Interlogix 60-597 Installation Instructions Manual

Hi Tech Handheld Wireless Touchpad Installation
Instructions

Product summary

This lightweight, portable touchpad allows you to
control Concord

™

, Concord Express™, and

Advent

®

panels. You can arm and disarm your
security system, bypass sensors, control lights,
activate emergency alarms, and check system
status. Features include:

• Automated low-battery reports to the panel.

• Police, Fire, and Auxiliary panic buttons.

• Automated supervisory reports to the control

panel every 64 minutes.

• Long life (5 to 8 year) 3 V DC lithium battery.

• Wall-mount option.

Installation

Observe the following guidelines:

• Avoid mounting the touchpad near excessive

metal or electrical wiring, including furnace
and utility rooms.

• Avoid mounting in areas with excessive

moisture.

• Avoid mounting the touchpad where

temperatures exceed operating limits of 10°
to 120°F (-12° to 49°C).

• Refer to appropriate control panel

documentation for information about RF
ranges for the wireless touchpad.

To install the battery:

1. Remove cover and install battery (see

Figure 1 below).

Figure 1:

Install battery

8341G02A.DS4

2. To replace the battery cover, align the two
exposed tabs with the touchpad’s front and
back cover seam (see Figure 2 below).

3.

Press down on the battery cover and slide
into place.

Figure 2: Replacing the battery cover

EXPOSED

TAB

TOUCHPAD

SEAM

EXPOSED

TAB

Programming

Note: For SX-V Special systems, if the touchpad

is mounted on a wall or remains at the installation
site, set upper sensor number 89 to ON. If the
touchpad is to be removed from the site (i.e.
placed in an automobile), set upper sensor
number 89 to OFF.

The following steps provide a general guideline
for programming (learning) the wireless touchpad
into panel memory. Refer to specific panel
documentation for complete programming details.

1. Set your control panel to PROGRAM mode.

2. Proceed to LEARN TOUCHPAD menu.

3. Enter the ADD/PROGRAM menu to program
your wireless touchpad into panel memory.

4. Press BYPASS on the touchpad when
prompted for touchpad activation.

5. At the panel, exit the PROGRAM mode.

Testing

Remind your customer to test their security
system and wireless touchpad weekly. Refer to
the control panel documentation for complete
instructions on testing and operating the security
system.

P/N 466-1012 • REV E • Model No. 60-597 • January 2011 1 / 2

Note: A g

reen light flashes each time a number or
function button is pressed. A red and green light
flash each time a panic button is pressed.

1. Notify the central monitoring station that (1)

you are testing the security system and (2)
not to dispatch emergency services.

Technical support, www.interlogix.com/customer-support

www.utcfireandsecurity.com or www.interlogix.com

Copyright © 2011 UTC Fire & Security Company. All rights reserved

2. Arm and disarm the system with the

touchpad from various locations in order to
determine usable range.

3. Press STATUS to check the current arming

level.

4. Select Direct and Indirect to bypass sensors.

5. Press and hold each panic button until the

red/green indicator light stops flashing and
the appropriate alarm sounds.

6. Turn lights on or off (see system

documentation).

7. Press and hold the buttons marked

1 and 2

at the same time to mute the touchpad.
Continue to hold the buttons until you hear a
series of confirmation beeps.

8. Press various buttons to test the mute

feature.

9. Press and hold the buttons marked

1 and 2

at the same time to turn off the mute
function. Continue to hold the buttons until
you hear a series of confirmation beeps.

10. Contact the central monitoring station after

you have finished testing the touchpad.

Mounting the touchpad

Test the wireless touchpad at a desired location.
Ensure that a clear RF signal exists between the
touchpad and control panel. After successfully
testing for a clear RF signal, you can mount the
touchpad as follows:

1. Secure the touchpad mounting bracket to a

desired surface. Use the screws from the
accessory pack to mount the bracket (see
Figure 3 below).

Figure

3: Securing the mounting bracket

Screws

Mounting

Holes

2. Attach the touchpad to the mounting bracket

by placing the touchpad bottom into the

bracket bottom. Press the touchpad into
place to ensure a secure fit (see Figure 4
below).

Figure

4: Attach to mounting bracket

Specifications

Model no. 60-597
RF frequency 319.5
Compatibility Concord, Concord

Express, and Advent
security panels

Power requirements One 3.0 V DC lithium

battery
Battery life 5 to 8 years
Storage temperature -40° to 140°F (-34° to

60°C)
Operating
Temperature

10° to 120°F (-12° to

49°C)
Maximum Humidity 90% relative humidity,

non-condensing
Dimensions 2.1 x 0.86 x 6.1 in. (5.33 x

2.18 x 15.5 cm)

Regulatory information

Manufacturer UTC Fire & Security Americas

Corporation, Inc.
1275 Red Fox Rd., Arden Hills,
MN 55112-6943, USA

FCC compliance:
This device complies with FCC Rules Part 15.
Operation is subject to the following two
conditions:

1. This device may not cause harmful
interference.

2. This device must accept any interference that
may be received, including interference that may
cause undesired operation.
Changes or modifications not expressly
approved by Interlogix can void the user’s
authority to operate the equipment.
FCC ID No.: B4Z-861-HTTP