• Works with a TV and a cable,
satellite, or streaming box, plus
a Blu-ray or DVD player and a
soundbar or other audio-only
device
• Programming by popular brand
names for quick and easy setup
• Extensive code library for less
common brands and devices
• Premium design, materials, and
construction for rugged use
INSTALLING BATTERIES
• Insert two AAA batteries (not
included) into the remote. Make
sure that the + and – symbols
match the + and – symbols in the
battery compartment.
Note: To set up your remote, follow the
setup steps below, in order, and STOP
as soon as your remote works correctly.
PROGRAMMING YOUR
REMOTE
There are three ways to set up your
remote:
• Use “Setup method A: Popular
brands” for pre-set popular brands.
• Use “Setup method B: Direct code
entry” if your device’s direct code is
in the code list starting on page 12.
• Use “Setup method C: Code search”
to perform a code search for your
device.
Note: This remote comes pre-set for
Insignia TVs and DVDs and Apple TV
cable/satellite/streaming set-top boxes.
Setup method A: Popular brands
1 Turn on your target device.
2 Press and hold SETUP until your
remote’s LED blinks twice.
3 Press
TELEVISION or
CABLE / SATELLITE /
STREAMING, or
DVD to select the mode you want
to set up. The LED stays lit.
BLURAY/
4 Press either 0 (for cable/satellite/
streaming), 1 (for TVs), or 2 (for
Blu-ray/DVD) to select the device
type you want to set up.
5 Find your device type and brand
in the table below, then press and
hold its number until your device
turns o . Setup for that device is
complete.
Note: If your brand does not appear in
the table below, use “Setup method B:
Direct code entry” or “Setup method C:
Code search.”
Magnavox
CABLE / SATELLITE
/ STREAMING
Cox Communications Philips,
Communications,
Verizon
#TV
1 InsigniaAT&TInsignia
2 LGBel lLG
3 Panasonic Comcast, X nityPanasonic
4 Philips,
5 SamsungDIRECTVPioneer
6 SharpDISH NetworkSamsung
7 SonyFrontier
8 TCLRogersSony
9 ToshibaShawToshiba
0 VIZIOSpec trumYamaha
BLU-RAY/
DVD
Magnavox
Sharp
Setup method B: Direct code
entry
1 Turn on your target device.
2 Press
TELEVISION or
CABLE / SATELLITE /
STREAMING, or
BLURAY/
DVD to select the mode you want
to set up.
3 Press and hold SETUP until your
remote’s LED blinks twice.
4 Enter the rst 5-digit code for your
brand from the code list (see TV
CODE LIST on page 12).
5 Press the
(power) button to test
your device. Release the key when
your device turns o . Setup for that
device is complete.
6 If the device does not turn o ,
repeat steps 2-5 using the next
code for your brand or use “Setup
method C: Code search”.
Setup method C: Code search
1 Turn on your target device.
2 Press and hold SETUP until your
remote’s LED blinks twice.
3 Press
4 Press either 0 (for cable/satellite/
5 While pointing the remote toward
TELEVISION or
CABLE / SATELLITE /
STREAMING, or
DVD to select the mode you want
to set up. The LED stays lit.
streaming), 1 (for TVs), or 2 (for
Blu-ray/DVD) to select the device
type you want to set up.
your target device, press and hold
OK until your device turns o .
Release the key when your device
turns o . Setup for that device is
complete.
BLURAY/
LEARNING FUNCTIONS
FROM ANOTHER REMOTE
You can learn any function from your
original (working) remote control.
Creating a learned function
1 Make sure that your remote is
programmed to the device you
want to control. See “Programming
your remote.”
2 Place your original and new
remotes on a table with their IR
sensors 1-2" apart.
3 With your new remote, press and
hold SETUP until the LED blinks
twice.
4 With your new remote, press 9, 7, 5.
5 With your new remote, press
TELEVISION or
SATELLITE / STREAMING, or
BLURAY/DVD for the device
you want to learn a function from.
6 With your new remote, press the
button you want to add a function to.
The LED blinks continuously.
Note: Functions cannot be assigned to
the setup key or the three device keys.
CABLE /
7 With your original remote, press the
button with the function you want
to teach. The LED blinks twice.
Note: If the LED displays a long blink,
the function wasn’t learned. Start from
step 5 to try again.
8 Repeat steps 5-7 for each button
you want to learn.
9 After you have added all the functions,
press and hold SETUP on your new
remote until its LED blinks twice.
Deleting a learned function
1 Press and hold SETUP until your
remote’s LED blinks twice.
2 Press
TELEVISION or
CABLE / SATELLITE /
STREAMING, or
BLURAY/
DVD for the device you want to
delete a function from.
3 Press 9, 7, 6.
4 Press the button with the learned
function twice. The LED blinks
twice and the button resets to its
original function.
USING YOUR REMOTE
1 Press TELEVISION or
CABLE / SATELLITE /
STREAMING, or
DVD for the device you want to
control.
2 Press the buttons applicable to
that type of device.
BLURAY/
Watch TV mode
Note: To control a soundbar or other
audio device with your remote, see
Adding an audio device.
While watching TV in
CABLE /
SATELLITE / STREAMING mode,
you can:
• Use your remote’s volume and
input buttons to control the TV. The
rest of the buttons will control the
device you’ve added to CABLE /
SATELLITE / STREAMING mode.
(power) once to turn your
• Press
set-top box on or o .
OR
• Press and hold (power) for two
seconds to turn both your set-top
box and your TV on or o .
To turn o watch TV mode:
1 Press and hold SETUP until your
remote’s LED blinks twice.
2 Press
Watch TV mode is turned o and
To turn on watch TV mode after
turning it o :
1 Press and hold SETUP until your
2 Press CABLE / SATELLITE /
Watch TV mode is turned back on
CABLE / SATELLITE /
STREAMING twice. The LED blinks
four times.
your remote will not control your TV.
remote’s LED blinks twice.
STREAMING twice. The LED blinks
twice.
and your remote will control your
TV again.
ADDING AN AUDIO DEVICE
If you listen to sound through
a connected audio device (for
example, a soundbar or audio/video
receiver), you can program your
remote to control it when in
CABLE / SATELLITE /
STREAMING mode:
• Use “Method A: Popular audio
devices” if your audio device is
listed as a popular brand, or
• Use “Method B: Audio device code
entry” to perform a code search for
your device.
Method A: Popular audio devices
1 Turn on your audio device and play
something through its speakers.
2 Press and hold SETUP until your
remote’s LED blinks twice.
3 Press
4 Find your audio device’s brand and
5 While aiming the remote at your
MUTE.
corresponding number in the table
on the next page.
audio device, press and hold your
audio device’s number (from
step 4) until the sound mutes.
Setup is complete and your remote
controls your audio device’s volume
while using a cable, satellite, or
streaming device.
#AUDIO#AUDIO
1 Bose6 Philips
2 Denon7 Pioneer
3 LG8 Samsung
4 Onkyo9 Sony
5 Panasonic0 Yamaha
Method B: Audio device code
entry
1 Turn on your audio device and play
something through its speakers.
2 Press and hold SETUP until your
remote’s LED blinks twice.
3 Press
MUTE.
4 Find your audio device’s brand in
the code list (see AUDIO CODE LIST
on page 57), then use your remote
to enter the rst 4-digit code for
your brand from the code list.
5 Press
MUTE to test your audio
device. If the sound mutes, setup
is complete and your remote
controls your audio device’s volume
while using a cable, satellite, or
streaming device.
6 If the sound doesn’t mute, repeat
steps 2-5 using the next code for
your brand.
LOCKING AND UNLOCKING
VOLUME CONTROLS
By default, the VOL
(volume up/down) and
buttons control your TV. You can
lock this setting so the remote
always controls your cable/satellite/
streaming device, or unlock it so
each device controls its own volume.
Locking volume controls to one
device
1 Press and hold SETUP until your
remote’s LED blinks twice.
2 Press 9, 9, 3.
3 Press
TELEVISION or
CABLE / SATELLITE /
STREAMING, or
DVD to lock volume controls to
that device. The LED blinks twice.
/
(mute)
BLURAY/
Unlocking volume controls
1 Press and hold SETUP until your
remote’s LED blinks twice.
2 Press 9, 9, 3, then press VOL
(volume up).
LOCKING AND UNLOCKING
CHANNEL CONTROLS
Locking channel controls to one
device
1 Press and hold SETUP until your
remote’s LED blinks twice.
2 Press 9, 7, 3, then press CH +.
3 Press
Unlocking channel controls
1 Press and hold SETUP until your
2 Press 9, 7, 3, then press CH -.
TELEVISION or
CABLE / SATELLITE /
STREAMING, or
DVD to lock channel controls to
that device. The LED blinks twice.
remote’s LED blinks twice.
BLURAY/
RESETTING REMOTE TO
FACTORY DEFAULTS
1 Press and hold SETUP until your
remote’s LED blinks twice.
2 Press 9, 7, 7.
REMOTE OVERVIEW
#ITEMDESCRIPTION
1SETUPPrograms the remote
2TELEVISIONPress to control
3NumbersEnter channel
4Delimiter
(-)
5HomeOpens the home
6MENUDisplays the main
7OKCon rms a selection
8INFODisplays info on the
9LASTReturn to the last
10 Volume up/
down
11 MUTEMutes the sound
12 VODPress to order
13 Red, green,
yellow,
blue
14 Playback
controls
15 RECStarts or stops
16 PowerTurns devices on
17 BLURAY/
DVD
18 CABLE /
SATELLITE /
STREAMING
19 ENTERCon rms a menu
20 GUIDEDisplays the program
21 EXITExits the current
22 INPUTSelect input/source
23 Channel up/
down
24 APPSOpens a smart
25 LISTDisplays a list of
your TV
numbers
Enters a digital
sub-channel number
(for example 4.1)
menu
menu
current program
channel
Raises or lowers the
volume
video-on-demand or
pay-per-view
Shortcut keys in some
menus
Control devices
connected to your TV
recording
and o
Press to control a
Blu-ray and DVD
Press to control a
cable / satellite /
streaming device
selection
guide
menu
to be displayed (for
example HDMI 1)
Changes the channel
device’s app menu
recorded shows
TROUBLESHOOTING
PROBLEMSOLUTION
The LED does
not turn on
when a key is
pressed.
• Replace the
batteries.
The LED turns
on, but the
remote does
not control my
device.
I have tried all
of the codes
for my device’s
brand, but
none of them
work.
After
programming,
some of my
remote’s
functions
don’t work
• Make sure that
your remote is
programmed to
your device.
• Make sure that
your remote
is set to the
correct mode
(TELEVISION,
BLURAY/DVD,
or CABLE /
SATELLITE /
STREAMING).
• Use Setup
Method C: Code
Search.
• If you still have
your original
(working)
remote, you
can teach your
new remote its
functions. S ee
Learning
functions from
another remote.
ONEYEAR LIMITED
WARRANTY
Visit www.insigniaproducts.com for
details.
CONTACT INSIGNIA:
For customer service, call
1-877-467-4289 (U.S. and Canada)
or
01-800-926-3000 (Mexico)
www.insigniaproducts.com