Insignia NS-MWF-2, NS-LT600B-2, NS-DA2920, NS-DA2920-2, NS-DA2903 Quick Setup Guide

						Quick Setup Guide
			Refrigerator Filter | NS-MWF-2/NS-LT600B-2/NS-DA2920/NS-DA2920-2/NS-DA2903/NS-DA2903-2
				4	After installing, run about two to three gallons of water through your	NS-LT600B-2 (LG and Kenmore)
	Congratulations on your purchase of one of the highest				refrigerator’s water dispenser to remove air and loose carbon pieces. The	1 Remove the old filter by rotating a half turn
	performing water filters on the market today. Insignia filters use			5	water may be cloudy and sputter until the air is removed.	counterclockwise, then pull it out. The water
	a high-grade coconut carbon that has 50% more micro-pores				We apply a safe, NSF approved, food grade silicone lubricant to our filter	automatically turns off.
	than standard carbon. They also use fewer high-compression				connectors (jelly like substance).	2 If you have a Kenmore refrigerator, check if there is
	binders, giving you the best water filtration possible.					a plastic or metal cap that covers the top of the old
						filter. If there is, pull off the cap and attach it to
	Package contents			NS-DA2903 or NS-DA2903-2 (Samsung)		your new filter. If there is not, continue to step 3.
				1	Remove the old filter by rotating it a quarter turn	3 Align the top of your new filter with the receiver,
	• Refrigerator filter(s) (1 or 2 pack)				counterclockwise, then pull it straight down.	then push it in until it stops.
	• Quick Setup Guide				The water automatically turns off.	4 Rotate the filter a half turn clockwise to secure the
				2	Align the top of your new filter with the receiver,	filter, then twist a little more to prevent leaks.
					then push it up until it stops.
				3	Rotate the filter a quarter turn clockwise to	NS-DA2920 or NS-DA2920-2 (Samsung)
	General installation guidelines				secure the filter.
						1 Remove the old filter by rotating it a 1/4 turn
	1 YOU MUST SOAK your new filter in water for 15 minutes prior to
						counterclockwise, then pull it out.
	installing it in your refrigerator. This is needed to remove air from
						2 Align the top of your new filter with the receiver,
	the carbon block.
				NS-MWF-2 (GE, Hotpoint, Amana, and Kenmore)		then push it up until it stops.
	2 It is normal for black carbon fines (particles) to appear on the outside
				1	Remove the old filter by rotating it a half turn	3 Rotate the filter a 1/4 turn clockwise to secure the
	of your filter. This happens when the filter is jarred in shipping, it is
					counterclockwise, then pull it straight down. The	filter.
	safe, simply wipe it off.
					water automatically turns off.
	3 Connections on our filters are larger in size to prevent leakage. This
				2	If you have a Kenmore refrigerator, check if there
	might require more hand leverage to install.
					is a plastic or metal cap that covers the top of the	Before using your filter
		Installation:
		*PUSH AND TURN HARD			old filter. If there is, pull off the cap and attach it to	If your refrigerator has a change filter indicator, reset it. See“Resetting your
		To remove turn counter-clockwise			your new filter. If there is not, continue to step 3.
				3		filter indicator”for instructions.
		To install turn clockwise			Align the top of your new filter with the receiver,
		Do not remove the O-ring			then push it up until it stops.
		Filter receivers are designed to be flexible.		4	Rotate the filter a half turn clockwise to secure
		Don’t worry, they won’t break!			the filter, then twist a little more to prevent leaks.

Before using your new product, please read these instructions to prevent any damage.