Invacare T1483 User Manual

Push Bar

Assembly, Installation and Operating Instructions

Model No. T1483

SAVE THESE INSTRUCTIONS

NOTE: Check all parts for shipping damage before using.
In case of damage, DO NOT use the equipment. Contact

the Dealer/Carrier for further instructions.

SAFETY SUMMARY

The following recommendations are made for the safe
use of the Push Bar:

GENERAL WARNING

DO NOT install or use this equipment without
first reading and understanding these
instructions. If you are unable to understand the
Warnings, Cautions or Instructions, contact a
healthcare professional, dealer or technical per­sonnel before attempting to install this equipment

- otherwise, injury or damage may occur.

INSTALLATION WARNING

After ANY adjustments, repair or service and BE­FORE use, make sure that all attaching hardware
is tightened securely.

This kit includes the following:

CAUTION

The Mounting screws MUST be securely tightened
into the threaded mounting holes of the wheel­chair frame before installing the locknuts - other­wise, damamage may occur.

3. Insert the (2) NEW back canes into the wheelchair
frame and secure with the four (4) long mounting
screws through the threaded mounting holes of the
wheelchair frame and the back cane. Securely tighten.

4. Reinstall the four (4) locknuts. Securely tighten.

5. Securely tighten the back upholstery to the NEW back
canes with the eighteen (18) mounting screws and
washers starting with the top hole of the back cane.

Washers

Mounting

Screws

Back Cane Handles

Back

Canes

Locknuts

ITEM QUANTITY

Push Bar (With Lock Knobs) 1
Back Canes 2

INSTALLING THE BACK CANES
(FIGURE 1)

NOTE: Refer to the GENERAL WARNINGS in the
SAFETY SUMMARY of this Instruction Sheet.

NOTE: Take note of the position and orientation of the
back cane mounting hardware. The NEW back canes
will be installed at the same height settings as the EXIST­ING back canes.

1. Remove the eighteen (18) mounting screws and wash­ers that secure the EXISTING back upholstery to the
back canes. Set aside the mounting screws, washers
and back upholstery.

2. Remove the four (4) long mounting screws and lock­nuts that secure the two (2) EXISTING back canes to
the wheelchair frame.

Back

Upholstery

Wheelchair

Frame

Long Mounting

Screws

FIGURE 1 - INSTALLING THE BACK CANES

INSTALLING/REMOVING THE PUSH
BAR (FIGURE 2)

NOTE: The 9000 Topaz is folded for either storage or
transporting. The push bar must be removed before fold­ing the wheelchair.

Installing The Push Bar

1. Insert one (1) bush bar support into one (1) back cane
handle.

Push Bar Support

Back Cane Handle

Lock Knob

Push Bar

Support

Push Bar

NOTE It may be necessary to move the back cane
side-to-side in order to align the remaining pushbar
support with the back cane handle.

2. Align the remaining pushbar support with the remain­ing back cane handle.

3. Insert the push bar support into the back cane handle.
Securely tighten both lock knobs.

Removing The Push Bar

1. Completely unthread both lock knobs.

2. Firmly grasp both ends of the push bar and PULL to
remove the push bar from the back cane handles.

Lock Knob

FIGURE 2 - INSTALLING/REMOVING THE PUSH

BAR

Invacare Corporation www.invacare.com

USA Canada

One Invacare Way 5970 Chedworth Way Invacare® and Yes, you can. are trademarks of Invacare
Elyria, Ohio USA Mississauga, Ontario Corporation.
44036-2125 L5R 3T9, Canada © 2000 Invacare Corporation
800-333-6900 905-890-8838 Form No. 00-183 Part No. 1100904 Rev B (1) 2/01