iRobot j7+ Owners Manual

Robot Vacuum & Mop

Robot aspirateur et laveur

Robot aspirador y trapeador

j7+

Owner’s Guide

Guide du propriétaire

Guía del usuario

Safety Information

Important Safety Information

This owner’s guide includes information for Regulatory Model(s):
Robot: RCA-Y1 | Dock: ADG-N1 | Battery: ABL-F | Radio Module: AXG-Y1

SAVE THESE INSTRUCTIONS
WARNING: When using an electrical appliance, basic precautions should always be followed,

including the following:
READ ALL INSTRUCTIONS

WARNING: To reduce the risk of injury or damage, read and follow the safety precautions
when setting up, using and maintaining your robot.

This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.

This is the safety alert symbol. It is used to alert you to potential physical injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.

Risk of electric shock Class II equipment Rated power output, d.c.

Risk of fire For indoor use only Rated power input, d.c.

Caution Rated power input, a.c.

Read operator’s
manual

Keep out of reach
ofchildren

General symbol for
recycling

Separate Supply Unit

EN

EN

WARNING: Indicates a hazardous situation that, if not avoided, could
result in death or serious injury.

CAUTION: Indicates a hazardous situation that, if not avoided, could
result in minor or moderate injury.

NOTICE:

Indicates a hazardous situation that, if not avoided, could result

in property damage.

GENERAL

WARNING

• Your robot comes with a region approved power supply cord and is
designed to be plugged into a standard household AC power outlet
only. Do not use any other power supply cord. For replacement cords,
please contact Customer Care to ensure proper selection of country
specific power supply cord.

• Do not submerge your robot in water.

• Do not open your robot except as instructed to install or replace the
battery or to perform required maintenance. Do not open the integrated
dock-charger known as Home Base or Clean Base. There are no user
serviceable parts inside. Refere servicing to qualified service personnel.

• Risk of electric shock, use indoors in dry location only.

• Do not handle your robot or charging station with wet hands.

• Do not use unauthorized chargers. Use of an unauthorized charger
could cause the battery to generate heat, smoke, catch fire, or explode.

• Your robot is not a toy. Small children and pets should be supervised
when your robot is operating. Do not sit or stand on your robot or dock.

• Store and operate your robot in room temperature environments only.

• If the room to be cleaned contains a balcony, a physical barrier should
be used to prevent access to the balcony and ensure safe operation.

• Clean the (edge detection or cliff) sensors lens and covers on the
bottom of your robot for dust and dirt buildup as needed.

• If the room to be cleaned contains equipment, such as a stove, fan, or
humidifier, remove the equipment before operation. There is a risk of
injury, accident or malfunction if the robot comes in contact and pushes
the equipment.

• Do not use the mopping pad plate as a handle to lift or move the robot.

• Be aware that floors may be slippery after wet cleaning with your robot.

• Do not operate the robot in areas with exposed electrical outlets in the floor.

CAUTION

• Do not use this device to pick up sharp objects, glass, or anything that is
burning or smoking.

• Be aware that the robot moves on its own. Take care when walking in the
area that the robot is operating in to avoid stepping on it.

• If the device passes over a power cord and drags it, there is a chance an
object could be pulled off a table or shelf. Before using this device, pick
up objects like clothing, loose papers, pull cords for blinds or curtains,
power cords, and any fragile objects.

• Perform the required maintenance per the owner’s guide to ensure safe
operation of the robot and charging station.

• If the robot is operating on a floor with stairs, please remove any clutter
from the top step.

• Do not allow your robot or charging station to become wet.

• Do not place anything on top of your robot.

• The failure to maintain cleanliness of charger contacts could result in
loss of ability for the robot to charge the battery and the contacts to
become hot to the touch.

• Before running your robot on hard floors, please test your robot on a small
section of the hard floor to ensure that it is compatible. Using your robot
on a hard floor that is not compatible could result in damage to your floor.
Contact your hard floor manufacturer with questions on compatibility.

• Before running your robot on carpets or rugs, ensure that the carpets
or rugs are compatible with vacuums using bars or brushes. Using your
robot on a carpet or rug that is not compatible could result in damage
to your carpet or rug. Contact your carpet or rug manufacturer with
questions on compatibility.

BATTERY

WARNING

• Do not open, crush, heat above 176°F: 80°C, or incinerate. Follow the owner’s
guide instructions for proper use, maintenance, handling, and disposal.

• Do not short-circuit the battery by allowing metal objects to contact

battery terminals or immerse in liquid. Do not subject batteries to
mechanical shock.

• Lithium ion batteries and products that contain lithium ion batteries are
subject to stringent transportation regulations. If you need to ship this
product (with the battery included) for service, travel or any other reason,
you must see the Troubleshooting section of your owner’s guide or contact
customer care for shipping instructions.

• Periodically inspect the battery pack for any sign of damage or leakage.
Do not charge damaged or leaking battery packs, do not allow the liquid
to come in contact with skin or eyes. If contact has been made, wash the
affected area with copious amounts of water and seek medical advice.
Place the battery in a sealed plastic bag and recycle or dispose of safely
according to local environmental regulations, or return it to your local
authorized iRobot Service Center for disposal.

• Keep battery pack clean and dry. Wipe the cell or battery terminals with a
clean dry cloth if they become dirty.

CAUTION

• Battery usage by children should be supervised. Seek medical advice
immediately if a cell or a battery has been swallowed.

• The battery pack must be removed from the robot before recycling or
disposal.

• For best results, only use the iRobot Lithium Ion Battery that comes with
the robot.

• Do not use non-rechargeable batteries. Use only the rechargeable battery
supplied with the product. For replacement, purchase identical iRobot
battery or contact iRobot Customer Care for alternative battery options.

• Always charge and remove the battery from your robot and accessories
before long-term storage.

CLEANING SOLUTION

WARNING

• Household cleaning products are safe when used and stored according
to the instructions on the label. Always be sure to read and follow the
directions carefully.

• Only use authorized cleaning solution found on answers.irobot.com/s/
roomba-combo-cleanser.

• For cleaning solution warnings, please refer to outer box and solution
bottle

Keep away from
children

Keep away from eyes.
If product gets into
eyes rinse thoroughly
with water

Rinse hands after use

AUTOMATIC DIRT DISPOSAL

WARNING

• Do not use with damaged cord or plug. If appliance is not working as
it should, has been dropped, damaged, left outdoors, or dropped into
water, return it to a service center.

• Always disconnect your robot from the dirt disposal before cleaning or
maintaining it.

• Charge your robot only with the power supply provided. The provided
power supply delivers safety extra low voltage corresponding to the
input marking on the robot which is required to maintain safe operation.

• Do not put any object into openings. Do not use with any opening
blocked; keep free of dust, lint, hair, and anything that may reduce air
flow.

• To prevent the risk of your robot falling downstairs, ensure that the
charging station is placed at least 4 feet (1.2 meters) away from stairs.

• To properly maintain your dirt disposal, do not place foreign objects in
your Automatic Dirt Disposal Port and ensure it is clear of debris.

• In order to avoid a hazard due to inadvertent resetting of the thermal
cut-out, this appliance must not be supplied through an external
switching device, such as a timer, or connected to a circuit that is
regularly switched on and off by the utility.

• Do not pour any liquids into the device and do not immerse in water.

• Do not allow liquids to get on or into the dirt disposal.

• Do not use outdoors or on wet surfaces.

EN

EN

• Do not allow to be used as a toy. Close attention is necessary when used
by or near children.

• In order to avoid a hazard due to inadvertent resetting of the thermal
cut-out, this appliance must not be supplied through an external
switching device, such as a timer, or connected to a circuit that is
regularly switched on and off by the utility.

• Use only as described in this manual.

• To reduce the risk of electric shock, unplug your dirt disposal before
cleaning.

• Keep the dirt disposal and power cord away from heated surfaces.

CAUTION

• Only charge the battery that came with your robot. Other types of
batteries may burst causing injury. Always contact iRobot Customer
Care for the correct replacement of your battery.

• Product may not be used with any type of power converter. Use of power
converters will immediately void the warranty.

• If you live in an area prone to electrical storms, it is recommended that
you use additional surge protection. Your dirt disposal may be protected
with a surge protector in the event of severe electrical storms.

• Do not use without dust bag and/or filters in place.or rugs are
compatible with vacuums using bars or brushes. Using your robot on
a carpet or rug that is not compatible could result in damage to your
carpet or rug. Contact your carpet or rug manufacturer with questions
on compatibility.

This symbol on the battery indicates that the battery must not be disposed
of with unsorted common municipal waste. As the end-user, it is your
responsibility to dispose of the end-of-life battery in your appliance in an
environmentally sensitive manner as follows:

(1) Returning it to the distributor/dealer from whom you purchased the
product or

(2) Depositing it at a designated collection point

The separate collection and recycling of end-of-life batteries at the time
of disposal will help to conserve natural resources and to ensure that it is
recycled in a manner that protects human health and the environment.
For more information, please contact your local recycling office or the
dealer from whom you originally purchased the product. Failure to properly
dispose of end-of-life batteries may result in negative potential effects on
the environment and human health due to the substances in the batteries
and accumulators.

For battery recycling go to call2recycle.org or call 1-800-822-8837

About your Roomba Combo™ Robot Vacuum & Mop

BinTop View

Mopping Pad Plate

Wall Follow Sensor

Faceplate

Clean Button

Camera

Dust Bin

Filter

Tank Cap

Water Tank

EN

Bottom View

Multi-Surface
Brushes

Cliff Sensors

Charging
Contacts

Edge-Sweeping
Brush

Cliff Sensor

Floor Sensor

Bin Release
Button

Brush Caps

Caster Wheel

Floor Tracking
Sensor

Cliff Sensor

Brush Frame
Release Tab

Floor Sensors

Cliff Sensors

Bin

Roomba Combo j7+ Owner’s Guide 1

About Your Clean Base™ Automatic Dirt Disposal

EN

Front View

Canister Lid

Exhaust Vent

Charging
Contacts

Wheel Wells

Top View

Bag Storage
Compartment

Blow Cover

Pull Tab

LED Indicator

Visual Docking
Target

Debris Evacuation
Port

Bag Guide Rails

Debris Evacuation
Tube

Bag Presence Sensor

Back View

Bottom View

Cord Wrap

Debris Evacuation
Tube

2 For more information, visit global.irobot.com

Using Your Roomba Combo™ Robot Vacuum & Mop

Positioning the Clean Base™ Automatic Dirt Disposal

Good Wi-Fi® Coverage

1ft (0.3 m)
above

Note: Do not place

your Clean Base™
in direct sunlight.
Ensure the area
around the dock

1.5 ft (0.5 m)
both sides

4 ft (1.2 m)
from stairs

4 ft (1.2 m)
in front

*Objects are not to scale.

is free of clutter to
improve docking
performance.

WARNING: To
prevent the risk of
your robot falling
downstairs, ensure
that the charging
station is placed
at least 4 feet (1.2
meters) away from
stairs.

Download the iRobot Home App and Connect to Wi-Fi®

• Follow step-by-step instructions to set up your Roomba Combo™.

• Set up PrecisionVision Navigation to avoid obstacles in real time.

• Set an automatic cleaning schedule and customize cleaning preferences.

• Create smart maps to tell your robot where, when and how to clean.

Charging

Light Ring Spiral While Charging

White Spiral: charging

CLEAN

• Place the robot on the charging station to activate the battery.

Note: Your robot comes with a partial charge, but we recommend that you charge

the robot for 3 hours prior to starting the first cleaning job.

• The robot uses a small amount of power whenever it is on the charging
station. You can put the robot in a further-reduced power state when not in
use. For instructions and more details on this Reduced Power Standby Mode,
refer to the FAQ page on our website.

• For long-term storage, turn off the robot by removing it from the charging
station and holding down the clean button for 3 seconds with one wheel off
the ground. Store the robot in a cool, dry place.

A solid white light will indicate the battery
charge percentage of your robot

When your robot is fully charged, the
light ring indicator will intermittently
pulse white at the rear.

EN

Roomba Combo j7+ Owner’s Guide 3

Cleaning

EN

Just press the clean button

Tap to Start / Pause / Resume
Hold for 2-5 seconds to end a job

• Your robot will automatically explore and clean your home in neat rows,
avoiding obstacles using its front-facing camera. It will return to the charging
station at the end of a cleaning job and whenever it needs to recharge.

Your robot is able to recognize and avoid
objects. However, it is still recommended
to remove excess clutter before cleaning.

• To end a job and send the robot back to its charging station, hold the clean
button down for between 2-5 seconds. A blue light ring pattern will indicate
that the robot is seeking the charging station.

• When your robot detects an especially dirty area, it will engage Dirt Detect™
mode, moving in a forward/backward motion to clean the area more
thoroughly. The light ring indicator will flash blue.

When your robot senses that its bin needs
to be emptied, the light ring indicator
will illuminate in a red sweeping motion
toward the rear.

Vacuuming

• To start a vacuum-only cleaning job from your robot, empty the tank or
detach the mopping pad before pressing the clean button.

Mopping

• Your robot is able both vacuum and mop at the same time. To start a
vacuum and mop cleaning job from your robot, fill the tank, attach a
mopping pad, and press the clean button.

• When your robot encounters carpet during it’s
cleaning job, it will lift and tuck the mopping
pad away.

• After completing your mopping and vacuum
cleaning job, make sure to empty the water
tank and replace the mopping pad.

WARNING: To prevent damaging your robot, do not manually stow the
mopping pad plate onto the pad shelf.

Press bin release button to

1

remove bin.

Attach mopping pad.

3

Fill tank with water and

2

compatible cleaning solution.

Place bin back in the robot.

4

4 For more information, visit global.irobot.com

Cleaning Solution

For best results when mopping, use Bona® Hardwood or Hard-Surface Floor
Cleaning Solutions. Both solutions are suitable for most well-sealed hard floors.

Sample Concentrate Packets

Included in box

1 Packet per tank
Mix to manufacture instruction
and pour into tank.

Retail Ready-to-Use Bottles

Sold separately

Fill the tank with cleaning solution. No
water is necessary.

Important: Only certain cleaning solutions can be safely used with your

robot. A full list of compatible cleaning solutions can be found on answers.
irobot.com/s/roomba-combo-cleanser or by visiting the app. Please do
not use other cleaning solutions or bleach-based products.

About Your Automatic Dirt Disposal

While cleaning, your robot will automatically return to the dirt disposal to empty
its bin and recharge as needed.

The dirt disposal’s LED indicator will turn solid red when a new bag is needed.
If a clog is detected, the dirt disposal will trigger additional attempts to
automatically clear the clog.

Note: If you place your robot on the dirt disposal by hand, it will not empty automatically.

In this case, use the iRobot Home App or hold the button down for 2-5 seconds.

Troubleshooting

• Your robot will tell you
something is wrong by playing
an audio alert and turning the
light ring indicator red. Press the
clean button or tap the bumper
for details. Check the iRobot
Home App for further support.

• After 90 minutes of inactivity
off the charging station, the
robot will automatically end its
cleaning job.

• To factory reset your robot, remove the dust bin and hold the clean button
down for seven (7) seconds. A sound will let you know when the factory reset
has been completed. Press the clean button down once more to confirm.

Battery Safety & Shipping

For best results, only use the iRobot Lithium Ion Battery that comes with your robot.

WARNING: Lithium ion batteries and products that contain lithium ion
batteries are subject to stringent transportation regulations. If you need to
ship this product for service, travel or any other reason, you MUST follow the
below shipping instructions.

• Battery MUST be turned off before shipping.

• Turn off the battery by removing the robot from the charging station
and holding down the clean button for 3 seconds with one wheel off the
ground. All indicators will turn off.

• Package the robot securely for shipping.

• If you need further assistance, contact our Customer Care team or visit
global.irobot.com.

Red Light Ring

Low battery. Please charge.

EN

Roomba Combo j7+ Owner’s Guide 5

Care and Maintenance

EN

Troubleshooting Your Automatic Dirt Disposal

Your dirt disposal will tell you if something is wrong via an LED indicator on the
front of the canister and through the iRobot Home app.

LED Indicator Common Error How to Fix

Solid Red Bag full or missing 1. Replace bag if it is full or missing.

Blinking Red There is a leak or

a clog in the dock
evacuation path

This product has been equipped with a thermal protector designed to protect

against damage due to overheating. If the protector operates, themotor will stop
running. If this happens, unplug the unit, allow to cool for30 minutes, clear any

obstructions from the evacuation port and evacuation tube, and plug the unit
back in.

2. Make sure the bag is securely inserted.

3. If problem persists, remove any debris
from the port on the bottom of your robot
and the dirt disposal.

1. Make sure the canister lid is pushed down
and firmly sealed. Hold the clean button
on your robot down for 2 seconds to
manually empty the bin.

2. Remove any debris from the port on the
bottom of your robot and dirt disposal.

3. Unplug the dirt disposal from the wall.
Place it on its side and inspect the debris
evacuation tube for debris. If necessary,
remove the tube to clear any debris.

Care and Maintenance Instructions

To keep your robot running at peak performance, perform the procedures on the
following pages.

There are additional instructional videos in the iRobot Home App. If you notice
the robot picking up less debris from your floor, empty the bin, clean the filter and
clean the brushes.

Part Care Frequency Replacement Frequency*

Mopping Pad Clean after a mopping job After 30 washes.

Bin Wash bin as needed

Filter Clean once a week (twice a

Charging Contacts Clean every 2 weeks

Full Bin Sensor Clean every 2 weeks

Front Caster Wheel Clean every 2 weeks Every 12 months

Edge-Sweeping Brush and
Multi-Surface Brushes

Sensor, Camera Window
and Pad Shelf

Bags - Bags should be replaced

Blower Cover inside
canister

Note: iRobot manufactures various replacement parts and assemblies. If you think you

need a replacement part, please contact iRobot Customer Care for more information.

* Replacement frequency may vary. Parts should be replaced if visible wear appears.

week if you have a pet). Do
not wash.

Clean once a month (twice a
month if you have a pet)

Clean once a month

Once every month (remove
debris from blower cover)

Every 2 months

Every 12 months

when prompted by the LED
indicator / app

6 For more information, visit global.irobot.com

Cleaning the Mopping Pad Emptying the Bin

Note: You can clean your mopping pads two ways:

either by hand washing, or in a washing machine.

HAND WASHING

Thoroughly wash the pad with warm water.

MACHINE WASHING

Wash using the warm cycle, then air dry. Do not
put in dryer. Do not wash with delicates.

Press bin release button to remove bin.

1

Open bin door to empty bin.

2

Place bin back in the robot.

3

Cleaning the Filter

Remove the bin. Remove the filter by

1

grasping both ends and pulling out.

Remove debris by tapping the filter

2

against your trash container.

Reinsert filter with ridged grips facing out.

3

Place bin back in the robot.

Important: The robot will not run if the

filter is not installed correctly. Replace
the filter every two months.

EN

Roomba Combo j7+ Owner’s Guide 7

EN

Cleaning the Charging
Contacts

Wipe the charging contacts with a
clean, dry cloth.

1

Cleaning the Full Bin Sensors

Remove and empty the bin.

1

Wipe the bin door with a clean, dry cloth. Clear any debris from the

3 4

Closed Door

Opened Door

Wipe the inner sensors with a clean,
dry cloth

2

vacuum path.

8 For more information, visit global.irobot.com

Cleaning the Multi-Surface Brushes Cleaning the Front Caster Wheel

Pinch the brush frame release tab, lift the

1 1

tab, and remove any obstructions.

Remove the brushes from the robot.

2

Remove the brush caps from the ends of
the brushes. Remove any hair or debris
that has collected beneath the caps.
Reinstall the brush caps.

2
3
4

Remove any hair or debris from the square

3

and hexagonal pegs on the opposite side
of the brushes.

Reinstall the brushes in the robot. Match

4

the shape of the brush pegs with the
shape of the brush icons in the cleaning
head module.

Pull firmly on the front wheel module to
remove it from the robot.

Pull firmly on the wheel to remove it from its
housing (see illustration below).

Remove any debris from inside the
wheel cavity.

Reinstall all parts when finished.
Make sure the wheel clicks back into place.

Wheel

Axle

Housing

Important: A front wheel clogged with

hair and debris could result in damage to
your floor. If the wheel is not spinning freely
after you have cleaned it, please contact
Customer Care.

EN

Roomba Combo j7+ Owner’s Guide 9

EN

Cleaning the Filter Cleaning the Edge-Sweeping

Important: Do not wash the filter.

Remove the filter before washing the bin.

Release the bin, remove the filter, and

1

open the bin door.

Rinse the dust bin and water tank using
warm water.

2

Note: Bin is not dishwasher safe.

Make sure bin is completely dry. Reinsert
filter and place bin back in the robot.

3

Brush

Use a coin or small screwdriver to remove

1

the screw holding the Edge-Sweeping
Brush in place.

Pull to remove the Edge-Sweeping Brush.

2

Remove any hair or debris, then reinstall
the brush.

Cleaning the Sensors, Camera
Window and Charging Contacts

Wipe sensors, camera window and pad

1

shelf with a clean, dry cloth.

Note: You can clean your mopping pads

two ways: either by hand washing, or in a
washing machine.

10 For more information, visit global.irobot.com

Important: Do not spray cleaning solution or

water onto the sensors or sensor openings.

Replacing the Bag Removing Debris from Blower Cover

Lift up on the canister lid to open. Pull up on the plastic card to remove the

1 3

Discard the used bag.

2

Note: This will seal

the bag so dust
and debris cannot
escape.

bag from the canister.

Install a new bag, sliding the

4

plastic card into the guide rails.

Press down on the lid making sure it is

5

completely closed.

Note: To achieve optimal performance with

your robot and automatic dirt disposal,
clean and/or replace your robot’s filter as
needed.

Inspect blower cover for any lint or debris built-up
and wipe with a clean dry cloth to remove.

EN

Roomba Combo j7+ Owner’s Guide 11

iRobot Customer Care

EN

USA & Canada

If you have questions or comments about your dirt disposal, please contact
iRobot before contacting a retailer.

You can start by visiting global.irobot.com for support tips, frequently asked
questions, and information about accessories. This information can also be
found in the iRobot HOME App. If you need further assistance, call the US
Customer Care team at [phone].

iRobot USA Customer Care Hours

Monday to Friday, 9AM — 9PM Eastern Time
Saturday and Sunday 9AM — 6PM Eastern Time

Outside USA & Canada

Visit global.irobot.com to:
Learn more about iRobot in your country
Get hints and tips to improve your product performance
Get answers to questions
Contact your local support center

12 For more information, visit global.irobot.com

Regulatory Information

iRobot Corporation Roomba Model: RCA-Y1

FCC ID: UFE-RCAY1
Contains FCC ID: UFE-AXGY1 and contains IC: 6652A-AXGY1

This device complies with part 15 of the FCC Rules and ICES-003.

Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: 1) This device may not
cause interference, and 2) this device must accept any interference, including
interference that may cause undesired operation of the device.

• Changes or modifications not expressly approved by iRobot Corporation
could void the user’s authority to operate the equipment.

• This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules as well as ICES­003 Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference to radio
communication will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Supplier’s Declaration of Conformity

• Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for
the transmitter by Industry Canada. To reduce potential radio interference
to other users, the antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.) is not more than the
necessary for successful communication.

• FCC Radiation Exposure Statement: This product complies with FCC

§2.1091(b) for mobile device RF exposure limits, set forth for an uncontrolled
environment and is safe for the intended operation as described in this
manual. Per FCC requirements, maintain a distance of more than 8 inches
(20 cm) between any person and the host device (Roomba Combo robot).

• ISED Radiation Exposure Statement: This product complies with the Canadian
Standard RSS-102 for mobile device RF exposure limits, set forth for an
uncontrolled environment and is safe for the intended operation as described
in this manual. Per ISED requirements,
maintain a distance of more than 8 inches (20 cm) between any person and
the robot.

iRobot Corporation, 8 Crosby Drive, Bedford, MA 01730 USA.
https://global.irobot.com

For battery recycling go to call2recycle.org;
or call 1-800-822-8837

EN

Roomba Combo j7+ Owner’s Guide 13