Interlogix TruVision 11 Series, TruVision 31 Series, TruVision 13 Series Installation Manual

TruVision

11/31

Series

Wi-Fi IP

Camera Installation
Guide

P/N 1072907-EN • REV B • ISS 24APR15

Copyright

© 2015 United Technologies Corporation,
Interlogix is part of UTC Building & Industrial Systems, a unit of United

Technologies Corporation. All rights reserved.

Trademarks and patents

Trade names used in this document may be trademarks or registered trademarks
of the manufacturers or vendors of the respective products.

Manufacturer

Interogix
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA

Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands

Certification

N4131

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.

4. Consult the dealer or an experienced radio technician for help.

CC Caution

To assure continued compliance, use only shielded interface cables when
connecting to computer or peripheral devices. Any changes or modifications not
expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:

(1) This device may not cause harmful interference

(2) This Device must accept any interference received, including interference that

may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an

uncontrolled environment. In order to avoid the possibility of exceeding the FCC
radio frequency exposure limits, human proximity to the antenna shall not be less
than 20 cm (8 inches) during normal operation.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF
THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio
equipment and telecommunication terminal Equipment and the mutual
recognition of their conformity (R&TTE). The R&TTE Directive repeals and
replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment
and Satellite Earth Station Equipment) as of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those who
install and use it. However, special attention must be paid to the dangers of
electric shock and static electricity when working with electrical equipment. All
guidelines of this and of the computer manufacture must therefore be allowed at
all times to ensure the safe use of the equipment.

National Restrictions

This device is intended for home and office use in all EU countries (and other
countries following the EU directive 1999/5/EC) without any limitation except for
the countries mentioned below:

Country Restriction Reasons/remarks

Bulgaria

None

General authorization required for

outdoor use and public service

France

Outdoor use;

limited to 10 mW
e.i.r.p. within the
band 2454-

2483.5 MHz.

Military Radiolocation use. Refarming

of the 2.4 GHz band has been ongoing
in recent years to allow current relaxed
regulation. Full implementation
planned 2012

Luxembourg

None

General authorization required for

network and service supply(not for
spectrum).

Annex 3 B and A Wideband Data Transmission systems 2400.0-2483.5 MHz:

Country Restriction Reasons/remarks

Norway

Implemented

This subsection does not apply for the

geographical area within a radius of
20 km from the centre of Ny-Ålesund.

Italy

Implemented

The public use is subject to general

authorization by the respective service
provider.

Russian

Federation

Limited

implementation

1. SRD with FHSS modulation

1.1. Maximum 2.5 mW e.i.r.p.

1.2. Maximum 100 mW e.i.r.p.
Permitted for use SRD for outdoor
applications without restriction on
installation height only for purposes of
gathering telemetry information for
automated monitoring and resources
accounting systems. Permitted to use
SRD for other purposes for outdoor
applications only when the installation
height is not exceeding 10 m above
the ground surface. 1.3 maximum
100 mW e.i.r.p. indoor applications.

2. SRD with DSSS and other than
FHSS wideband modulation

2.1. Maximum mean e.i.r.p. density is
2 mW/MHz. Maximum 100 mW e.i.r.p.

2.2. Maximum mean e.i.r.p. density is
20 mW/MHz. Maximum 100 mW
e.i.r.p. It is permitted to use SRD for
outdoor applications only for purposes
of gathering telemetry information for
automated monitoring and resources
accounting systems or security
systems.

2.3. Maximum mean e.i.r.p. density is
10 mW/MHz. Maximum 100 mW
e.i.r.p. indoor applications.

Ukraine

Limited

implementation

e.i.r.p. ≤100 mW with built-in antenna

with amplification factor up to 6 dBi.

The following information shall also be included in the case of radio equipment

intentionally emitting radio waves:

(a) frequency band(s) in which the radio equipment operates;
(b) maximum radio-frequency power transmitted in the frequency band(s) in

which the radio equipment operates.

2012/19/EU (WEEE directive): Products marked with this

symbol cannot be disposed of as unsorted municipal waste
in the European Union. For proper recycling, return this
product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info.

2006/66/EC (battery directive): This product contains a

battery that cannot be disposed of as unsorted municipal
waste in the European Union. See the product
documentation for specific battery information. The battery
is marked with this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg). For
proper recycling, return the battery to your supplier or to a
designated collection point. For more information see:
www.recyclethis.info.

Contact

information

For contact information, see www.interlogix.com or

www.utcfssecurityproducts.eu.

6 Installation Guide

Content

Introduction 7

Product overview 7

Installation 7

Installation environment 7
Package contents 8
Cable requirements 11
Camera description 11
Setting up the camera 12
Setting up Wi-Fi transmission 12
Accessing the SD card 19
Connecting a speaker 20
Mounting the wedge camera 21
Using the camera with a recorder 23
Using the camera with TruVision Navigator 24
Ensuring corrosion resistance 24

Specifications 25

TruVision IP wedge cameras 25

Pin definitions 26

Installation Guide 7

Introduction

Product overview

This is the installation guide for TruVision 11-31 Series Wi-Fi IP
camera models:

 TVW-1103 (1.3MPX Wi-Fi, 2.8mm lens, Grey, PAL)

 TVW-3103 (1.3MPX Wi-Fi, 2.8mm lens, Grey, NTSC)

 TVW-1104 (1.3MPX Wi-Fi, 2.8mm lens, White, PAL)

 TVW-3104 (1.3MPX Wi-Fi, 2.8mm lens, White, NTSC)

 TVW-1105 (3MPX Wi-Fi, 2.8mm lens, Grey, PAL)

 TVW-3105 (3MPX Wi-Fi, 2.8mm lens, Grey, NTSC)

 TVW-1106 (3MPX Wi-Fi, 2.8mm lens, White, PAL)

 TVW-3106 (3MPX Wi-Fi, 2.8mm lens, White, NTSC)

 TVW-1116 (3MPX Wi-Fi, 6mm lens, White, PAL)

 TVW-3116 (3MPX Wi-Fi, 6mm lens, White, NTSC)

Installation

This section provides information on how to install the cameras.

Installation environment

When installing your product, consider these factors:

• Electrical: Install electrical wiring carefully. It should be
done by qualified service personnel. Always use a proper
PoE switch or a 12 VDC UL listed Class 2 or CE certified

8 Installation Guide

power supply to power the camera. Do not overload the
power cord or adapter.

• Ventilation: Ensure that the location planned for the
installation of the camera is well ventilated.

• Temperature: Do not operate the camera beyond the
specified temperature, humidity or power source ratings.
The operating temperature of the camera is between -30
to +60°C (-22 to 140°F). Humidity is below 90%.

• Moisture: Do not expose the camera to rain or moisture,
or try to operate it in wet areas. Turn the power off
immediately if the camera is wet and ask a qualified
service person for servicing. Moisture can damage the
camera and also create the danger of electric shock.

• Servicing: Do not attempt to service this camera yourself.
Any attempt to dismantle or remove the covers from this
product will invalidate the warranty and may also result in
serious injury. Refer all servicing to qualified service
personnel.

• Cleaning: Do not touch the sensor modules with fingers. If
cleaning is necessary, use a clean cloth with some ethanol
and wipe the camera gently. If the camera will not be used
for an extended period of time, put on the lens cap to
protect the sensors from dirt.

Package contents

Check the package and contents for visible damage. If any
components are damaged or missing, do not attempt to use the
unit; contact the supplier immediately. If the unit is returned, it
must be shipped back in its original packaging.

Installation Guide 9

IP wedge camera

Camera

Installation manual

CD with Configuration
Manual and TruVision Device
Finder

Template A for mounting
with the converter pan

Template B for mounting
without the converter pan

Screws

Drywall anchor

Φ7.5 x 24.5mm (3 pcs)

Screw M4

(4 x 25mm (3 pcs)