Contents
Before using
Compact Disc Changer
Important Safeguards........................ 2
Precautions ....................................... 3
Features............................................. 4
Supplied accessories......................... 4
Before using this unit........................ 5
CDC-3
Operation
System Connections ......................... 6
Instruction Manual
Playing CDs...................................... 7
Using memory functions ................ 13
OPEN/CLOSE
STOPPAUSE
PLAY
REPEATRANDOM
/ /
DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 DISC 6
by
CDC-3
POWER
OFF
ON
Thank you for purchasing the Integra Compact Disc
Changer.
Please read this manual thoroughly before making
connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new Compact Disc Changer.
Please retain this manual for future reference.
MEMORY CLEAR
NEXT SELECTION
DISPLAY
6 DISC
FIVE CD EXCHANGE CONTINUOUS PLAY
DISC SKIP
Appendix
Control positions and names .......... 15
Troubleshooting Guide................... 16
Specifications ................................. 16
1.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Important Safeguards
Read Instructions – All the safety and operating instructions
should be read before the appliance is operated.
2. Retain Instructions – The safety and operating instructions
should be retained for future reference.
3.
Heed Warnings
operating instructions should be adhered to.
4.
Follow Instructions
should be followed.
5.
Water and Moisture
water – for example, near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool, and
the like.
6.
Carts and Stands
cart or stand that is recommended by the manufacturer.
6A.An appliance and cart combi-
nation should be moved with
care. Quick stops, excessive
force, and uneven surfaces may
cause the appliance and cart
combination to overturn.
7.
Wall or Ceiling Mounting
to a wall or ceiling only as recommended by the manufacturer.
8.
Ventilation
tion or position does not interfere with its proper ventilation.
For example, the appliance should not be situated on a bed,
sofa, rug, or similar surface that may block the ventilation
openings; or if placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the
ventilation openings, there should be free space of at least 5 cm
(2 in.) and an opening behind the appliance.
9.
Heat
– The appliance should be situated away from heat
sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
– All warnings on the appliance and in the
– All operating and use instructions
– The appliance should not be used near
– The appliance should be used only with a
PORTABLE CART WARNING
S3125A
– The appliance should be mounted
– The appliance should be situated so that its loca-
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
10.
Power Sources –
power supply only of the type described in the operating
instructions or as marked on the appliance.
11.
Polarization
having one blade wider than the other, please read the following
information:
The polarization of the plug is a safety feature. The polarized plug
will only fit the outlet one way . If the plug does not fit fully into the
outlet, try reversing it. If there is still trouble, the user should seek
the services of a qualified electrician. Under no circumstances
should the user attempt to defeat the polarization of the plug.
12.
Power-Cord Protection
routed so that they are not likely to be walked on or pinched by
items placed upon or against them, especially near plugs, convenience receptacles, and the point where they exit from the
appliance.
13.
Cleaning
mended by the manufacturer.
14.
Nonuse Periods
unplugged from the outlet when left unused for a long period
of time.
15.
Object and Liquid Entry
objects do not fall and liquids are not spilled into the enclosure
through openings.
16.
Damage Requiring Service
viced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or
E. The appliance has been dropped, or the enclosure damaged.
17.
Servicing
beyond that described in the operating instructions. All other ser vicing should be referred to qualified service personnel.
– The appliance should be cleaned only as recom-
appliance; or
exhibits a marked change in performance; or
– The user should not attempt to service the appliance
The appliance should be connected to a
– If the appliance is provided with a polarized plug
– Power-supply cords should be
– The power cord of the appliance should be
AVIS
RISQUE DE CHOC ELECTRIQUE
– Care should be taken so that
– The appliance should be ser-
OUVRIR
NE PAS
2
Precautions
For U.S. model
The laser is covered by a housing which prevents exposure during
operation or maintenance. However, this product is classified as a
Laser Product by CDRH (Center for Devices and Radiological
Health) which is a department of the Food and Drug Administration. According to their regulations 21 CFR section 1002.30, all
manufactures who sell Laser Products must maintain records of
written communications between the manufacturer, dealers and
customers concerning radiation safety. If you have any complaints
about instructions or explanations affecting the use of this product,
please feel free to write to the address on the back page of this
manual. When you write us, please include the model number and
serial number of your unit.
In compliance with Federal Regulations, the certification, identification and the period of manufacture are indicated on the rear
panel.
FCC INFORMATION FOR USER
CAUTION:
The user changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
For Canadian model
CAUTION:
EXCEED THE CLASS B LIMITS FOR RADIO NOISE EMISSION FROM DIGITAL APPARATUS SET OUT IN THE RADIO
INTERFERENCE REGULATIONS OF THE CANADIAN
DEPARTMENT OF COMMUNICATIONS.
For models having a power cord with a polarized plug:
CAUTION:
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
THIS DIGITAL APPARATUS DOES NOT
TO PREVENT ELECTRIC SHOCK, MATCH
Modele pour les Canadien
ATTENTION:
GÉNÉRÉE PAR CET APPAREIL NUMÉRIQUE DE TYPE B NE
DÉPASSE PAS LES LIMITES ÉNONCÉES DANS LE RÈGLEMENT SUR LES PERTURBATIONS RADIO ÉLECTRIQUES,
SECTION APPAREIL NUMÉRIQUE, DU MINISTÈRE DES
COMMUNICATIONS.
Sur les modèles dont la fiche est polarisée:
ATTENTION:
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
L'INTERFÉRENCE RADIO ÉLECTRIQUE
POUR ÉVITER LES CHOCS ÉLECTRIQUES,
3
Remote controller RC-331C × 1
Batteries (size AA, R6 or UM-3) × 2
Audio connection cable × 1
cable
× 1
Power cable × 1
Precautions
1. Warranty Claim
You can find the serial number on the rear panel of this unit. In case
of warranty claim, please report this number.
2. Power WARNING
BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME,
READ THE FOLLOWING SECTION CAREFULLY.
The voltage of the available power supply differs according to
country or region. Be sure that the power supply voltage of the area
where this unit will be used meets the required voltage (e.g., AC
230 V, 50 Hz or AC 120 V, 60 Hz) written on the rear panel.
3. Do not touch this unit with wet hands
Do not handle this unit or power cord when your hands are wet or
damp. If water or any other liquid enters the case, take this unit to
an authorized service center for inspection.
4. Location of this unit
Place this unit in a well-ventilated location.
T ake special care to pro vide plenty of v entilation on all sides of this
unit especially when it is placed in an audio rack. If ventilation is
blocked, this unit may overheat and malfunction.
Do not expose this unit to direct sunlight or heating units as this
unit’s internal temperature may rise and shorten the life of the
pickup.
A void damp and dusty places and places directly affected by vibrations from the speakers. In particular, avoid placing the unit on or
above one of the speakers.
Be sure this unit is placed in a horizontal position. Never place it
on its side or on a slanted surface as it may malfunction.
Do not place near tuners or TV sets.
If placed next to a TV or tuner, it may cause reception interference
resulting in some noise in the TV or tuner output.
5. Care
From time to time you should wipe the front and rear panels and the
cabinet with a soft cloth. For heavier dirt, dampen a soft cloth in a
weak solution of mild detergent and water, wring it out dry, and
wipe off the dirt. Following this, dry immediately with a clean cloth.
Do not use rough material, thinners, alcohol or other chemical solvents or cloths since these could damage the finish or remove the
panel lettering.
6. Points to remember
If this unit is brought from a cold environment to a warm one or is
in a cold room that is quickly heated, condensation may form on
the pickup, preventing proper operation. In this case, remove the
disc and leave the power ON for about one hour to remo v e the condensation.
When transporting this unit, be careful not to bump it.
Always close the disc tray when not loading or unloading discs to
protect delicate internal parts from dust.
Features
■
6-Disc Carousel Changer – only from Onkyo – offers
more music and convenience for the money
■
Unique design allows users to change up to 5 discs
without interrupting disc in play
■
Next Selection – another Onkyo exclusive – lets users
choose the next track/disc without interrupting the
current song playing
■
Single-Bit PWM (Pulse Width Modulation) D/A Converter to minimize lowlevel linearity problems that
plague many multi-bit players – so there’s no loss of
musical detail during quieter passages
■
ProprietaryAccuPulse Quartz System with Polysorb
virtually eliminates the possibility of timing errors in
the clock oscillator
■
8-Times Oversampling
■
Fixed Analog Output
■
Visible Display when tray is out
■
Oversized power transformer
■
6-Mode Repeat: entire disc, all discs, random tracks,
programmed tracks, random memory, single track
■
3-Mode Time Display: Single, Elapse/Remain, Total
Remain
■
Compatible Remote Control
■
Disc Intro Scan plays the first 8 seconds of each disc
■
Direct Track/Disc Access via remote
■
Optical Digital Output for direct digital connection to
DAT/Minidisc player or DSP receiver.
Supplied accessories
Check that the following accessories are supplied with this unit.
Memory Preservation
This unit does not require memory preservation batteries. A
built-in memory power back-up system preserves the contents
of the memory during power failures and even when the unit is
unplugged. The unit must be plugged-in in order to charge the
back-up system.
The memory preservation period after the unit has been
unplugged varies depending on climate and placement of the
unit. On the average, memory contents are protected over a
period of a few weeks after the last time the unit was
unplugged. This period is shorter when the unit is exposed to a
highly humid climate.
4
Before using this unit
Inserting the remote controller batteries
Insert the batteries into the remote controller
following the illustration below.
1
2
3
Remote control sensor
30°
30°
CDC-3
approx. 5 m
(16 feet)
1. Remove the battery compartment cover by opening it as shown
in the illustration.
2. Insert two AA (R6- or UM-3)-size batteries into the battery compartment. Carefully follow the polarity diagram (positive (+) and
negative (–) symbols) inside the battery compartment.
3. After batteries are installed and seated correctly, replace the compartment cover.
Notes:
•
Do not mix new batteries with old batteries or different kinds of
batteries.
•
To avoid corrosion, remove the batteries if the remote controller
is not to be used for a long time.
•
Remove dead batteries immediately to avoid damage from corrosion. If the remote controller doesn’t operate smoothly,
replace both the batteries at the same time.
•
The life of the batteries supplied is about six months but this
will vary depending on usage.
Using the remote controller
Point the remote controller toward the remote control sensor.
Notes:
Place the unit away from strong light such as direct sunlight or
•
inverted fluorescent light which can prevent proper operation of
the remote controller.
•
Using another remote controller of the same type in the same
room or using the unit near equipment which uses infrared rays
may cause operational interference.
Do not put any object such as a book on the remote controller.
•
The buttons of the remote controller may be pressed by mistake
and drain the batteries.
Make sure the audio rack doors do not have colored glass. Plac-
•
ing the unit behind such doors may prevent proper remote controller operation.
•
If there is any obstacle between the remote controller and the
remote control sensor, the remote controller will not operate.
Playable Discs
This CD player can play back the following discs.
Disc mark Contents Disc size
Audio
CDs
You cannot play back discs other than those listed above.
Do not use discs that are not audio discs (eg. CD-ROMs for use
with personal computers), as these could damage the speakers and
amplifier.
Avoid using heart-shaped or octagonal discs. Playing irregularly
shaped discs may damage the internal mechanism of the CD player.
Do not use discs on which adhesive from adhesive tape or a disc
label (if it is a rental disc) remains. Otherwise, you may not be able
to eject the discs or the CD player may become inoperative.
Audio
12 cm 74 minutes
8 cm
(CD single)
Maximum
playback time
20 minutes
5
System Connections
•
Do not plug in the power cord until all connections have been made.
•
On each pair of input or output jacks, the jack marked R corresponds to the right channel and the jack marked L corresponds to the left
channel.
AC INLET
AVIS
WARNING
RISK OF ELECTRIC SHOCK
RISQUE DE CHOC ELECTRIQUE
DO NOT OPEN
L
R
ANALOG
OUTPUT
NE PAS OUVRIR
REMOTE
CONTROL
DIGITAL
OUTPUT
OPTICAL
COMPACT DISC CHANGER
MODEL NO.
CDC-3
RATING:
AC120V 60Hz 10W
2-1, NISSHIN- CHO, NEYAGAWA-SHI, OSAKA,
JAPAN MANUFACTURED IN MALAYSIA
Audio
connection cable
LR
CD
Amplifier
cable
Optical fiber cable
(not included)
Optical IN
DAT, MD recorder or
Digital amplifier
Connecting to an audio system
Two types of output jacks are located on the rear panel.
Use the DIGITAL OUTPUT jack if you are connecting the unit to
audio equipment that supports a digital connection.
ANALOG OUTPUT jacks:
These are the most commonly used jacks. Connect these jacks to
the amplifier’s CD input jacks using the supplied audio connection
cable.
DIGITAL OUTPUT (optical output) jack:
For digital recording, connect this jack to the digital input jack of a
Mini Disc recorder, a D AT deck, or other digital equipment. If your
amplifier has a digital input jack, connecting the DIGITAL OUTPUT jack to it will produce a much clearer and more dynamic
sound.
Terminal protection cap is attached to the digital jack.
•
Remove the cap when connecting the unit to other digital equipment. When you are not using the digital output jack, replace
the cap.
Refer to the amplifier’s instruction manual for connections.
•
To wall
outlet
Connecting a power cable
1. Connect the outlet plug on the included power
cable to the AC INLET on the CDC-3.
2. Plug-in the other end of the cable to a wall AC
outlet.
Note:
• Do not use any power cable other than the included
cable. The included cable is designed for use only
with the CDC-3. Do not use it for any other device.
• Do not connect or disconnect the outlet plug from
the CDC-3 while the other end is plugged into the
wall AC outlet.
Connections for remote controller ( )
When connecting Onkyo/Integra products, it is necessary to attach
the cable to be able to use the remote controller of the main
component to control the entire system.
1. To use this CD changer with an amplifier (or receiver), cassette
tape deck, and tuner that include the appropriate jack, connect the components using the cable, plugged into the
REMOTE CONTROL jacks.
2. As the exact connection sequence of the cable is unimportant, you can connect from the amplifier (or receiver) to either the
tuner, cassette tape deck, or compact disc changer.
3. To operate correctly, the remote controller must point toward the
remote control sensor of the amplifier (or receiver).
Notes:
•
The upper and lower REMOTE CONTROL jacks have the
same function.
Remote controller operation is not possible when only the
•
cable is connected – the audio connection cables must also be
connected.
An cable equipped with a 3.5mm (1/8 in.) diameter minia-
•
ture two-conductor phone plug is included with this unit and
with every tuner and cassette tape deck that utilizes the
jack.
6
12
POWER
Connecting the power
Before plugging in the unit, confirm that all connections have been
made properly.
1.
To AC
outlet
OFFON
Insert the AC power supply cord into the outlet.
2.
Press the POWER button.
•
When the power first turns on, the carousel rotates to find a disc
and stops automatically if there is a disc on the disc tray.
Playing CDs
1, 3
2
POWER
OFF
ON
DISPLAY
0
CUSTOM
+10
MEMORY CLEAR
ERASE
FILE
6 DISC
FIVE CD EXCHANGE CONTINUOUS PLAY
NEXT SELECTION
162738495
OPEN/CLOSE
DISC SKIP
STOPPAUSE
PLAY
DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 DISC 6
COMPACT DISC CHANGER
DX-C540
4
1
Normal playback
1. Press the OPEN/CLOSE button to open the loading
OPEN/CLOSE
drawer.
2. Place the disc(s) in the disc trays with the label(s) facing up.
Front
disc tray
Pressing the DISC SKIP button rotates the carousel so that you
•
can load disc(s) in other disc trays.
•
The disc tray with the Disc Number marked by a circle on the
indicator will come to the front.
The carousel usually rotates counter-clockwise. However, it
•
2
may sometimes rotate clockwise when you press the DISC
SKIP button four times repeatedly.
•
DISC SKIP
If you place the discs in the disc trays and press the PLAY button instead of the OPEN/CLOSE button, the drawer will
close, the carousel will rotate, and the unit will start playing
back the disc in the front disc tray.
3. Press the OPEN/CLOSE button again to close the loading
drawer.
When you close the loading drawer, the unit will read the disc in
3
OPEN/CLOSE
the front disc tray and display the number of tracks and the
recording time in the disc.
If there is no disc in this tray, the carousel rotates until it finds a
disc tray with a disc. Disc Numbers with empty trays disappear
from the display.
4. Press the PLAY button.
The unit will start playing back the disc from the first track.
After the CD changer completes playing back all discs on the
TRACK
TOTAL REMAIN
DISC No.
123
4
carousel, the display returns to the view shown in step 3.
4
PLAY
Changing a disc during playback
1. Press the OPEN/CLOSE button during playback.
2. Press the DISC SKIP button.
The carousel will turn so that you can change a disc other than
the one that is playing.
PAUSE
TRACK
SINGLE ELAPSED
DISC No.
123
4
3. Press the OPEN/CLOSE button to close the loading drawer.
Note:
Y ou cannot select a ne w disc to play if the loading drawer is open. When
you finish changing discs, close the loading drawer immediately .
1
Important notes on handling CDs
1. Carefully lift the disc from the disc case, making sure to hold
the disc by its edges or the hole in the center.
2. You may use a dry, soft cloth to wipe dust and fingerprints from
the surface of CDs. Do not use volatile agents on discs, such as
2
thinner or benzine. Also, do not use conventional record cleaner
or antistatic agents.
Do not place a CD in direct sunlight or locations subject to high
•
humidity or low temperature.
Do not store a CD in the CD changer tray for a long period of
•
time.
7
Playing CDs
PAUSE
STOP
DISPLAY
PAUSE
STOP
POWER
OFF
ON
DISPLAY
0
CUSTOM
+10
MEMORY CLEAR
ERASE
FILE
6 DISC
FIVE CD EXCHANGE CONTINUOUS PLAY
NEXT SELECTION
162738495
OPEN/CLOSE
DISC SKIP
STOPPAUSE
PLAY
DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 DISC 6
COMPACT DISC CHANGER
DX-C540
/
/
Stopping playback temporarily
Press the PAUSE button.
The PAUSE indicator will light up. To resume playback, press the
PLAY button, or press the PAUSE button again. The CD changer
starts playing again from exactly the point at which it stopped.
Stopping playback
Press the STOP button.
When you open the loading drawer, the disc that was playing
•
will be in the front disc tray.
TRACK
TRACK
TRACK
/ /
PLAY
DISPLAY
DISPLAY
SINGLE ELAPSED
SINGLE
REMAIN
REMAINTOTAL
REMOTE CONTROLLER RC-331C
DISC No.
DISC No.
DISC No.
a
123
456
b
123
456
c
123
456
DISPLAY
Search play
Hold down the / button to fast forward the current track
during playback.
Hold down the / button to fast reverse the current track
during playback.
Release the / or / button when you reach the point
on the track you want to play back.
You can also use the remote controller to search by using the
and buttons instead of the / and / buttons.
•
The unit starts fast forwarding at 10-times speed, and after four
seconds at 60-times speed.
During the fast forward operation, you will hear a cueing sound
•
at low volume.
•
When the end of the disc is reached, the unit will play back the
next disc.
If you locate the top of the disc, the unit will cancel the fast for-
•
ward operation and start playing back from the top of the disc
(Track 1).
Checking the elapsed or remaining time
Press the DISPLAY button during playback.
d
The display changes each time you press the DISPLAY button.
SINGLE ELAPSED: Indicates how long the current track has
been playing.
SINGLE REMAIN: Indicates how much time is left for the current track. For beyond the 20th track, the unit displays “--: --”.
TOTAL REMAIN: Indicates how much time is left for the
entire disc to play. During memory play, this display indicates
the playing time remaining for the entire sequence of tracks
programmed into memory.
The display returns to SINGLE ELAPSED time display.
8
Playing CDs
PLAY
162738495
POWER
+10
OFF
ON
DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 DISC 6
DISC 1 DISC 2 DISC 3
DISC 4 DISC 5 DISC 6
REMOTE CONTROLLER RC-331C
NEXT SELECTION
DISPLAY
0
CUSTOM
MEMORY CLEAR
ERASE
FILE
6 DISC
FIVE CD EXCHANGE CONTINUOUS PLAY
OPEN/CLOSE
DISC SKIP
STOPPAUSE
PLAY
DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 DISC 6
COMPACT DISC CHANGER
DX-C540
/
/
Starting playback from a given disc
Press the Direct Play button of a disc you wish to play back
(DISC 1-DISC 6) on the front panel or the remote controller.
The unit will play back the selected disc.
•
If you press the Direct Play button (DISC 1-DISC 6) during
•
playback, the playback will be cancelled and the unit will start
playing back Track 1 of the selected disc.
•
If you press the DISC SKIP button during playback, the playback will be cancelled and the unit will start playing back Track
1 of the next disc. (If the playback of Disc 6 is cancelled, the
unit will start playing back Disc 1.)
•
You can select a disc by pressing the DISC SKIP button while
the playback is stopped. After you select a disc, press the PLAY
button to start playback from Track 1.
/ /
REMOTE CONTROLLER RC-331C
123
456
789
+10 0
PLAY
Starting playback from a given track
Using Skip buttons to select a playback track
1. While the unit is stopped, press the / or /
button to select a track.
•
Do not hold down the button. Press it repeatedly.
•
The Track indicator section will display the selected track number.
2. Press the PLAY button.
The unit will start playing back from the selected track.
•
Using the number buttons to select a playback
track
1. Select the track number you wish to play back using the
number buttons.
The CD changer will start playing automatically. You do not
need to press the PLAY button.
•
The +10 number button is used to select a track with a number
of 10 or higher. For example, to select Track Number 30, press
this button three times, and then press 0.
•
If you do not select a track, playback will start from the first
track on the selected disc.
9
Playing CDs
/
TRACK
/ /
STOP
SINGLE
/
REMAIN
REMOTE CONTROLLER RC-331C
DISC No.
162738495
POWER
CUSTOM
+10
FILE
OFF
ON
123
456
NEXT SELECTION
DISPLAY
0
MEMORY CLEAR
ERASE
6 DISC
FIVE CD EXCHANGE CONTINUOUS PLAY
OPEN/CLOSE
DISC SKIP
STOPPAUSE
PLAY
DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 DISC 6
COMPACT DISC CHANGER
DX-C540
/
Skip playback
Use the / and / buttons.
You can also use the remote controller to operate the unit by using
the and buttons instead of the / and /
buttons.
During playback, press the
The CD changer will stop playing the current Track and will begin
playing the next track from the beginning.
During memory playback (see “Using memory functions” on
page 13), pressing this button will skip to the top of the next memorized track or the next disc.
Pressing this button during random playback (see “Playing back
tracks at random” on page 12) will stop the playback, and the unit
will select the next song at random and start playing it back.
During playback, press the
The CD changer will return to the beginning of the current track
and will begin playing back the same track again. To jump back to
the previous track, quickly press the / button again before
playback begins.
During memory playback, pressing this button will skip to the top
of the previous track or disc.
Pressing this button during random playback will locate the top of
the current track, not the previous track.
/
/
button.
button.
TRACK
TRACK
DISC No.
SINGLE
REMAIN
/
123
456
•
The / button is disabled when the unit is playing back
the last track of the disc or the last stored track.
•
When the first track of the disc (Track 1) or the first stored track
is being played back, the / button serves only to locate
the top of the track.
SINGLE
REMAIN
DISC No.
123
456
/
Checking the playing time of a track
When you press the / button, the display indicates the
playing time of the next track, in the order of the tracks on the
CD.
•
When you press the / button, the display shows the
playing time of the previous track.
Continuously listening to the beginning of discs
(Disc intro scan)
DISC
INTRO SCAN
REMOTE CONTROLLER RC-331C
The “disc intro scan” function is particularly useful for quickly
checking the contents of discs.
To activate this function, press the DISC INTRO SCAN button on
the remote controller.
The CD changer will play back only the beginning of each disc for
about eight seconds.
10
Playing CDs
1
NEXT SELECTION
TRACK
2
DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 DISC 6
TRACK
3
123
456
REMOTE CONTROLLER RC-331C
789
+10 0
REMOTE CONTROLLER RC-331C
/ /
NEXT SELECTION
POWER
OFF
ON
NEXT DISC No.
NEXT DISC No.
1
NEXT SELECTION
162738495
DISPLAY
0
CUSTOM
+10
MEMORY CLEAR
ERASE
FILE
NEXT SELECTION
123
456
123
456
6 DISC
FIVE CD EXCHANGE CONTINUOUS PLAY
3
OPEN/CLOSE
DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 DISC 6
DISC SKIP
COMPACT DISC CHANGER
2
STOPPAUSE
PLAY
DX-C540
Selecting the next track to play back
This function enables you to select the next track or disc to play back.
1. Press the NEXT SELECTION button during playback.
2. Select the disc you wish to play using the Direct Play buttons
(DISC 1-6).
• You can also use the DISC SKIP button to select a disc.
• To indicate that you wish to play the entire disc, press the
NEXT SELECTION button at this point. (AL means all tracks)
• If you do not select a disc within approximately eight seconds,
your disc selection will be cancelled. In this case, try Steps 1
and 2 again.
3. Select the track number you wish to play using the /
and / buttons and then press the NEXT SELECTION button.
When the playback of the current track is complete, the selected
track will play.
You can use the number buttons on the remote controller to
select a track number. In this case, you do not need to press the
NEXT SELECTION button.
• If you select an entire disc to play back, the unit will first com-
plete playback of the current disc, then play back the selected
disc. If you select a track to play back, the unit will first complete playback of the current track, then play back the selected
track.
• You can use the Next Selection function during memory play-
back, random playback, and memory random playback (see
“Using memory functions” on page 13, and “Playing back
tracks at random” on page 12). In these cases, the unit will first
complete playback of the current track, then start playing back
the selected disc or track, and the memory playback, random
playback, or memory random playback will be cancelled.
Note:
• If after making your selection, you use the DISC SKIP /
and / button, or the number buttons to change the
track for playback, the settings will be cancelled.
• The Next Selection function is ef fecti v e only once at a time. The
function will be cancelled when the selected disc or track starts
playing back after playback of the current disc or track is completed.
• If you press the STOP button, the setting will be cancelled.
To select another disc or track ...
Press the NEXT SELECTION button. The currently-selected disc
or track number will flash on the panel. You can change this number in the usual way.
To cancel the selection ...
Press the NEXT SELECTION button. The selected disc or track
number will flash on the panel. Press the CLEAR button, and the
selected disc or track will be cancelled. Press the NEXT SELECTION button.
• The NEXT SELECTION indicator will turn off.
11
Playing CDs
REPEAT
RANDOM
TRACK
TRACK SINGLE ELAPSED
RANDOM DISC No.
SINGLE ELAPSED
RANDOM DISC No.
REMOTE CONTROLLER RC-331C
POWER
ON
RANDOM
OFF
162738495
CUSTOM
+10
FILE
NEXT SELECTION
DISPLAY
0
MEMORY CLEAR
ERASE
FIVE CD EXCHANGE CONTINUOUS PLAY
123
456
123
456
OPEN/CLOSE
STOPPAUSE
PLAY
DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 DISC 6
DISC SKIP
6 DISC
COMPACT DISC CHANGER
DX-C540
RANDOM
Playing back tracks at random
Press the RANDOM button on the unit or the remote contr oller
to enter random mode.
The CD changer will play all tracks on all six discs at random.
• To cancel random play, press the STOP or RANDOM button.
• The unit stops when it completes playback of all tracks on all
discs.
If you have pressed the REPEAT button, the unit will repeat playback of all tracks at random after it finishes playing all tracks once.
• During random playback, the DISC 1 - DISC 6 buttons, the
DISC SKIP button, and the number buttons will be disabled.
• Discs can be exchanged during random playback. However, if
you add a disc with a different number of tracks, all tracks will
be played back. A disc that contains the same number of tracks
will not play back track numbers that have already been played.
If a disc for which all tracks have been played is exchanged, the
new disc is not played.
• Random mode can be operated together with memory mode and
repeat mode. However, if the whole disc is stored into memory
and the disc is selected, no other songs are played until the ran-
dom playback of tracks from this disc is completed. (Refer to
“Using memory functions” on page 13 for more information on
memory playback.)
REPEAT
PLAY
TRACK
TRACK
REPEAT
REPEAT
REMOTE CONTROLLER RC-331C
TOTAL REMAIN
SINGLE ELAPSED
REPEAT
NEXT
DISC No.
DISC No.
123
456
123
456
Repeating all tracks of all discs
1. Press the REPEAT button on the unit or the remote control-
ler to enter the repeat mode.
The REPEAT indicator will light up.
2. Press the PLAY button.
All tracks from all discs inserted in the disc trays will be played
back repeatedly.
Repeat playback can be used with normal, random, and mem-
ory playback modes (see “Using memory functions” on
page 13). You can press this button either before or during play-
back.
3. To cancel the repeat mode, press the REPEAT button to
turn off the repeat indicator.
12
Using memory functions
3
POWER
OFF
ON
DISPLAY
0
CUSTOM
+10
MEMORY CLEAR
ERASE
FILE
6 DISC
FIVE CD EXCHANGE CONTINUOUS PLAY
NEXT SELECTION
162738495
OPEN/CLOSE
DISC SKIP
41
STOPPAUSE
PLAY
DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 DISC 6
COMPACT DISC CHANGER
DX-C540
2
Storing a program into memory and playing it
1
MEMORY CLEAR
REMOTE CONTROLLER RC-331C
2
3
DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 DISC 6
DISC 1 DISC 2 DISC 3
DISC 4 DISC 5 DISC 6
REMOTE CONTROLLER RC-331C
/ /
REMOTE CONTROLLER RC-331C
123
456
789
+10 0
MEMORY
MEMORY CLEAR
MEMORY
Up to 40 tracks can be stored in memory.
1. Press the MEMORY button.
The MEMORY indicator will light up.
2. Select the desired disc using the Direct Play buttons (DISC
1-6).
• You may also use the DISC SKIP button to select a disc.
• If you wish to program the entire disc, select the desired disc
and press the MEMORY button. (“AL (all)” appears.)
• To use the number buttons on the remote controller to select the
entire disc, press the “0” button.
3. Use the / and / buttons to select the desired
track, and then press the MEMORY button.
The selected tracks are stored in memory.
You can use the number buttons on the remote controller to select a
track number. In this case, you do not need to press the MEMORY
button.
• To store tracks on other discs into the memory, repeat steps 2
and 3.
• Repeat Step 3 to select a track from the same disc.
• If you attempt to select more than 40 tracks, “FULL” will flash
on the time display to indicate that the memory is full.
4. Press the PLAY button.
The CD changer will play the programmed tracks in the order
you selected.
• If you press the MEMORY button during playback, the track
being played will be stored in memory. You can use the number
buttons to program more tracks.
• You will need to select a disc each time you wish to program a
track from a non-current disc.
Notes:
• If the total remaining time is more than 99 minutes 59 seconds
or when the contents of the memory extends to 2 or more discs,
“--:--” will be displayed.
• If a selected disc or track does not exist, the corresponding indi-
cator (disc or track) will light up and the selection will be
included in the program count, but the selection(s) will be
ignored and the subsequent disc or track in the program will
play.
Stopping a memory playback
4
PLAY
REMOTE CONTROLLER RC-331C
Press the STOP button.
13
Using memory functions
TRACK
After two seconds
TRACK
MEMORY CLEAR
a
b
Contents of the display
Example: When the sixth track of DISC #5 is stored in memory as
MEMORY DISC No.
123
456
the second track to play back (P-02).
Track number
MEMORY indicator
Program number
Disc Number
Total number of stored programs
MEMORY DISC No.
REMAIN
TOTAL
c
d
123
456
e
Clearing the last track stored
Press the CLEAR button.
CLEAR
REMOTE CONTROLLER RC-331C
The last track stored in memory is cleared.
MEMORY CLEAR
TRACK
REMOTE CONTROLLER RC-331C
/ /
MEMORY DISC No.
MEMORY
123
456
Clearing the entire program
Press the MEMORY button.
The contents of memory are completely cleared.
Checking what is stored in memory
1. First, if the CD changer is playing in memory playback
mode, press the STOP button. The CD changer will display
the last program number stored in memory.
2. If you press and hold down the / button, the track
numbers in memory will appear in the display in the order
in which they were stored. If you press and hold down the
/ button, the track numbers will appear in the oppo-
site order.
14
REMOTE CONTROLLER RC-331C
Control positions and names
Note:
• If there is a protective film on the surface of the display that makes it difficult to read the display, remove it.
• For more information about the buttons and knobs, refer to the pages listed in the brackets ( [ ] ) below.
1
POWER
ON
10 11
23 5 7 94 6
NEXT SELECTION
DISPLAY
OFF
MEMORY CLEAR
6 DISC
FIVE CD EXCHANGE CONTINUOUS PLAY
12
13
a
14
PAUSE REPEAT RANDOM MEMORY NEXT DISC No.
bcd
OPEN/CLOSE
DISC SKIP
15 16
8
PLAY
STOPPAUSE
REPEATRANDOM
CDC-3
/ /
by
DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 DISC 6
1817
19
e
123
TRACK SINGLE ELAPSED
TOTAL REMAIN
f
hg
456
Front panel
1. POWER button [6]
2. NEXT SELECTION button [11]
3. DISPLAY button [8]
4. Remote control sensor [5]
5. Display
6. OPEN/CLOSE button [7]
7. PAUSE button [8]
8. STOP button [8, 10]
9. PLAY button [7~9, 12, 13]
10. MEMORY button [13, 14]
11. CLEAR button [14]
1
2
3
4
5
NEXT SELECTION
DISC 1 DISC 2 DISC 3
DISC 4 DISC 5 DISC 6
123
456
789
+10 0
REMOTE CONTROLLER RC-331C
12. Loading drawer
13. Carousel
14. Disc trays
15. DISC SKIP buttons [7]
16. Direct play buttons
(DISC 1-DISC 6) [9, 11, 13]
17. RANDOM button [12]
18. REPEAT button [12]
19. Search/Skip buttons
( / , / ) [8~11, 13, 14]
DISC
INTRO SCAN
RANDOM
REPEAT
MEMORY
CLEAR
6
7
8
9
10
Display
a. PAUSE indicator
b. REPEAT indicator
c. RANDOM indicator
d. MEMORY indicator
e. Disc number indicator
f. Track number indicator
g. ELAPSED/REMAIN indicators
h. Time display
Remote controller
1. Open/close button [7]
2. Operation buttons
: Pause button [8]
: Stop button [8, 10]
: Play button [7~9, 12, 13]
: Fast reverse button [8, 14]
: Fast forward button [8, 14]
: Reverse skip button [10, 13]
: Forward skip button [10, 13]
3. NEXT SELECTION button [11]
4. Direct play buttons
(DISC 1-DISC 6) [9, 11, 13]
5. Number buttons and +10 button [9, 11, 13]
6. DISC INTRO SCAN button [10]
7. RANDOM button [12]
8. REPEAT button [12]
9. MEMORY button [13, 14]
10. CLEAR button [14]
15
Tr oubleshooting Guide
Specifications
• No power.
Cause: Power cable is not properly plugged into the AC outlet.
Remedy: Insert the power plug firmly.
• A disc is loaded in the disc tray, but playback will not start.
Cause: A disc in the disc tray may be upside down.
Remedy: Load the disc with the label facing upward.
Cause: The disc is dirty.
Remedy: Clean the disc.
Cause: Moisture has accumulated inside the CD changer.
Remedy: Remove the disc from the disc tray, place the CD
changer in a warm place, and leave the power on for
about one hour.
• No sound is heard.
Cause: Connections may be incomplete or incorrect.
Remedy: Check all cable connections. Insert all the plugs firmly
into the jacks.
Cause: The input selector switch on the amplifier may be set incor-
rectly.
Remedy: Set the switch to the proper position. See your ampli-
fier’s operating instructions for more information.
• Disc playback skips.
Cause: The disc is dirty.
Remedy: Clean the disc.
Cause: A disc is scratched.
Remedy: Replace the disc.
Cause: The CD changer is subject to being accidentally bumped.
Remedy: Place the CD changer in a more stable location.
• Search time (when locating a specific track) is extremely
long.
Cause: The disc is dirty.
Remedy: Clean the disc.
Cause: The disc is scratched.
Remedy: Replace the disc.
• Track numbers cannot be stored in memory.
Cause: No disc in the tray.
Remedy: Load a disc in the tray.
Cause: You have entered a track number that does not exist on the
disc.
Remedy: Use only the track numbers that exist on the disc.
• Front panel controls function correctly, but remote control-
ler does not.
Cause: No batteries in remote controller.
Remedy: Insert batteries.
Cause: Batteries have worn out.
Remedy: Replace batteries.
Signal readout system: Optical non-contact
Reading rotation: About 500 - 200 r.p.m.
(constant linear velocity)
Linear velocity: 1.2 - 1.4 m/s
Error correction system: Cross Interleave Reed-Solomon code
D/A converter: 1 bit PWM/ACCUPULSE
Sampling frequency: 352.8 kHz (8 times oversampling)
Number of channels: 2 (stereo)
Frequency response: 5 Hz - 20 kHz
Total harmonic distortion: 0.005% (at 1 kHz)
Dynamic range: 96 dB
Signal to noise ratio: 92 dB
Channel separation: 92 dB (at 1 kHz)
Wow and Flutter: Below threshold of measurability
Output level: 2 volts r.m.s.
Power consumption: 10 watts
Power supply: AC 120 V, 60 Hz
Dimensions (W × H × D): 435 × 131 × 433mm
(17-1/8" × 5-3/16" × 17-1/16")
Weight: 6.9 kg (15.2 lbs.)
Specifications and features are subject to change without notice.
Because the unit contains a microcomputer to provide advanced
functions, it may malfunction due to external noise or static electricity. If this happens, press the POWER switch on the unit and
then press it in again after about five seconds.
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 0720-31-8111 Fax: 0720-33-5222
ONKYO U.S.A. CORPORATION
200 Williams Drive, Ramesy, N.J. 07446, U.S.A.
Tel: 201-825-7950 Fax: 201-825-8150 E-mail: onkyo@onkyousa.com
ONKYO EUROPE ELECTRONICS GmbH
Industriestrasse 20, 82110 Germering, GERMANY
Tel: 089 84 93 20 Fax: 089 84 93 226 E-mail: info@onkyo.de
ONKYO CHINA LIMITED
Units 2102-7, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,
N.T., HONG KONG Tel: 852 2429 3118 Fax: 852 2428 9039
16
SN 29342785
HOMEPAGE
http://www.onkyo.co.jp/
I9905-1
E
Loading...