Jenn-Air JDTSS246GM User Manual

Product and Cabinet Opening Dimensions

237/8"

(606 mm)

30"

(762 mm)

/2" (851 mm) min. with

wheels

removed

/2" - 41/2"

(88 mm - 106 mm)

For 4" (100 mm) toe kick, height of cabinet opening is 341/2" (863 mm).

241/2"

(622 mm)

/4"

(19 mm)

30"

(762 mm)

/4"

(94 mm)

21"

(533 mm)

A. Insulation may be compressed (not used on all models). B. For panel-ready models, dishwasher depth is 24" (610 mm),

not including the 3/4" (19 mm) custom door panel.

C. Door handles may protrude forward of the face of the

dishwasher, varies by model.

34"

(864 mm)

(102 mm)

D. Measured from the lowest point on the underside

of the countertop. May be reduced to 331/2" (851 mm) by removing the wheels and perforated area of insulation (blanket) on dishwasher.

E. Minimum, measured from narrowest point

of opening

(76 mm)

24"

(620 mm)

24"

(64 mm)

/4"

(44 mm)

Check that all surfaces have no protrusions that would prohibit dishwasher installation.

NOTE: Shaded areas

of cabinet walls show where utility

/2"

(267 mm)

/4"

connections may be installed.

(172 mm)

/4"

(159 mm)

/4"

(51 mm)

DRAIN REQUIREMENTS

■ A new drain hose is supplied with your dishwasher.

If drain hose is not long enough, use a new drain hose with a maximum length of 12 ft (3.7 m) that meets all current AHAM/ IAPMO test standards, is resistant to heat and detergent, and ﬁts the 1" (25 mm) drain connector of the dishwasher. See the “Tools and Parts” section at the front of the guide for part details and orders.

NOTE: Do not connect multiple drain hoses together.

■ Make sure to connect drain hose to waste tee or disposer

inlet above drain trap in house plumbing and 20" (508 mm) minimum above the ﬂoor. It is recommended that the drain hose either be looped up and securely fastened to the underside of the counter or be connected to an air gap.

■ Make sure to use an air gap if the drain hose is connected

to house plumbing lower than 20" (508 mm) above subﬂoor or ﬂoor.

Use of air gap

Air gap

ELECTRICAL REQUIREMENTS

Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/NFPA 70 - latest edition, and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association 1 Batterymarch Park Quincy, MA 02169-7471

You Must Have:

■ 120-volt, 60 Hz, AC-only, 15- or 20-amp, fused

electrical supply

■ Copper wire only

■ A maximum of 2 ﬁeld wiring supply conductors

(12 AWG largest size) plus 1 grounding conductor are permitted in the terminal box.

We Recommend:

■ A time-delay fuse or circuit breaker

■ A separate circuit

If Connecting Dishwasher with a Power Cord:

■ Use UL Listed power cord kit marked for

use with dishwasher. See the “Tools and Parts” section at the front of the guide for part details and orders.

■ Plug into a grounded 3 prong outlet. Outlet must

meet all local codes and ordinances.

■ If required, the air gap should be installed in accordance

with the air gap installation instructions. When you are connecting the air gap, a rubber hose (not provided) will be needed to connect to the waste tee or disposer inlet.

■ Use

/2" minimum I.D. drain line ﬁttings.

WATER SUPPLY REQUIREMENTS

■ This dishwasher has a water heating feature and also

requires a connection to a hot water supply line.

■ A hot water line with 20 to 120 psi (138 to 862 kPa)

water pressure can be veriﬁed by a licensed plumber.

■ 120°F (49°C) water at dishwasher

■

/8" O.D. copper tubing with compression ﬁtting or ﬂexible braided water supply line. See the “Tools and Parts” section at the front of the guide for part details and orders.

NOTE: 1/2" minimum plastic tubing is not recommended.

■ A 90° elbow with

See the “Tools and Parts” section at the front of the guide for part details and orders.

■ Do not solder within 6" (152 mm) of the water inlet valve.

■ If installed in new construction, make sure the house

water supply lines have been ﬂushed prior to connecting the dishwasher to remove any debris that may exist in the supply line.

NOTE: If replacing an existing dishwasher, it is recommended to install a new water line (see the “Tools and Parts” section at the front of the guide for part details) and drain hose (supplied) with the new dishwasher.

/4" hose connection with rubber washer.

If Connecting Dishwasher with Direct Wiring:

■ Use ﬂexible, armored, or nonmetallic

sheathed copper wire with grounding wire that meets the wiring requirements for your home and local codes and ordinances.

■ Use a UL Listed/CSA Approved metallic strain relief.

See the “Tools and Parts” section at the front of the guide for part details and orders.