Illustrations in this guide are provided for
reference only and may differ from actual
product appearance. Product design and
specification may be changed without notice.
Before using your new product, please read these instructions to prevent any damage.
Manufacturers, retailers and the rest of the consumer electronics industry are
committed to making home entertainment safe and enjoyable.
•
As you enjoy your television, please note that all televisions - new and old - must be
supported on proper stands or installed according to the manufacturer's
recommendations. Televisions that are inappropriately situated on dressers, bookcases,
shelves, desks, speakers, chests, carts, etc., may fall over, resulting in injury.
TUNE IN TO SAFETY
•
ALWAYS follow the manufacturer’s recommendations for the safe installation of your
television.
•
ALWAYS read and follow all instructions for proper use of your television.
•
NEVER allow children to climb on or play on the television or the furniture on which the
television is placed.
•
NEVER place the television on furniture that can easily be used as steps, such as a chest
of drawers.
•
ALWAYS install the television where it cannot be pushed, pulled over or knocked down.
•
ALWAYS route cords and cables connected to the television so that they cannot be
tripped over, pulled or grabbed.
WALL OR CEILING MOUNT YOUR TELEVISION
•
ALWAYS contact your retailer about professional installation if you have any doubts
about your ability to safely mount your television.
•
ALWAYS use a mount that has been recommended by the television manufacturer and
has a safety certification by an independent laboratory (such as UL, CSA, ETL).
•
ALWAYS follow all instructions supplied by the television and mount manufacturers.
•
ALWAYS make sure that the wall or ceiling where you are mounting the television is
appropriate. Some mounts are not designed to be mounted to walls and ceilings with
steel studs or cinder block construction. If you are unsure, contact a professional
installer.
•
Televisions can be heavy. A minimum of two people is required for a wall or ceiling
mount installation.
MOVING AN OLDER TELEVISION TO A NEW PLACE IN YOUR
HOME
•
Many new television buyers move their older CRT televisions into a secondary room
after the purchase of a flat-panel television. Special care should be made in the
placement of older CRT televisions.
•
ALWAYS place your older CRT television on furniture that is sturdy and appropriate for
its size and weight.
•
NEVER place your older CRT television on a dresser where children may be tempted to
use the drawers to climb.
•
ALWAYS make sure your older CRT television does not hang over the edge of your
furniture.
CE.org/safety
1
Important Safety Instructions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates that
dangerous voltage
constituting a risk of electric
shock is present within your TV.
This label is located on the
back of your TV.
This symbol indicates that
there are important operating
and maintenance instructions
in the literature accompanying
your TV.
This symbol indicates that this
product incorporates double
insulation between the
hazardous main voltage and
user accessible parts. When
servicing, use only identical
replacement parts.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
8 Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the
cart/apparatus combination to
avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
15 The wall plug is the disconnecting device. The plug
must remain readily operable.
16 Remote control batteries should not be exposed
to excessive heat such as sunshine, fire, or the like.
17 The apparatus should not be exposed to dripping
or splashing, and no objects filled with liquids,
such as vases, should be placed on the apparatus.
18 Your TV has four VESA mounting holes on the
back. If you attach a wall-mount bracket or TV
stand to the back of your TV, the bracket or stand must be securely attached using all four holes.
If you do not use all four mounting holes, your TV
may fall and cause property damage or personal
injury. See the documentation that came with
your wall mount or TV stand for complete
mounting instructions.
WARNIN G
Electric shock hazard
To reduce the risk of fire or electric shock, do not
remove any cover or expose the device to rain or
moisture. No user-serviceable parts are inside. Refer
servicing to qualified service technicians.
Lightning
For added protection for your device receiver during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the
power outlet and disconnect any antenna or cable
system. This helps prevent property damage and
personal injury from lightning and power line surges.
Power lines
An outside antenna system should not be located in
the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside
antenna system, take extreme care to keep from
touching such power lines or circuits as contact with
them might be fatal.
2
www.insigniaproducts.com
NS-40DR420NA16/NS-48DR420NA16
Handling the LCD panel
• Your TV’s screen is made of glass. Do not drop your
TV or hit, jolt, or press hard against the LCD panel. If
the screen breaks, be careful of broken glass.
• If the LCD panel is broken, make absolutely sure that
you do not touch the liquid in the panel. This may
cause skin inflammation.
• If the liquid gets in your mouth, immediately gargle,
rinse, and consult with your doctor. Also, if the liquid
gets in your eyes or touches your skin, consult with
your doctor after rinsing for at least 15 minutes or
longer in clean water.
Replacement parts
When replacement parts are required, make sure that
the service technician uses replacement parts
specified by the manufacturer that have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock,
personal injury, or other hazards.
Safety check
After completing any service or repair to this device,
ask the service technician to perform routine safety
checks to determine that your TV is in correct
operating condition.
Power source
Operate your TV only from the type of power source
indicated on the marking label. If you are not sure of
the type of power supplied to your home, consult an
electrician or your local power company.
Servicing
These servicing instructions are for use by qualified
service personnel only. To reduce the risk of electric
shock, do not perform any servicing other than that
contained in the operating instructions unless you are
qualified to do so.
CAUTION
Damage requiring service
Unplug this TV from the power outlet and refer
servicing to qualified service personnel under the
following conditions:
• When the power supply cord or plug is damaged or
frayed.
• If liquid has been spilled or objects have fallen into
your TV.
• If your TV has been exposed to rain or water.
• If your TV does not operate normally by following
the operating instructions. Adjust only those
controls covered by the operating instructions
because incorrect adjustment of other controls may
result in damage and will often require extensive
work by a qualified technician to restore your TV to
its normal operation.
• If your TV has been dropped or damaged in any
way.
• When your TV exhibits a distinct change in
performance.
Outdoor antenna grounding
If an outside antenna or cable system is connected to
your TV, make sure that the antenna or cable system is
grounded to provide some protection against voltage
surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA No. 70, provides
information with respect to correct grounding of the
mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of
grounding conductors, location of the
antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding
electrode.
1 Antenna lead-in wire
2
Grounding clamp
Antenna discharge
3
unit
Grounding
4
conductors
5 Ground clamps
Power service
grounding elec trode
6
system
Electric service
7
equipment
Note to CATV system installer
Article 820 of the National Electrical Code, ANSI/NFPA
No. 40 provides guidance for correct grounding.
Specifically, it states that the cable ground must be
connected to the grounding system of the building as
close to the point of cable entry as practical.
Condensation
Moisture will form on the TV if the TV is brought from
cool surroundings into a warm room or if the
temperature of the room rises suddenly. When this
happens, the TV's performance may be impaired. To
prevent this, let the TV stand in its new surroundings
for about an hour before switching it on, or make sure
that the room temperature rises gradually.
Condensation may also form during the summer if
the TV is exposed to the breeze from an air
conditioner. In such cases, change the location of the
TV.
Mobile telephone warning
To avoid interference with your TV picture and sound,
operating problems, or even damage, keep your
cordless and cellular telephones away from the TV.
www.insigniaproducts.com
3
End of life directives
Your TV may contain materials that are regulated for
environmental reasons. Your TV also contains
materials that can be recycled and reused. To help
protect the environment, contact your local
authorities for information about disposal or recycling
and about finding a recycler in your area before you
dispose of your TV.
Non-active pixels
The LCD panel contains almost 3 million thin film
transistors, which provide exceptionally sharp video
quality. Occasionally, a few non-active pixels may
appear on the screen as a fixed blue, green, or red
point. These non-active pixels do not adversely affect
the performance of your TV, and are not considered
defects.
4
www.insigniaproducts.com
NS-40DR420NA16/NS-48DR420NA16
40"/48" 1080p, 60Hz, LED Insignia Roku TV
Welcome
Congratulations on the purchase of your new TV! Discover the joy of endless entertainment. After it's set up, you'll be
able to access a world of streaming content channels that may include Netflix, YouTube, Crackle, CNET and literally
thousands more.
Important
Your TV receives automatic updates from time to time, enabling new
content and features. This User Guide explains how to use your TV after it
has been updated to version 7.0. If your TV has not yet been updated to
version 7.0, some of the information in this User Guide does not apply. To
determine the current version of your Roku TV, go to
Settings > System > About after you complete Guided Setup.
The new standard in Smart TVs
Welcome to TV like you've most likely never seen before—a home screen that you can personalize with your favorite
devices and streaming channels. Choose from hundreds of thousands of streaming movies and TV episodes, plus music,
sports, kids, family, international and much more. You should never run out of things to watch.
Note
A paid subscription or other payments may be required for some channels.
Channel availability is subject to change and varies by country. Not all
content is available in countries or regions where Roku products are sold.
Get the most out of your new TV
Follow these simple steps to get the most out of your new TV.
1 Connect to the Internet
• It's simple, it's easy, and it will unlock a world of entertainment. All you need is a wireless network. There are
hundreds of free streaming channels, subscriptions services like Netflix and Spotify, convenient ways to rent or buy
a favorite film or show with Google Play and Cineplex and more.
2 Pick your favorite streaming channels
• Find the entertainment you love. From the latest blockbuster movies to your favorite TV shows, with tons of live
sports, a broad selection of music streaming channels, popular programming in a dozen international languages,
24x7 live news and so much more, your new TV has your sweet spot. A paid subscription or other payments may
be required for some channels.
3 Personalize your home screen
• Put your favorite broadcast TV, streaming channels, gaming console and other devices front-and-center on the
home screen. No more flipping through inputs or wading through complicated menus. You can even personalize
the names of each input and move tiles around so your most-often used devices and streaming channels are only
a click away.
4 Search for your favorite movie, TV show, actor, or director
• Once you’re connected to the internet, you can easily search across top streaming channels by movie or TV show
title, actor or director—all from one place. Search results are organized by price so you can always see the best
priced option. A paid subscription or other payments may be required for some channels.
5 Send your personal media to the big screen
• Send personal photos, videos, and music from your compatible smartphone or tablet to the TV screen in just a few
taps. Plus, with Netflix and YouTube apps, send movies, shows, sport highlights, and more directly to your TV.
Note
The Roku app for Microsoft Windows devices does not cast videos.
www.insigniaproducts.com
5
40"/48" 1080p, 60Hz, LED Insignia Roku TV
6 Follow movies coming soon
• Use My Feed to choose from and follow a list of upcoming movies, and then watch for alerts each time one of your
followed movies becomes available or changes price.
Note
My Feed is not available in the Roku App for Windows devices in the United
States or Canada.
7 Take charge with a smartphone or tablet
• Control your TV with the included remote or from your compatible smartphone or a tablet with the free mobile
app for iOS, Android, and Windows devices. Browse channels, view My Feed, and even search with voice via the
free mobile app.
Note
Voice search and My Feed are not available in the Roku app for Windows
devices.
• Mirror your compatible smartphone or tablet on your TV. Share videos, photos, web pages, and more from
compatible devices.
• Use your compatible smartphone or tablet to connect your TV to the types of networks found in hotels and
college dorms, where you may have to agree to terms, enter codes, or provide identifying information.
Note
Using your Roku TV on a restricted public network requires wireless
availability and use of your network-connected smartphone, tablet, or
computer to authenticate access to your account. Your TV must already be
linked to your Roku account and activated. Also, you must use your Roku TV
remote control, because the Remote feature of the Roku mobile app does
not work on restricted public networks. Streaming content might be limited
due to your geographic location or because of restrictions imposed by the
wireless network host.
Many features work with top mobile devices. Please see http://support.roku.com for device compatibility information.
Let's get started.
6
www.insigniaproducts.com
NS-40DR420NA16/NS-48DR420NA16
Installing the stands or wall-mount bracket
• If you want to place your TV on a table or in an entertainment center, go to Installing the stands.
• If you want to mount your TV on a wall, go to Installing a wall-mount bracket.
Notes
• If you plan to wall-mount your TV, do not install the stands.
• Store the stands and stand screws in case you decide to use the stands
in the future.
Installing the stands
1 Carefully place your TV face-down on a cushioned, clean surface to protect the screen.
www.insigniaproducts.com
7
40"/48" 1080p, 60Hz, LED Insignia Roku TV
2 Align the TV stands with the screw holes on the bottom of the TV, then secure the stands to the TV with the four
provided screws.
ModelScrew typeScrew length# of screws
40-in.ST420 mm4
48-in.M515 mm4
8
www.insigniaproducts.com
NS-40DR420NA16/NS-48DR420NA16
Installing a wall-mount bracket
Warnings
• Your TV has four VESA mounting holes on the back. If you attach a
wall-mount bracket to the back of your TV, the bracket must be securely attached, using all four holes. If you do not use all four
mounting holes, your TV may fall and cause property damage or
personal injury. See the documentation that came with your wall mount
for complete mounting instructions.
• Your TV is intended to be supported by a UL Listed wall mount bracket
with suitable weight/load. (See Miscellaneous on page 82.)
1 Carefully place your TV face-down on a cushioned, clean surface to protect the screen.
2 If the TV stands are installed, remove the four screws that secure the stands to your TV.
www.insigniaproducts.com
9
40"/48" 1080p, 60Hz, LED Insignia Roku TV
3 Attach the wall-mount bracket to your TV using the mounting holes on the back of your TV. See the instructions that
came with the wall-mount bracket for information about how to correctly hang your TV.
Notes
• The length of the wall-mount screws vary depending on the wall-mount
bracket you purchased. See the instructions that came with the
wall-mount bracket for screw lengths.
• The mounting holes on the back of your TV take type M6 screws.
15.7 in. (400 mm)
7.9 in. (200 mm)
10
www.insigniaproducts.com
NS-40DR420NA16/NS-48DR420NA16
TV components
Your TV has built-in controls for adjusting basic
settings and several sets of jacks for connecting
devices to your TV.
This section contains information about:
•Package contents
•Front features
• Buttons
•Side jacks
•Back jacks
• Remote control
Package contents
• 40" or 48" LED TV
• Remote control and batteries (2 AAA)
•TV stands (2)
•Screws (4)
•Power cord
• Quick Setup Guide
• Important Information
Front features
Buttons
The controls on your TV enable you to perform simple
functions, but are not a substitute for the remote
control. Your TV has seven buttons on the bottom
edge of the screen. From left to right, they perform
the following functions:
#ItemPress to...
Select among the configured TV
inputs. Each press moves down
one item. Also, while the Input
1 INPUT
panel is visible, the CH+ and CH–
buttons move the highlight up
and down. Pausing for a few
moments selects the highlighted
input.
#ItemDescription
Remote control
1
sensor
Status indicatorSee Status light on page 46.
2
Receives signals from the remote
control. Do not block.
2
MUTEMute or unmute the sound.
3 VOL+/VOL–
CH+/CH–
4
5
(
power)
Press to increase or decrease the
volume.
Go to the next or previous
channel in the channel list. For
more information, see Watching
broadcast TV channels on
page 46.
OR
Move the highlighted item up
down in the current menu.
Press to turn your TV on or off
(standby mode).
War ning: When your TV is off,
power still flows through it. To
completely disconnect power,
unplug the power cord.
www.insigniaproducts.com
11
40"/48" 1080p, 60Hz, LED Insignia Roku TV
Side jacks
#ItemDescription
Connect an HDMI device to this
jack. For more information, see
HDMI (best) on pages 17, 21,or 23
or Connecting a computer on
5 HDMI1/ARC
6
HDMI2
7 HDMI3
8
RESET
page 25.
OR
Connect an ARC-enabled home
theater receiver to this jack. For
more information, see ARC jack on
page 29.
Connect an HDMI device to this
jack. For more information, see
HDMI (best) on pages 17, 21, or 23
or Connecting a computer on
page 25.
Connect an HDMI device to this
jack. For more information, see
HDMI (best) on pages 17, 21, or 23
or Connecting a computer on
page 25.
Press and hold reset for 15 seconds
for a factory reset. See What if I can’t
access the Factory Reset option? on
page 70.
#ItemDescription
Connect a digital sound bar,
speaker system, or home theater
DIGITAL OUTPUT
1
(OPTICAL)
ANT/CABLE IN
2
3 USB 2.0
4
system to this jack to listen to TV
audio through external speakers.
For more information, see Digital
optical audio jack on page 28.
Connect an antenna or cable TV to
this jack. For more information, see
Coaxial (good) on page 19 or
Connecting an antenna or cable TV
(no box) on page 20.
Connect a USB flash drive to this
jack to view compatible photos and
video and listen to music files. For
more information, see Connecting a
USB flash drive on page 26 and
Playing content from USB storage
devices on page 48.
Connect headphones to this jack.
See Connecting headphones on
page 27.
12
www.insigniaproducts.com
NS-40DR420NA16/NS-48DR420NA16
Back jacks
# ItemDescription
Connect the video for an AV
device to the VIDEO jack. For
1 VIDEO
AUDIO L and R
2
more information, see AV
(composite video) (good) on
page 18, 22, or 24.
Connect the audio for an AV
device to these jacks. For more
information, see AV (composite
video) (good) on page 18, 22,
or 24.
www.insigniaproducts.com
13
40"/48" 1080p, 60Hz, LED Insignia Roku TV
Remote control
#ButtonDescription
(power)
1
(back)
2
If your TV is in Standby mode, turns power on.
If your TV is on, puts TV in Standby mode.
The action depends on what you are doing with your TV:
Menu—Goes ba ck to previous menu or screen.
Home screen ti le—Moves highlight back to the Home
menu option.
Watching Antenna TV or a TV input—Returns to the
screen from which the input was selected.
Playing streaming content—Stops playing stream and
returns to the previous menu or screen.
Browsing streaming content—G oes to the previous
level in the content tree.
#ButtonDescription
—Moves the highlight up one item.
—Moves the highlight down one item.
—Moves the highlight left, if possible (if a < hint
appears).
When watching TV, displays your channel list.
When playing most streaming videos, skips backward in the
3
and OK
4
(Game Mode )
(sleep)
5
(rewind)
6
(play/pause)
7
(home)Immediately returns to the Home screen menu.
8
(options)
9
video.
—Moves the highlight to the right, if possible (if a > hint
appears).
When watching TV with the channel list displayed, dismisses
the channel list.
When playing most streaming videos, skips forward in the
video.
OK—Selects the highlighted option.
When watching TV, this button displays information for the
current TV program.
First press displays a banner showing the current Game
mode, if applicable, or Not available at this time.
Subsequent presses toggle Game mode. When On, your TV
performs less image processing and has less input lag. When
Off, your TV performs more image processing and has more
input lag, which is less desirable for action games. Note:
Available only for HDMI and AV inputs.
First press displays a banner showing the remaining sleep
time, if any, or Sleep timer is off. Subsequent presses cycle
among the preset sleep time intervals: 30 minutes, 1hour,
1.5 hours, 2hours, and 3hours. After setting the Sleep
timer, the timer remains in effect regardless of what you are
watching.
When playing streaming video that supports this feature:
• First press rewinds at 1x speed.
• Second press rewinds at 2x speed.
• Third press rewinds at 3x speed.
• Subsequent presses cycle through 1x, 2x, and 3x
rewin d speed.
When playing streaming audio, jumps to the previous
track/selection.
When any menu, tile, or channel in the channel list is
highlighted, jumps up one page.
When using a virtual keyboard, jumps to the character at the
top of the current column.
When playing streaming content, alternately pauses and
plays the content.
Displays an Options menu, but only when the Options
hint in the upper-right corner of the screen is not dimmed.
The menu you see varies depending on what you are doing
with your TV.
Also, in most cases, pressing while video is playing
displays an Options menu over part of the screen where you
can adjust various picture and sound settings.
14
www.insigniaproducts.com
NS-40DR420NA16/NS-48DR420NA16
#ButtonDescription
When playing streaming video that supports this feature:
• First press fast forwards at 1x speed.
• Second press fast for wards at 2x speed.
• Third press fast forwards at 3x speed.
• Subsequent presses cycle through 1x, 2x, and 3x
10
FEATURED CHANNEL
11
SHORTCUT
fast forward speed.
When playing streaming audio, jumps to the next
track/selection.
When any menu, tile, or channel in the channel list is
highlighted, jumps down one page.
When using a virtual keyboard, jumps to t he character at the
bottom of the current column.
Dedicated buttons show the logo of a featured streaming
content provider. Pressing a button turns your TV on (if your
TV is not already on), and if your TV is operating and is
connected to the Internet, performs one of the following
actions:
• D isplays the stream ing channel's main page if you
have already added the channel to your Home
screen.
• Displays the streaming channel's sign-up page if
you have not already added the channel so that you
can agree to any terms and fees for the service.
#ButtonDescription
Turns volume up one setting with each press. Press and hold
to turn volume up rapidly. A volume indicator shows the
12
13
14
(volume up)
(volume down)
volume level while you are adjusting the volume and for a
few seconds afterward.
Note: If your TV is m uted, pressing unmute s the sound.
Turns volume down one setting with each press. Press and
hold to turn volume down rapidly. A volume indicator shows
the volume level while you are adjusting the volume and for
a few seconds afterward.
Note: If you r TV is muted, pressi ng does not unmute the
sound.
Mutes and unmutes the TV sound. A volume indicator shows
the current volume level and a mute icon when you press
and for a few seconds afterward. If Clos ed captioning is set
to When Mute, captions are displayed while your TV is
muted.
www.insigniaproducts.com
15
40"/48" 1080p, 60Hz, LED Insignia Roku TV
What connection should I
use?
Your TV has several connection types for connecting
devices to your TV.
For the best video quality, you should connect a
device to the best available connection.
Use the following tables to identify cables:
Video
quality
Best (use this
if your devices
have HDMI)
Good
Connection
type and
jack
HDMI
video/audio
AV (composite
video) (requires
an audio
connection)
Cable connector
Connection
type and
jack
Digital optical
audio output
Analog audio
input
3.5mm analog
audio output
Cable connector
Good
Coaxial
video/audio
Cautions
• Check the jacks for position and type before
making any connections.
• Loose connections can cause poor audio or
video quality. Make sure that all connections
are tight and secure.
• The external audio/video devices shown may
be different from your devices. If you have
questions, refer to the documentation that
came with your devices.
• Always turn off your TV when connecting
external devices.
16
www.insigniaproducts.com
NS-40DR420NA16/NS-48DR420NA16
Connecting a cable or satellite box
Many cable or satellite TV boxes have more than one connection type. To get the best video, you should use the best
connection type available. For more information, see What connection should I use? on page 16.
You can connect your cable or satellite box using:
•HDMI (best)
• AV (composite video) (good)
• Coaxial (good)
HDMI (best)
Cable or
satellite box
On your TV
HDMI cable
connector
HDMI jack
HDMI cable
Side of TV
1 Make sure that your TV’s power cord is unplugged and all connected devices are turned off.
2 Connect the incoming cable from the cable wall jack to the cable-in jack on the cable or satellite box.
3 Connect an HDMI cable (not provided) to an HDMI jack on the side of your TV and to the HDMI OUT jack on the
cable or satellite box.
4 Plug your TV’s power cord into a power outlet, turn on your TV, then turn on the cable or satellite box.
5 On the Home screen, press or to highlight the HDMI 1, HDMI 2, or HDMI 3 tile, then press OK.
Cable
wall jack
Note
An HDMI cable carries both audio and video. You do not need to use any
audio cables.
www.insigniaproducts.com
17
AV (composite video) (good)
Notes
Cables are often color-coded to match color-coded jacks.
On your TV
40"/48" 1080p, 60Hz, LED Insignia Roku TV
Cable
wall jack
AV c able
connector
AV j ack
1 Make sure that your TV’s power cord is unplugged and all connected devices are turned off.
2 Connect the incoming cable from the cable wall jack to the cable-in jack on the cable or satellite box.
3 Connect an AV cable (not provided) to the VIDEO jack and AUDIO L and R jacks on the back of your TV and to the AV
and audio out jacks on the cable or satellite box.
4 Plug your TV’s power cord into a power outlet, turn on your TV, then turn on the cable or satellite box.
5 On the Home screen, press or to highlight the AV tile, then press OK.
Audio cable
connectors
Cable or
satellite box
Analog
audio jacks
Note
When you connect the audio using the AUDIO L and R jacks, the audio
output is analog.
AV c able
Back of TV
18
www.insigniaproducts.com
NS-40DR420NA16/NS-48DR420NA16
Coaxial (good)
Cable or
satellite box
On your TV
Side of TV
Coaxial cable
connector
ANT/CABLE IN
jack
1 Make sure that your TV’s power cord is unplugged and all connected devices are turned off.
2 Connect the incoming cable from the cable wall jack to the cable-in jack on the cable or satellite box.
3 Connect a coaxial cable (not provided) to the ANT/CABLE IN jack on the side of your TV and to the coaxial out jack
on the cable or satellite box.
4 Plug your TV’s power cord into a power outlet, turn on your TV, then turn on the cable or satellite box.
5 Set up the TV tuner to watch broadcast TV. See Setting up Antenna TV on page 42.
6 On the Home screen, press or to highlight the Antenna TV tile, then press OK.
Coaxial cable
Cable
wall jack
Notes
• Use a coaxial cable to eliminate interference and noise from radio
waves.
• Do not bundle the coaxial cable with the power cord or other cables.
www.insigniaproducts.com
19
40"/48" 1080p, 60Hz, LED Insignia Roku TV
Connecting an antenna or cable TV (no box)
Antenna or cable TV
(no box)
On your TV
Coaxial cable
connector
Side of TV
ANT/CABLE IN
jack
1 Make sure that your TV’s power cord is unplugged and all connected devices are turned off.
2 Connect a coaxial cable (not provided) to the ANT/CABLE IN jack on the side of your TV and to the antenna or cable
TV wall jack.
3 Plug your TV’s power cord into a power outlet, then turn on your TV.
4 On the Home menu, press or the highlight the tile for Antenna TV, then press OK.
5 Set up the TV tuner to watch broadcast TV. See Setting up Antenna TV on page 42.
6 On the Home screen, press or to highlight the Antenna TV tile, then press OK.
Notes
• Use a coaxial cable to eliminate interference and noise from radio
• Do not bundle the coaxial cable with the power cord or other cables.
• If the antenna is not installed correctly, contact qualified service
• If the signal level for a channel is weak, the picture may be distorted.
• If the picture quality is good on some channels and poor on others, the
• If you connect to cable TV without a set-top box and experience poor
• Many high-definition (HD) channels upscale standard-definition (SD)
Coaxial cable
waves.
personnel to correct the problem.
Adjust the antenna or use a highly directional outdoor or set-top
antenna with a built-in amplifier.
problem may be caused by a poor or weak signal from the broadcaster
or cable TV provider.
picture quality, you may need to install a set-top box to improve signal
reception and picture quality. Contact your cable TV provider about
upgrading to a set-top box.
content. The picture displayed on your TV is still displayed as SD, thus
the picture quality will not be as clear or crisp as it would be if the
content was originally recorded in HD.
20
www.insigniaproducts.com
NS-40DR420NA16/NS-48DR420NA16
Connecting a DVD or Blu-ray player
Many DVD or Blu-ray players have more than one connection type. To get the best video, you should use the best
connection type available. For more information, see What connection should I use? on page 16.
You can connect a DVD or Blu-ray player using:
•HDMI (best)
• AV (composite video) (good)
HDMI (best)
DVD or Blu-ray
player
On your TV
HDMI cable
connector
HDMI jack
HDMI cable
1 Make sure that your TV’s power cord is unplugged and the DVD or Blu-ray player is turned off.
2 Connect an HDMI cable (not provided) to an HDMI jack on the side of your TV and to the HDMI OUT jack on the
DVD or Blu-ray player.
3 Plug your TV’s power cord into a power outlet, then turn on your TV and DVD or Blu-ray player.
4 On the Home screen, press or to highlight the HDMI 1, HDMI 2, or HDMI 3 tile, then press OK.
Side of TV
Note
An HDMI cable carries both audio and video. You do not need to use any
audio cables.
www.insigniaproducts.com
21
AV (composite video) (good)
Note
Cables are often color-coded to match color-coded jacks.
40"/48" 1080p, 60Hz, LED Insignia Roku TV
On your TV
AV c able
connector
AV j ack
1 Make sure that your TV’s power cord is unplugged and the DVD or Blu-ray player is turned off.
2 Connect an AV cable (not provided) to the VIDEO jack and AUDIO L and R jacks on the back of your TV and to the
AV OUT jacks on the DVD or Blu-ray player.
Audio cable
connectors
Analog
audio jacks
Note
When you connect the audio using the AUDIO L and R jacks, the audio
output is analog.
DVD or Blu-ray
player
AV c able
Back of TV
3 Plug your TV’s power cord into a power outlet, then turn on your TV and DVD or Blu-ray player.
4 On the Home screen, press or to highlight the AV tile, then press OK.
22
www.insigniaproducts.com
NS-40DR420NA16/NS-48DR420NA16
Connecting a game console
Many game consoles have more than one connection type. To get the best video, you should use the best connection
type available. For more information, see What connection should I use? on page 16.
You can connect a game console using:
•HDMI (best)
• AV (composite video) (good)
HDMI (best)
Game console
On your TV
HDMI cable
connector
HDMI jack
HDMI cable
1 Make sure that your TV’s power cord is unplugged and the game console is turned off.
2 Connect an HDMI cable (not provided) to an HDMI jack on the side of your TV and to the HDMI OUT jack on the
game console.
3 Plug your TV’s power cord into a power outlet, then turn on your TV and the game console.
4 On the Home screen, press or to highlight the HDMI 1, HDMI 2, or HDMI 3 tile, then press OK.
Side of TV
Note
An HDMI cable carries both audio and video. You do not need to use any
audio cables.
www.insigniaproducts.com
23
Loading...
+ 64 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.