Intellinet Network Solutions 503358 User Manual

PoE
OFFICE
SWITCH

USER
MANUAL

MODEL 503358

INT-503358-UM-1107-01

INTRODUCTION

Thank you for purchasing the INTELLINET NETWORK SOLUTIONS™

PoE Ofce Switch, Model 503358.
This PoE Ofce Switch has eight 10/100 Base-TX ports that support

the 802.3af protocol and is designed to inject up to 19.2 Watts per port.
Any devices that are 802.3af compliant — such as IP phones, wireless
access points and network cameras — can be attached to the switch,
and no additional power will be required to support the attached device.
This eliminates the time and expense of electrical power rewiring, and
minimizes the clutter of power supplies and adapters in awkward places
such as ceilings and walls.

Besides providing 802.3af Power over Ethernet functionality, the PoE
Ofce Switch has some very impressive features as a switch. For
starters, the auto features of this switch make installation Plug and
Play and hassle free: No conguration is required. Auto-MDI/MDI-X
crossover on all ports eliminates the need for crossover cables for
connection to another switch or hub. Auto-Negotiation on each port
senses the link speed of a network device (either 10 or 100) and
intelligently adjusts for compatibility and optimal performance.

Easy-to-follow instructions in this user manual help make installation
of the switch quick and simple, so you’ll also soon be enjoying the
benets of these additional features:

• Store and forward switching architecture

• Full/half duplex operation

• IEEE 802.3x ow control for full duplex

• Zero packet loss back-pressure ow control for half duplex

• Packet ltering/forwarding rates: 148,800 pps (100 Mbps), 14,880 pps
(10 Mbps)

• Supports 4096 MAC address entries

• 128 kBytes buffer memory

• Desktop-size metal case

• LEDs for power, link/activity and PoE

• Lifetime Warranty

3

FCC Warning

This device has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses and radiates radio frequency energy and,
if not installed and used in accordance with the user manual, may cause
interference, which the user will be required to correct at his own
expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may
cause radio interference, in which case the user may be required to take
adequate measures to correct.

PORTS & INDICATORS

Ports

The eight RJ-45 connections on the front panel (at right in image below)
match workstations, servers or other network devices to 10/100 Mbps
switching ports that sense 10/100M speed and automatically negotiate
full/half duplex mode, allowing you to connect the switch to 10Base-T and
100Base-TX devices. NOTE: The eight ports are also capable of 48 V
power-injector PSE (power source equipment) function (see Connections).

2 4 6 8

2 4 6 8

PoE

LINK/ACT

POWER

PoE

LINK/ACT
1 3 5 7

1 3 5 7

4

LEDs

The front-panel LEDs (at left in image above) will be on (lighted), off or
blinking/ashing, indicating function status as follows.

POWER On: The switch has power and is ready for use.
Off: The switch has no power.
LINK/ACT On: The port is ready for 10/100 Mbps connection.
Flashing: Data is being transmitted/received at the port.
PoE On: The port is supplying power to connected device.

CONNECTIONS

ON

Power

The AC power outlet and switch are on
the rear panel (as shown at right).

OFF

PCs, Servers and Other Network Devices

Use Cat5 straight-through twisted-pair cables
to congure a network environment such
as the one shown at right.

Hubs and Other Switches

Use either straight-through or crossover cable to connect to the uplink port
of a hub or another switch: This device supports Auto-MDIX on all ports.

Powered Devices

Use Cat5 twisted-pair
cable to supply 48 V to a
powered device connected

PoE Offic e Switch

to any of the eight ports.
NOTE: Any connected
devices should also be
IEEE 802.3af compliant.

5

SPECIFICATIONS

Standards

• IEEE 802.3 (10Base-T Ethernet)

• IEEE 802.3u (100Base-TX Fast Ethernet)

• IEEE 802.3x (ow control, full duplex mode)

• IEEE 802.3af (Power over Ethernet)

• IEEE 802.1p (trafc prioritization)

General

• Media support:

- 10Base-T Cat3, 4, 5 UTP/STP RJ-45

- 100Base-TX Cat5 UTP/STP RJ-45

• Ports: 8 RJ-45 10/100 Mbps PoE ports

• Packet lter/forwarding rate: 148,800 pps (100 Mbps); 14,880 pps (10 Mbps)

• Certications: FCC Class A, CE Mark

LEDs

• Power, Link/activity for 10 and 100 Mbps, PoE

Power

• Input: 90 to 260 V AC, 50 to 60 Hz

• Power consumption: 180 Watts (maximum)

Environmental

• Metal housing

• Dimensions: 266 (W) x 160 (L) x 44 (H) mm (10.5 x 6.3 x 1.7 in.)

• Weight: 1.4 kg (3.0 lbs.)

• Operating temperature: 0 – 60°C (32 – 140°F)

• Operating humidity: 10 – 90% RH, non-condensing

• Storage temperature: -20 – 90°C (-4 – 194°F)

Package Contents

• PoE Ofce Switch

• Power cable

• User manual

6

www.intellinet-network.com

Are you completely satised with this product?

Please contact your INTELLINET NETWORK SOLUTIONS™ dealer

with comments or questions.

All produ cts mentioned are tr ademarks or registered tra demarks of their resp ective owners.

Copyri ght © I NTELLINET NET WORK

SOLUTI ONS