Page 1
Item no.
69466
26.01
Page 2
1
2
D 8SUB
D 8ADD
D 8SUR
Surround EX
4
Page 3
3
D 8SUR
5
Page 4
D 8CEN - a D 8CEN - b
6
Page 5
4
Front
Surround
D 8SUR
D 8CEN
Front
D 8SUB
Surround
D 8SUR
Surround
EX
7
Page 6
5
Sub
Line out
D 8SUB
6
D 8SUB
8
Page 7
7 8
www.jamospeakers.com
9
Page 8
9
Type...............................................................D 8SUR
System................................2 Way Bipole/Dipole
Woofer......................................2 x 5¼ / 133 mm
Tweeter............................................2 x 1 / 25 mm
Power handling*........................150W / 200W
Frequency range....................50 - 20.000 Hz
Impedance................................................6 Ohm
Dimensions........................272x256x194mm
10,7x10,1x7,6in
Weight.........................................5,4 kg / 11,9 lb
Type...........................................................D 8CEN
Sytem....................3 Way Aperiodic Champer
Woofer.......................................2 x 6½ / 165 mm
Midrange..........................................1½ / 38 mm
Tweeter..............................................1 / 25 mm
Type.............................................................D 8SUB
System..........................Active subwoofer
Woofer.............................................12 / 305 mm
Amp. Rated output...............................400W
Frequency range.............................28 - 120 Hz
Upper cutoff frequency......Adj. 40 - 120 Hz
Maximum SPL......................................107 dB
Phase.................................Adjustable 0 - 180°
Dimensions.......................407x454x454mm
16,0x17,9x17,9in
Weight..........................................20,1 kg / 44,3 lb
Power handling*..........................110W / 150W
Frequency range...................65 - 20.000 Hz
Impedance................................................4 Ohm
Dimensions..................217x555x285mm
8,5x21,9x11,2in
Weight.........................................10,8 kg / 23,8 lb
10
Specifications subject to technical changes.
*Long / Short term power, According to IEC 268-5.
Page 9
D 8ADD
Advanced Owners Manual
Page 10
GB
Introduction
Congratulations on your choice of Jamo D 8. By choosing this high-end loudspeaker, you are ensured a first-rate natural sound reproduction
- that is, of course, if the rest of your system can match the loudspeakers. For you will also be able to mercilessly reveal any possible
shortcomings in the rest of the music chain as well as the music material used.
In order to get the maximum benefit it is therefore important to go through these instructions which offer good advice about installing/
connecting the units and about the acoustics of the listening room. We also tell you a little about the techniques we have used and the
decisions we have made to reach the goal - to present what it is all about - MUSIC!
A few comments on quality
To us at Jamo it is of fundamental importance that no Jamo loudspeaker is found to deviate from the reference model, irrespective of
production time.
In order to meet this requirement, all components and units must be approved within very narrow tolerances even at entry level. A
continuous quality control is performed on all semi-manufactures, and in the end all Jamo loudspeakers are put through a compulsory
final quality control before leaving the factory.
Jamos consistent high levels of quality and workmanship, and thus the uniform quality in production, are based on several factors,
notably the experience and expertise which have accumulated at Jamo since the companys start in 1968, as well as the fact that Jamo
was the first loudspeaker manufacturer in the world to obtain certification according to the strict ISO 9001 quality norm in 1992.
Unpacking
When you unpack your new loudspeakers, you might think that the glow of the cabinets and/or the colour play of the veneer do not
completely match the demonstration models that you may have seen at your Jamo dealers. However, this is just a result of the fact that
each piece of genuine veneer will have its own individual features, and since it is a natural material, you will find that the colour play and
the glow change as the loudspeakers are exposed to light and air. So in time they will look even better and have even more soul!
Remember also that loudspeakers should be broken in, that is play for some time, before they can perform at their best! If you do not
want to do this when you are at home, set your tuner between two stations, so that a hissing sound is heard from the loudspeakers. Then
leave the loud-speakers to play for a few hours at a medium sound level.
After this, the rest is up to you - we are sure that you will get many hours of fine entertainment.
Enjoy yourself!
Preben Jakobsen Jul ius Mortensen
2
Page 11
GB
Design, D 8CEN
Jamo D 8CEN was developed especially for the enthusiast who makes equally heavy demands on supreme and uncompromising
reproduction of surround sound as for hi-fi listening. As the main job of the centre speaker is to reproduce the dialogue and the action
taking place at the centre of the screen, we have given a high priority to obtaining optimum intelligibility of speech as well as powerful
reproduction of the full frequency range in the Jamo D 8CEN. This means that all the sound reproduced by the centre loudspeaker will
be clear and easy to understand - even at high sound pressures and when the dialogue is accompanied by loud explosions and other
impressive sound effects in the film sound track.
Cabinet
To obtain a dry reproduction of dialogue, a low resonance frequency is required - and usually a loudspeaker cabinet will do just the
opposite - which is to increase the resonance frequency !
Impedance curve for
a normal cabinet
The effect of the cabinet on the resonance frequency
We therefore used a special cabinet technology called
Aperiodic Chamber for the Jamo D 8CEN.
Impedance curve for
an Aperiodic Chamber
High resonance frequency
Low resonance frequency
Other than the dry reproduction, this technology also permits using large woofers in a relative small cabinet, resulting in the desired
authoritative sound. Normally, using large woofers in small cabinets will result in a frequency overshoot immediately before the woofers
low-frequency roll-off point. The consequence of this overshoot is very often perceived as a rumbling bass reproduction.
Low freq. response in a normal
cabinet (overshoot)
The effect of the cabinet on the bass reproduction
Therefore, the rear panel of an Aperiodic Chamber (cabinet)
is ventilated through holes constituting around 20% of the
Low freq. response in an Aperiodic Chamber
(natural roll off)
woofers total diaphragm area. The ventilation results in an
acoustic short-circuit of the lowest frequencies (it becomes
effective around 200 Hz).
Ventilating the cabinet dampens the overshoot, partly because of the acoustical short-circuit, and partly because of the mechanical
dampening applied to the woofers.
In an Aperiodic Chamber, the diaphragm displacement will increase in the area below the resonance frequency - this means that
although there is a low frequency short-circuit the frequency response will extend way below what is required of a centre loudspeaker.
Of course the larger diaphragm displacement calls for customised woofers with well-controlled limits of displacement.
Controlling the ventilation of an Aperiodic Chamber requires critical dampening with a large amount of acoustic absorption foam. This
in combination with the reduced rear panel area minimises the formation of standing sound waves and thereby eliminates coloration/
distortion of the sound reproduction.
The cabinet for the Jamo D 8CEN is manufactured in 25 mm MDF board with genuine veneer. The front baffle is a sandwich construction
consisting of a strong die-cast synthetic shell and 22 mm MDF board.
Tweeter and Midrange
For the Jamo D 8CEN we have chosen a 1" and a 1½ soft dome to reproduce the treble and midrange areas, respectively. Both units are
equipped with coated textile diaphragms and highly efficient neodymium magnets. The advantage of the compact size of the extremely
powerful neodymium magnets is that they can be placed inside the voice coil. This ensures that a highly concentrated magnetic field is
created exactly where it is needed. An additional advantage of this design is that the magnetic stray field is minimal, which eliminates the
need for further magnetic shielding of these units.
3
Page 12
GB
The special 1½ midrange dome has been chosen to obtain a sufficiently low crossover frequency between the bass and midrange areas
in order to ensure wide horizontal dispersion.
This is important to enable the centre loudspeaker to cover a broad listening position, when several persons are listening.
With a low crossover frequency, out of phase problems between the two woofers are avoided, allowing the required dispersion to be
realised.
In order to ensure perfect transition to the woofer, the midrange unit is fitted in a specially designed horn, which has been tuned to just
below the resonant frequency of the unit.
The horn provides a better coupling between the diaphragm and the surrounding air, which results in a linear reproduction and higher
efficiency in the lower midrange area.
Woofer
The diaphragms of the two woofers are manufactured in fibre glass, which is a rigid and quite heavy material. The relatively heavy moving
mass and the resulting low resonance frequency have been chosen partly to achieve optimum harmony with the Aperiodic Chamber
and partly to obtain the desired powerful and precise reproduction of the bass area below 1000 Hz.
The woofers frame is made in die-cast plastic. This ensures that the magnetic force stays concentrated around the voice coil instead of
spreading out into the basket. Also the magnetic strayfield is perfectly controlled, so that the loudspeaker can be placed directly on top
of a TV set without causing discoloration of the picture.
Design D 8SUR
Cabinet
The most conspicuous feature about the Jamo D 8SUR loudspeaker set is the design. The unique design was developed not only to
please the eye, but equally to satisfy the ear. Jamo D 8SUR is manufactured in 16 mm MDF board and accurately dampened with acoustic
foam. The surface of the foam is shaped in a honeycomb pattern to obtain the largest possible surface area and thus maximum
dampening of the sound radiating from the rear of the units.
To achieve optimum sound reproduction, the designs of the two loudspeakers in a pair are laterally reversed and therefore they are
available only in sets of a left and right loudspeaker (see the marking on the back of the loudspeakers).
Drive units
The treble is a soft dome tweeter.
The unit is oil cooled and has a voice coil wound of thermosetting wire on an aluminium voice coil former, for high power handling.
The woofer units have a specially woven fibre glass diaphragm. Other than the exclusive design, the special weave ensures a uniform
material thickness over the entire diaphragm.
A loudspeaker diaphragm can be compared to a piston, and to comply with the heavy demands on the diaphragm materials stretch and
compression properties, the composite fibre material is composed of four different types of glass and treated with a tough-hardening
resin. This results in a light and rigid cone with good internal damping. Combined with the natural rubber suspension, which ef-fectively
prevents vibrations from travelling back to the diaphragm, the result is a very well-controlled diaphragm that operates without break-ups
in its working range.
The units basket is made from injection moulded carbon fibre reinforced ABS. Using a non-magnetic material such as ABS ensures that
the magnetic force stays concentrated around the voice coil instead of spreading out into the basket.
As a result, the efficiency of the unit is increased, and the loudspeaker may be placed closer to a TV set without risk of discolouring the
image. Compared to a conventional metal basket, the acoustic properties are significantly improved, as the ABS material has a much
higher internal damping.
The unit has a large magnet and a heavy voice coil with a diameter of 25mm.
All these properties lead to an open and precise sound reproduction with unsurpassed attack.
Jamo D 8SUR is designed to enable a diffuse sound reproduction giving the listener the feeling of being enveloped in sound. In
conventional loudspeakers, this type of design will usually lead to a lack of efficiency in the
deep bass area.
However, in order to meet the demands of digital 5.1 sound, Jamo D 8SUR is equipped with a filter to significantly improve the bass
reproduction: at low frequencies, the loudspeaker acts as a traditional box with two woofer units working in phase, giving a bipolar
characteristic.
At high frequencies, the phase of the reproduction will gradually shift to give the loudspeaker a dipole characteristic. In other words,
Jamo D 8SUR combines the best of these two principles.
4
Page 13
GB
Installation
Placing
Jamo D 8CEN should be placed immediately above or below the TV set. This position ensures perfect integration between picture and
sound, and thus the optimum and most realistic experience.
NOTE! Because of its physical size, always make sure that the D 8CEN can be placed reliably and safely on the TV set or wherever you
intend to place it.
Mount the Jamo D 8SUR in line with the listening position, either on the side walls - approx. 2 m above the floor - or on the ceiling. When
mounting the loudspeakers on the ceiling, make sure that the top of each speaker faces the listening position. For mounting on the
ceiling, the recommended maximum ceiling height is 3 m. Be careful to place the loudspeakers at the correct side (check the LEFT /
RIGHT indication at the back of the loudspeakers).
1
Use the supplied wall brackets for wall mounting.
2
Use the supplied ceiling brackets for mounting on the
ceiling.
To obtain full benefit from the loudspeakers dipole
characteristic, it is important to ensure a minimum clearance
of 0.5 m at both sides of the loudspeakers to allow the sound
to travel freely along the wall/ceiling.
NOTE:
When mounting the loudspeakers on the wall/ceiling it is
important to use screws and rawlplugs which are appropriate
for the wall/ceiling material to ensure that the loudspeakers
are securely mounted.
5
Page 14
GB
Connecting
Jamo D 8 is equipped with gold-plated terminals which will accept heavy stripped cables. Your local Jamo dealer can advise you on
which cables to buy. In general, the longer the cable, the higher quality should be used to avoid signal loss in the cable itself. In terms of
sound quality it is therefore an advantage not to use cables which are longer than required, although the cables used to connect each of
the speakers should be roughly the same length.
If you wish to use cables with stripped ends, proceed as follows
1. Turn off the amplifier.
2. Gently strip off approximately 15 mm of the insulation on
the cable ends - be careful not to damage the cable wires.
3. Twist the wires.
4. Turn the terminal screws counterclockwise until the twisted
wires can easily be inserted into the holes.
5. Turn the terminal screws clockwise to secure the cables in
the terminals.
NOTE:
Verify that the wires from the + and - cables do not touch
each other, as a short-circuit could damage the amplifiers
output stage.
Single wiring / Bi-wiring (D 8CEN)
1
If you wish to connect each speaker with a single cable,
the supplied bridges should remain fitted between
the two sets of terminals.
The loudspeaker comes from Jamo with the bridges
fitted for single-wiring.
2
If you are using bi-wiring, remove the bridges between
the two sets of terminals.
You can connect the cables together to one set of output
terminals on the amplifier, or, if the amplifier has two
sets of output terminals, connect one cable to terminal
set A and the other cable to terminal set B.
Bi-amping (D 8CEN)
In bi-amping the loudspeakers are connected to two power amplifiers.
Here you have two options:
1. Connect amplifier 1 to the tweeter/midrange.
Connect amplifier 2 to the woofer.
(When different amplifiers are used).
- or -
2. The two amplifiers are used for the left and right channels, respectively, i.e. the tweeter/midrange units are connected to one
channel on the amplifier, and the woofer is connected to the other. (Typically when identical amplifiers are used)
Consult your Jamo dealer for further information.
Always make sure that the loudspeakers are in proper phase;
The + terminal on the loudspeaker is connected to the + terminal on the amplifier.
The - terminal on the loudspeaker is connected to the - terminal on the amplifier.
Loudspeaker cable is usually marked on one cord; this cord is normally used to connect the + terminals, this way it is easy to ensure that
the loudspeakers are in correct phase.
6
Page 15
GB
Maintenance
The scope of the warranty
The warranty period will come into force as from the purchase
date stated on the invoice. The warranty will apply for the following
period of time:
2 years for electronics (power supply, amplifier, etc.)
7 years for other parts (cabinet, speaker units, etc.)
In case of warranty inquiries, please contact your dealer.
In case of request for service under warranty, please enclose your
original receipt.
All Jamo loudspeakers are manufactured in modern and
thoroughly tested materials, which normally do not require
any maintenance other than vacuum cleaning or using a
soft, dry cloth to remove dirt.
If the loudspeakers have become greasy, you can clean
them by moistening the cloth with water or perhaps using
a mild detergent.
Note:
Never use scouring powder, petrol, ethyl alcohol or solvents
to clean the loudspeakers.
Defects not covered by the warranty:
Defects arising from accidents, misuse, normal wear and tear,
mis-maintenance, voltage variation, overloading, stroke of
lightning, and other force majeure events
Defects arising from incorrect installation or operation
Defects arising from modification/repair/attempt of repair by a
non-authorised service centre
Defects arising from the use of non-original spare parts
Defects on products with altered or lacking series number
Other defects due to conditions or circumstances beyond the
suppliers control
Defects covered by the warranty:
Except for the defects stated below, the warranty covers any
production and material defects of the product.
Transportation costs for servicing are not covered by the warranty.
The supplier is liable only to repair or replace defective parts or
products. A replacement cannot exceed the value of the product
under warranty.
7
Loading...