Interlogix 60-886-11-95, 60-886-95 Installation
/HDUQ0RGH6KRFN
6HQVRU
ITI Part No. 60-886-95
60-886-11-95
Document Number: 466-1925 Rev. A
December 2001
Product Summary
The Learn Mode Shock Sensor has the followin g three main
functions:
❑ To detect the vibrations made by an intruder trying to
break a wind ow or door.
❑ To detect a window or door opening.
❑ To detect tamper situations, such as an intruder remov-
ing the sensor cover.
Vibrations cause a momentary open circuit in the shock element of the sensor. The circuit closes again when the vibration stops. The sensor microcontroller “sees” the o pen/close
action as a pulse, causing the sensor to transmit an alarm
signal. The sensor has two different detection modes:
❑ Gross Attack - detect a violent blow sufficient in length
to trip sensor.
❑ Pulse Count - detect a sufficient number of less violent
blows (rapping or tapping).
The sensor includes an internal magnetic reed switch that
must be disabled if it is not used.
A cover tamper provides additional security if an intruder
tries to disable or damage the sensor.
Shock
Element
LOGO
8 3 9 4 g 0 9 b . d s f
Installation Instructions
receive sensor signal transmissions. The sensor is an
RF device and there may be blind or non-operational
locations within the installation. Normally, these can be
overcome by moving the sensor or receiver.
❑ Always mount the shock sensor so that the detector is
on the frame and not on glass, solid, or hollow-core
doors. See Figure 2 for mounting locations.
9HUWLFDO6XUIDFH0RXQWLQJ
Shock Sensor Shock Sensor
+RUL]RQWDO)ODW6XUIDFH0RXQWLQJ
Shock Sensor
Figure 2. Mounting Options for Door/Window Styles
Shock Sensor
8 3 9 4 g 1 0 b . d s f
DIP
Switches
Battery
Holder
Figure 1. Shock Sensor Main Components
O N
1 2 3 4 5 6
Reed
Switch
Cover
Tamper
Switch
Installation Guidelines
❑ Learn the sensor before adjusting the shock sensitivity.
The sensor is shipped with the reed switch enabled and
open, and this is how it must be learned.
❑ Before permanently mounting the sensor, test it at the
intended location to make sure that the panel can
❑ Mount the sensor in a location where the structure can
transmit vibrations to the sensor.
❑ The sensor can be mounted on a vertical surface or on a
horizontal (flat) surface.
❑ Make sure the window fits snugly in the frame and
doesn’t move or rattle.
❑ Hold the sensor against the frame to make sure the sen-
sor base fits on the surface area of the frame and
doesn’t extend over the surface edges.
Shock Sensor Orientation
There are two types of shock sensor mounting orientations;
on a vertical surface or on a horizontal surface (sill or
ledge).
On a vertical surface, there are two orientations (see Figure
3).
Note
On a vertical surface, the shock sensor element must
always be oriented with its screw terminals down
writing on the shock elem ent horizontal.
, or the
1
Installation
1 2 3 4 5 6
O N
1 2 3 4 5 6
O N
Shock
Element
Shock
Element
Screw
Terminals
Screw
Terminals
LOGO
LOGO
1 2 3 4 5 6
O N
1 2 3 4 5 6
O N
Shock
Element
Shock
Element
Screw T e rm i n al s
Screw
Terminals
Parallel
Perpendicular
(Bad)
(Good)
LOGO
LOGO
Direction of
Vibration
Figure 3. Positioning shock element according to
mounting orientation on a vertical surface
On a horizontal surface (sill or ledge), any orientation is
allowed, but certain sensor element orientations are better
than others. The element is much better at detecting horizontal vibrations perpendicular to its writing than parallel
(see Figure 4).
Top
End
Slot
8 3 9 4 g 0 2 b . d s f
Figure 5. Remove the sensor cover
2. Using the flathead mounting screws, secure the base to
the mounting surface either vertically or horizontally as
required (see Figure 6).
Mounting
Hole
(Located
Under Shock
Element)
Shock
Element
LOGO
O N
1 2 3 4 5 6
Figure 4. Positioning shock elements for horizontal
surface mounting
Tools and Supplies
❑ Control panel installat ion in st ru ct ions
❑ Phillips screwdriver
❑ Slotted screwdriver (to pry off the cover)
❑ Two #6 x 3/4” flat head sc rews for mou nti ng the s ens or
(included)
❑ Two #6 x 5/8” screws for mounting the magnet
(included)
Installation
Caution!
You must be free of all static elec t rici t y w he n handling
electronic component s. Touch a grounded, bare metal
surface before touching a circuit board or wear a grounded
wrist strap.
1. Insert a slotted screwdriver into the slot at the top end of
the unit and remove the cover (see Figure 5).
2
Mounting
Hole
Figure 6. Sensor base mounting holes
3. Position the shock element and press it firmly into its
socket (see Figure 7).
4. If using the reed switch, use the two remaining screws
to mount the magnet so that its arrow is aligned with the
arrow on the sensor case (see Figure 7).
Arrows
Magnet
Figure 7. Magnet alignment
Important! You must disable the reed switch if you
are not using it. If the reed switch is enabled but no
magnet is installed, the sensor will be in a continuous
alarm state.
Loading...