Jonsered J630ES, 96192006600 Parts Manual

J630ES

Part's Manual

Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine.

The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty.

585 49 64-27 Rev. 2

REPAIR PARTS SNOW THROWER - MODEL J630ES (96192006600)
AUGER HOUSING / IMPELLER ASSEMBLY

5

11

6

11

7

11

12

13

8

4

11

3

12

10

14

1

9

34

2

30

9

34

9

29

31

27

28

28

24

17

33

18

19

20

26

23

25

32

15

16

18

22

21

20

19

2 (EXPLODED)

01.07.032-A

22

REPAIR PARTS SNOW THROWER - MODEL J630ES (96192006600)
AUGER HOUSING / IMPELLER ASSEMBLY

KEY PART
NO. NO. DESCRIPTION

1 532 18 41-05 IMPELLER
2 584 64 83-01 GEARBOX ASSEMBLY
3 532 18 89-09 BEARING
4 585 09 32-01 IMPELLER PULLEY
5 532 44 24-38 DISCHARGE BASE
6 532 18 40-95 CORNER BRACKET
7 532 19 21-99 CLEAN OUT TOOL
8 532 40 54-00 TOOL CLIP
9 873 80 04-00 NUT 1/4-20
10 874 78 04-26 SCREW 1/4-20 X .625
11 532 42 79-42 NUT 5/16-18
12 532 16 31-83 SCREW 5/16-18 X .625
13 532 18 03-55 CARRIAGE BOLT
14 532 19 41-89 SCREW 13-16 X .625
15 532 40 77-60 PLUG
16 532 42 73-02 GEARBOX COVER RH
17 532 42 73-45 GASKET
18 532 40 77-70 SEAL
19 532 40 77-62 BEARING
20 532 17 46-97 THRUST WASHER 1.00
21 580 36 41-01 WORM GEAR
22 532 40 77-64 AUGER SHAFT
23 532 18 92-82 SQUARE KEY
24 532 40 77-58 BEARING
25 532 17 46-83 THRUST WASHER
26 584 64 84-01 IMPELLER SHAFT
27 532 18 42-05 ROLL PIN
28 532 17 46-81 THRUST WASHER
29 532 17 46-84 THRUST BEARING
30 532 40 77-69 BEARING
31 532 40 77-68 O-RING
32 532 40 77-67 SCREW 5/16-18 X .750
33 532 42 73-17 GEARBOX COVER LH
34 532 19 20-90 SHEAR BOLT

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

23

REPAIR PARTS SNOW THROWER - MODEL J630ES (96192006600)
AUGER HOUSING / IMPELLER ASSEMBLY

1

KEY PART
NO. NO. DESCRIPTION

1 532 40 82-70 AUGER HOUSING
2 532 40 76-45 SCRAPPER BAR
3 872 27 05-05 CARRIAGE BOLT 5/16−18 X .625
4 532 15 53-77 NUT 5/16−18

3 (5x)

4 (5x)

2

01.07.003-A

2

1

KEY PART
NO. NO. DESCRIPTION

1 532 42 11-24 AUGER ASSEMBLY 30 LH
2 532 42 11-25 AUGER ASSEMBLY 30 RH

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

01.07.019-A

24

REPAIR PARTS SNOW THROWER - MODEL J630ES (96192006600)
AUGER HOUSING / IMPELLER ASSEMBLY

4

3

2

3

KEY PART
NO. NO. DESCRIPTION

1 532 18 40-93 SKID PLATE LH
2 532 18 40-94 SKID PLATE RH

4

01.11.001-C

1

4

1

3 872 27 05-06 CARRIAGE BOLT 5/16−18 X .75
4 532 42 79-42 NUT 5/16−18

2

3

4

2

3

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

1

5

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

01.07.029-B

5

KEY PART
NO. NO. DESCRIPTION

1 532 18 81-70 PLASTIC RETAINER
2 532 42 77-62 AUGER BALL BEARING
3 532 17 95-82 SCREW 5/16−18 X 1.00
4 874 78 04-26 SCREW 1/4−20 X .625
5 873 80 04-00 NUT 1/4-20

25

REPAIR PARTS SNOW THROWER - MODEL J630ES (96192006600)
AUGER HOUSING / IMPELLER ASSEMBLY

5

2

1

3

4

5

01.16.001-B

2

1

4

3

KEY PART
NO. NO. DESCRIPTION

1 532 18 47-47 DRIFT CUTTER BAR
2 872 27 05-06 CARRIAGE BOLT 5/16−18 X .750
3 532 17 92-46 PLASTIC WASHER
4 810 04 05-00 LOCKWASHER 5/16
5 532 12 86-38 NUT 5/16−18

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

26

REPAIR PARTS SNOW THROWER - MODEL J630ES (96192006600)
CONTROL PANEL / DISCHARGE CHUTE

5

7

15

16

KEY PART
NO. NO. DESCRIPTION

1 532 44 36-80 CHUTE WELDMENT
2 532 18 45-34 DEFLECTOR WELDMENT
3 585 27 17-01 DEFLECTOR CONTROL ASSEMBLY
4 532 42 03-25 DEFLECTOR SEAL
5 532 41 42-80 KNOB BLACK
6 532 12 84-15 POP RIVET
7 817 54 10-08 SCREW 10-24 X .625
8 532 43 03-24 CHUTE SNOW SHIELD
9 532 42 17-28 SHIELD RETAINER STRAP
*10 532 17 98-29 SHOULDER BOLT 1/4-20 X .375
*11 532 19 17-30 NUT 1/4-20
*12 872 25 05-05 CARRIAGE BOLT 3/8-16 X .625
*13 532 75 11-53 NUT 5/16-18
*14 532 18 45-05 DEFLECTOR SPRING
15 532 42 06-79 (SERVICE PART) DEFLECTOR CONTROL
16 585 27 16-01 (SERVICE PART) DEFLECTOR CABLE BLACK

3

*14

1

6

01.09.015-D

*11

2

4

6

8

*10

6

*13

*12

9

NOTE:

1. ALL ITEMS INDICATED WITH AN * ARE PROVIDED IN THE BAG OF ITEMS SHIPPED LOOSE WITH PRODUCT.

2. ITEMS 15 AND 16 ARE SERVICE PART NUMBERS TO ALLOW PURCHASE OF INDIVIDUAL ITEMS IF NECESSARY.

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

27

REPAIR PARTS SNOW THROWER - MODEL J630ES (96192006600)
CONTROL PANEL / DISCHARGE CHUTE

2

2

1

*3

*7

*6

*4

01.09.010-C

KEY PART
NO. NO. DESCRIPTION

1 532 42 82-72 LEVER/CABLE ROTATOR ASSEMBLY
2 817 54 10-08 SCREW 10-24 X .625
*3 532 42 06-78 ROTATOR HEAD
*4 532 40 59-32 ROTATOR PIVOT BRACKET
*5 532 42 06-75 PULLEY PIVOT
*6 532 42 82-73 CABLE ASSEMBLY ADJUSTABLE
*7 532 42 83-10 CABLE ASSEMBLY HEAT SHIELD

NOTES:

1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.

*5

1

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

2

KEY PART
NO. NO. DESCRIPTION

1 532 43 86-26 STEER CABLE
2 874 04 10-24 SCREW 10−24 X 1.50

01.15.016-A

28