.6.7 Conditions for deciding AIS target to be lost ............................................................... 6-52
6.7 Alert Display ........................................................................................................................ 6-53
6.7.1 Danger target alarm (CPA/TCPA) ............................................................................... 6-54
6.7.2 Alarm for new target acquired in automatic acquisition guard zone (New target) ...... 6-55
6.7.3 Lost target notification (Lost) ...................................................................................... 6-56
6.7.4 Target Tracking function alarm (TT Data) ................................................................... 6-57
6.7.5 Gyro set notification (Set Gyro) .................................................................................. 6-57
6.8 Track Function ..................................................................................................................... 6-58
6.8.1 Setting the Past position ............................................................................................. 6-58
6.8.2 Setting the other ship's tracks ..................................................................................... 6-58
6.8.2.1 Setting track color ................................................................................................. 6-59
6.8.2.2 Turning on/off other ship's track function .............................................................. 6-59
6.8.2.3 Setting other ship's track colors ............................................................................ 6-59
6.8.2.4 Turning on/off other ship's track display ............................................................... 6-59
6.8.2.5 Setting up the display interval of other ship’s track .............................................. 6-60
6.8.2.6 Clearing other ship's track .................................................................................... 6-60
6.8.2.7 Saving and loading other ship's track data ........................................................... 6-60
6.9 Entering Own Ship's AIS Voyage Data ............................................................................... 6-61
6.10 Editing and Sending AIS Messages .................................................................................... 6-62
6.11 AIS Message Tray ............................................................................................................... 6-65
6.11.1 Displaying the AIS message tray ................................................................................ 6-65
6.11.2 Switching message display ......................................................................................... 6-67
6.11.3 Sending a message in the message tray after editing ................................................ 6-68
6.12 Highlighting TT/AIS Symbols .............................................................................................. 6-69
6.13 Trial Maneuvering ................................................................................................................ 6-71
6.13.1 Outline of Trial Maneuvering ....................................................................................... 6-71
6.13.2 Performing a trial maneuver ....................................................................................... 6-74
Page 6
Contents (4)
6.14 Displaying the TT/AIS Target List ........................................................................................ 6-76
6.14.1 Displaying TT/AIS List ................................................................................................. 6-76
6.14.1.1 Switching between a standard window and an extended window ....................... 6-77
6.14.2 TT List ......................................................................................................................... 6-79
6.14.3 AIS List ........................................................................................................................ 6-80
6.15 Confirming Own Ship's AIS Information .............................................................................. 6-82
6.16 Displaying the Last Lost AIS Target .................................................................................... 6-83
Section 7 True and False Echoes on Display .............................................. 7-1
7.1 Radar Wave with the Horizon ............................................................................................... 7-1
7.2 Intensity Reflected from the Target ....................................................................................... 7-3
7.3 Sea Clutter and Rain/Snow Clutter ....................................................................................... 7-5
7.3.1 Sea clutter ..................................................................................................................... 7-5
7.3.2 Rain and snow clutter ................................................................................................... 7-6
7.3.3 Coping with sea clutter and rain/snow clutter ............................................................... 7-8
7.4 False Echoes ........................................................................................................................ 7-9
7.4.1 Shadow ......................................................................................................................... 7-9
7.4.2 Side lobe effect ............................................................................................................. 7-9
7.4.3 False echo by secondary reflection ............................................................................ 7-10
7.4.4 False echo by multiple reflection ................................................................................ 7-11
7.4.5 Second time echoes ................................................................................................... 7-11
7.4.6 Radar interference ...................................................................................................... 7-12
7.5 Radar Transponder (SART) Screen Display ....................................................................... 7-13
7.6 Display of AIS-SART ........................................................................................................... 7-15
7.6.1 Radar screen display example ................................................................................... 7-15
7.6.2 Numeric data display example .................................................................................... 7-16
Section 8 Functions of the ECDIS (Option) ........................................................... 8-1
8.1 General Flowchart ................................................................................................................. 8-1
8.1.1 Work Flowchart While Sailing ....................................................................................... 8-2
8.2 Starting and Preparing the ECDIS ........................................................................................ 8-3
8.2.1 Powering on and starting .............................................................................................. 8-3
8.2.2 Starting the ECDIS ........................................................................................................ 8-4
8.2.2.1 Starting the ECDIS from the Task Menu ................................................................. 8-4
8.2.2.2 Starting ECDIS from a non-ECDIS task screen ..................................................... 8-5
8.2.3 Entering an ARCS PIN Number (ARCS Only) .............................................................. 8-6
8.3 Moving the Chart ................................................................................................................... 8-7
8.3.1 Moving the chart with the [HOME] button ..................................................................... 8-7
8.3.2 Moving the chart with the cross-hair cursor .................................................................. 8-8
8.3.3 Moving the chart with the hand cursor .......................................................................... 8-9
8.3.4 Switching a chart to be displayed by "My Port List" .................................................... 8-10
8.3.5 Displaying the chart by entering the position .............................................................. 8-11
8.4 Zooming In/Out the Chart.................................................................................................... 8-12
Page 7
(5) Contents
2 3 4 5 6 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
8.4.1 Enlarging a Selected Area (S-57/C-MAP Only) .......................................................... 8-12
8.4.2 Enlarging/reducing a chart with the Zoom function .................................................... 8-14
8.4.2.1 Enlarging/reducing with the [ZOOM IN]/[ZOOM OUT] key on the trackball
operation unit (S-57/C-MAP only)......................................................................... 8-14
8.4.2.2 Enlarging/reducing with the zoom slider (S-57/C-MAP only) ............................... 8-14
8.4.2.3 Enlarging/reducing with the Large/Small buttons (RNC only) .............................. 8-15
8.4.3 Switching between scale and range (S-57/C-MAP only) ............................................ 8-16
8.5 Changing the Object Category (S-57/C-MAP Only)............................................................ 8-17
8.5.1 Switching object display .............................................................................................. 8-18
8.5.2 Customizing object display ......................................................................................... 8-19
8.6 Selecting Motion/Bearing Mode .......................................................................................... 8-21
8.6.1 Setting motion mode ................................................................................................... 8-22
8.6.2 Setting Bearing mode (S-57/C-MAP only) .................................................................. 8-24
8.7 Registering and Displaying My Port List ............................................................................. 8-26
8.7.1 Registering to My Port List .......................................................................................... 8-26
8.7.2 Deleting a port ............................................................................................................. 8-27
8.8 Selecting a S-57 chart ......................................................................................................... 8-28
8.9 Selecting an ARCS chart ..................................................................................................... 8-29
8.9.1 Selecting charts from all .............................................................................................. 8-29
8.9.2 Changing active panels (ARCS only) ......................................................................... 8-30
8.9.3 Changing a low resolution chart (ARCS only) ............................................................ 8-31
8.9.4 Changing a high resolution chart (ARCS only)
............................................................... 8-32
8.9.5 Displaying the note and diagram
(ARCS only)
............................................................ 8-33
8.10 Multi View Display and Wide Range View Window Display of Charts ................................ 8-34
8.10.1 Display of multi view ................................................................................................... 8-35
8.10.1.1 Displaying multi view ............................................................................................ 8-35
8.10.1.2 Multi view operation procedure ............................................................................ 8-37
8.11 Verifying Object Information (Pick Report Function) ........................................................... 8-41
8.11.1 Pick Report of the S-57 chart ...................................................................................... 8-41
8.11.1.1 Displaying a Pick Report of the S-57 chart ........................................................... 8-41
8.11.1.2 Verifying Object Information ................................................................................. 8-43
8.11.1.3 Verifying Chart Information ................................................................................... 8-46
8.11.1.4 Verifying Chart Update History ............................................................................. 8-47
8.11.2 Pick report of the ARCS chart ..................................................................................... 8-48
8.11.3 Manual Update Pick Report ........................................................................................ 8-49
8.11.3.1 Displaying a Manual Update Pick Report ............................................................. 8-49
8.12 Marking the Position of Own Ship with an Event Mark ....................................................... 8-50
8.13 Displaying Radar Images on a Chart by Overlaying ........................................................... 8-51
8.13.1 Turning On/Off overlay display ................................................................................... 8-52
8.13.2 Turning On/Off range ring display ............................................................................... 8-54
8.13.3 Turning On/Off bearing scale ...................................................................................... 8-55
8.13.4 Radar image adjustment ............................................................................................. 8-56
Page 8
Contents (6)
8.14 Setting a true bearing .......................................................................................................... 8-57
8.15 Setting an own ship’s speed ............................................................................................... 8-58
8.15.1 Switching an own ship’s speed sensor ....................................................................... 8-58
8.15.2 Entering the ship’s heading/own ship’s speed manually ............................................ 8-59
Section 9 Route Planning .............................................................................. 9-1
9.1 Overview of the Route Planning Function ............................................................................. 9-2
9.2 Setting Route Display ............................................................................................................ 9-3
9.2.1 Setting [Route] after selecting [View] - [Options] on the menu ..................................... 9-3
9.2.2 Setting [Settings] - [Route] on the menu ....................................................................... 9-5
9.3 Starting and Ending the Route Planning Dialog Box ............................................................ 9-9
9.3.1 Starting the "Route Planning" dialog box ...................................................................... 9-9
9.3.2 Ending the "Route Planning" dialog box ....................................................................... 9-9
9.4 Name and Function of Each Section of the "Route Planning" Dialog Box ......................... 9-10
9.4.1 Route Planning bar ..................................................................................................... 9-10
9.4.2 Route planning tab ...................................................................................................... 9-15
9.5 Saving a Route .................................................................................................................... 9-17
9.6 Planning a Route by Using Table Editing ............................................................................ 9-21
9.6.1 Table editing operation flow ........................................................................................ 9-21
9.6.1.1 Creating a new route file ....................................................................................... 9-21
9.6.1.2 Editing a route ...................................................................................................... 9-22
9.6.2 Creating a new route file by table editing .................................................................... 9-23
9.6.3 Deleting WPT data ...................................................................................................... 9-25
9.6.4 Editing a route by table editing ................................................................................... 9-25
9.6.4.1 Inserting WPT ....................................................................................................... 9-28
9.6.4.2 Deleting WPT ....................................................................................................... 9-28
9.6.4.3 Dividing a leg ........................................................................................................ 9-29
9.6.4.4 Copying the entire route ....................................................................................... 9-29
9.6.4.5 Pasting the route .................................................................................................. 9-30
9.6.4.6 Inserting the other route ....................................................................................... 9-30
9.6.4.7 Insert the same WPT as the last WPT ................................................................. 9-31
9.7 Planning a New Route by Graphic Editing .......................................................................... 9-32
9.7.1 Graphic editing operation flow .................................................................................... 9-32
9.7.1.1 Creating a new route file ....................................................................................... 9-32
9.7.1.2 Editing a route file ................................................................................................. 9-33
9.7.2 Creating a new route file by graphic editing ............................................................... 9-34
9.7.2.1 Creating a route by using EBL/VRM .................................................................... 9-36
9.7.2.2 Creating a route by using the assistant circle function ......................................... 9-38
9.7.3 Editing a route by graphic editing ............................................................................... 9-40
9.7.3.1 Inserting a WPT between WPTs ........................................................................... 9-42
9.7.3.2 Moving a WPT ...................................................................................................... 9-43
9.7.3.3 Changing XTL (cross track limit) .......................................................................... 9-45
9.7.3.4 Adding WPT on the context menu ........................................................................ 9-46
Page 9
(7) Contents
2 3 4 5 6 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
9.7.3.5 Moving WPT on the context menu ....................................................................... 9-47
9.7.3.6 Deleting WPT on the context menu ...................................................................... 9-48
9.7.3.7 Copying and pasting a route on the context menu ............................................... 9-49
9.7.3.8 Rotating a route on the context menu .................................................................. 9-50
9.7.3.9 Moving a route on the context menu .................................................................... 9-51
9.7.3.10 Merging other route on the context menu ............................................................ 9-53
9.7.3.11 Inserting WPT between WPTs on the context menu ............................................ 9-54
9.7.3.12 Dividing a leg on the context menu ...................................................................... 9-55
9.7.3.13 Changing XTL (cross track limit) on the context menu ......................................... 9-56
9.8 Creating an Alternate Route ................................................................................................ 9-58
9.8.1 Creating an alternate route ......................................................................................... 9-60
9.8.2 Saving an alternate route ............................................................................................ 9-61
9.8.2.1 Overwriting without changing the file name .......................................................... 9-61
9.8.2.2 Saving the file by naming ..................................................................................... 9-62
9.9 Checking Route Data .......................................................................................................... 9-63
9.9.1 Checking a route based on the safety standards ....................................................... 9-63
9.9.2 Checking a route based on the limits .......................................................................... 9-66
9.10 Navigation Calculation Function ......................................................................................... 9-68
9.10.1 ROT (Rate of Turn) ..................................................................................................... 9-68
9.10.2 ETA (Estimated Time of Arrival) .................................................................................. 9-68
9.10.3 TTG (Time to Go) ........................................................................................................ 9-68
9.11 Importing/Exporting a Route File ........................................................................................ 9-69
9.11.1 Importing a route file ................................................................................................... 9-69
9.11.2 Exporting a route file ................................................................................................... 9-70
9.12 Error Messages that are Displayed when a Route is Created ............................................ 9-71
Section 10 Route Monitoring ........................................................................ 10-1
10.1 Route Monitoring ................................................................................................................. 10-1
10.1.1 Starting route monitoring ............................................................................................. 10-1
10.1.2 Ending route monitoring .............................................................................................. 10-2
10.2 Selecting and Deleting Route Files ..................................................................................... 10-3
10.2.1 Selecting a route to be displayed ................................................................................ 10-3
10.2.2 Deleting a route file ..................................................................................................... 10-4
10.3 Voyage Information (Voyage Monitoring Information) Dialog Box ...................................... 10-5
10.4 Voyage Calculation Dialog Box ......................................................................................... 10-10
10.4.1 Calculating a schedule .............................................................................................. 10-12
10.4.2 Calculating a distance ............................................................................................... 10-13
10.4.3 Example of distance calculation ............................................................................... 10-15
10.5 Comparing the Data between the Planned Route and the Actual Route .......................... 10-17
10.6 Verifying Detail Information of WPT .................................................................................. 10-19
Section 11 Monitoring a Dragging Anchor .................................................. 11-1
11.1 Setting a Dragging Anchor Monitoring Area ........................................................................ 11-2
Page 10
Contents (8)
11.1.1 Setting a dragging anchor monitoring circle ............................................................... 11-2
11.1.2 Setting a dragging anchor monitoring polygon ........................................................... 11-3
11.2 Starting and Ending Dragging Anchor Monitoring ............................................................... 11-5
11.2.1 Starting dragging anchor monitoring ........................................................................... 11-5
11.2.2 Ending dragging anchor monitoring ............................................................................ 11-6
11.3 Moving/Editing/Deleting a Dragging Anchor Monitoring Area on the Chart ........................ 11-7
11.3.1 Moving a dragging anchor monitoring circle on the chart ........................................... 11-7
11.3.2 Moving a dragging anchor monitoring circle on the context menu ............................. 11-8
11.3.3 Moving a dragging anchor monitoring polygon on the chart ...................................... 11-8
11.3.4 Moving a dragging anchor monitoring ploygon on the context menu ......................... 11-8
11.3.5 Changing a size of a dragging anchor monitoring circle on the chart ........................ 11-9
11.3.6 Changing a size of a dragging anchor monitoring circle on the context menu ......... 11-10
11.3.7 Changing a shape of a dragging anchor monitoring polygon on the chart ............... 11-10
11.3.8 Changing a shape of a dragging anchor monitoring polygon on the context menu .. 11-11
Section 12 Automatic Sailing (Option) ................................................................. 12-1
12.1 Flow of Starting Automatic Sailing ....................................................................................... 12-2
12.2 Selecting a Route ................................................................................................................ 12-6
12.2.1 Using the existing planned route ................................................................................ 12-6
12.2.2 Creating a new route .................................................................................................. 12-8
12.3 Selecting a Waypoint at which Automatic Sailing Starts ................................................... 12-10
12.4 Starting Automatic Sailing ................................................................................................. 12-12
12.5 Stopping Automatic Sailing ............................................................................................... 12-14
12.6 Alerts at Automatic Sailing ................................................................................................ 12-15
Section 13
Operating a Chart (option)
.............................................................. 13-1
13.1 Updating a Chart Manually.................................................................................................. 13-3
13.2 Displaying/Searching an S-57 Chart [Select S-57 Chart] ................................................... 13-4
13.2.1 Displaying a chart ....................................................................................................... 13-4
13.2.2 Search a chart ............................................................................................................. 13-5
13.2.2.1 Searching the position that is clicked on by the cursor ........................................ 13-5
13.2.2.2 Searching by using a chart name ......................................................................... 13-6
13.3 Displaying a Chart by Inputting a Position .......................................................................... 13-7
13.4 Confirming/Accepting an S-57 Updated Chart .................................................................... 13-8
13.5 Displaying a Date-dependent Object .................................................................................. 13-9
13.6 Displaying a Chart Boundary ............................................................................................ 13-10
13.6.1 Setting a boundary to be displayed on the chart ...................................................... 13-10
13.6.2 Displaying chart information ..................................................................................... 13-11
13.7 Confirming Temporary/Preliminary Information of an ARCS Chart (ARCS Only) ............. 13-12
13.8 Adjusting an ARCS Chart Position (ARCS Only) .............................................................. 13-13
13.8.1 Offsetting an ARCS chart .......................................................................................... 13-13
13.8.2 Transforming a geodetic datum of an ARCS chart to WGS-84 ................................ 13-15
Page 11
(9) Contents
2 3 4 5 6 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
13.9 Displaying a Chart Abbreviation List ................................................................................. 13-20
13.10 Maintaining a Chart ........................................................................................................... 13-21
Section 14 Creating a User Map/ Updating a Chart Manually .................... 14-1
14.1 Creating/Editing a User Map ............................................................................................... 14-3
14.1.1 Display the "User Map" menu. .................................................................................... 14-4
14.1.2 Display the File Operation submenu ........................................................................... 14-5
14.1.2.1 "File Operation" dialog box ................................................................................... 14-5
14.1.3 Creating a new user map ............................................................................................ 14-7
14.1.4 Editing the existing user map ...................................................................................... 14-8
14.1.4.1 Editing the user map that is currently displayed ................................................... 14-8
14.1.5 Displaying a user map ................................................................................................ 14-9
14.1.6 Operating a user map file ......................................................................................... 14-10
14.1.6.1 Deleting a user map file ...................................................................................... 14-10
14.1.6.2 Copying a user map file ...................................................................................... 14-10
14.1.6.3 Importing a user map file .................................................................................... 14-11
14.1.6.4 Exporting a user map file .................................................................................... 14-11
14.1.6.5 Merging multiple user map files .......................................................................... 14-12
14.1.6.6 Performing geodetic datum conversion .............................................................. 14-13
14.2 Using Map Creation Tools (User Map Creation/Editing) ................................................... 14-14
14.2.1 User map information bar ......................................................................................... 14-14
14.2.1.1 Displaying a user map information bar ............................................................... 14-14
14.2.2 Drawing toolbar ......................................................................................................... 14-15
14.2.3 Selecting an object type ............................................................................................ 14-16
14.2.3.1 Using a user map object ..................................................................................... 14-17
14.2.4 Selecting a color of an object .................................................................................... 14-18
14.2.5 Creating an object in the EBL/VRM mode ................................................................ 14-19
14.2.6 Creating an object by specifying latitude and longitude ........................................... 14-19
14.2.6.1 Creating an object of symbol/circle/ellipse/arc/arrow/text .................................. 14-20
14.2.6.2 Creating an object of simple line/polygon/highlight ............................................ 14-20
14.2.7 Deleting an object ..................................................................................................... 14-20
14.2.8 Object property dialog box ........................................................................................ 14-21
14.2.8.1 Selecting an object ............................................................................................. 14-21
14.2.8.2 Setting a comment .............................................................................................. 14-22
14.2.9 Changing an object display scale range ................................................................... 14-23
14.2.10 Moving an object ....................................................................................................... 14-23
14.3 Updating a Chart Manually (ECDIS Screen Only) ............................................................ 14-25
14.3.1 Displaying the Manual Update submenu .................................................................. 14-26
14.3.2 Selecting a chart to be updated ................................................................................ 14-27
14.3.2.1 Searching the position that is clicked on with the cursor .................................... 14-28
14.3.2.2 Searching a chart with the chart name ............................................................... 14-28
14.3.3 Updating a chart manually ........................................................................................ 14-28
14.3.4 Displaying the selected chart only ............................................................................ 14-29
Page 12
Contents (10)
14.3.5 Displaying the object/redisplaying the hidden object ................................................ 14-29
14.4 How to Use the Map Creation Tools (for Manual Update) ................................................ 14-30
14.4.1 Deleting or hiding an object ...................................................................................... 14-30
14.4.2 Selecting an object type ............................................................................................ 14-31
14.5 Creating an Object ............................................................................................................ 14-32
14.5.1 Creating a symbol object (Symbol) ........................................................................... 14-33
14.5.1.1 Creating an object by specifying the latitude and longitude ............................... 14-33
14.5.1.2 Creating an object with EBL/VRM operation ...................................................... 14-34
14.5.2 Creating a simple line and a Warning line (Line object) ........................................... 14-35
14.5.2.1 Creating a vertex by entering the position .......................................................... 14-38
14.5.2.2 Creating an object with EBL/VRM operation ...................................................... 14-38
14.5.3 Creating a circle, ellipse, and an arc (Line object) .................................................... 14-40
14.5.3.1 Creating an object by specifying a position for the center and size of the
object .................................................................................................................. 14-42
14.5.4 Creating a polygon and a Warning area (Area object) ............................................. 14-43
14.5.4.1 Creating a vertex by entering the position .......................................................... 14-45
14.5.4.2 Creating an object with EBL/VRM operation ...................................................... 14-46
14.5.5 Creating circle, ellipse, and fan areas (Area object) ................................................. 14-47
14.5.5.1 Creating an object by specifying the center position and the object size ........... 14-49
14.5.6 Creating a text (Text object) ...................................................................................... 14-50
14.5.6.1 Creating a text by specifying the latitude and longitude ..................................... 14-51
14.5.6.2 Creating a text with EBL/VRM operation ............................................................ 14-51
14.5.6.3 Editing a text ....................................................................................................... 14-52
14.5.6.4 Editing a template ............................................................................................... 14-52
14.5.6.5 Changing a text angle ......................................................................................... 14-54
14.5.7 Creating an arrow (Line object) ................................................................................ 14-55
14.5.7.1 Creating an object by specifying the starting point/ending point position
coordinates ......................................................................................................... 14-56
14.5.7.2 Drawing an object with EBL/VRM operation ...................................................... 14-57
14.5.8 Creating Mariner's Mark/Line drawing objects (ECDIS screen only) ........................ 14-58
14.5.8.1 Information mark ................................................................................................. 14-58
14.5.8.2 Clearing line ........................................................................................................ 14-60
14.5.8.3 Tidal Stream mark ............................................................................................... 14-63
14.5.8.4 Highlighted display ............................................................................................. 14-65
14.6 Collective Deletion of Objects [Delete by Type/Color] ...................................................... 14-71
14.7 Managing/Editing Objects [Mark Line/List] ........................................................................ 14-72
14.7.1 Displaying the "Mark/Line List" dialog box ................................................................ 14-72
14.7.2 Displaying a user map list ......................................................................................... 14-73
14.7.2.1 Displaying an object on a chart .......................................................................... 14-73
14.7.2.2 Deleting an object ............................................................................................... 14-74
14.7.3 Displaying a Mariner's Mark/Line List (ECDIS screen only) ..................................... 14-74
14.7.3.1 Displaying an object on a chart .......................................................................... 14-74
14.7.3.2 Deleting an object ............................................................................................... 14-74
Page 13
(11) Contents
2 3 4 5 6 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
14.7.3.3 Deleting objects collectively from an object list .................................................. 14-75
14.7.4 Displaying a manual update list (ECDIS screen only) .............................................. 14-75
14.7.4.1 Displaying an object on a chart .......................................................................... 14-75
14.7.4.2 Hiding an object .................................................................................................. 14-76
14.7.4.3 Redisplaying an object ....................................................................................... 14-76
Section 15 Logbook ....................................................................................... 15-1
15.1 Browsing a Logbook ............................................................................................................ 15-1
Searching an event based on the date ............................................................................... 15-2
Sorting events ..................................................................................................................... 15-2
Switching the event groups ................................................................................................. 15-2
15.1.1 Event detail information .............................................................................................. 15-3
Detail information that can be edited .................................................................................. 15-3
15.2 Editing a Logbook ............................................................................................................... 15-5
15.2.1 Adding an event .......................................................................................................... 15-5
Deleting an event mark ....................................................................................................... 15-5
15.2.2 Editing event detail information ................................................................................... 15-6
15.3 Outputting Event Data ......................................................................................................... 15-7
15.3.1 Outputting a logbook as a file ..................................................................................... 15-7
Section 16 Setting up Screen View .............................................................. 16-1
16.1 Setting Chart Display Mode (Multi View Mode) (ECDIS only) ............................................ 16-3
16.1.1 Setting Multi-Screen.................................................................................................... 16-3
16.2 Setting Screen Display Options .......................................................................................... 16-4
16.2.1 Setting up the display of Own Ship symbol ................................................................ 16-7
16.2.2 Setting up the display of ECDIS own ship’s track ..................................................... 16-11
16.2.3 Setting up the display of Route Monitoring ............................................................... 16-13
16.2.4 Setting up the display of User Map ........................................................................... 16-15
16.2.5 Setting up the display of Mariner's Mark/Line ........................................................... 16-17
16.2.6 Setting up Radar Overlay and Transparency of Echo/Trails .................................... 16-18
16.2.7 Setting up the display of TT/AIS Target .................................................................... 16-19
16.2.8 Setting up the display of Other Ship’s Track ............................................................. 16-22
16.2.9 Setting up the display of Chart Common .................................................................. 16-27
16.2.10 Setting up the display of RADAR Chart .................................................................... 16-35
16.2.11 Setting up the display of ECDIS Chart...................................................................... 16-37
16.2.12 Setting up AIO display .............................................................................................. 16-43
16.2.13 Setting up the display of range/bearing measurement function ............................... 16-44
16.2.14 Setting up the display of Unit of Setting Value .......................................................... 16-45
16.2.15 Setting up display of Own Ship Track Control, display format of Own Ship/Cursor
Position and display of Sub-Information dialog ........................................................ 16-47
16.2.16 Setting up the Water Depth display .......................................................................... 16-48
16.2.17 Setting up the Rudder graph ..................................................................................... 16-49
16.2.18 Setting up the Gyro/Rudder graph ............................................................................ 16-50
Page 14
Contents (12)
16.2.19 Setting up the Engine Graph .................................................................................... 16-51
16.2.20 Setting up the graph range of the ROT slide bar ...................................................... 16-52
Section 17 Setting up Alerts ......................................................................... 17-1
17.1 Selecting Setting Items ....................................................................................................... 17-1
17.1.1 Displaying the "Alert" dialog box ................................................................................. 17-1
17.1.2 Selecting a setting item ............................................................................................... 17-2
17.2 Collision Avoidance Alert Generation Conditions ................................................................ 17-4
17.2.1 Setting the CPA/TCPA limit values ............................................................................. 17-4
17.2.2 Setting the status of the AIS target that is targeted for lost warning ........................... 17-5
17.3 New Target Alarm Generation Conditions ........................................................................... 17-6
17.3.1 Switching AZ1/AZ2 to enable/disable ......................................................................... 17-7
17.3.1.1 Enabling AZ1 or AZ2 ............................................................................................. 17-7
17.3.1.2 Disabling AZ1 or AZ2 ............................................................................................ 17-7
17.4 Depth/Safety Contour Alert Generation Conditions ............................................................ 17-8
17.5 Setting Up Vector/Sector ................................................................................................... 17-10
17.5.1 Switching to enable/disable a danger detection vector/sector ................................. 17-11
17.5.2 Setting up the size of a danger detection vector ...................................................... 17-11
17.5.3 Setting up the size of a danger detection sector ...................................................... 17-11
17.6 Area Warning Generation Conditions ............................................................................... 17-12
17.7 Track Control Alert Generation Conditions ....................................................................... 17-13
17.8 Position Integrity Alert Generation Conditions .................................................................. 17-14
17.8.1 Setting up the generation condition of the Position monitor warning ....................... 17-14
17.8.2 Setting up the HDOP exceeded caution generation condition ................................. 17-15
17.9 Setting up Alert Processing ............................................................................................... 17-16
17.10 Setting Up the Alert Timer ................................................................................................. 17-17
17.10.1 Setting up the timer ................................................................................................... 17-17
17.10.2 Setting up the time .................................................................................................... 17-17
Section 18 Setting up the Operation Mode .................................................. 18-1
18.1 Basic Operation of the "Settings" Dialog Box ..................................................................... 18-1
18.2 Basic Settings for Radar Signal Processing ....................................................................... 18-4
18.3 Setting Radar Signal Processing ........................................................................................ 18-6
18.4 Presetting Each Observation Scene ................................................................................... 18-7
18.5 Setting Other Ship’s Radar Trails ...................................................................................... 18-13
18.6 Setting Radar Antennas .................................................................................................... 18-14
18.6.1 Setting radar antennas ............................................................................................. 18-14
18.7 Setting Associations .......................................................................................................... 18-15
18.8 Setting Own Ship's Dynamic Trait ..................................................................................... 18-17
18.9 Setting Operation Tests ..................................................................................................... 18-18
18.10 Setting AIS Filters .............................................................................................................. 18-20
18.11 Setting the Target Track Function to ON/OFF ................................................................... 18-22
Page 15
(13) Contents
2 3 4 5 6 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
18.12 Setting Parameter Values at Route Plan Creation ............................................................ 18-23
18.13 Setting Automatic Sailing Parameter Values ..................................................................... 18-25
18.14 Setting the Temporary Route Setting Values .................................................................... 18-28
18.15 Setting Chart Operation .................................................................................................... 18-29
18.16 Setting Logbook ................................................................................................................ 18-32
18.17 Setting Navigation Equipment ........................................................................................... 18-35
18.18 Setting Colors and Brightness .......................................................................................... 18-36
18.19 Setting Sounds .................................................................................................................. 18-40
18.20 Setting Key Assignment .................................................................................................... 18-43
18.21 Setting Preferences Information ....................................................................................... 18-46
18.22 Setting Screen Capture ..................................................................................................... 18-55
Page 16
Contents (14)
Page 17
5-1 Section 5 Basic Operation of the Radar
1
2 3 4 5 5 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
APP A
APP B
Section 5 Basic Operation of the
Radar
Use the radar as your navigation aid.
Final decision on the ship operation must be made by the ship operator himself.
If you depend entirely on the
radar information for the final decision on the ship
operation, such an accident as collision and stranding may occur.
If momentary power interruption has occurred on the ship during the radar operation,
the image may distort or may not appear. If this occurs, turn on the power again.
5.1 Overview Flowchart
• Do no put anything on the operation section.
In particular, if a hot object is placed on the operation section, deformation is likely
to occur.
• Do not allow a heavy impact to be applied to the operation section, trackball or
dial.
A trouble may occur.
Page 18
Section 5 Basic Operation of the Radar 5-2
Power ON this system and start the radar.
Adjust reception gain, sea clutter and rain/snow
clutter so that the observation range as well as the
target display become the clearest.
Acquire data, and then measure the range and
bearing of the target.
Exit the operation of the Radar.
Refer to "5.2.1 Powering on and
starting".
Refer to "5.3 Observation Environment
and Image Adjustment".
Refer to "5.4 General Radar Operation".
Refer to "5.2.2 Exiting radar operation".
Page 19
5-3 Section 5 Basic Operation of the Radar
1
2 3 4 5 5 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
APP A
APP B
5.2 Starting and Shutting Down the Radar
5.2.1 Powering on and starting
Note
• Wait for about 2 seconds before turning on the power again.
• Immediately after the radar is installed, at start of the system after it has not been used for a
long time, or after the magnetron is replaced, preheat the equipment in the standby state for 20
to 30 minutes before setting it into the transmit state.
If the preheating time is short, the magnetron causes sparks, resulting in its unstable oscillation.
• Start transmission on a short pulse range and change the range to the long pulse ranges in
turn. If the transmission is unstable in the meantime, immediately place the system back into
the standby state and maintain it in the standby state for 5 to 10 minutes before restarting the
operation. Repeat these steps until the operation are stabilized.
1 Check that the ship’s mains are turned on.
2 Press the Power button on the operation unit.
This equipment starts and Task Menu appears on the screen.
Page 20
Section 5 Basic Operation of the Radar 5-4
3 Click on the [Collision Avoidance (RADAR)] button on Task Menu.
The RADAR screen appears.
The preheating time is displayed at the center of the screen.
Preheating time
Page 21
5-5 Section 5 Basic Operation of the Radar
1
2 3 4 5 5 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
APP A
APP B
When the magnetron radar antenna is connected, “Preheat” is displayed on the Standby/Send
switching button.
4 Wait until preheating is complete.
When the preheating time expires, the preheating time display disappears, and the display of
the Standby/Transmit switch button changes from "Preheat" to "Standby".
5 Click on the Standby/Transmit switch button.
Radar transmission starts and the radar antenna rotates.
The display of the Standby/Transmit switch button changes from "Standby" to "Transmit".
Note
Even if the Standby/Transmit switch button is clicked on while "Preheat" is being displayed, radar
transmission cannot be performed.
Memo
When the “Preheat” display is held down (5
seconds or longer), the display is switched to
“Standby”.
Page 22
Section 5 Basic Operation of the Radar 5-6
5.2.2 Exiting radar operation
1 Click on the Standby/Transmit switch button in Radar system information.
Radar transmission stops and the rotation of the radar antenna stops.
The display of the Standby/Transmit switch button changes from "Transmit" to "Standby".
Memo
If observation using the radar is being scheduled within a comparably short period of time,
keep this state. Observation can be started immediately by just
clicking on the
Standby/Transmit switch button.
2 Press the Power button on the operation unit.
The power to this equipment is turned OFF.
Before starting maintenance, turn off power. Cut off all the power
supplies to the equipment. Some equipment components can carry electrical current even after the
power switch is turned off, and conducting maintenance work may result
in electric shock, equipment failure, or accidents.
When turning off the power supply, do not hold down the power button of
the operation unit. Otherwise, a trouble may occur due to termination failure.
Page 23
5-7 Section 5 Basic Operation of the Radar
1
2 3 4 5 5 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
APP A
APP B
5.3 Observation Environment and Image Adjustment
5.3.1 Adjusting screen brightness
1 Adjust the screen brightness.
For the details of the adjustment, refer to "3.9 Adjusting the Brightness of the Screen and
Operation Unit".
In consideration of the ambient brightness, adjust the brightness of the display that is high
enough to easily observe the radar display but does not glare.
5.3.2 Changing the observation range
1 Click on the Range Scale button in Presentation and mode information, and then
select Range from the pop-up menu.
[Points on adjustments]
Increasing the observation range will enable a wider range to be observed.
However, a video image is small and the ability to detect targets near own ship decreases.
Therefore, when observing the vicinity of own ship, use the smaller observation range.
Decreasing the observation range will enable the vicinity of own ship to be enlarged. However,
caution must be taken because video images of the area beyond the observation range cannot
be displayed.
Range Scale button
Page 24
Section 5 Basic Operation of the Radar 5-8
Since the image within the previous observation range is displayed by
expanding/contracting for the period from immediately after switching of the
observation range from the next image updating, do not use
this image for
navigation.
If this image is used for navigation, an accident may occur.
Note
An observation range under which the own ship display positon and the antenna position exceeds
the area 66% of the screen radius cannot be selected.
Page 25
5-9 Section 5 Basic Operation of the Radar
1
2 3 4 5 5 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
APP A
APP B
5.3.3 Adjusting tune
Normally, use the automatic tune mode.
If you use the manual tuning mode, an accident may be caused by
fluctuation of transmission and reception. Use the manual tune mode only when best tuning is not possible in the
automatic tune mode due to deterioration of magnetron.
This equipment has the automatic tuning mode that performs tuning of the transmission frequency and
the reception frequency by automatic control, and the manual tuning mode in which the user performs
tuning. Normally use the automatic tune mode. Only when the best tuning is not possible by the
automatic tune mode due to the deterioration of magnetron, use the manual tune mode.
The tuning mode currently being used is displayed on the Tuning Mode button in Radar system
information.
Note
This function is effective when a magnetron radar antenna is connected.
When using the automatic tune mode
1
Click on the tune mode button.
[AUTO] (automatic) is displayed on the tune mode button.
Whenever the button is clicked on, the mode is switched between [AUTO] (automatic) and
[MAN] (manual).
Tuning Mode button
Page 26
Section 5 Basic Operation of the Radar 5-10
Using the manual tune mode
1
Click on the tune mode button.
[MAN] (manual) is displayed on the tune mode button.
Each time this button is clicked on, the display switches between [AUTO] (automatic) and
[MAN] (manual).
2 Move the fine tuning slider to the left and right sides.
The tuning status is displayed on the tuning bar according to the movement of the fine tuning
slider.
Make adjustments so that the display on the tuning bar indicates the maximum (the state in
which the tuning bar is positioned at the most right).
5.3.4 Adjusting gain
Be sure to always adjust for the best gain.
If the gain is too high, undesired signals including receiver noise and false echoes increase resulting in reduction of visibility of targets.
Otherwise, accidents may result.
On the contrary, if the gain is too low, targets including ships and dangerous objects may not be clearly indicated.
Adjust the gain of the radar.
Memo
Set the o
ptimum gain when making adjustments, giving consideration to the setting described in
"5.3.7 Adjusting to optimal images (Selection of observation scenes)".
This bar indicates the tuning state.
Tuning indication peak line
Indicates the maximum point of tuning.
Fine tuning slider
Page 27
5-11 Section 5 Basic Operation of the Radar
1
2 3 4 5 5 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
APP A
APP B
1 Drag the [Gain] (reception gain adjustment) slider dial in Radar signal information,
turn the trackball, and set up reception gain.
Moving the slider to the right increases gain.
Moving the slider to the left decreases gain.
The current reception gain level is indicated by the bar and a numeric value.
[Points on adjustments]
As reception gain is increased, the range in which radar images can be observed widens; however, if
gain is increased too high, receiver noise, false echoes and other undesired signals will increase on
the screen, lowering the visibility of targets.
Also, it gets easier to see the screen display if gain is decreased to observe cluttered targets and close
range, but be careful not to overlook small targets.
Memo
If the optimal setting value was lost, it is recommended to reset to
the initial value and tune up again.
The initial setting value is indicated as shown in the figure at right.
Initial setting value
[Gain] (reception gain adjustment) slider
Current reception gain
Page 28
Section 5 Basic Operation of the Radar 5-12
5.3.5 Rejecting sea clutter (Sea)
Never set the sea clutter suppression function before rejecting all the sea
clutters at close range. Detection of not only echoes from the wave and
so on but also targets such as other ships or dangerous objects may be suppressed.
When using the sea clutter suppression function, make sure to choose
the most appropriate setting for suppression.
Memo
Remove images by sea clutter by using the sea clutter suppression function.
When using the sea clutter suppression function, make the optimum setting, giving considerating
to the setting described in "5.3.7 Adjusting to optimal images (Selection of observation scenes)".
1 Drag the [Sea] (sea clutter adjustment) slider dial in Radar signal information, turn the
trackball, and adjust the amount of images by sea clutter displayed on the screen so
as to make display easy to observe.
Moving the slider to the right decreases the amount of images by sea clutter.
Moving the slider to the left increases the amount of images by sea clutter.
The current level of sea clutter suppression is indicated by the bar and a numeric value.
[Points on adjustments]
The sea clutter suppression function decreases the amount of images by sea clutter by lowering
reception gain at close range. When reception gain is lowered, the effectiveness of sea clutter
suppression increases; however, if excessive effect is applied, please note that targets having weak
signal strength such as buoys and small ships will disappear.
[Sea] (sea clutter adjustment) slider
Current level of sea clutter suppression
Page 29
5-13 Section 5 Basic Operation of the Radar
1
2 3 4 5 5 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
APP A
APP B
Memo
If the optimal setting value was lost, it is recommended to reset to
the initial value and tune up again.
The initial setting value is indicated as shown in the figure at right.
Using the function of automatic sea clutter suppression mode
The sea clutter suppression in accordance with the intensity of sea clutter is possible. Use this mode
when the sea clutter's intensity differs according to directional orientation.
1 Click on the Automatic Sea Clutter Suppression button.
[AUTO] (automatic) is displayed on the automatic sea clutter suppression button.
Each time this button is clicked on, the display switches between [AUTO] (automatic) and
[MAN] (manual).
2 Drag the sea clutter adjustment slider dial, turn the trackball, and adjust the amount of
images by sea clutter displayed on the screen.
Even while automatic sea clutter is being suppressed, the amount of images can be
fine-adjusted manually.
Canceling automatic sea clutter suppression
1
Click on the Automatic Sea Clutter Suppression button.
[MAN] (manual) is displayed on the automatic sea clutter suppression button.
Each time this button is clicked on, the display switches between [AUTO] (automatic) and
[MAN] (manual).
Initial setting value
Auto Sea Clutter Suppression button
Page 30
Section 5 Basic Operation of the Radar 5-14
5.3.6 Rejecting rain/snow clutter
Never set the rain/snow clutter suppression function too high.
Detection of not only echoes from the rain or snow but also images targets such as other ships or dangerous objects may be suppressed.
When using the rain/snow clutter suppression function, make sure to
choose the most appropriate setting for suppression.
Memo
Remove images by rain/snow clutter by using the sea clutter suppression function.
When using the rain/snow clutter suppression function, make the optimum setting giving
considerating to the setting described in "5.3.7 Adjusting
to optimal images (Selection of
observation scenes)".
1 Drag the [Rain] rain/snow clutter adjustment slider dial in Radar signal information,
turn the trackball, and adjust the amount of images by rain/snow clutter displayed on
the screen so as to make display easy to observe.
[Rain] (rain/snow clutter adjustment) slider
Page 31
5-15 Section 5 Basic Operation of the Radar
1
2 3 4 5 5 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
APP A
APP B
Moving the slider to the right decreases the amount of images by rain/snow clutter.
Moving the slider to the left increases the amount of images by rain/snow clutter.
The current level of rain/snow clutter suppression is indicated by the bar and a numeric value.
[Points on adjustments]
When the amount of images by rain/snow clutter is decreased, the outlines of targets hidden by images
of rain/snow will appear, but please note that small targets may be missed. Since this can also reduce
sea clutter, it is effective to use it together with the sea clutter rejection function.
Normally, set the level of rain/snow clutter suppression to 0.
Memo
If the optimal setting value was lost, it is recommended to reset to
the initial value and tune up again.
The initial setting value is indicated as shown in the figure at right.
Using the automatic rain/snow clutter suppression mode
The rain/snow clutter suppression in accordance with the intensity of rain/snow clutter is possible. Use
this mode when the rain/snow clutter's intensity differs according to directional orientation.
1 Click on the Automatic Rain/Snow Clutter Suppression button.
[AUTO] (automatic) is displayed on the automatic rain/snow clutter suppression
button.
Each time this button is clicked on, the display switches between [AUTO] (automatic) and
[MAN] (manual).
2 Click the left mouse button of the button on the [Rain
]
(rain/snow clutter adjustment)
slider, drag it with the trackball, and adjust the volume of the echo created by
rain/snow clutter that is displayed on the screen.
Even while auto rain/snow clutter is being suppressed, the amount of images can be
fine-adjusted manually.
Initial setting value
Current level of rain/snow clutter suppression
Auto Rain/Snow Clutter Suppression button
Page 32
Section 5 Basic Operation of the Radar 5-16
Canceling automatic rain/snow clutter suppression
1
Click on the Automatic Rain/Snow Clutter Suppression button.
[MAN] (manual) is displayed on the automatic rain/snow clutter suppression button.
Each time this button is clicked on, the display switches between [AUTO] (automatic) and
[MAN] (manual).
5.3.7 Adjusting to optimal images (Selection of observation scenes)
To obtain optimal images, it is necessary to understand the features of radar signal processing settings
and perform adjustment according to the sea condition. When adjusting all setting values manually,
such adjustment may sometimes difficult even for experienced operators.
Thus, signal processing settings suitable for general usage are preset in the observation scene
selection function at the time of factory shipment. In many cases, optimal images can be obtained
quickly by selecting the observation scene corresponding to the current sea condition.
1 Click on the Observation Scene Selection button in Radar signal information.
The "Observation Scene Selection" dialog is displayed.
Observation Scene Selection button
Page 33
5-17 Section 5 Basic Operation of the Radar
1
2 3 4 5 5 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
APP A
APP B
2 Select the observation scene corresponding to the current sea condition
Refer to the following table about the definitions of observation scene.
Observation
Scene
Definition
Standard
Standard
Coast
Coastal navigation
Use this scene to monitor a relatively short range, for example, bays and coasts
where many boats and ships are running. (Importance is attached to resolution.)
Open-sea
Open-sea navigation
Use this scene to monitor a relatively long range, for example, the open-sea.
(Importance is attached to long range gain)
Fishnet
Fishnet
Use this scene to detect small targets such as fishnets of round haul netters hidden by sea clutter returns. (Importance is attached to sea clutter suppression, and gain to
moving targets lowers.)
Storm
Storm
Use this scene when many rain/snow clutters or sea clutter are detected in stormy weather. (Importance is attached to rain/snow clutter and sea clutter suppression,
and gain slightly lowers.)
Calm
Calm Use this scene when only a few rain/snow clutter or sea clutter are detected.
Rain
Rain
Use this scene when sea clutter is not strong but rain/snow clutter is strong.
(Importance is attached to rain/snow clutter suppression, and gain slightly lowers.)
Page 34
Section 5 Basic Operation of the Radar 5-18
Observation
Scene
Definition
Bird
Bird Use this scene to detect a flock of sea birds.
Long
Long distance detection Use this scene to monitor utmost distances in the broad ocean.
Buoy
Buoy
Use this scene to detect small targets such as radio buoys outside of sea clutter.
(Targets having low detection probability are displayed.)
User1
User 1 General scene used when the nine scenes above are not applicable.
User2
User 2 General scene used when the nine scenes above are not applicable.
3 Adjust [Gain], [Sea] and [Rain] as necessary.
Note
When the setting value among the observation scene is changed from the initial value, underline is
displayed for the observation scene selection button and a button corresponding to the "Selection"
(observation scene selection) dialog is displayed.
Memo
If the optimal setting value was lost, it is recommended to reset to
the initial value and tune up again.
The initial setting value is indicated as shown in the figure at right.
Initial setting value
Page 35
5-19 Section 5 Basic Operation of the Radar
1
2 3 4 5 5 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
APP A
APP B
5.4 General Radar Operation
5.4.1 Interference Rejection (IR Function)
By setting IR (Interference Rejection) function, Interference by other radars is rejected.
Note
To observe the radar beacon and the SART signal, IR processing may occasionally suppress
these images, so set IR to Off (interference rejection function OFF).
1 Click on the RADAR Signal Processing Setting button in Radar signal information.
The RADAR Process dialog box appears.
2 Click on [IR] and then select the interference rejection level from the list.
Setting items
Functions and effects
[Off]
Sets the IR function to Off.
[IR Low]
Sets the IR level to the low level.
[IR Middle]
Sets the IR level to the middle level.
[IR High]
Sets the IR level to the high level.
[Points on setting]
When a high interference rejection level is selected, the radar’s ability of detecting small targets such
as buoys and small boats is lower.
In general, [IR Low] should be selected.
Radar signal processing setting button
Page 36
Section 5 Basic Operation of the Radar 5-20
5.4.2 Changing the transmitter pulse length
1 Click on the Transmitter Pulse Length switch button in Radar signal information.
Each time this button is clicked on, the transmitter pulse length changes.
Transmitter
pulse length
Functions and effects
Recommended condition
for selection
[SP] The transmitter pulse becomes shorter, and the
range resolution improves.
The effect of suppressing sea clutter and rain/snow
clutter improves.
In bays/harbors where targets are densely crowded Rough sea state due to torrential rain or stormy weather
[MP]
The normal transmitter pulse length is set. Both range resolution and gain are appropriately
set.
General navigation
[LP] The transmitter pulse becomes longer, and gain
improves.
Small targets are zoomed and are easy to observe. When the sea state is bad, detection performance
decreases.
Detection of small targets in good weather conditions
Memo
Usable transmitter pulse length differs according to the type of radar antenna being used and the
observation range being used.
Transmitter pulse length switch button.
Example: [MP1] → [MP2] → [LP1] → [LP2]
Page 37
5-21 Section 5 Basic Operation of the Radar
1
2 3 4 5 5 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
APP A
APP B
5.4.3 Enhancing targets
This function enlarges the display sizes of images to enhance targets.
1 Click on the RADAR Signal Processing Setting button in Radar system information.
The “RADAR Process” dialog box appears.
2 Select the target enhancement level from the list in [Target Enhance].
Setting items Functions and effects
Recommended use
condition
[ENH Off] Sets the target enhancement function to OFF. Set this function to Off when
resolution is particularly
necessary.
[ENH Level1] Enhances the radar echo by 1 level in the vertical
and horizontal directions of the screen.
Normal navigation
[ENH Level2] Enhances the radar echo by 2 levels in the vertical
and horizontal directions of the screen.
Enhance the visibility of the
radar image
[ENH Level3] Enhances the radar echo by 3 levels in the vertical
and horizontal directions of the screen.
Detect small targets such
as buoys
[Setting points]
When [ENH Level3] is selected, sea clutter and rain/snow clutter are apt to be enlarged. To use,
suppress images of sea clutter and rain/snow clutter using the [Sea] (sea clutter adjustment) slider and
the [Rain] (rain/snow clutter adjustment) slider.
In general, [ENH Level1] or [ENH Level2] should be selected.
Radar signal processing setting button
Page 38
Section 5 Basic Operation of the Radar 5-22
5.4.4 Using video processing (Echo Process)
This function reduces undesirable noise and enhances targets.
Note
• When viewing a radar beacon, SART signal, or fast moving target on the radar display, select
[Process Off] (video process off).
• If video processing mode is set to [CORREL], a high speed target is less-visible .
1 Click on the RADAR Signal Processing Setting button in Radar signal information.
The RADAR Process dialog box appears.
2 Select the video process mode from the list in [Echo Process].
Radar signal processing setting button
Page 39
5-23 Section 5 Basic Operation of the Radar
1
2 3 4 5 5 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
APP A
APP B
Setting items
Effects and recommended use conditions
[Process Off]
Sets the image processing function to Off.
[3 Scan CORREL]
Use when the rain/snow clutter images are heavy.
[4 Scan CORREL]
Use when enhancing the target while suppressing sea clutter images.
[5 Scan CORREL]
Use when detecting small targets in sea clutter images.
[Remain]
Use when own ship is rolling severely.
[Peak Hold]
Use for detection of small targets of low detection probability.
5.4.5 Setting the azimuth mode
Set the bearing for the radar video to be displayed on the radar display.
1 Click on the Azimuth mode combo box in Presentation and mode information.
2 Select the Azimuth mode.
Note
Availab
le combinations vary depending on the settings of the azimuth mode and the
motion mode (refer to "5.4.6 Setting a motion mode".).
Azimuth mode
Motion mode
N UP H UP C UP W UP C UP
(Angle Setting)
TM  ×  ×
RM(T) or RM(R)
   
Azimuth Mode combo
box
Page 40
Section 5 Basic Operation of the Radar 5-24
The following azimuth modes can be set.
Setting items
Description
Display image
[N UP] North UP (North Up)
• The video is displayed so that the zenith of the PPI points to
the due north.
• Fixed targets do not flicker and are easily identified on the
chart, and the true bearing of a target can easily be read out.
[H UP] Head UP (Head Up)
• The video is displayed so that the ship’s heading line is
displayed at the top of the screen. Since targets are displayed
in their directions relative to the ship’s heading line, the
operator can view the video in the same field of view as in
operating the ship at sea. Therefore, This mode is suitable for
watching over other ships
• This is not available for TM (True Motion) mode.
[C UP] Course UP (Course Up)
• At the setting of Course Up, the ship’s heading (HDG) is fixed
and displayed immediately above the screen.
Similar to true
bearing display, the positions of stationary targets will
not deviate even if yawing occurs in the ship: targets
are displayed stably and the bearing of the heading line
moves only according to the amount of change in own
ship's course. To change the course, select the Course
UP display by clicking on the Azimuth mode combo box
several times. A course can be set again.
[W UP] Way Point UP (Waypoint Up)
• The destination is displayed at the top of the screen.
[C UP (Angle
Setting)]
Course UP by angle setting (Course Up by angle setting)
• When C UP is selected, the "C UP (Angle Setting)" dialog box
is displayed. The course angle that is set in the dialog box is
displayed by being fixed at the top of the screen.
- Input the angle of the ship’s heading in the [Angle] input
box of the "C UP (Angle Setting)" dialog box.
- The angle can also be input (increase/decrease) by
operating the angle input slider.
- After completing the setting, click on the [X] button.
North
North
Page 41
5-25 Section 5 Basic Operation of the Radar
1
2 3 4 5 5 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
APP A
APP B
5.4.6 Setting a motion mode
By setting a motion mode, the display method of the own ship’s position on the radar screen can be
changed.
Switching Relative Motion (RM) Mode to True Motion (TM) Mode
1
Click on the Motion Mode combo box in Presentation and mode information.
2 Select the motion mode.
Note
Availab
le combinations vary depending on the settings of the motion mode and the
azimuth mode (refer to "5.4.5 Setting the azimuth mode").
Azimuth mode
Motion mode
N UP H UP C UP W UP C UP
(Angle Setting)
TM  ×  ×
RM(T) or RM(R)
   
Motion Mode combo box
Page 42
Section 5 Basic Operation of the Radar 5-26
Setting items
Description
Display image
[TM]
True Motion Mode (True Motion display)
• In Ground mode, the own ship’s display
position moves according to the Speed
Over the Ground (SOG) and fixed targets
such as land are fixed on the radar screen.
• In Water mode, the own ship’s display
position moves according to the Speed
Through Water (STW) and fixed targets
such as land move according to the
difference between the Speed Through
Water (STW) and the Speed Over the
Ground (SOG).
• When the own ship reaches to the true
motion status, the own ship’s position is set
at the position of about 60% of the screen
radius in direction opposite to the own ship’s
course by adding the influence of the tidal
current. The ship’s position starts to move
according to the own ship’s speed, course,
and influence of the tidal current. When the
own ship’s position reaches the position of
about 60% of the screen radius, the position
is reset to the position of about 66% of the
screen radius in the direction opposite to the
own ship’s course (COG) by adding the
influence of the tidal current at that time.
[RM(T)] or [RM(R)]
Relative Motion Mode (Relative Motion display)
• Own ship is fixed at the center of the radar
screen and fixed targets such as land move
relatively.
[TM Reset]
TM Reset
• The own ship’s position is reset in [TM] (true
motion display) mode. For the details, refer
to "5.4.6.1 Resetting Own Ship to its Initial
Position in [TM] (True Motion display)
Mode".
5.4.6.1 Resetting Own Ship to its Initial Position in [TM] (True Motion display) Mode
1 Select [TM Reset] from the Motion Mode.
Own ship is reset to its initial position as established when the relative motion mode is changed
to the true motion mode. The ship starts moving from that position.
Fixed on the radar display
Moving
depending on own ship's speed
Page 43
5-27 Section 5 Basic Operation of the Radar
1
2 3 4 5 5 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
APP A
APP B
5.4.7 Setting the Stabilization Mode
1 Click on the Stabilization Mode button in Presentation and mode information
2 Select the Stabilization Mode.
[GND]: Use the ship speed relative to ground in the Stabilization Mode.
[Sea]: Use the ship speed relative to water in the Stabilization Mode.
5.4.8 Moving own ship’s display position (Off Center)
The own ship’s position can be moved from the display center to any position within 60% of the display
radius. This function is convenient for observing a wide coverage in any direction.
Note
This function is not available on the 96 NM range.
1 Click on the [Off Center] button in Presentation and mode information to turn the Off
Center mode to "On".
The Off Center mode is switched to On/Off whenever the button is clicked on.
Off Center mode is On:
Off Center mode is Off:
The cursor mode is set to the Off Center mode.
Stabilization Mode combo box
Page 44
Section 5 Basic Operation of the Radar 5-28
2 Place the cursor on the position you want to move and click on it.
Own ship’s display position will be moved to the clicked position.
Note
An own ship display position can be moved within the range in which the own ship display
position and the antenna position do not exceed 60% of the screen radius.
Returning own ship’s position to the center of the display
1
Click on the [Off Center] button in Presentation and mode information to disable the
Off Center mode.
The own ship position is returned to the center of the display (on relative motion) or the position
to be reset (on true motion).
5.4.9 Displaying other ship’s trails (Trails)
Other ships’ movements and speeds can be monitored from the lengths and directions of their trails,
serving for collision avoidance.
5.4.9.1 Trails motion mode
There are two types of trails: relative motion trail and true motion trail.
Relative motion trail: The system plots the trails of a target at a position relative to the own ship.
The operator can easily judge whether the target is approaching the own
ship.
While the own ship is moving, the system also plots the trails of land and
other fixed targets.
True motion trail: The system plots the absolute motion trails of a target, irrespective of the
own ship’s position.
The operator can easily judge the course and speed of the target.
The system does not plot the trails of land and other fixed targets.
HL
Clicking fixes
own ship's position.
HL
Position the cursor on
the destination.
Page 45
5-29 Section 5 Basic Operation of the Radar
1
2 3 4 5 5 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
APP A
APP B
While the true motion trail mode is active, this equipment enables the continuous use of true motion
trail even if any of the following operations is performed:
• Motion mode change (TM/RM)
• TM reset
• Azimuth mode change
• Off Center
• Chart display on/off (Chart)
Note
Accurate true bearing signals and
speed signals are necessary for using the true motion trail
mode.
Land
Land
Trail
Ship
Trail
Ship
True Motion Trail
Relative Motion Trail
Page 46
Section 5 Basic Operation of the Radar 5-30
5.4.9.2 Changing motion mode of trails
The trail display mode can be switched by using the Trail true/relative switching button of other ship
information.
Note
The available trail motion modes vary depending of the motion mode that is set.
True motion display (TM): Only true motion trail is available. Relative motion display (RM): Relative motion trail and true motion trail can be selected. [RM(R)] is displayed when relative motion trail is used.
[RM(T)] is displayed when true motion trail is used.
1 Click on the Trails True/Relative switch button.
Each time this button is clicked on, the display mode of Trails switches between [T] and [R].
[T]: (True motion trail)
[R]: (Relative motion trail)
Foe the details of the motion mode of trails, refer to "5.4.9.1 Trails motion mode".
5.4.9.3 Setting the length of the trail
1 Click on the Trail Length switch combo box in [Trails] of other ships' information.
Select a radar trail length.
Short mode: Off, 15 sec, 30 sec, 1 min, 3 min, 6 min, 10 min, 15 min, 30 min, 60 min
Long mode: Off, 30 min, 1 hr, 2 to 24 hrs (at 1 hr interval from 1 to 24 hrs)
Page 47
5-31 Section 5 Basic Operation of the Radar
1
2 3 4 5 5 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
APP A
APP B
Memo
Saved trails cannot be erased even when the trail lengths are changed the Trail Length switch
combo box.
Even after the trails display is turned off once, the past trails can be displayed traced back by
setting a desired time. The plot of the trail starts when starting the transmission.
The system is plotting trails even while the trails display is off.
If only a short
time has elapsed after the commencement of transmission, the display may not
reach the specified value. The time not to reach is indicated by the length of the blue bar shown at
the lower part of the Trail Length switch combo box.
5.4.9.4 Clearing trails data
1 Click on the [CLR] (clear trails) button.
The confirmation dialog box appears.
2 Click on the [OK] button.
All the saved trails data will be cleared. The system starts plotting trails in initial state.
CLR (clear trails) button.
Page 48
Section 5 Basic Operation of the Radar 5-32
5.4.10 Doubling the size of radar image
This function doubles the size of radar video near a specified position.
Note
If the range is 0.125 NM and the motion mode is in the TM mode, this function is not available.
1 Click on the radar signal process setting button in Radar signal information.
"RADAR Process" dialog box appears.
2 Click on the [X2(Zoom)] (double zoom) button.
Each time this button is clicked on, the double zoom function is switched On and Off.
On display:
Off display:
When double zoom is set, the cursor mode changes to the off-set cursor.
Radar signal process setting button
Page 49
5-33 Section 5 Basic Operation of the Radar
1
2 3 4 5 5 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
APP A
APP B
3 Place the offset cursor on a location you want to zoom and click on it.
Using the cursor position as the reference, the screen display is enlarged by a magnification of
2 so that the midpoint between the cursor and own ship's position comes at the center of the
radar display.
Canceling zoom display
1
Click on the [X2(Zoom)] button to turn the X2 Zoom function Off.
Off display:
Cursor mark
Own ship's
position
Cursor mark
Center of radar display
Own Ship's Position before
Zooming Position
Own Ship's Position after
Zooming Position
Page 50
Section 5 Basic Operation of the Radar 5-34
5.4.11 Hiding the heading line (HL OFF)
1 Click on the disclosure button on the left toolbar.
When the left toolbar is set to expanded display, this operation is not required.
2 The ship’s heading line is hidden while the
[
HL Off] button is pressed down.
When the button is released, the ship’s heading line is redisplayed.
Page 51
5-35 Section 5 Basic Operation of the Radar
1
2 3 4 5 5 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
APP A
APP B
5.4.12 Hiding graphics information on radar display
On the radar screen of this equipment, various types of graphics information such as TT/AIS symbol,
user map, and chart information are displayed. When the visibility of the radar screen deteriorates due
to excessive amount of graphic information displayed, the visibility of the screen can be improved by
temporarily clearing the unnecessary graphic information by using this function.
1 While the [Data OFF] button on the left toolbar is being held down, graphic information
other than the TT and AIS of danger targets, radar images, radar trails and cross
cursors are hidden.
When the button is released, graphics information is redisplayed.
5.4.13 Setting true bearing
When the GYRO I/F is used to enter a gyro signal, there is a rare case in which a true bearing value
indicated by the master gyro does not match the true bearing value indicated by this equipment.
In that case, adjust the true bearing value of this system so that it matches the value indicated by the
master gyro.
1 Click on the [Menu] button on the left toolbar.
A menu is displayed.
2 Click [Settings] - [General] on the menu.
The [General] dialog box appears.
Page 52
Section 5 Basic Operation of the Radar 5-36
3 Click on the input box of [GYRO Setting].
4 Input a master gyro value on the software keyboard.
5.4.14 Setting own ship speed
5.4.14.1 Switching own ship speed device
1 Select the ship speed device from the STW Source combo box in the own ship
information.
Page 53
5-37 Section 5 Basic Operation of the Radar
1
2 3 4 5 5 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
APP A
APP B
• When using 1-axis log, heading speed component can be detected, but
transverse speed component cannot be detected. Then leeway effect
(component drifted by wind) cannot be detected.
•
When using 2-axes ground log, its accuracy in shallow waters may be deteriorated, and its speed in deep sea areas may be unable to be detected.
•
When using a GPS, COG accuracy is less than ±3° at speed: from 1kn to
17kn, and is less than ±1° at speed: more than 17kn.
Page 54
Section 5 Basic Operation of the Radar 5-38
5.4.14.2 Entering the ship’s heading/own ship’s speed
manually
If any device such as LOG, etc., connected to this equipment malfunctions, it is possible to manually
enter own ship’s heading/speed by the method described below to use the target tracking (TT) and true
motion display functions.
1 Select [Menu] from the corresponding combo box.
The [Sensor Selection/Status] dialog box is displayed.
2 When inputting a ship’s heading manually, select [MAN] from the [Heading] combo
box. To input an own ship speed manually, select [MAN] from the [STW] combo box.
3 Click on the input box.
4 Enter a numeric value by using the software keyboard.
Page 55
6-1 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Section 6
Target Tracking and AIS
This section explains Target Tracking (hereinafter, referred to as target tracking or TT) and Automatic
Identification System (hereinafter referred to as AIS).
Use the target tracking function as your navigation aid. Final decision on the ship
operation must be made by the ship operator himself.
If you depend entirely on the information of the target tracking function for the final
decision on ship operation, an accident may occur.
An error may be contained in the vector, target value data and alarm indicated by the
target tracking function. Further, the target not detected by radar cannot be captured
or tracked.
If you depend entirely on the informa
tion of the radar for the final decision on ship
operation, such an accident as collision or stranding may result.
Simulation is a function for determining if the target tracking function is working
correctly or not. Accordingly, this function should b
e used only to check for the
target tracking function operation.
In particular, if this mode is used during navigation, a pseudo target will appear on the
radar screen and cannot be easily identified from the real target. This may cause
such an accident as collision. Do not use this mode during the navigation.
Target Tracking
This function calculates the course and speed of a target by automatically tracking the target's move.
This function enables the automatic acquisition of targets by using the automatic acquisition zone
function.
This function also enables the simulation of the ship maneuvering method to avoid collisions by using
the trial maneuver function.
Memo
If the mode is ground stabilization, SOG/COG used for own ship's information. If the mode is sea
stabilization, STW (speed through the water)/HDG (heading) is used for own ship's information.
Target tracking range is 32 NM. (Available all range scale)
For the details, refer to "6.5 Setting and Operating Target Tracking".
AIS
This function shows the target's information on the radar display, using other ship's information sent out
from the AIS unit.
For the details, refer to "6.6 Setting and Operating AIS".
Page 56
Section 6 Target Tracking and AIS 6-2
6.1 Restrictions
The acquisition and Target Tracking functions have the following restrictions.
Depending on distance and echo size, resolution between adjacent targets during automatic target
tracking usually ranges somewhere between 0.03 to 0.05 NM. If multiple targets approach each other,
there is a possibility of swapping them or losing one of them. Such swapping or less of targets may
also occur if the target being tracked is affected by rain/snow clutter or sea clutter or moves very close
to land.
The intensity of echoes and the Target Tracking function have a correlationship, and thus the target will
be lost if no echoes are detected during six scans in succession.
If such a lost target exists, therefore, radar gain must be increased to support detection of the target. If,
however, radar gain is increased too significantly, sea clutter or other noise may be erroneously
detected and tracked as a target, and resultingly, a false alarm may be issued.
To execute accurate tracking, it becomes necessary first to appropriately adjust the gain, sea clutter
suppression, rain/snow clutter suppression and tune of the radar so that the target to be acquired and
tracked is clearly displayed on the radar display.
Inappropriate settings of these adjustments reduce the reliability/accuracy of automatic target tracking.
Page 57
6-3 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
6.2 Collision Avoidance Issue
(Explanation)
6.2.1 Collision Avoidance in Navigation
Marine collision avoidance in navigation is one of the problems that have been recognized from of old.
This section contains a brief statement about the position of collision avoidance in navigation.
The navigation pattern of all mobile craft constitutes a system with some closed loops regardless of the
media through which the mobile craft travels, whether air, water, the boundary between air and water,
or space. This pattern consists of two closed loops in principle, one of which is a collision avoidance
with another mobile craft and the other is a loop of finding a right and safe way to reach a
predeterminate destination.
The following figure shows the conceptual diagram of navigation pattern by Mr. E.W. Anderson. The
closed loop of collision avoidance is shown on the left side and the closed loop of finding a safe route
on the right side.
6.2.2 Marine Accidents and Collisions
Among marine accidents, collision accidents have been highlighted as the tonnages and speeds of
ships become higher along with the increase in traffic at sea.
If a tanker carrying dangerous articles such as crude oil collides with any other vessel, then not only
the vessels involved with the accident but other vessels in the vicinity, port facilities and inhabitants in
the coastal area as well as marine resources may also suffer immeasurable influence.
Collision accidents have a high percentage of the marine accidents that have occurred in recent years.
To cope with these problems, any effective measures are needed and some equipment to achieve
collision avoidance requirements has been developed at rapid strides.
Destination
Maneuver
Cource and
speed
Route
Ship traveling in controlled condition
Instrument or
judgement
Control
loop
Compass
and log
Calculation
Decided by radio wave,
visual and observation
Judgement
Visual and radio wave monitoring
Traffic rule
Collision
avoidance loop
Vessel’s spacing loop
Collision avoidance Decision of route
Guide loop
Dead
reckoning
Navigation Pattern
Page 58
Section 6 Target Tracking and AIS 6-4
6.2.3 Basic Concept of Collision Avoidance
There are two aspects in collision avoidance: collision prediction and avoidance. Putting it in extreme
terms, collision prediction is to predict that two or more vessels will happen to occupy the same point at
the same time, while collision avoidance is to maneuver vessels not to occupy the same point at the
same time.
In practical operation of vessels, a spot of collision has to be deemed to be a single point but a closed
zone. This closed zone is conceptually defined as a CPA (Closest Point of Approach). Further, the
time taken to arrive at CPA is required for collision prediction, and the danger of collision is judged
considering the TCPA (Time to CPA). The following figure illustrates a diagram caked "Collision
Triangle".
Own ship
CPA ring
True vector of own ship
True vector of
target vessel
Target vessel
TCPA
(Time to CPA)
Relative vector
Collision
triangle
Page 59
6-5 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
6.2.4 Relative Vector and True Vector
From two points of view, collision prediction and avoidance, it is necessary to obtain the relative vector
of other ship for prediction and the true vector of other ship for collision avoidance in order to realize
other ship's aspect.
The relationship between the relative vector and true vector is shown in the following figure.
Furthermore, the meanings of both vectors are explained.
Both rough CPA and TCPA can be obtained easily from the relative speed vector of other ship. This
method has an advantage that the risks of collision with all other ships within the radar range can be
seen at a glance. On the other hand, the course and speed of other ship can easily be obtained from its
true speed vector, enabling other ship's aspect to be seen at a glance. Thus, the aspects of other ships
(transverse, outsail, parallel run, reverse run, etc.) as described in the act of prevention of collision at
sea can be readily understood. If there is a risk of collision with other ship, the operator can determine
which rule to be applied and how to operate own ship.
6.2.5 Radar and Collision Avoidance
Radar is still playing an important role for collision prevention and positioning.
A plotter is used to further enhance the radar functionality. The plotter is capable of plotting other
positions of other ships in 3 to 6 minute intervals to monitor their movement. The plots of other ships
represent their tracks relative to own ship, and it is shown whether there is a risk of collision, namely
CPA and TCPA can be obtained. This method using a plotter is fairly effective, but the number of target
ship, which is manually plotted, is limited and it takes several minutes to measure those.
θ
T
θ
R
θ
A
θ
O
V
o
V
R
V
T
Vα: Own ship’s speed
θα: Own ship’s course
V
T
: Target ship’s true speed
θ
T
: Target ship’s true course
V
R
: Target ship’s relative speed
θ
R
: Target ship’s relative course
θ
A
: Aspect
N
N
CPA
Relative vector
Own ship true vector
Target ship true vector
Page 60
Section 6 Target Tracking and AIS 6-6
6.3 Displaying Symbols
This section describes the symbols that are used for target tracking and AIS.
6.3.1 Displaying/hiding target tracking symbols/AIS
target symbols
In the display setting at the time of shipment from the factory, the display of target tracking symbols and
of the AIS target symbols is enabled. However, choosing [Options] – [Target] from the View menu can
switch between display and hide.
For the details, refer to "16.2.7 Setting up the display of TT/AIS target".
6.3.2 Types and Definitions of Target Tracking
Symbols
Symbol Definition Remarks
Initial acquisition target
This symbol is displayed until the vector is displayed after target acquisition.
Target acquired in automatic acquisition zone
The alarm sounds. The alarm message (New Target) turns orange and blinks. The symbol turns red and blinks.
Tracked target This means a tracked target.
Dangerous target
The alarm sounds. The alarm message (CPA/TCPA) turns red and blinks. The symbol is enlarged and displayed in red.
Numeric displayed target
When the numeric data is displayed, the target symbol is enclosed in a square.
Lost target
The alarm sounds. The alarm message (Lost) turns orange and blinks. The symbol turns red.
Past position
The past positions of an AIS target are displayed as well as the target tracking symbol.
Target track
The track of another ship as an AIS target is displayed as well as the target tracking symbol.
12 12
12
12
251659264
12
12 12 12
Page 61
6-7 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
6.3.3 Types and Definitions of AIS Target Symbols
Symbol Definition Remarks
Sleeping target
This symbol is displayed when received data is valid. The direction of the triangle's vertex indicates the target's heading or course.
Activated target
The heading direction is displayed with a solid line, and the course vector is displayed with a dotted line. The line perpendicular to the heading direction indicates the direction to which the course is to be changed. This line may not be displayed.
Outline display The outlines of ships are displayed scaled down.
Numeric displayed target
When the numeric data is displayed, the target symbol is enclosed in a square.
Dangerous target
The alarm sounds. The alarm message (CPA/TCPA) turns red and blinks. The symbol is enlarged and displayed in red.
Lost target
The alarm sounds. The alarm message (Lost) turns orange and blinks. The symbol is displayed by overlaying red x marks.
Sleeping AIS-SART target
Displayed by the same color as AIS symbol.
Activated AIS-SART target
Displayed target No. nearby the symbol.
Numerical display AIS-SART target
When the numeric data is displayed, the target symbol is enclosed in a square.
Lost AIS-SART target
Displayed if AIS-SART data is not received for 6 minutes.
AIS12
AIS12
AIS12
AIS12
25166028
AIS12
AIS12
AIS12
AIS12
Page 62
Section 6 Target Tracking and AIS 6-8
Symbol Definition Remarks
X X X
Real AIS AtoN target
(On position)
Displayed target No./AtoN name (xxx) nearby the symbol.
X X X
Real AIS AtoN target
(Off position)
The symbol and target No./AtoN name (xxx) nearby the symbol are indicated in red.
X X X
Real AIS AtoN target
(Numerical display)
When the numeric data is displayed, the target symbol is enclosed in a square.
X X X
Real AIS AtoN target
(Lost)
The alarm sounds. The alarm message (Lost) turns orange and blinks. The symbol is displayed by overlaying red x marks.
X X X
Virtual AIS AtoN target
(On position)
Displayed target No./AtoN name (xxx) nearby the symbol.
X X X
Virtual AIS AtoN target
(Off position)
The symbol and target No./AtoN name (xxx) nearby the symbol are indicated in red.
X X X
Virtual AIS AtoN target
(Numerical display)
When the numeric data is displayed, the target symbol is enclosed in a square.
X X X
Virtual AIS AtoN target
(Lost)
The alarm sounds. The alarm message (Lost) turns orange and blinks. The symbol is displayed by overlaying red x marks.
AIS SAR aircraft
Displayed by the same color as AIS symbol.
Numerical display
AIS SAR aircraft
When the numeric data is displayed, the target symbol is enclosed in a square.
Lost AIS SAR
aircraft
The alarm sounds. The alarm message (Lost) turns orange and blinks. The symbol is displayed by overlaying red x marks.
Page 63
6-9 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Symbol Definition Remarks
AIS coastal base
station
Displayed by the same color as AIS symbol.
Numerical display
AIS coastal base
station
When the numeric data is displayed, the target symbol is enclosed in a square.
Lost AIS coastal
base station
The alarm sounds. The alarm message (Lost) turns orange and blinks. The symbol is displayed by overlaying red x marks.
Page 64
Section 6 Target Tracking and AIS 6-10
6.3.4 About AIS AtoN (Aids to Navigation)
AIS AtoN is a system that displaying aid to navigation like a lighthouse, light buoy or unreal aid to
navigation on the display unit on ships using AIS receiver.
There are following two kinds of AIS AtoN.
AIS AtoN type
Function
Operation example
Real AIS AtoN Installs the AIS on real aid to
navigation, and displays its location
on the display unit on ships.
In low visibility, receiving the Real AIS
AtoN symbols facilitates identification of
the light location and light buoy.
Virtual AIS AtoN Displays virtual aid to navigation on
the display unit on ships according
to the signals transmitted from the
AIS station on the land.
In the sea area where installation of the
light buoy is difficult, the Virtual AIS AtoN
symbols are displayed as virtual light
buoys that are used as targets for getting
to the destination.
This system can also be used as the aid
substituted for the aid to navigation
damaged by natural disasters.
6.3.5 About AIS-SART Information
The AIS-SART function enables information about the location of wrecked ship to be displayed on the
screen.
For the details, refer to "7.5 Display of AIS-SART".
6.3.6 About Display Priority of AIS Targets
Up to 500*1 targets can be displayed in total of activated and sleeping AIS targets. Up to 500 activated
AIS targets can be displayed in the total.
When there is an AIS target of 500
*1
or more, the display is made according to the following priority
order.
*1: The maximum number of AIS targets displayed can be changed to the option of 1000 targets.
If the number of targets at the same priority level exceeds the allowable maximum, they are displayed
in the following priority order:
1. Association target
2. Activated AIS target
3. Sleeping AIS target
High priority
Low priority
1. Numeric displayed target
2. Target of which CPA/TCPA is lower than the set value
(Target as a dangerous ship for which an alarm has been generated)
3. Target in automatic activation zone
4. Activated AIS target
5. Target inside AIS filter
6. Target outside AIS filter
High priority
Low priority
Page 65
6-11 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
6.3.7 Switching between Ground Vector and Water
Vector
The vector of an AIS target is to be displayed with a vector over ground or over water by switching the
stabilization mode. The type of the currently displayed vector can be confirmed by viewing the setting
of the stable mode.
When [GND] is selected for the stabilization mode: Ground vector
When [Sea] is displayed for the stabilization mode: Water vector
When the vector of an AIS target is displayed with a vector over water, the system has converted the
AIS target's vector over ground to the vector over water according to the data received from the AIS
and the own ship's information.
6.3.8 Association Target Symbols
When the TT target and AIS target are determined to be the same targets, the association symbols are
displayed as follows.
Symbol display for high-priority TT targets Symbol display for high-priority AIS targets
When the TT target and AIS target are determined to be the same targets, the TT target or AIS target
that are displayed on a higher priority basis can be set.
1 Right-click on the tracked target with association displayed.
The context menu appears.
2 Click on [Property] in the context menu.
The "TT Target INFO" or "AIS Target INFO" dialog appears.
3 Select [AIS] or [TT] from the [Priority] combo box.
[AIS]: The AIS target is displayed on a higher priority basis.
[TT]: The TT target is displayed on a higher priority basis.
Association targets
Association targets
Page 66
Section 6 Target Tracking and AIS 6-12
6.4 Preparation
6.4.1 Setting the Cursor Mode to AUTO Mode
If the cursor mode is set to the AUTO mode, various TT/AIS functions can be executed quickly.
1 Click on the [AUTO] (cursor mode selection) button on the left toolbar.
The cursor mode changes to the AUTO mode.
The [AUTO] mode performs operation in accordance with the object at the cursor position when
clicked.
For the details, refer to "3.12 Cursor AUTO Mode".
6.4.2 Setting Vector
A vector to represent a target's predicted position can be presented in the True vector or Relative
vector mode. In each mode, a Vector Length can be freely changed for a time interval of 1 to 120
minutes.
6.4.2.1 Vector modes
Different vector modes can be used as described below according to the purpose.
To perceive the true state of the target: True Vector
To perceive the closest approach point of the target: Relative Vector
Page 67
6-13 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
True vector mode
In the true vector mode, the directions of vectors indicate the true courses of targets and the Vector
Lengths indicate the values which are proportional to their speeds.
In the true vector mode, the movements of other ships around own ship can be accurately and easily
monitored.
Vectors of own ship are displayed as shown below.
Note
In true vector mode, CPA ring cannot be displayed.
Relative Vector Mode
The relative vector does not represent the true motion of the target, but its relative relation with own
ship. A target with its relative vector directed to own ship (passing through the CPA limit ring) will be a
dangerous target.
In the Relative Vector mode, it can be seen at a glance where the CPA limit of the dangerous target is.
The true vector is not displayed.
CPA ring
Relative vector
Example of Relative Vector Mode
The relative vector is not displayed.
Own ship's vector
Example of True Vector Mode
HL
True vector
Page 68
Section 6 Target Tracking and AIS 6-14
6.4.2.2 Setting vector mode
1
Click on the trail true/relative selector button in the other ship information window.
Each click switches track display mode between [T] and [R].
6.4.2.3 Vector Length (Vector Time)
The Vector Length of a target is proportional to its speed, and the vector time can be switched in a
range of 1 to 120 minutes.
The following figure shows an example in which the Vector Length is set to 6 min, and the tip of the
vector represents the target's position expected to reach 6 minutes later.
HL
Current position
Future predicted position (6 min later in this example)
Example of Vector Length
Trail true/relative selector button
Page 69
6-15 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
6.4.2.4 Setting the Vector Length
The Vector Length is set in min in the range from 1 min to 120 min.
1 Click on the Vector Length input box in the other ship information window.
2 Enter the Vector Length.
6.4.3 Setting collision decision criteria
Collision decision criteria are set based on CPA and TCPA.
For an outline of CPA and TCPA, refer to "6.2.3 Basic Concept of Collision Avoidance."
Note
Set the optimum values of collision decision conditions, with consideration for vessel type, water
area, weather and oceanographic conditions.
For the relations between those conditions and alarms, refer to "6.7 Alert Display".
6.4.3.1 Setting CPA limit
1
Click on the CPA limit value input box in the other ship information window.
Set the CPA limit in the unit of 0.1 NM within the range from 0.1 NM to 9.9 NM.
2 Enter the CPA limit.
CPA limit value input box
Vector Length input box
Page 70
Section 6 Target Tracking and AIS 6-16
6.4.3.2 Setting TCPA limit
1
Click on the TCPA limit value input box in the other ship information window.
Set the TCPA limit in the unit of 1 min within the range from 1 min to 99 min.
2 Enter the TCPA limit.
For the details on how to set up alerts based on the collision determination condition, refer to
"17.2 Collision Avoidance Alert Generation Conditions".
TCPA limit value input box
Page 71
6-17 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
6.4.4 Showing the CPA ring (RADAR only)
The CPA ring is rendered as a red circle with the own ship centered and the CPA limit set distance used
as the radius.
1 Click on the [Menu] button on the left toolbar.
The menu is displayed.
2 Click on [View] - [Option] - [Target].
The [Target] dialog is displayed.
3 Select [CPA Ring (Only Relative mode)].
The CPA ring is shown.
Note:
When True is specified for the vector mode, [CPA Ring (Only Relative mode)] cannot be selected.
[CPA Ring (Only Relative mode)]
Page 72
Section 6 Target Tracking and AIS 6-18
6.5 Setting and Operating Target Tracking
The Target Tracking function automatically tracks the acquired targets and records and displays the
course and speed of the targets as vector. Alerts can also be output based on the set collision decision
criteria (CPA and TCPA).
Note
At power off and during preparation for transmission, tracking data records are deleted.
6.5.1 Acquiring target
The methods for acquiring targets include Auto Acquisition (automatic acquisition) mode and ACQ
MANUAL (manual acquisition) mode.
Both modes can also be used concurrently.
6.5.1.1 Automatic acquisition (automatic acquisition) mode
By setting up and enabling the automatic acquisition/activation zone (AZ), targets intruding into the AZ
can automatically be acquired/tracked and also issue a new target warning.
Note
If manual acquisition is made in a state in which the number of targets being tracked has reached
the maximum number of targets, the target with the lowest danger level among the targets that
have been captured thus far automatically is erased successively.
Take the following steps to enable automatic acquisition/activation zone (AZ).
1 Click on the [Menu] button on the left toolbar.
The menu is displayed.
2 Click [Alert] - [New Target Alarm] on the menu.
The "New Target Alarm" dialog is displayed.
Page 73
6-19 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
3 Check [Use AZ1] (automatic acquisition zone 1) or [Use AZ2] (automatic acquisition
zone 2).
Automatic acquisition/activation zone (AZ) includes AZ1 and AZ2.
To enable AZ1, check [Use AZ1].
To enable AZ2, check [Use AZ2].
Memo
For the details of "New Target Alarm" dialog box, refer to "17.3 New Target Alarm Generation
Conditions".
To automatic acquisition/activation zone (AZ):
Clear the check of [Use AZ1] or [Use AZ2].
The AZ can also be enabled/disabled with the [AZ] key on the keyboard operation unit.
For the details of function assignment to the [AZ] key, refer to "18.20 Setting Key Assignment".
6.5.1.2 ACQ MANUAL (manual acquisition) mode
Note
The manual acquisition mode does not function in the following states.
State
Action to Take
The number of tracked targets has reached the maximum count.
Erase unnecessary targets.
The radar antenna is in the standby state. Wait until the radar antenna becomes ready.
A PROC (Interrupt) warning is being generated. Clear the warning.
A Gyro (I/F)/Gyro (Data)/Heading (Data) warning is being generated.
The tracked target is located 32 NM away from own ship. The manual acquisition mode cannot be
used.
The tracked target is located less than 0.1 NM from own ship.
To acquire the tracked target in the manual acquisition mode
1 Set the cursor mode to the AUTO mode.
2 Place the cursor on the target to be acquired and then click on.
The target is acquired and the initial acquisition symbol is displayed.
The vector is displayed within 1 minute.
Page 74
Section 6 Target Tracking and AIS 6-20
Memo
If only the manual acquisition mode will be used without using auto acquisition/activation together,
disable the AZ.
6.5.1.3 Using manual acquisition and auto acquisition together
By using manual acquisition with AZ enabled, auto acquisition and manual acquisition can be used
together. They may be used if a target to which particular attention should be given is manually
acquired and other targets are automatically acquired.
Note
If a new target intrudes exceeding the maximum number of targets, the targets manually acquired
are displayed even in the rearward until they go out of the screen. However, the targets
automatically acquired are erased from those in the rearward.
6.5.2 Setting up the automatic
acquisition/activation zone (AZ)
Auto acquisition/activation zone has the shape of sector set up according to the angle and distance as
shown in the following figure.
Start angle
AZ1
AZ2
Start distance
End distance
End angle
Example of auto acquisition/activation zone (AZ)
Target manually acquired. The initial acquisition symbol is displayed.
Target that has passed for 1 min. The acquisition symbol and vector are displayed.
Page 75
6-21 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Auto acquisition/activation zone (AZ) is set up using the following three methods.
(1) Use the "New Target Warning" dialog in the [Alert] menu.
(2) Use the cursor.
(3) Use the EBL/VRM dial.
6.5.2.1 Using "New Target Warning" dialog box in the [Alert] menu
1
Click on the [Menu] button on the left toolbar.
The menu is displayed.
2 Click [Alert] - [New Target Alarm] on the menu.
The "New Target Alarm" dialog is displayed.
3 To set up AZ1, select the [Use AZ1] check box. To set up AZ2, select the [Use AZ2]
check box.
4 To set up [Use AZ1], click on the [1] tab. To set up [Use AZ2], click on the [2] tab.
Their respective setting items are displayed.
5 Enter the start angle, end angle, start distance and end distance of AZ.
Start angle
End angle
Start distance
End distance
Page 76
Section 6 Target Tracking and AIS 6-22
6.5.2.2 Using the cursor
1
Click on the [Menu] button on the left toolbar.
The menu is displayed.
2 Click [Alert] - [New Target Alarm] on the menu.
The "New Target Alarm" dialog is displayed.
3 Select AZ ([Use AZ1] or [Use AZ2]) to be set.
4 Click at the start angle position.
The start angle is set.
5 Move the cursor and click at the end angle position.
The line connecting the start angle and end angle appears.
6 Move the cursor and click at the start distance position.
An arc appears at the start distance position.
7 Move the cursor and click at the end distance position.
Auto acquisition/activation zone (AZ) with the shape of sector enclosed by start angle, end
angle, start distance and end distance is created.
Page 77
6-23 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
6.5.2.3 Using the EBL/VRM dial for the setting
1
Click on the [Menu] button on the left toolbar.
The menu is displayed.
2 Click [Alert] - [New Target Alarm] on the menu.
The "New Target Alarm" dialog is displayed.
3 Select AZ ([Use AZ1] or [Use AZ2]) to be set.
4 Click on the [Make AZ1] button or [Make AZ2] button.
The cursor enters the AZ creation mode.
5 Turn the EBL dial to set [Start Angle].
6 Turn the VRM dial to set [Start Distance]
7 Press the EBL dial and the VRM dial.
8 Turn the EBL dial to set [End Angle].
Start angle
Start distance
Page 78
Section 6 Target Tracking and AIS 6-24
9 Turn the VRM dial to set [End Distance].
10 Press the EBL dial.
6.5.3 Tracked target information display
Note
When a target or own ship changes its course, or when a new target is acquired, its vector may not
reach a given level of accuracy until 3 minutes or more has passed after such course change or
target acquisition.
Even if 3 minutes or more has passed, the
vector may include an error depending upon the
tracking conditions.
1 Set the cursor mode to the AUTO mode.
2 Click on the target of tracking whose numerical value is to be displayed.
Numeric data for the specified target is displayed in the information monitoring window.
Eng angle
End distance
Page 79
6-25 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
The symbol display is changed to " ". The target data will remain on the radar display until
the target is lost and its vector disappears, or until another target is designated.
If a target with the mark " " is designated, only its true bearing and range appear until its
vector appears.
Cancellation of numeric data display
1 Set the cursor mode to the AUTO mode.
2 Place the cursor on the tracked target to cancel numeric value display and then click
on.
The numeric value disappears.
Details on tracked target information
Item Explanation
TT ID ID No. of tracked target being displayed
BRG True bearing
Range Distance
CTW (Course Through the
Water stabilization mode)/
COG (Course Over the
Ground stabilization mode)
Course
STW (Speed Through the
Water stabilization mode) /
SOG (Speed Over the
Ground stabilization mode)
Speed
CPA Closest approach distance
TCPA Time up to closest approach distance
BCR Bow crossing distance
BCT Bow crossing time
6.5.4 Erasing unwanted tracked targets
If the vectors and symbols of the unwanted tracked targets remain displayed, the radar screen may
become difficult to view. In such a case, unwanted tracked targets can be erased from the radar screen
using the following method.
To erase one target
1 Place the cursor on the tracked target to be cancelled and then right-click.
The context menu is displayed.
2 Click on the [Cancel TT] on the context menu.
The vector symbol of the tracked target disappears and only the radar image remains.
Page 80
Section 6 Target Tracking and AIS 6-26
To erase multiple targets
1 Place the cursor on the tracked target to be cancelled and then right-click.
The context menu is displayed.
2 Click on the [Cancel TT mode] on the Context menu.
The cursor changes to the selection cursor.
3 Place the cursor on another target to be cancelled and then click on.
4 Repeat the operation in step 3.
The vector symbols of the clicked tracked targets disappear and only the radar image remains.
To erase all targets
1 Place the cursor on the tracked target to be cancelled and then right-click.
The context menu is displayed.
2 Click on the [Cancel all TT mode] on the Context menu.
The vector symbols of all the tracked targets disappear and only the radar image remains.
Note
If all targets are cancel
led, the tracking of all targets will stop; thus, automatic acquisition or
manual acquisition must be performed newly. Unless necessary, do not cancel all targets.
6.5.5 Displaying Target ID No.
A target ID number is a value displayed beside the acquisition symbol when a target is acquired.
A target ID number 1 to 100 is automatically assigned to each target in acquisition order. Once a target
ID number is assigned, it identifies the target until the target is lost or the target acquisition is canceled.
Memo
The ID number is always displayed for only targets with which numeric data is displayed.
1 Click on the [Menu] button on the left toolbar.
The menu is displayed.
2 Click on [View] - [Options] - [Target].
The "Target" dialog is displayed.
Page 81
6-27 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
3 Select the method for displaying ID No. from the [TT Target ID] list.
[On]: Displays target ID numbers.
[Off]: Hides target ID numbers.
[TT Track]: Displays ID numbers of only targets set for track of other ships.
[Ship's Name]: When the ship’s name has been input in the “TT Target INFO” (property of
tracked target) dialog box, that ship name is displayed. If the ship’s name has
not been input, the identification number is displayed.
Memo
If there are many tracking targets and their symbol display is confusing, set Target Number Display
to off to view the radar display easily.
[TT Target ID]
[TT Target ID]
ECDIS screen
RADAR screen
Page 82
Section 6 Target Tracking and AIS 6-28
6.5.6 Editing tracked target properties
The tracked target property such as tracked target ID name can be arbitrarily edited for individual
tracked targets acquired.
The "TT Target INFO" dialog is used for editing.
6.5.6.1 Adding Tracked Target ID Name
An ID name can be added to the tracked target acquired.
1 Right-click the cursor on the tracked target.
The context menu is displayed.
2 Click on [Property] on the context menu.
The "TT Target INFO" dialog box appears
[Target ID] display
[Name] input box
[Edit Template] button
Tracked target ID appears.
Tracked target ID name is set.
For the details, refer to "6.5.6.1 Adding Tracked Target ID Name".
The track color of tracked target is set. For the details, refer to "6.5.6.2 Setting track color of tracked target".
The target for which ground is fixed is set to a reference target.
For the details, refer to "6.5.7 Setting target for which ground is fixed to a reference target"
When a TT target and AIS target are determined to be the same targets, the TT target or AIS target to be displayed on a priority basis can be set. For the details, refer to "6.3.8 Association Target Symbols"
Page 83
6-29 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
3
Click on the [Name] input box or .
The input method varies with the selected item.
Input box : Enter a new name.
When selected, the ship name ([Name]) entry window opens.
Enter a ship name of up to 15 characters.
: The names registered as templates are displayed in a list.
Select a name from the list.
To register ship names as templates
1 Click on the [Edit Template] button in the [TT Target INFO] dialog box.
The [Edit Template] dialog box appears.
2 Enter the ship name to be registered as a template in the input text box.
3 Click on the [Register] button.
The entered ship name is registered in the template list.
4 Repeat steps 2 and 3, and register necessary ship names.
To cancel unwanted ship name registration
1 On the template list in the [Edit Template] dialog box, check the checkbox of the ship
name whose registration to be canceled.
2 Click on the [Delete] button.
The checked ship name is deleted from the template list.
Input text box
[Register] button
Template list
[Delete] button
Page 84
Section 6 Target Tracking and AIS 6-30
6.5.6.2 Setting track color of tracked target
The track color of tracked target is set.
1 Right-click on the cursor at the tracked target.
2 Click on the [Property] on the context menu.
The "TT Target INFO" dialog box appears.
3 Select track color from the [Track Color] list.
The selection items are as follows.
Off, No.1-Color, No.2-Color, No.3-Color, No.4-Color, No.5-Color, No.6-Color, No.7-Color,
No.8-Color, No.9-Color, No.10-Co lor, No.11 to 20-Color
* In "Color," the track color name set by clicking [View] - [Options] - [Target Track] - [Plot]
appears. For the details, refer to "16.2.8 Setting up the Display of Other Ship's Track"
Page 85
6-31 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
6.5.7 Setting target for which ground is fixed to a
reference target
By tracking the target for which ground is fixed and setting it to a reference target, the speed of the own
ship can be obtained and displayed.
Note
• T
he reference target function is to be used if the own ship's speed cannot be displayed
normally due to trouble such as a speed sensor malfunction. Do not use the reference target
function except in emergencies.
• If the speed or course of the own ship is cha
nged or a new reference target is set, the
displayed speed may take 3 minutes or more to reach the specified speed after the
speed/course change or the setting.
Even after 3 minutes or more has passed, the speed may differ from the specified speed
depending on the tracking condition.
•
If a large radar echo such as a land target is set as a reference target, the vectors of the
speed and other tracking targets will not be displayed correctly and may cause an accident.
• If a sailing ship is set as a reference target, the vectors of the speed and other tracking targets
will not be displayed correctly and may cause an accident.
• If the reference target is lost or the Target Tracking function is stopped, the ship speed against
the ground will be GPS. (Only if the GPS is equipped.).
• If the reference target is lost or the Target Tracking function is stopped, that will make a major
impact on the accuracy of the target tracking and the own ship speed.
• The reference targets are only used for the calculation of true speed.
•
Do not use own speed based on reference target tracking for relative speed and CPA/TCPA
calculation of AIS targets because the response of own speed is slower than actual own
ship's speed change and it may cause a big error on the collision judgement of AIS targets.
1 Acquire the ground-fixed target.
2 Click the right button on the acquired target.
A context menu is displayed.
Page 86
Section 6 Target Tracking and AIS 6-32
3 Click on [Property] in the context menu.
The “TT Target INFO” dialog is opened.
4 To set the target to a reference target, check [Reference Target].
To not set the target to a reference target, uncheck [Reference Target].
5 Select [TGT] from the COG/SOG source combo box in the own ship information at the
top right corner of the screen.
The ship speed is automatically calculated from the reference target and is displayed as the
COG/SOG speed.
When a reference target is set, the symbol display changes to “
R
”.
Note
Only one target can be set as a reference target.
When a new reference target is set, the previous reference target is cancelled.
[Reference Target]
check box
Page 87
6-33 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
6.5.8 Operation Test for Target Tracking
Simulation is a function for determining if the target tracking function is working
correctly or not. Accordingly, this function should be used only to check for the target
tracking function operation.
In particular, if this mode is used during navigation, a pseudo target will appear
on the radar screen and cannot be easily identified from the real target. This
may cause such an accident as collision. Do not use this mode during the
navigation.
The following operation test and checking are performed to check the operation of target tracking as
required. The "TT Te s t" dialog is used for operation.
1 Click on the [Menu] button on the left toolbar.
The menu is displayed.
2 Click on the [Settings] - [TT Test] on the menu.
The "TT Te s t" (Test for Target Tracking) dialog is displayed.
A pseudo-target is generated on the radar screen to check that
target tracking operates normally. For the details, refer to "6.5.8.2 Target tracking simulator (TT Simulator)".
The gate size for acquiring and tracking targets are displayed. For the details, refer to "6.5.8.3 Gate display".
The status of Target Tracking function is displayed.
For the details, refer to "6.5.8.4 Status display".
The operation of target detection circuit is checked.
For the details, refer to "6.5.8.1 Test Video".
Page 88
Section 6 Target Tracking and AIS 6-34
6.5.8.1 Test Video
Test Video is used to check whether the video signals under target acquisition and tracking are input to
and processed in the target detection circuit normally.
Normally, it is sufficient to just check that the VDIN of the Test Video is displayed.
Note
Test Video may not be displayed for a target which is not yet acquired or tracked. Test Video may
not be displayed either if the [GAIN] dial or [SEA] dial is not properly adjusted.
1 Click on the [Menu] button on the left toolbar.
The menu is displayed.
2 Click on the [Settings] - [TT Test] on the menu.
The "TT Test" (Test for Target Tracking) dialog is displayed.
3 Select test video to be displayed from the [Test Video] combo box.
The selected test video is displayed in the rearward of the radar image.
If any target displayed clearly in the normal radar display is not displayed in the Test Video mode, the
target detection circuit of the Target Tracking unit may have a trouble.
To cancel test video
1 Select [Off] from the [Test Video] combo box.
Test Video display turns off.
Page 89
6-35 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
6.5.8.2 [TT Simulator] (Target tracking simulator)
Pseudo-targets are generated in certain known positions to check whether the target tracking units are
operating normally. Since the pseudo-targets move depending on known parameters, the values for
these pseudo-targets can be compared with the known value if the pseudo-targets are acquired and
tracked, and displayed. Thus, it can be checked if the system is operating normally.
1 Click on the Standby/Transmit selector button for Radar system information to place
the radar in the standby state.
The button indication changes to [Standby].
2 Click on the [Menu] button on the left toolbar.
The menu is displayed.
3 Click on the [Settings] - [TT Test] on the menu.
The "TT Test" (Test for Target Tracking) dialog is displayed.
4 Select simulator scenario from the [TT Simulator] combo box.
Standby/Transmit selector button
Page 90
Section 6 Target Tracking and AIS 6-36
List of target tracking simulator/scenario
Scenario Target No.
Motion
(true motion)
Moving start point
Speed [kn]
Course [o]
Range [NM]
Bearing [o]
Scenario1
1
28.3
45
9.5
270
2
22.4
27
1.12
333
3
15.3
293
9.25
45
Scenario2
1
30
135 8 23 2 20
270 5 135
Scenario3
1
45
180 5 23 2 0 - 3
340 3 30 0 8
180
Scenario4
1 0 0
2.02
31 2 70
225
7.01
37
Scenario5
1
20
45
4.47
288 2 30
45
5.1
304 3 40
45
6.71
288 4 0
-
7.07
307 5 60
200
12
352 6 20
225
11
315 7 40
190
14.4
349 8 - - 8
318 9 - - 9
318
10 - -
10
318
Scenario6
1
5
96 5 0 2 105
225 6 45
Note
• When the simulator is operating, set 0° as the heading bearing
5 Click on the Standby/Transmit selector button to place the radar in the transmission
state.
The button indication changes to [Transmit].
The simulator turns on, the pseudo-target is generated, and the letter "X" appears on the lower
side of the radar screen and near the pseudo-target to indicate that simulation mode is being
executed.
To cancel simulation
1 Click on the Standby/Transmit selector button to place the radar in the standby state.
The button indication changes to [Standby] to enter transmission preparation state.
2 Select [Off] from the [TT Simulator] combo box in the "TT Test" dialog.
TT Simulator display turns off.
Page 91
6-37 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
6.5.8.3 [Gate Display]
The gate displays an area monitoring a target using the TT function. This equipment allows the gate
size to change automatically according to target range and size. The gate size can be checked using
the following function.
1 Click on the [Menu] button on the left toolbar.
The menu is displayed.
2 Click on the [Settings] - [TT Test] on the menu.
The "TT Test" (Test for Target Tracking) dialog is displayed.
3 Select the [Gate Display] checkbox.
When [Gate Display] is selected, the gate is displayed.
When [Gate Display] is cleared, the gate is not displayed.
4 Set the cursor mode to the AUTO mode.
Page 92
Section 6 Target Tracking and AIS 6-38
5 Click on the target of tracking whose numerical value is to be displayed.
Numeric data for the specified target is displayed in the information monitoring window.
The numeric value for the target is displayed, and the gate is displayed in green around the
target tracking symbol.
Memo
The Target Tracking can display the gate of two targets simultaneously.
Tracked
target symbol
Echo
Gate (displayed in green)
Vector
Page 93
6-39 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
6.5.8.4 Status display
The status of the TT function is displayed.
1 Click on the [Menu] button on the left toolbar.
The menu is displayed.
2 Click on the [Settings] - [TT/AIS] - [TT Test] on the menu.
The "TT Test" (Test for Target Tracking) dialog is displayed.
3 Check the display of [Status].
[Vector Constant] : Vector response
[VD Level Mode (Manual)] : Using quantization level on manual acquisition
[VD Level (Manual)] : Quantization level on manual acquisition
[Video Level (Auto)] : Quantization level on automatic acquisition
[Gate Size] : Size of gate used for tracking
[Tracking] : Number of targets currently acquired
Page 94
Section 6 Target Tracking and AIS 6-40
6.6 Setting and Operating AIS
6.6.1 Enabling AIS Function
Note
•
When the AIS function is set to Off, the AIS display function is turned off and AIS symbols are
no longer displayed.
• Once AIS function is set to Off, even If a dangerous target exists, the function
is not
automatically switched to On.
1 Click on the [AIS] button for other ship information on the upper right of PPI.
The button indication becomes ON and the AIS function becomes enabled.
ON indication:
The received AIS information is displayed on the screen.
6.6.2 Activating AIS targets (Activate AIS)
Activates an AIS target, and displays the target's vector and make a collision decision.
6.6.2.1 Manual activation
Activates an AIS target in manual mode to display the vector and heading line.
1 Set the cursor mode to the AUTO mode.
2 Place the cursor on the sleeping AIS symbol to be activated and then click on.
The selected AIS target is activated.
Page 95
6-41 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
6.6.2.2 Automatic activation
Activate an AIS target in automatic mode to display the vector and heading line.
When the automatic activation function is used, AIS targets are automatically activated when they go
into the automatic activation zone. The automatic activation zone is identical to the automatic
acquisition zone (AZ) used for target tracking. For the zone setting, refer to "6.5.1.1 Automatic
acquisition ".
Note
When the AIS target's symbol is activated but the
vector is not displayed, the following are
probable causes of the trouble:
• COG/SOG is not input yet from the GPS.
• The selected speed sensor is malfunctioning.
Memo
The bearing or range in the acquisition/activation zone shall be based on the position of the radar
antenna.
If there are more AIS targets than the allowable maximum, they are deactivated from the
low-priority (Refer to "6.3 Displaying Symbols").
6.6.3 Deactivating AIS targets
Deactivates an AIS target and clear the display of the vector and heading line.
[Deactivating one AIS target]
1 Right-click on the AIS target to be deactivated.
The setting items for cursor modes are displayed.
2 Click on the [Deactivate] on the Context menu.
The selected AIS target is deactivated.
[Deactivating multiple AIS targets]
1 Right-click on the AIS target.
The setting items for cursor modes are displayed.
2 Click on the [Deactivate mode] on the Context menu.
The cursor changes to the selection cursor.
3 Click on the AIS target to be deactivated.
The selected AIS target is deactivated.
Note
This operation is available only for an activated AIS target.
Page 96
Section 6 Target Tracking and AIS 6-42
6.6.4 Displaying AIS information
1 Set the cursor mode to the AUTO mode.
2 Place the cursor on the AIS target to display the activated AIS target information and
then click on.
The information of the selected AIS target is displayed.
Note
When the numeric data of a target is displayed but the mark " " is not on the radar display,
the target is outside the display.
Page 97
6-43 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Canceling AIS target information display
1 Set the cursor mode to the AUTO mode.
2 Move the cursor to and click on the activated AIS target whose AIS target information
is to be cancelled.
The information display of the selected AIS target is canceled.
Details on AIS target information
Two AIS target information display modes are available, a standard mode, and an extended mode,
and the items that are displayed vary depending on the mode.
Use the AIS Standard/Extended selector button for switching between the standard mode and the
extended mode.
For verifying more detailed information of the AIS target, refer to "2.3.1.4 AID Detail INFO".
The display contents vary depending on the types of AIS targets.
When the AIS Standard/Extended
selector button is clicked to change
display to , extended mode is
entered.
When the button is clicked to change
display to , standard mode is
entered.
Page 98
Section 6 Target Tracking and AIS 6-44
[Normal AIS target]
Item
Explanation
AIS ID
ID No. of AIS target
Name
Ship name of AIS target
Call Sign
Call sign of AIS target
MMSI
Maritime Mobile Service Identity
COG or CTW COG: Course Over the Ground
CTW: Course Through Water
* In ground mode, COG is displayed. In water mode, CTW is displayed.
* Operates in fixed ground mode on the ECDIS screen.
SOG or STW SOG: Speed Over the Ground
STW: Speed Through Water
*If the SOG or STW column is Over, the speed of other system is 102.2 kn or
more.
* In extended mode, the display area for two simple modes is used.
* Operates in fixed ground mode on the ECDIS screen.
CPA
Closest approach distance
TCPA
Time up to closest approach distance
BRG True direction
* In standard mode, this item is not displayed.
Range Distance
* In standard mode, this item is not displayed.
Heading Heading
* In standard mode, this item is not displayed.
Page 99
6-45 Section 6 Target Tracking and AIS
1
2 3 4
5 6 7
8 9 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Item
Explanation
ROT Rate of turn
* In standard mode, this item is not displayed.
* If the ROT column is blank, it indicates that ±127 is received. At this time, only
turning direction indicated on the turn indicator is reliable. The turn indicator is
displayed as a straight line normal to the heading direction on the AIS symbol.
(Refer to "6.3 Displaying Symbols.")
POSN Latitude/longitude
* In standard mode, this item is not displayed.
>10m or <10m >10m: Low positioning accuracy
<10m: High positioning accuracy
* In standard mode, this item is not displayed.
Destination Destination
* In standard mode, this item is not displayed.
Navigation
Status
The status is displayed by number.
For the details, refer to "Navigation Status" table.
* In standard mode, this item is not displayed.
Memo
In the extended mode, a display area equivalent to two standard mode areas is used.
Navigation Status
Status
0: Under Way Using Engine
1: at Anchor
2: Not Under Command
3: Restricted Maneuverability
4: Constrained by Her Draught
5: Moored
6: Aground
7: Engaged in Fishing
8: Under Way Sailing
9: Reserved for HSC
10: Reserved for WIG
11-14: Reserved
15: Not Defined
Page 100
Section 6 Target Tracking and AIS 6-46
[AIS SARTTarget]
There is neither the Call Sign nor Destination item. The display of some items of Navigation Status is
different. Otherwise, the display contents are the same as those of usual AIS target.
Navigation Status
Display
0 ~ 13: Same display as for the usual ship
14: AIS-SART ACTIVE(14)
15: AIS-SART TEST(15)
Memo
Switching between standard and extended modes is not provided.
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use