Interlogix 60-770 User Manual
ITI Part No. 60-770
SuperBus
®
2000
4-Relay Output Module
Document Number: 466-1608 Re v. B
November 2000
Product Summary
Each SuperBus 2000 4-Relay Output module adds four programmable relay outputs to a compatible panel.
Examples of module uses include:
❑ Turning on a CCTV camera during a burglary alarm.
❑ Turning on exit lights during a fire alarm.
❑ Activating backup cellular phones or long-range radios
if primary communications are inoperable.
Each module comes complete with mounting hardware.
Power for the module is provided by the panel.
®
Advent
programmed) output points.
UltraGard
of 32 output points.
For additional security, the plastic case accommodates a
magnetic reed switch to provide tamper protection . Simply
connect a UL listed reed switch to the module built-in zone
input or to one of the fire/security panel hardwire input
zones.
SuperBus 2000 vs. SuperBus
panels can be expanded to a total of 124 (24 pre-
®
and Concord™ panels can be expanded to a total
8557109A.DS4
Installation Instructions
Module Components
Figure 1 shows the main module components and Table 1
describes them.
UNIT NUMBER
DIP SWITCHES
BUS STATUS LED
(RED)
POWER LED
(GREEN)
OUTPUT RELAYS (4)
SOFTWARE
VERSION LABEL
SUPERBUS 2000
DEVICE ID
NUMBER LABEL
WIRING
TERMINALS
9710G01A.DSF
Figure 1. Module Circuit Board Components
SuperBus 2000 panels have the ability to auto-address module unit numbers. When the panel is initially powered up,
the panel automatically reads the unique SuperBus 2000
device ID number and assigns a unit number to the module.
This eliminates manually setting DIP switches and the
chance of identical unit number conflicts.
SuperBus 2000 Panels
❑ Advent
❑ Concord (software versions 2.0 and later)
SuperBus panels communicate with SuperBus 2000 modules but require the mod ule unit number to first be set manually with DIP switches.
SuperBus Panels
❑ UltraGard
❑ Concord (software versions 1.0–1.6)
SuperBus® 2000 4-Relay Output Module
Table 1: Module Component Descriptions
Component Function
Unit Number DIP
Switches
BUS LED (Red) Flashes to indicate normal
POWER LED
(Green)
Output Relays Form C (dry contact) output relays rated
SuperBus 2000
Device ID Number
Label
Software Version
Label
Wiring Terminals Used for power, bus, and output wiring
Used for manually setting module unit
number (SuperBus panels).
communication with the panel.
Indicates module power status.
4A @ 24VDC, 4A @ 24VAC, 1A @
70VAC maximum.
Identifies the unique device ID
(SuperBus 2000).
Identifies the installed software version.
connections. All terminals are Class 2
power limited.
1
Installation Guidelines
PRESS DOWN
HERE AND PULL
AWAY FROM BASE
8557G47B.DS4
Installation Guidelines
❑ For the maximum number of bus devices and
touchpads per panel see Table 2.
Table 2: Maximum Bus Devices Per Panel
Panel Maximum Bus
Devices
Advent 62
UltraGard 8
Concord
(software versions 2.0 and later)
Concord
(software versions 1.0–1.6)
(up to eight 4-Relay
❑ Do not exceed the panel total DC output power rating
when using panel power for bus devices and hardwired
detectors (see specific panel Installation Instructions).
❑ Do not exceed the maximum wire length from the
panel to the module (see Table 3).
Table 3: Maximum Wire Lengths
Panel Maximum Wire Length
Advent
UltraGard 22 ga. 500 ft./18 ga. 1000 ft.
22 ga. 200 ft./18 ga. 500 ft.
16
16
Output modules)
Installation
The relay output module can be mounted:
❑ On a wall.
❑ Inside an Advent cabinet.
❑ Inside a Concord cabinet.
❑ Inside a SuperBus Module cabinet (60-698). Refer to
the cabinet Installation Instructions for installation
procedures.
CAUTION
To prevent damaging the panel or card, disconnect the
panel AC Power and backup battery(s) before
installation.
CAUTION
You must be free of all static electricity when handling
electronic components. Touch a bare metal surface
before touching the circuit board.
Mounting the Module
Note
If connecting th e modu le to an UltraGar d panel it must
be mounted on a wall. The module will not fit in the
UltraGard cabinet.
Mounting the Module on a Wall
Concord
22 ga. 350 ft./18 ga. 900 ft.
❑ When using self or remotely powered devices with an
Advent panel, do not exceed the maximum recommended wire length of 4000 feet using 22-gauge or
larger wire.
❑ Maximum module current draw with all output s ener-
gized is 180 mA. Each module draws 12 mA typical
when outputs are not energized (idle).
❑ Do not exceed the module output relay contact ratings
(
4A @ 24VDC, 4A @ 24VAC, 1A @ 70VAC maximum).
Tools and Supplies Needed
❑ Screwdrivers
❑ Drill with bits
❑ Wire cutters/strippers
❑ 3/8-inch #6-32 self-tapping screws (included)
❑ 22-gauge or larger stranded wire (18-gauge or larger
for commercial applications)
❑ 1/4-inch press-fit reed switch and magnet (not
included) for cover tamper
❑ 1/4-inch #6-32 self tapping screws (not included) for
Advent cabinet mounting
❑ Support standoff (included with Concord cabinet)
1. Remove the module cover and set it aside (Figure 2).
Figure 2. Removing the Cover
2. Place the back-plate on the wall and mark the mounting holes (Figure 3).
3. Drill holes and insert appropriate anchors.
4. Secure the back-plate to the wall with included screws.
2
SuperBus® 2000 4-Relay Output Module
Note
MOUNTING HOLES
9
SUPPORT STANDOFF
8573g64A.DSF
PANEL
END
MODULE
END
Installation
Mounting the Module in a Concord Cabinet
1. Remove AC panel power and disconnect the backup battery.
2. Remove and discard the module cover (Figure 2).
3. Insert a support standoff as shown in Figure 5 (supplied with panel) into the panel circuit board.
12345
6
MAGNET
CLIP
910111213
REED SWITCH
HOLDER
14 15
18
16
17
9710G02B.DSF
78
Figure 3. Mounting Holes
Mounting the Module in an Advent Cabinet
1. Remove panel AC power and disconnect the backup battery(s).
2. Remove the module cover and set it aside (Figure 2).
3. Turn the module upside down and line up the holes on
the back-plate at the desired location (Figure 4).
4. Secure the back-plate to the cabine t using three ¼-inch
#6-32 self-tapping screws (not included).
PANEL CABINET
(COVER NOT SHOWN)
Figure 5. Support Standoff
4. Slide the module back-plate onto the two clips located
on the top-left corner or center of the cabinet
(Figure 6).
The two mounting clips in the top-right corner of the
cabinet are designated for a receiver module, but if a
receiver module is not being used, the mounting clips
may be used for the 4-Relay Output Module.
5. Push the lower-right corner of the module onto the support standoff (see detail in Figure 6).
6. Gently press the module up and onto the cabinet side tab.
USABLE MOUNTING
CLIPS (6)
CARD ON
MODULE
BACK-PLATES
SIDE TAB
MOUNTED MODULE
ROOM FOR 3RD
712G11A.DSF
MODULE
Figure 4. Mounting Module in Advent Cabinet
SuperBus® 2000 4-Relay Output Module
MOUNT WITH
SELF TAPPING
SCREWS
PANEL CABINET
(COVER NOT SHOWN)
9712G08A.DSF
DETAIL
SUPPORT STANDOFF
(Included with Concord
panel accessory package)
Figure 6. Mounting Module in Concord Cabinet
3
Loading...