Jbsystems light FROG LASER User Manual
WWW.BEGLEC.COM
Operation Manual
Mode d'emploi
Gebruiksaanwijzing
Bedienungsanleitung
Manual de instrucciones
Manual do utilizador
EN
FR
NL
DU
ES
PT
Reproduction or publication of the content in any manner, without express permission of the publisher, is prohibited.
Copyright © 2006 by BEGLEC cva.
Version: 1.0
EN - DISPOSAL OF THE DEVICE
Dispose of the unit and used batteries in an environment friendly manner
according to your country regulations.
FR - DÉCLASSER L’APPAREIL
Débarrassez-vous de l’appareil et des piles usagées de manière écologique
Conformément aux dispositions légales de votre pays.
NL - VERWIJDEREN VAN HET APPARAAT
Verwijder het toestel en de gebruikte batterijen op een milieuvriendelijke
manier conform de in uw land geldende voorschriften.
DU - ENTSORGUNG DES GERÄTS
Entsorgen Sie das Gerät und die Batterien auf umweltfreundliche Art und
Weise gemäß den Vorschriften Ihres Landes.
ES - DESHACERSE DEL APARATO
Reciclar el aparato y pilas usadas de forma ecologica conforme a las
disposiciones legales de su pais.
PT - COMO DESFAZER-SE DA UNIDADE
Tente reciclar a unidade e as pilhas usadas respeitando o ambiente e em
conformidade com as normas vigentes no seu país.
ENGLISH USER MANUAL
Thank you for buying this JB Systems product. To take full advantage of all possibilities
and for your own safety, please read these operating instructions very carefully before you
start using this unit.
FEATURES
This unit is radio-interference suppressed. This product meets the requirements of the
current European and national guidelines. Conformity has been established and the
relevant statements and documents have been deposited by the manufacturer.
• This device has been designed to produce decorative effect lighting and is used in light
show systems.
• 4.9mW Green Laser
• Several working modes:
o
Stand alone audio mode with built-in microphone
o
Stand alone automatic mode
o
Stand alone manual pattern select mode
• 36 preprogrammed shows laser patterns
• Full beam and dotted beam patterns
• Complies to EN/IEC 60825-1 for Laser Safety
BEFORE USE
• Before you start using this unit, please check if there’s no transportation damage. Should
there be any, do not use the device and consult your dealer first.
•
Important:
absolutely necessary for the user to strictly follow the safety instructions and warnings in
this user manual. Any damage caused by mishandling is not subject to warranty. The
dealer will not accept responsibility for any resulting defects or problems caused by
disregarding this user manual.
• Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to
add this user manual.
Check the contents:
Check that the carton contains the following items:
• FROG Laser unit
• AC/DC Mains adapter
• Operating instructions
This device left our factory in perfect condition and well packaged. It is
ENGLISH USER MANUAL
SAFETY INSTRUCTIONS:
• To protect the environment, please try to recycle the packing material as much as
possible.
• To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
• To avoid condensation to be formed inside, allow the unit to adapt to the surrounding
temperatures when bringing it into a warm room after transport. Condense sometimes
prevents the unit from working at full performance or may even cause damages.
• This unit is for indoor use only.
• Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may
result. If a foreign object enters the unit, immediately disconnect the mains power.
• Locate the fixture in a well ventilated spot, away from any flammable materials and/or
liquids. The fixture must be fixed at least 50cm from surrounding walls.
• Don’t cover any ventilation openings as this may result in overheating.
• Prevent use in dusty environments and clean the unit regularly.
• Keep the unit away from children.
• Inexperienced persons should not operate this device.
• Maximum save ambient temperature is 45°C. Don’t use this unit at higher ambient
temperatures.
• Make sure the area below the installation place is free from unwanted persons during
rigging, de-rigging and servicing.
• Allow the device about 10 minutes to cool down before replacing the bulb or start
servicing.
• Always unplug the unit when it is not used for a longer time or before replacing the bulb
or start servicing.
• The electrical installation should be carried out by qualified personal only, according to
the regulations for electrical and mechanical safety in your country.
• Check that the available voltage is not higher than the one stated on the rear panel of the
unit.
• The power cord should always be in perfect condition: switch the unit immediately off
when the power cord is squashed or damaged.
• Never let the power-cord come into contact with other cables!
• This fixture must be earthed to in order comply with safety regulations.
• Don’t connect the unit to any dimmer pack.
• Always use an appropriate and certified safety cable when installing the unit.
• In order to prevent electric shock, do not open the cover. Apart from the lamp and mains
fuse there are no user serviceable parts inside.
• Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a
fuse of the same type and electrical specifications!
• In the event of serious operating problems, stop using the fixture and contact your dealer
immediately.
• The housing and the lenses must be replaced if they are visibly damaged.
• Please use the original packing when the device is to be transported.
• Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important: Never look directly into the light source! Don’t use the effect in the presence of
persons suffering from epilepsy.
JB SYSTEMS® 1/36 FROG Laser
JB SYSTEMS® 2/36 FROG Laser
ENGLISH USER MANUAL
LASER SAFETY INSTRUCTIONS:
• According to the EN 60825-1:1994 + A1:2002 + A2:2002 regulations, this laser falls
under the classification 3R. Direct eye exposure can be dangerous.
• This product is a so-called show laser, emitting radiation with a wavelength spectrum
between 400 and 700 nm and producing lighting effects for shows.
• Due to the construction of this laser, the beam is moved so fast, that it can only hit the
eye very short. This is why the use of this laser for a Laser-Light-Show can be regarded
as save.
• Never direct the laser beam to people or animals and never leave this device running
unattended.
• This laser may only be used for shows. The operation of a class 3R show laser is only
allowed if the operation is controlled by a skilled and well-trained operator.
• Depending on the classification, operating a laser product can produce laser radiation
that may cause permanent eye damage and/or skin damage. The legal instructions for
using a laser product vary from country to country. The user must always inform himself
on the legal instructions valid in his country and apply them to his situation.
Please note that
installations and unskilled operation!
Avoid direct eye exposure! Laser radiation can cause eye damage
and/or skin damage. All protective measures for a safe operation of
JB SYSTEMS
DANGER: LASER RADIATION !
this laser must be applied.
cannot be made liable for damages caused by incorrect
DESCRIPTION:
1. DC 9V INPUT: this input is used to
connect the AC/DC adapter.
2. ON/OFF SWITCH: used to switch the
unit on/off. Make sure you have fully
read and understood all safety related
issues in this user manual before you
switch on the laser!
3. AUDIO SENSITIVITY: when the laser
is set to audio mode you can adapt the
sensitivity of the built-in microphone to
obtain optimal performance.
4. MODE SWITCH: used to set the unit
in one of the 3 available modes.
5. PATTERN SELECTOR: when the unit
is used in manual pattern mode, you
can select the preprogrammed
patterns by pressing this button.
6. INTERNAL MICROPHONE: The built-
in microphone is used to synchronize
the laser show to the music.
ENGLISH USER MANUAL
7. AC/DC ADAPTER: adapter to convert the 230Vac mains input to the 9Vdc needed for
the FROG laser.
8. WARNING LABELS: “Caution – Class 3R laser. Laser Radiation when open. Avoid
exposure to beam.”
9. LASER OUTPUT: On the front of the enclosure there’s a large opening where the laser
beam leaves the enclosure, make sure to NEVER look inside the unit through this
opening while the laser effect is switched on!
10. HANGING BRACKET: with 2 screws on both sides to fasten the unit and a mounting
hole to fix a mounting hook.
OVERHEAD RIGGING
•
Important: The installation must be carried out by qualified service personal only.
Improper installation can result in serious injuries and/or damage to property.
Overhead rigging requires extensive experience! Working load limits should be
respected, certified installation materials should be used, the installed device
should be inspected regularly for safety.
• Make sure the area below the installation place is free from unwanted persons during
rigging, de-rigging and servicing.
• Locate the fixture in a well ventilated spot, far away from any flammable materials and/or
liquids. The fixture must be fixed
• The device should be installed out of reach of people and outside areas where persons
may walk by or be seated.
• Before rigging make sure that the installation area can hold a minimum point load of
10times the device’s weight.
• Always use a certified safety cable that can hold 12times the weight of the device when
installing the unit. This secondary safety attachment should be installed in a way that no
part of the installation can drop more than 20cm if the main attachment fails.
• The device should be well fixed; a free-swinging mounting is dangerous and may not be
considered!
• Don’t cover any ventilation openings as this may result in overheating.
• The operator has to make sure that the safety-relating and machine-technical
installations are approved by an expert before using them for the first time. The
installations should be inspected every year by a skilled person to be sure that safety is
still optimal.
at least 50cm
CAUTION EYEDAMAGE: Always position the laser in a way that
prevents the audience from looking directly into the laser beams. The
installation should assure that the beam will not strike the audience.
from surrounding walls.
JB SYSTEMS® 3/36 FROG Laser
JB SYSTEMS® 4/36 FROG Laser
ENGLISH USER MANUAL
HOW TO SET UP AND CONTROL THE UNIT
• Regular breaks during operation are essential to maximize the life of this device as it is
not designed for continual use.
• Do not switch the unit on and off in short time intervals as this reduces the lamp life.
• Always unplug the unit when it is not used for a longer time. or before replacing the bulb
or start servicing.
• In the event of serious operating problems, stop using the fixture and contact your dealer
immediately.
•
Important:
of persons suffering from epilepsy.
You can operate the unit in 3 ways:
1) STAND ALONE AUDIO MODE
• Put the mode switch in the left position (audio)
• Switch the unit on.
• Put on some rhythmic music at the desired level.
• Adjust the music sensitivity potentiometer.
The FROG LASER projects the different laser patterns following the rhythm of the music.
2) STAND ALONE AUTOMATIC MODE
• Put the mode switch in the middle position (auto)
• Switch the unit on.
The FROG LASER projects the different laser patterns automatically.
3) STAND ALONE MANUAL PATTERN SELECT MODE
• Put the mode switch in the right position (manual)
• Switch the unit on.
• The FROG LASER projects one of the 36 pre-programmed patterns until you press the
“pattern select” button to go to the next pattern…
Never look directly into the laser beam! Don’t use the effect in the presence
ENGLISH USER MANUAL
• The cleaning of internal and external optical lenses and/or mirrors must be carried out
periodically to optimize light output. Cleaning frequency depends on the environment in
which the fixture operates: damp, smoky or particularly dirty surroundings can cause
greater accumulation of dirt on the unit’s optics.
• Clean with a soft cloth using normal glass cleaning products.
• Always dry the parts carefully.
• Clean the external optics at least once every 30 days.
• Clean the internal optics at least every 90 days.
Attention:
personnel!
SPECIFICATIONS
Power input: 9Vdc (>800mA)
AC/DC power adapter: AC 230V,50Hz Æ 9Vdc (800mA or more)
Sound Control: Internal microphone
Laser Power: 4.9mW Green CW laser (λ = 532nm)
Laser radiation class: 3R
Laser Safety Standard: EN60825-1:1994 + A1:2002 + A2:2002
Size: 143 x 160 x 75mm
Weight: 0,81kg
We strongly recommend internal cleaning to be carried out by qualified
Every information is subject to change without prior notice
MAINTENANCE
• Make sure the area below the installation place is free from unwanted persons during
servicing.
• Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
• All screws used for installing the device and any of its parts should be tightly fastened
and may not be corroded.
• Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally
free from any deformation.
• When an optical lens is visibly damaged due to cracks or deep scratches, it must be
replaced.
• The mains cables must be in impeccable condition and should be replaced immediately
when even a small problem is detected.
• In order to protect the device from overheat the cooling fans (if any) and ventilation
openings should be cleaned monthly.
• The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
JB SYSTEMS® 5/36 FROG Laser
JB SYSTEMS® 6/36 FROG Laser
FRANÇAIS MODE D’EMPLOI
FRANÇAIS MODE D’EMPLOI
Merci d’avoir choisi ce produit JB Systems. Pour votre sécurité et pour une utilisation
optimale de toutes les possibilités de l’appareil, lisez attentivement cette notice avant
utilisation.
CARACTERISTIQUES
Cet appareil ne produit pas d’interférences radio. Il répond aux exigences nationales et
européennes. La conformité a été établie et les déclarations et documents correspondants
ont été déposés par le fabricant.
• Cet appareil a été conçu pour la production d’effets lumière décoratifs et est utilisé dans
des spectacles lumineux.
• Laser 4.9mW vert
• Plusieurs modes de fonctionnement:
o
Mode autonome avec microphone incorporé
o
Mode autonome automatique
o
Mode autonome avec sélection manuelle des motifs
• 36 motifs préprogrammés
• Motifs de faisceaux pleins et faisceaux pointillés
• En accord avec les normes EN/IEC 60825-1 pour la Sécurité Laser
AVANT UTILISATION
• Avant d’utiliser cet appareil, assurez-vous de l’absence de dommage lié au transport. En
cas d’endommagement, n’utilisez pas l’appareil et contactez le vendeur.
• Important: Cet appareil a quitté notre usine en parfaite condition et bien emballé. Il est
primordial que l’utilisateur suive les instructions de sécurité et avertissements inclus dans
ce manuel. La garantie ne s’applique pas en cas de dommage lié à une utilisation
incorrecte. Le vendeur ne prend pas la responsabilité des défauts ou de tout problème
résultant du fait de n’avoir pas tenu compte des mises en garde de ce manuel.
• Conservez ce manuel dans un endroit sûr pour toute consultation future. Si vous vendez
l’appareil, assurez-vous d’y joindre ce manuel également.
Vérifiez le contenu:
Vérifiez si l’emballage contient les articles suivants:
• FROG Laser unit
• Adaptateur secteur AC/DC
• Mode d'emploi
INSTRUCTIONS DE SECURITE:
• Afin de protéger l’environnement, merci de recycler les emballages autant que possible.
• Afin d’éviter tout risque d’incendie ou de choc électrique, ne pas exposer cet appareil à
la pluie ou l’humidité.
• Pour éviter la formation de condensation à l’intérieur de l’appareil, patientez quelques
minutes pour laisser l’appareil s’adapter à la température ambiante lorsqu’il arrive dans
une pièce chauffée après le transport. La condensation empêche l’unité de fonctionner
en performance optimale et peut même causer des dommages.
• Cette unité est destinée à une utilisation à l’intérieur uniquement.
• Ne pas insérer d’objet métallique ou verser un liquide dans l’appareil. Risque de choc
électrique ou de dysfonctionnement. Si un corps étranger est introduit dans l’unité,
déconnectez immédiatement de la source d’alimentation.
• Placez l’appareil dans un endroit bien ventilé, éloigné de tout matériau ou liquide
inflammable. L’appareil doit être fixé à 50 cm minimum des murs.
• Ne pas couvrir les ouvertures de ventilation, un risque de surchauffe en résulterait.
• Ne pas utiliser dans un environnement poussiéreux et nettoyez l’unité régulièrement.
• Ne pas laisser l’unité à portée des enfants.
• Les personnes non expérimentées ne doivent pas utiliser cet appareil.
• La température ambiante maximum d’utilisation de l’appareil est de 45°C. Ne pas
l’utiliser au-delà de cette température.
• Assurez-vous que la zone au-dessous du lieu d’installation ne comporte pas de
personnes indésirables pendant le montage, le démontage et les opérations de
maintenance.
• Laissez l’appareil refroidir environ 10 minutes avant de remplacer l’ampoule ou
d’effectuer des réparations.
• Débranchez toujours l’appareil si vous ne l’utilisez pas de manière prolongée, avant de
changer une ampoule ou d’entreprendre des réparations.
• Les installations électriques ne peuvent être faites que par du personnel qualifié et
conformément aux régulations de sécurité électrique et mécanique en vigueur dans
votre pays.
• Assurez-vous que le voltage de la source d’alimentation de la zone dans laquelle vous
vous trouvez ne dépasse pas celui indiqué à l’arrière de l’appareil.
• Le cordon d’alimentation doit toujours être en condition parfaite. Mettez immédiatement
l’unité hors tension si le cordon est écrasé ou endommagé.
• Ne laissez jamais le cordon d’alimentation entrer en contact avec d’autres câbles !
• L’appareil doit être à la masse selon les règles de sécurités.
• Ne pas connecter l’unité à un variateur de lumière.
• Utilisez toujours les câbles appropriés et certifiés lorsque vous installez l’unité.
• Pour éviter tout choc électrique, ne pas ouvrir l’appareil. En dehors des ampoules et du
fusible principal, il n’y a pas de pièces pouvant être changées par l’utilisateur à l’intérieur.
• Ne jamais réparer ou court-circuiter un fusible. Remplacez systématiquement un
fusible endommagé par un fusible de même type et spécifications électriques !
• En cas de problèmes de fonctionnement sérieux, arrêtez toute utilisation de l’appareil et
contactez votre revendeur immédiatement.
• La coque et les lentilles doivent être remplacées si visiblement endommagées.
• Utilisez l’emballage d’origine si l’appareil doit être transporté.
JB SYSTEMS® 7/36 FROG Laser
JB SYSTEMS® 8/36 FROG Laser
Loading...