Insignia NS-NAV01 GPS User Manual

Quick Setup Guide

NS-NAV01 GPS

Congratulations on your purchase of a high-quality

Insignia product. Your GPS is designed for reliable and

trouble-free performance. Use this guide for initial setup.

See your User Guide for more information.

Package contents

• 4.3" GPS

• DC power adapter

• Mounting bracket

• Mounting cradle

• SD memory card

• User Guide

• Quick Setup Guide

Setting up your GPS

Charging the battery

Your portable GPS comes with a built-in rechargeable battery. Fully charge the battery before using the GPS for the rst time. Charging time is normally about three hours. A fully charged battery delivers about two hours of use. See “Connecting power to your GPS” below.

Features

Top and side panels

Bottom panel

Mounting

slot

Reset

hole

Mounting

slot

Power button

Card slot

USB charging

port

Actual product may vary from image shown.

Mounting your GPS in a car

WARNING: The assembly must not be mounted so that it impairs the driver’s view of the road. Make sure that your car’s airbags are not obstructed by the GPS.

Use the supplied mounting bracket and cradle to mount your GPS in a vehicle.

1 Slide the mount cradle onto the end of the mounting bracket to attach it. 2 Set the bottom edge of your GPS onto the mount cradle, then push the GPS

into the tab (1) at the top of the mount cradle. To remove the GPS, lift the tab (1) at the top of the mount cradle and pull the GPS forward. 3 Lift the suction cup lever (2) and then press the suction cup to the windshield. 4 Press the suction cup lever toward the windshield to attach the bracket to the windshield.

5 Rotate the knob to adjust the assembly to the proper position.

Connecting power to your GPS

Connecting DC power

CAUTION: Disconnect the GPS from the DC power adapter when starting the vehicle.

• Connect the DC power adapter plug to the GPS’s USB port, then plug the other end to the vehicle’s 12-24V DC accessory socket (cigarette lighter socket).

cigarette lighter

socket

Getting started

Using your GPS

1 Turn on the GPS. When you turn it on for the rst time, the Time zone screen opens. 2 Touch the time zone where you are currently located, then touch OK. A splash screen appears for a few seconds, then the safety Warning appears.

3 To continue on to the device features, touch I Agree at the bottom right of the screen. The

Home screen appears.

Using the Home screen

From the Home screen, you can see where you are, nd a route to a place of interest, or change settings.

• To see where you are, touch Map

- OR To nd a route:

1 Touch Go to. The Main menu opens. 2 Touch Address. A keypad opens. 3 Enter an address. The GPS automatically calculates

the best route choice to direct you to that address. See Creating a route to an address in your User Guide for more detailed instructions.

• To change settings, touch the settings icon at the top right corner of the screen. To learn more about these settings, see Setting up your GPS device preferences in your User Guide.

Using the Main menu

• Go home — touch to calculate a route to your home address from wherever you are. To learn more about setting your home address, see your User Guide.

• Address — touch to navigate to an address or intersection near the address.

• Search — touch to enter locations or points of interest for directions to restaurants, theaters, public services, and more.

• Favorites — touch to get directions from your location to places you have saved as Favorites.

• Recent — touch to navigate to your most recent destinations without having to enter them again.

• Browse — touch to search categories, including gas , restaurants, and other points of interest.

Creating a route to an address

1 Touch Go to on the Home screen. The Main menu opens. 2 Touch Address on the Main menu. The city in which you are

located is displayed, along with cities to which you have recently navigated. If this is the rst time you are using the GPS, only the name of the city of your current GPS location is shown.

3 Touch the name of the city to which you want to navigate. The Enter House number keypad opens.

- OR To go to a city that is not listed, touch Other city to open the Enter City name keypad, then enter the name of the city you want and touch Next. The Enter House number keypad opens.

4 Enter the house number, then touch Next. The Enter Street Name keypad opens.

5 Enter the name of the street. After entering a few characters, the GPS displays a list of street names that include those characters.

6 Touch the street name you want. If the street name is not on the list, touch the back arrow and re-enter the street name, then touch Next. The address card for your destination opens.

7 Touch Go. The GPS calculates your route. When the calculation is complete, the route is highlighted on the map view and the voice prompts begin.

• To view the turn-by-turn maneuvers, touch the distance to next maneuver button at the top left of the map view.

• To zoom in, touch the + button on the right side of the screen.

• To zoom out, touch the - button on the side of the screen.

• To pan across the map and view portions that are beyond the limits of the screen, touch the map anddrag your nger. When you do this, the GPS displays “Pan Mode” at the top of the screen.

• To return to your last known location from Pan Mode, touch center car at the bottom of the screen.

• To return to the Map view, touch the back arrow at the bottom left of the screen.

© 2009 Best Buy Enterprise Services, Inc. All rights reserved. INSIGNIA is a trademark of Best Buy Enterprise Services, Inc. Registered in some countries. All other products and brand names are trademarks of their respective owners.

ENGLISH 09-0446