INGENICO ICT220CLV3 User Manual

U s e r G u i d e

Product name : iCT220/iCT250

Range : COUNTER TOP

INGENICO – 28-32 Boulevard de Grenelle –75015 Paris - FRANCE Tél. 33(0)1 58 01 80 00 - Fax 33 (0)1 58 01 91 35 www.ingenico.com

Contents

1. Introduction __________________________________________________ 3

2. Unpacking ____________________________________________________ 3

3. Recommendations ____________________________________________ 4

3.1. Security _____________________________________________________________ 4

3.2. Telephone emergency, hanging up _______________________________________ 4

3.3. Security of your terminal _______________________________________________ 5

3.4. Standard compliance marking ___________________________________________ 5

3.5. FCC compliance _______________________________________________________ 6

3.6. Main Characteristics ___________________________________________________ 8

4. Installation and connection _____________________________________ 9

4.1. Positioning the terminal ________________________________________________ 9

4.2. Connections __________________________________________________________ 9

4.3. Installing the iCT220/iCT250 – Cable fixing __________________________________ 9

4.3.1. Opening the cable cover _________________________________________________________ 9

4.3.2. Kit Magic Box installation _______________________________________________________ 10

4.3.3. Connect cables ________________________________________________________________ 11

4.3.4. Close cover ___________________________________________________________________ 12

4.4. Installation of the Magic Box ___________________________________________ 12

4.5. Installing SAM (Secure access module) ___________________________________ 13

4.6. Installing MicroSD Card (optional) _______________________________________ 14

5. Installing a paper roll __________________________________________ 15

6. Daily use ____________________________________________________ 16

6.1. Keypad functions ____________________________________________________ 16

6.2. Adjusting the contrast ________________________________________________ 16

6.3. Card insertion _______________________________________________________ 17

6.3.1. Swiping a card _________________________________________________________________ 17

6.3.2. Inserting a chip card ____________________________________________________________ 17

6.3.3. Inserting a chip card in second reader (Optional) _____________________________________ 17

6.3.4. Reading Contactless (Optional) ___________________________________________________ 17

7. Maintenance _________________________________________________ 18

7.1. Paper roll ___________________________________________________________ 18

7.2. Cleaning of the terminal _______________________________________________ 19

7.3. Transport and storage ________________________________________________ 19

7.4. Troubleshooting _____________________________________________________ 19

7.5. Environment (WEEE, Batteries and Packaging) ____________________________ 20

1. Introduction

Cable connection for the telephone network

Magic box

Desktop Power supply unit

iCT220/iCT250 terminal

User guider

Thank you for choosing an Ingenico payment terminal. We recommend you to read carefully this user guide: It gives you the necessary information about safety precautions, unpacking, installation, and maintenance of your terminal.

CAUTION

To benefit from the guarantee-related product, and to respect the security, we ask you to use only the power supply delivered in box with the product, entrusting maintenance operations only to an authorized person. Failure to comply with these instructions will void the manufacturer’s responsibility.

2. Unpacking

ADVICE

Carefully preserve the packaging of the iCT220/iCT250. It must be re-used whenever the terminal is shipped.

According to the model, the following items are included in the iCT220/iCT250 package

The iCT220/iCT250 terminal equipped with its paper roll Magic box ( mandatory use ) The main power supply with primary cable (according to national requirements). The cable connection for the telephone network This installation guide

CAUTION

The power supply unit provided with your equipment is specially designed for Ingenico iCT220/iCT250 terminals. Do not use any other power supply.

3. Recommendations

3.1. Security

Power on/Power down

To power on or power down the iCT220/iCT250 connect or disconnect the power supply from the electric outlet.

Lithium battery

The iCT220/iCT250 is fitted with a lithium battery which is not accessible to the user. Only a qualified technician may be authorized to open the unit and change this component.

Electrical power supply network

Provide an electrical outlet :

- located near the equipment and easily accessible

- which meets the standards and regulations in the country of use.

Telephone network

Provide a phone jack complying with standards and regulations in the country of use.

SAM/SIM or SD Memory Card compartment cover

Located under the terminal, it must be in place during normal operation of the terminal.

Cable compartment cover

The cable compartment cover is located under the terminal, it must be in place during normal operation of the terminal.

3.2. Telephone emergency, hanging up

You have an urgent call to make, when iCT220/iCT250 hangs on the line. In order to get a dial tone…

Place the handset in the hang up position and : press the red key (=cancel)

or disconnect the power supply from the mains network or disconnect the iCT220/iCT250 telephone connector from the telephone call socket,

and place the telephone connector into the telephone wall socket.

You will have a dial tone within 6 seconds.

3.3. Security of your terminal

Upon receipt of your terminal you should check for signs of tampering of the equipment. It is strongly advised that these checks are performed regularly after receipt. You should check, for example: that the keypad is firmly in place; that there is no evidence of unusual wires that have been connected to any ports on your terminal or associated equipment, the chip card reader, or any other part of your terminal. Such checks would provide warning of any unauthorised modifications to your terminal, and other suspicious behaviour of

individuals that have access to your terminal. Your terminal detects any “tampered state”. In this state the terminal will repeatedly flash the message” Alert Irruption!” and further use of the terminal will not be possible. If you observe the “Alert Irruption!” message, you

should contact the terminal helpdesk immediately. You are strongly advised to ensure that privileged access to your terminal is only granted to staff that have been independently verified as being trustworthy.

CAUTION NEVER ask the customer to divulge their PIN Code. Customers should be advised to ensure that they are not being overlooked when entering their PIN Code.

3.4. Standard compliance marking

iCT220

This class (B) digital apparatus complies with Canadian ICES-003 Cet appareil numérique de la classe (B) respecte toutes les exigences de la norme

NMB-003 du Canada.

iCT250

Under Industry Canada regulations, this radio transmitter may only operate using an

antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut

fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils

radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

iCT220 / iCT250

conforms to the following standards and rules :

o IEC 60950-1 2

Ed: Electrical safety of data processing equipment including

electrical office equipment

o FCC part 15 C (ICT250 ), FCC part 15 B(ICT220 ) o FCC part 68 o EN 55024

3.5. FCC compliance

FCC ID : XKB-ICT220 / XKB-ICT250 / XKB-ICT220V3 / XKB-ICT250V3

This equipment as been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interface in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with instruction, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct interface by one more of the following measures :

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into a outlet on circuit different from that to which the receiver

is connected.

Consult the dealer or an experience radio/TV technician for help.

Part 68 of FCC Rules

US : IEOMM01BICT220 / IEOMM01BICT250 US : IEOMM02BICT220V3 / IEOMM02BICT250V3

This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US: AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.

This equipment uses the following USOC jacks: (RJ11C).

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.

The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of this equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications to maintain uninterrupted service. If trouble is experienced with this equipment, please contact INGENICO, or your local INGENICO distributor or service center in the U.S.A. for repair and/or warrant information. If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.

U.S.A service center: Ingenico North America 3025 Windward Plaza, suite 600 Alpharetta, GA 30005

USA

Tel: +1(678) 456 1200 Fax: +1 (678) 456 1201 Email: info.us@ingenico.com

CAUTION

The user is cautioned that any changes or modification not approved by INGENICO could

void user’s authority to operate the equipment.

+ 14 hidden pages