Infinity XPLO-15 LED Strobe V1
Highlite Interna t ional B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
Ordercode: 40280
MANUAL
ENGLISH
Productcode: 40280
Infinity XPLO-15 LED Strobe
Table of contents
Warning ............................................................................................................................................................................... 3
Safety Instructions ......................................................................................................................................................... 4
Operating Determinations .......................................................................................................................................... 5
Rigging ............................................................................................................................................................................ 5
Connection with the mains......................................................................................................................................... 6
Return Procedure .......................................................................................................................................................... 7
Claims .............................................................................................................................................................................. 7
Description of the device ................................................................................................................................................. 8
Frontside.......................................................................................................................................................................... 8
Backside ......................................................................................................................................................................... 9
Installation ........................................................................................................................................................................... 9
Set Up and Operation ....................................................................................................................................................... 9
Control Modes .............................................................................................................................................................10
One Infinity (Stand-alone) ......................................................................................................................................10
Multiple Infinitys (Master/Slave contro l) ...............................................................................................................10
Multiple Infinitys (DMX Control) .............................................................................................................................11
Fixture Linking ...............................................................................................................................................................12
Data Cabling ...............................................................................................................................................................12
Control Panel ...............................................................................................................................................................13
Control Mode ..............................................................................................................................................................13
DMX Addressing ..........................................................................................................................................................13
Menu Overview ...........................................................................................................................................................14
Main Menu Options ....................................................................................................................................................16
1. Presets ....................................................................................................................................................................17
1.1. Editing a preset .................................................................................................................................................17
2. Chases ...................................................................................................................................................................19
2.1. Editing a chase .................................................................................................................................................19
2.2. Editing an effect ...............................................................................................................................................20
2.3. Adding a new step ..........................................................................................................................................21
2.4. Deleting a step..................................................................................................................................................21
3. Settings ...................................................................................................................................................................22
3.1. Security ...............................................................................................................................................................22
3.2. General ..............................................................................................................................................................23
3.3. Factory Default .................................................................................................................................................25
3.4. DMX Mode .........................................................................................................................................................26
3.5. DMX Address Setting ........................................................................................................................................26
3.6. Display ................................................................................................................................................................27
4. Fixture Lock ...........................................................................................................................................................28
5. Password ...............................................................................................................................................................28
6. Status ......................................................................................................................................................................29
DMX Channels .............................................................................................................................................................30
1 channel (Single Channel) ...................................................................................................................................30
3 channels (Three Channel) ..................................................................................................................................30
4 channels (Four Channel) ....................................................................................................................................30
6 channels (16-bit Control) ....................................................................................................................................31
28 channels (Zone Mapping) ................................................................................................................................32
RDM Parameter IDs.....................................................................................................................................................34
XPLO-15 LED Strobe RDM Product Parameter IDs .............................................................................................34
XPLO-15 LED Strobe RDM UID ................................................................................................................................34
XPLO-15 LED Strobe RDM Parameter IDs .............................................................................................................35
XPLO-15 LED Strobe RDM Manufacturer Status IDs ...........................................................................................36
XPLO-15 LED Strobe RDM Manufacturer Specific PIDs for Root Device ........................................................37
1
Productcode: 40280
Infinity XPLO-15 LED Strobe
Maintenance ....................................................................................................................................................................37
Troubleshooting ...............................................................................................................................................................38
No Light .........................................................................................................................................................................38
No Response to DMX..................................................................................................................................................38
Product Specifications ....................................................................................................................................................40
Dimensions ........................................................................................................................................................................41
Notes ..................................................................................................................................................................................42
2
Productcode: 40280
Infinity XPLO-15 LED Strobe
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
• Infinity XPLO-15 LED Strobe
• Power cable Neutrik Powercon True1 to Schuko 1,5 m (90471)
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason, when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving life expectancy is of higher priority, place care in providing for lower
operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.
3
Productcode: 40280
Infinity XPLO-15 LED Strobe
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
• be qualified.
• follow the instructions of this manual.
Before the initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
• Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
• Never remove warning or informative labels from the unit.
• Never use anything to cover the ground contact.
• Never lift the fixture by holding it at the projector-head, as the mechanics may be damaged. Always
hold the fixture at the transport handles.
• Never place any material over the lens.
• Never look directly into the light source.
• Never leave any cables lying around.
• Do not connect this device to a dimmerpack.
• Do not switch the device on and off in short intervals, as this would reduce the device’s life.
• Do not touch the device’s housing bare-handed during its operation (housing becomes very hot).
Allow the fixture to cool for at least 5 minutes before handling.
• Do not shake the device. Avoid brute force when installing or operating the device.
• Only use device indoor, avoid contact with water or other liquids.
• Only operate the fixture after having checked that the housing is firmly closed and all screws are
tightly fastened.
• Only operate the device after having familiarized with its functions.
• Avoid flames and do not put close to flammable liquids or gases.
• Always keep case closed while operating.
• Always allow free air space of at least 50 cm around the unit for ventilation.
• Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord by the plug. Never pull out the plug by tugging the power cord.
• Make sure that the device is not exposed to extreme heat, moisture or dust.
• Make sure that the available voltage is not higher than stated on the rear panel.
• Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
• If the lens is obviously damaged, it has to be replaced. So that its functions are not impaired, due to
cracks or deep scratches.
• If device is dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
4
Productcode: 40280
Infinity XPLO-15 LED Strobe
• If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
• If your Infinity device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Infinity dealer for service.
• For adult use only. Infinity must be installed out of the reach of children. Never leave the unit running
unattended.
• Never attempt to bypass the thermostatic switch or fuses.
• For replacement use fuses of same type and rating only.
• The user is responsible for correct positioning and operating of the Infinity. The manufacturer will not
accept liability for damages caused by the misuse or incorrect installation of this device.
• This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
• Repairs, servicing and electric connection must be carried out by a qualified technician.
• WARRANTY: Till one year after date of purchase.
Operating Determinations
• This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
• The minimum distance between light output and the illuminated surface must be more than 1 meter.
• The maximum ambient temperature ta = 40°C must never be exceeded.
• The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
• If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the warranty becomes void.
• Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself!
Always have the inspections carried out by an authorized dealer!
Procedure:
• If the projector is lowered from the ceiling or high joists, professional trussing systems have to be used.
• Use a clamp to mount the projector, with the mounting bracket, to the trussing system.
• The projector must never be fixed swinging freely in the room.
• The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety cable.
• When rigging, derigging or servicing the projector, always make sure, that the area below the
installation site is secured and that there are not any unauthorized people around.
5
Productcode: 40280
Infinity XPLO-15 LED Strobe
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
The Infinity can be placed on a flat stage floor or mounted to any kind of truss with a clamp.
Improper installation can cause serious injuries and/or damage of property!
Connection with the mains
Connect the device to the mains with the power-plug.
Always check if the right color cable is connected to the right place.
Make sure that the device is always properly connected to the earth!
Improper installation can cause serious injuries and/or damage of property!
6
Productcode: 40280
Infinity XPLO-15 LED Strobe
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail aftersales@highlite.nl
Be prepared to provide the model number, serial number and a brief description of the cause for the
return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the
customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
and request an RMA prior to shipping the fixture.
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any shortcomings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
otherwise agreed in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.
7
Productcode: 40280
Infinity XPLO-15 LED Strobe
Frontside
Fig. 01
Description of the device
Features
The Infinity XPLO-15 LED Strobe is a professional strobe effect for the most demanding users.
• Input voltage: 100-240V, 60/50Hz
• Power consumption: 132W
• DMX channels: 1, 3, 4, 6 (16-bit Control), 28 (Zone Mapping) channels
• LCD display with gravity sensor
• Light source: 576 x 6500K Luxeon SMD
• Light output: 28000 lux
• Color temperature: 6500K
• Control modes: Stand-alone, Master/Slave, DMX/RDM
• Control protocol: DMX-512, RDM
• Dimmer: 0-100%
• Strobe: 0,5-30Hz
• Dimming Curves: Dimming curves: Linear, PL-Curve, S-Curve , Squa r e -Curve
• Beam Angle: 115°
• IP rating: IP54
• Housing: Metal & Flame retardant plastic
• Connections: Neutrik True1 and 3-pin XLR IN/OUT
• Dimensions: 319 x 130 x 255 mm (LxWxH)
• Weight: 5,4 kg
01) Mounting bracket with inclination screw
02) Adjustment screw
03) 576 x 6500K Luxeon SMD
8
Productcode: 40280
Infinity XPLO-15 LED Strobe
Fig. 02
Backside
04) 3-pin DMX/RDM signal connector OUT
05) Neutrik True1 power connector 100-240V OUT
06) LCD Display + control buttons
07) Neutrik True1 power connector 100-240V IN
08) 3-pin DMX/RDM signal connector IN
Installation
Remove all packing materials from the Infinity XPLO-15 LED Strobe. Check if all foam and plastic padding
is removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply.
9
Productcode: 40280
Infinity XPLO-15 LED Strobe
There are 3 modes:
• Stand-alone
• Master/Slave
• DMX-512 (1CH, 3CH, 4CH, 6CH, 28CH)
The pins:
01) Earth
Multiple Infinitys (Master/Slave control)
Fig. 03
Control Modes
One Infinity (Stand-alone)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Plug the end of the electric mains power cord into a proper electric power supply socket.
03) When the Infinity is not connected with a DMX cable, it functions as a stand-alone device.
Please see pages 17-29 for more information about the Stand-alone Mode.
Multiple Infinitys (Master/Slave control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Use a 3-pin XLR cable to connect the Infinity.
02) Signal -
03) Signal +
03) Link the units as shown in fig. 03. Connect the first unit's DMX "out" socket with the second unit's "in"
socket, using a DMX-signal cable. Repeat this process to link the second, third, and fourth units.
You can use the same functions on the master device as described on pages 17-29 (Stand-alone
Mode). This means that you can set your desired operation mode on the master device and all
slave devices will react the same as the master device.
10
Productcode: 40280
Infinity XPLO-15 LED Strobe
Multiple Infinitys DMX Set Up
Fig. 04
Multiple Infinitys (DMX Control)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Use a 3-pin XLR cable to connect the Infinity and other devices.
04) Link the units as shown in fig. 04. Connect the first unit's DMX "out" socket with the second unit's "in"
socket, using a DMX-signal cable. Repeat this process to link the second, third, and fourth units.
05) Supply electric power: Plug electric mains power cords into each unit's Neutrik True1 socket, then
plug the other end of the mains power cord into proper electric power supply sockets, starting with
the first unit. Do not supply power before the whole system is set up and connected properly.
11
Note : Link all cables before connecting electric power
Productcode: 40280
Infinity XPLO-15 LED Strobe
Important:
Fixtures on a serial data link must be daisy-chained in a single line. To comply with the
isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a power link: 26 fixtures @ 240V
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
EIA-485 standard, no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX optically
Maximum recommended number of fixtures on a DMX data link: 30 fixtures
Maximum recommended number of fixtures on a power link: 13 fixtures @ 100V
Data Cabling
To link fixtures together, you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable,
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio DMX Data Cables
• DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin.
Ordercode FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
• DAP Au di o X -type data cable XLR/M 3-pin > X LR /F 3-pin. Ordercode FLX0175 (0,75 m ),
FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
• DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
• DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
• DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m),
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).
12
Productcode: 40280
Infinity XPLO-15 LED Strobe
A)
Home button
Fig. 05
Display Off after 35 seconds
Control Panel
B)
Edit Preset button
C)
Chase button
D)
Address Setting button
E)
Infinity Logo button
F)
LEFT button
G)
RIGHT button
H)
OK/ENTER
I)
UP button
J)
DOWN button
K)
LCD display
Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it,
the controller will display the saved DMX address the next time.)
DMX Addressing
The control panel on the front side of the base allows you to assign the DMX fixture address, which is the
first channel from which the Infinity will respond to the controller.
Please note when you use the controller, the unit has 28 channels.
When using multiple Infinity’s, make sure you set the DMX addresses right.
Therefore, the DMX address of the first Infinity should be 1(001); the DMX address of the second Infinity
should be 1+28=29 (029); the DMX address of the third Infinity should be 29+28=57 (057), etc.
Please, be sure that you don’t have any overlapping channels in order to control each Infinity correctly.
If two or more Infinity’s are addressed similarly, they will work similarly.
Controlling:
After having addressed all Infinity fixtures, you may now start operating these via your lighting controller.
Note: After switching on, the Infinity will automatically detect whether DMX 512 data is received or not. If
there is no data received at the DMX-input, the “LED“ on the control panel will not flash.
The problem may be:
● The XLR cable from the controller is not connected with the input of the Infinity.
● The controller is switched off or defective, the cable or connector is detective, or the signal wires are
Note: It’s necessary to insert a XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.
swapped in the input connector.
When no button is pressed for 35 seconds, the display will turn off.
To light up the display, you have to press one of the 10 buttons on the control panel..
Once you have pressed the button, the display will light up.
13
Productcode: 40280
Infinity XPLO-15 LED Strobe
Menu Overview
14
Productcode: 40280
Infinity XPLO-15 LED Strobe
15
Productcode: 40280
Infinity XPLO-15 LED Strobe
Main Menu Options
Presets
Chases
Settings Menu
Fixture Lock
Password
System Status
Home
Presets
Chases
DMX Address Settin g
Main Screen
Up
Down
OK
Left
Right
The device’s output is divided into zones. In the example below, zones 2, 3, 5, 7 and 8 are switched ON.
16
Productcode: 40280
Infinity XPLO-15 LED Strobe
1. Presets
1.1. Editing a preset
01) While in the main menu, press the , , and buttons to choose and press
the button to open the menu. You can also press the button. The display will show:
02) Press the and to toggle between the following options:
• Preset (Choose between 31 built-in presets or OFF)
• Master Intensity (Dimmer intensity, between 0-100%, from low to high intensity)
• Strobe Rate (Strobe intensity, between Single Flash - 30,488Hz)
• Strobe Duration (Between 0-8364Ms, from short to long duration)
• Effects (see below)
03) Press the and buttons to, respectively, decrease/increase the values.
17
Productcode: 40280
Infinity XPLO-15 LED Strobe
04) Press the button to proceed to zone edition. The display will show:
05) Press the and buttons to switch between the zones.
06) Press the and to switch the zones ON or OFF.
07) Once you have applied all the necessary changes, press the to confirm. The display will show:
08) Press the and buttons to choose the preset which you wish to overwrite.
09) Press the to confirm.
10) Press the and buttons to choose YES or NO, when asked if you are sure that you want to
save the preset and press the button to confirm.
18
Productcode: 40280
Infinity XPLO-15 LED Strobe
2. Chases
2.1. Editing a chase
01) While in the main menu, press the , , and buttons to choose and press
the button to open the menu. You can also press the button. The display will show:
02) Press the and buttons to choose one of the 10 built-in chases or one of the 8 user chases.
Note: If you have chosen a user chase, you can edit its characteristics.
03) Press the and to choose Edit User Chase and press the button to confirm. The display
will show:
04) Press the and buttons to toggle between the following options.
• User Chase (Choose one of the 8 user chases)
• Edit Step (Edit the characteristics of the desired step)
• Strobe Duration (Between 0-8364Ms, from short to long duration)
• New Step (Add new step)
• Delete Step
• Effects (Edit the chase’s characteristics)
05) Press the and buttons, to adjust the values.
06) Press the and buttons to choose Edit Step and press the and buttons to choose
the step which you want to edit.
07) Press the button to enter edition mode. The display will show:
19
Productcode: 40280
Infinity XPLO-15 LED Strobe
08) Press the and buttons to choose one of the existing presets which, later on, can be edited.
There are 31 presets to choose from.
09) Press the and buttons to choose Master Intensity.
10) Press the and buttons to adjust the dimmer intensity.
The adjustment range is between 0-100%.
11) Press the and buttons to enter the zone preview mode.
12) Press the and buttons to choose one of the 8 zones which you want to
activate/deactivate.
13) Press the and buttons to activate/deactivate the desired zone.
14) Press the button to save changes.
2.2. Editing an effect
01) Return to step 4 (page 19) and choose Effects. Press the button to confirm. The display will show:
02) Press the and buttons to choose Direction.
03) Press the and buttons to choose Left or Right. The effect will now move to the left or to the
right.
04) Press the and buttons to choose Mode.
05) Press the and buttons to choose one of the 2 modes.
06) Press the and buttons to choose Number of Color.
07) Press the and buttons to adjust the number of the active zones. The adjustment range is
between 1-8. 1 = all zones active, 8 = one zone active.
08) Press the and buttons to choose zone preview mode.
20
Productcode: 40280
Infinity XPLO-15 LED Strobe
09) Press the and buttons to choose one of the 8 zones which you want to
activate/deactivate.
10) Press the and buttons to activate/deactivate the desired zone.
11) Press the button to save changes.
12) Press the and buttons to choose Yes or No, when asked if you are sure that you want to
save changes, and press the button to confirm your choice.
2.3. Adding a new step
01) Return to step 4 (page 19) and choose New Step. The display will show:
02) Repeat steps 8-14 (pages 19-20) to create a new step.
2.4. Deleting a step
01) Return to step 4 (page 19).
02) Press the and buttons to choose Edit Step.
03) Press the and buttons to choose the step which you want to delete.
04) Press the and buttons to choose Delete Step and press the button to delete the
desired step.
21
Productcode: 40280
Infinity XPLO-15 LED Strobe
3. Settings
01) While in the main menu, press the , , and buttons to choose and press
the button to open the menu. The display will show:
02) Press the and buttons to toggle between the 5 options:
• Security
• General
• Factory Default
• DMX
• Display
3.1. Security
01) Press the and buttons to choose Security and press the button to enter the menu. The
display will show:
02) Press the and buttons to toggle between the available options.
03) In order to adjustChoose one of the 5 safety keys (Enter PassPIN, Level 1 PIN, Level 2 PIN, Level 3 PIN
or Power-up Level) and press the button to open the menu. For example, if you choose Enter
PassPIN, the display will show:
22
Productcode: 40280
Infinity XPLO-15 LED Strobe
04) Press the and buttons to choose the digit which you want to edit. The chosen digit will light
up in blue.
05) Press the and buttons to adjust the value. The adjustment range is between 0-9.
06) Once the security key has been inserted, press the button to store it.
07) Return to step 3 and choose Power-up Level.
08) Press the and buttons to choose the password which will be needed to unlock the device
on the next start-up.
3.2. General
01) Press the and buttons to choose General and press the button to enter the menu.
The display will show:
02) Press the and buttons to toggle between the following available options:
• Power-up (Choose between 31 presets, 10 chases, 8 user chases, Last Setting or OFF)
• Mode (Set the device as a master or a slave device.)
Note: In order to be able to adjust the device’s functions by means of DMX, the device must be set to
Master.
• Dimming Curve (Choose between PL-Curve, Linear-Curve, Square-Curve or S-Curve. See the
chart below, describing differences between the particular dimming curve patterns.)
03) Press the and buttons to adjust the options.
23
Productcode: 40280
Infinity XPLO-15 LED Strobe
Fig. 06
Dimming Curves
24
Productcode: 40280
Infinity XPLO-15 LED Strobe
3.3. Factory Default
01) Press the , , to choose Factory Default and press the button to enter the menu.
The display will show:
02) Press the and buttons to toggle between the following available options:
• Protected
• Load Factory
03) Press the and buttons to choose Protected and press the and buttons to
choose between No or Preset&Chase. This option defines whether the whole menu or only the
Settings menu are locked, providing that the safety lock has been activated.
04) Press the and buttons to choose Load Factory.
05) Press the and buttons to choose between YES and NO.
06) Press the button to confirm your choice.
07) If you have chosen YES, you will again have to choose between YES or NO, when asked if you are
sure of your choice . Press the and buttons to make your choice.
08) Press the button to confirm.
09) The device will now perform a software reset.
25
Productcode: 40280
Infinity XPLO-15 LED Strobe
3.4. DMX Mode
01) Press the and buttons to choose DMX and press the button to enter the menu. The
display will show:
02) Press the and buttons to toggle between the following 4 options:
• DMX Enable (Choose between Enable and Disable, to activate/deactivate DMX. )
• Address (Set the desired DMX address. The adjustment range is between 1-511, depending on
the active channel mode. )
• Map (Choose between 5 channel modes: Single channel, Three Channel, Four Channel, 16-bit
Control, Zone Mapping. )
• When no DMX (Choose between OFF, Hold, Power-up and Last Action. See below for more
information.)
OFF
When the device is not receiving a DMX signal, the output will be switched OFF.
Hold
When the device is not receiving a DMX signal, it will fall back on the last working DMX signal.
Power-up
When the device is not receiving a DMX signal, it will fall back on the power-up value from Settings menu.
Last Action
When the device is not receving a DMX signal, it will restore the last menu action.
03) Press the and buttons to adjust the chosen options.
04) Once all the necessary changes have been made, press the button to confirm.
3.5. DMX Address Setting
01) While in the main menu, press the button to open the menu. The display will show:
26
Productcode: 40280
Infinity XPLO-15 LED Strobe
02) Press the to enter edition mode. The display will show:
03) Press the and buttons to adjust the chosen digit (which lights up in blue).
04) Press the and buttons to choose another digit to edit and repeat the previous step.
3.6. Display
01) Press the and buttons to choose Display and press the button to enter the menu.
The display will show:
02) Press the and buttons to toggle between the following options:
• Flip Display (Choose between Auto – automatic flip; No – no flip; Yes – horizontal flip)
• Off Time (Time after which the display turns off, when no button is pressed. The available options
are: ON – display continuously ON, 30s, 1min, 5min, 10min)
• Language Select (Select your preferred language. In this software version, English is the only
option.)
03) Press the and buttons to adjust the chosen options.
27
Productcode: 40280
Infinity XPLO-15 LED Strobe
4. Fixture Lock
01) While in the main menu, press the , , and buttons to choose and press
the button to open the menu. The display will show:
02) Press the and buttons to choose either Yes or No.
03) Press the button to confirm your choice.
04) If you have chosen Yes, the device will return to the main screen.
05) If you want to enter the menu, you are now obliged to insert the security key (see page 22).
5. Password
01) While in the main menu, press the , , and buttons to choose and press
the button to open the menu.
02) You will now be asked to insert the security key.
03) Press the and buttons to choose the digit which you want to edit. The chosen digit will light
up in blue.
04) Press the and buttons to adjust the value. The adjustment range is between 0-9.
05) Once the security key has been inserted, press the button to confirm.
28
Productcode: 40280
Infinity XPLO-15 LED Strobe
6. Status
In this menu you can see the current status of the device.
01) While in the main menu, press the , , and buttons to choose and press
the button to open the menu. The display will show:
02) The display shows the current dimmer intensity, as well as the current zone preview.
03) Press the button to proceed to the second screen. The display will show:
04) The pieces of information displayed on the screen are as follows:
• Temperature (The current temperature of the device)
• Warning Low (The temperature which triggers low priority overheating alarm)
• Warning High (The temperature which triggers high priority overheating alarm)
• Min_Value (The lowest temperature which ensures proper performance of the device)
• Max_Value (The highest temperature which ensures proper performance of the device)
• Max_Intensity (The maximum available dimmer intensity)
05) Press the button to proceed to the third screen. The display will show:
06) The pieces of information displayed on the screen are as follows:
• RDM UID (The current RDM software version)
• Firmware Version (The current software version)
29
Productcode: 40280
Infinity XPLO-15 LED Strobe
Channel 1 – Strobe
0-255
Strobe flash frequency, from slow to fast
Channel 1 – Dimmer intensity
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 2 – Strobe Duration Dimmer must be open
0-255
Strobe flash duration, from short to long
Channel 3 – Strobe Dimmer must be open
0-255
Strobe flash frequency, from low to high frequency
Channel 1 – Dimmer intensity
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 2 – Strobe Duration Dimmer must be open
0-255
Strobe flash duration, from short to long
Channel 3 – Strobe Dimmer must be open
0-255
Strobe flash frequency, from low to high frequency
Channel 4 – Effects Dimmer must be open
0-5
Not functional
6-42
Ramp Up (Fade In)
43-85
Ramp Down (Fade Out)
86-128
Ramp up/down (Fade In/Out)
129-171
Random effects
172-173
Left zone
174-175
Center zone
176-178
Right zone
179-180
Pattern A
181-182
Pattern B
183-184
Pattern C
185-186
Pattern D
DMX Channels
The device’s output is divided into zones. In the example below, zones 2, 3, 5, 7 and 8 are switched ON.
1 channel (Single Channel)
3 channels (Three Channel)
4 channels (Four Channel)
30
Productcode: 40280
Infinity XPLO-15 LED Strobe
187-214
Random patterns
215-235
Chase 1 - from left to right, from slow to fast
236-255
Chase 2 - from right to left, from slow to fast
Channel 1 – Dimmer intensity
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 2 – 16-bit dimmer intensity
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 3 – Effects Dimmer must be open
0-5
Not functional
6-42
Ramp Up (Fade In)
43-85
Ramp Down (Fade Out)
86-128
Ramp up/down (Fade In/Out)
129-171
Random effects
172-173
Left zone
174-175
Center zone
176-178
Right zone
179-180
Pattern A
181-182
Pattern B
183-184
Pattern C
185-186
Pattern D
187-214
Random patterns
215-235
Chase 1 - from left to right, from slow to fast
236-255
Chase 2 - from right to left, from slow to fast
Channel 4 – Dimming curves Dimmer must be open
0-4
Default
5-29
Not functional
30-34
Linear dimming curve
35-39
Square dimming curve
40-44
S-Curve dimming curve
45-49
PL-Curve dimming curve
50-255
Not functional
Channel 5 – Strobe Duration Dimmer must be open
0-255
Strobe flash duration, from short to long
Channel 6 – Strobe Dimmer must be open
0-255
Strobe flash frequency, from low to high frequency
6 channels (16-bit Control)
31
Productcode: 40280
Infinity XPLO-15 LED Strobe
Channel 1 – Dimmer intensity
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 2 – 16-bit dimmer intensity
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 3 – Effects Dimmer must be open
0-5
Not functional
6-42
Ramp Up (Fade In)
43-85
Ramp Down (Fade Out)
86-128
Ramp up/down (Fade In/Out)
129-171
Random effects
172-173
Left zone
174-175
Center zone
176-178
Right zone
179-180
Pattern A
181-182
Pattern B
183-184
Pattern C
185-186
Pattern D
187-214
Random patterns
215-235
Chase 1 - from left to right, from slow to fast
236-255
Chase 2 - from right to left, from slow to fast
Channel 4 – Dimming curves Dimmer must be open
0-4
Default
5-29
Not functional
30-34
Linear dimming curve
35-39
Square dimming curve
40-44
S-Curve dimming curve
45-49
PL-Curve dimming curve
50-255
Not functional
Channel 5 – Zone 1 - Dimmer intensity Dimmer must be open
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 6 – Zone 1 - Strobe Duration Dimmer must be open
0-255
Strobe flash duration, from short to long
Channel 7 – Zone 1 - Strobe Dimmer must be open
0-255
Strobe flash frequency, from low to high frequency
Channel 8 – Zone 2 - Dimmer intensity Dimmer must be open
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 9 – Zone 2 - Strobe Duration Dimmer must be open
0-255
Strobe flash duration, from short to long
Channel 10 – Zone 2 - Strobe Dimmer must be open
0-255
Strobe flash frequency, from low to high frequency
28 channels (Zone Mapping)
32
Productcode: 40280
Infinity XPLO-15 LED Strobe
Channel 11 – Zone 3 - Dimmer intensity Dimmer must be open
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 12 – Zone 3 - Strobe Duration Dimmer must be open
0-255
Strobe flash duration, from short to long
Channel 13 – Zone 3 - Strobe Dimmer must be open
0-255
Strobe flash frequency, from low to high frequency
Channel 14 – Zone 4 - Dimmer intensity Dimmer must be open
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 15 – Zone 4 - Strobe Duration Dimmer must be open
0-255
Strobe flash duration, from short to long
Channel 16 – Zone 4 - Strobe Dimmer must be open
0-255
Strobe flash frequency, from slow to fast
Channel 17 – Zone 5 - Dimmer intensity Dimmer must be open
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 18 – Zone 5 - Strobe Duration Dimmer must be open
0-255
Strobe flash duration, from short to long
Channel 19 – Zone 5 - Strobe Dimmer must be open
0-255
Strobe flash frequency, from slow to fast
Channel 20 – Zone 6 - Dimmer intensity Dimmer must be open
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 21 – Zone 6 - Strobe Duration Dimmer must be open
0-255
Strobe flash duration, from short to long
Channel 22 – Zone 6 - Strobe Dimmer must be open
0-255
Strobe flash frequency, from slow to fast
Channel 23 – Zone 7 - Dimmer intensity Dimmer must be open
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 24 – Zone 7 - Strobe Duration Dimmer must be open
0-255
Strobe flash duration, from short to long
Channel 25 – Zone 7 - Strobe Dimmer must be open
0-255
Strobe flash frequency, from slow to fast
Channel 26 – Zone 8 - Dimmer intensity Dimmer must be open
0-255
Gradual adjustment, from dark to brightest 0-100%
33
Productcode: 40280
Infinity XPLO-15 LED Strobe
Channel 27 – Zone 8 - Strobe Duration Dimmer must be open
0-255
Strobe flash duration, from short to long
Channel 28 – Zone 8 - Strobe Dimmer must be open
0-255
Strobe flash frequency, from slow to fast
Model ID
Manufacturer
Model Description
Product Category
0x1109
Infinity(Highlite International)
XPLO-15 LED Strobe
0x0509
UID
MSB of ESTA
29H
LSB of ESTA
B4H
00H
LSB of
Unique Seq.
MSB of
Unique Seq.
LSB of
Unique Seq.
RDM Parameter IDs
The following tables outline and describe all the RDM parameters IDs associated with the XPLO-15 LED
Strobe.
XPLO-15 LED Strobe RDM Product Paramet er IDs
XPLO-15 LED Strobe RDM UID
34
Productcode: 40280
Infinity XPLO-15 LED Strobe
Get
Allowed
Set
Allowed
RDM Parameter IDs
Value
Comment
Implemented
Category - Network Management
DISC_UNIQUE_BRANCH
0x0001 ■
DISC_MUTE
0x0002 ■
DISC_UN_MUTE
0x0003 ■ ■
PROXIED_DEVICES
0x0010 ■
PROXIED_DEVICES_COUNT
0x0011 ■ ■
COMMS_STATUS
0x0015
Category - Status Collection
■
QUEUED_MESSAGE
0x0020 ■ ■
STATUS_MESSAGES
0x0030 ■
■ STATUS_ID_DESCRIPTION
0x0031 ■
■
CLEAR_STATUS_ID
0x0032 ■ ■ ■
SUB_DEVICE_STATUS_REPORT_THRESHOLD
0x0033
Category - RDM Informati on
■ SUPPORTED_PARAMETERS
0x0050
Support required
required set.
■
■ PARAMETER_DESCRIPTION
0x0051
Support required
message.
■
Category - Product Information
■
DEVICE_INFO
0x0060 ■ ■
PRODUCT_DETAIL_ID_LIST
0x0070
■ DEVICE_MODEL_DESCRIPTION
0x0080 ■
■ MANUFACTURER_LABEL
0x0081 ■ ■ ■
DEVICE_LABEL
0x0082 ■
■
■
FACTORY_DEFAULTS
0x0090 ■
■ LANGUAGE_CAPABILITIES
0x00A0 ■ ■
LANGUAGE
0x00B0 ■
SOFTWARE_VERSION_LABEL
0x00C0 ■ ■
BOOT_SOFTWARE_VERSION_ID
0x00C1 ■
BOOT_SOFTWARE_VERSION_LABEL
0x00C2
Category - DMX512 Setup
■
■
DMX_PERSONALITY
0x00E0 ■ ■
DMX_PERSONALITY_DESCRIPTION
0x00E1 ■
■
■
DMX_START_ADDRESS
0x00F0
Required if
DMX Slot
■
■
SLOT_INFO
0x0120 ■ ■
SLOT_DESCRIPTION
0x0121 ■ ■
DEFAULT_SLOT_VALUE
0x0122
Category - Sensors 0x02xx
■
SENSOR_DEFINITION
0x0200 ■ ■ ■
SENSOR_VALUE
0x0201 ■
XPLO-15 LED Strobe RDM Parameter IDs
only if supporting
parameters
beyond the
minimum
for
Manufacturer-
Specific PIDs
exposed in
SUPPORTED_
PARAMETERS
35
device uses a
Productcode: 40280
Infinity XPLO-15 LED Strobe
Get
Allowed
Set
Allowed
RDM Parameter IDs
Value
Comment
Implemented
■
RECORD_SENSORS
0x0202
Category - Dimmer Settings 0x03xx - FUTURE USE
Category - Power / Lamp Settings 0x04xx
■
■
DEVICE_HOURS
0x0400 ■ ■
LAMP_HOURS
0x0401 ■ ■
LAMP_STRIKES
0x0402 ■ ■
LAMP_STATE
0x0403 ■ ■
LAMP_ON_MODE
0x0404 ■ ■
DEVICE_POWER_CYCLES
0x0405
Category - Display Settings 0x05xx
■
■
DISPLAY_INVERT
0x0500 ■
■
■
DISPLAY_LEVEL
0x0501
Category - Configuration 0x06xx
■
■
PAN_INVERT
0x0600
■
■
TILT_INVERT
0x0601
■
■
PAN_TILT_SWAP
0x0602 ■ ■
REAL_TIME_CLOCK
0x0603
Category - Control 0x10xx
■
■
IDENTIFY_DEVICE
0x1000 ■ ■
RESET_DEVICE
0x1001
■
■
POWER_STATE
0x1010
■
■
PERFORM_SELFTEST
0x1020 ■
SELF_TEST_DESCRIPTION
0x1021
■
CAPTURE_PRESET
0x1030
■
■
PRESET_PLAYBACK
0x1031
Manufacturer spec ific messages are in the range of 0x8000 – 0xFFDF. Each manufacturer specific Status ID
Status ID Message
Value
Data Value 1
Data Value 2
Status ID Description
8100H
00H
00H
ALL OK
XPLO-15 LED Strob e RDM Ma nu factu r er Status IDs
shall have a unique meaning which shall be consistent across all products having a given manufacturer ID.
See table B-2, ANSI E1.20-2010.
36
Productcode: 40280
Infinity XPLO-15 LED Strobe
Get
Set
RDM
IDs
Type
Length
Unit
Prefix
Min
Max
Default
Description
Category - Manufacturer Defined PIDs - Range is 0x8000-0xffdf (See ANSI E1.20-2010 Standard, Table A-3)
■ ■ 8A00H
U8
1
None
None
0
100
100
Dimmer
■ ■ 8AB2H
U8
1
None
None
1
18 1 Chase
■ ■ 8AB1H
U8
1
None
None
0
31 0 Preset
■ ■ 8A92H
U8
1
None
None
0
255 0 Strobe
■ ■ 8A94H
U8
1
None
None
0
85 0 Duration
■ ■ 8A40H
S8 1 DB
None
0 1 0
Link Mode
■ ■ 8AA1H
S8 1 DB
None
0 3 0
Dimming
curve
■ ■ 8A0CH
S8 1 DB
None
0 3 0
DMX Fail
Mode
■ ■ 8AA0H
U8
1
None
None
0 4 0
Backlight
OFF Time
■ ■ 8AA2H
U8
1
None
None
0
50 0 Power-up
setup
■ ■ 8A41H
U8
1
None
None
0 1 0
Lock
fixture
■ ■ 8A98H
U8
1
None
None
0
255 0 Effect
XPLO-15 LED Strobe RDM Manufacturer Specific PIDs for Root Device
Allowed
Allowed
Parameter
Maintenance
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by an expert after every year in the course of an acceptance test.
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by a skilled person once a year.
The following points have to be considered during the inspection:
01) All screws used for installing the device or parts of the device have to be tightly connected and
must not be corroded.
02) There may not be any deformations on housings, fixations and installation spots.
03) Mechanically moving parts like axles, eyes and others may not show any traces of wearing.
04) The electric power supply cables must not show any damages or material fatigue.
The Infinity XPLO-15 LED Strobe requires almost no maintenance. However, you should keep the unit
clean. Otherwise, the fixture’s light output will be significantly reduced. Disconnect the mains power
supply, and then wipe the cover with a damp cloth. Do not immerse in liquid. Wipe lens clean with glass
cleaner and a soft cloth. Do not use alcohol or solvents.
The front lens will require weekly cleaning, as smoke-fluid tends to build up residues, reducing the lightoutput very quickly.
Please clean internal components once a year with a light brush and vacuum cleaner.
Keep connections clean. Disconnect electric power, and then wipe the DMX and audio connections
with a damp cloth. Make sure connections are thoroughly dry before linking equipment or supplying
electric power.
37
Productcode: 40280
Infinity XPLO-15 LED Strobe
Troubleshooting
This troubleshooting guide is meant to help solve simple problems.
If a problem occurs, carry out the steps below in sequence until a solution is found. Once the unit
operates properly, do not carry out following steps.
No Light
If the light effect does not operate properly, refer servicing to a technician.
Suspect three potential problem areas as: the power supply and the LEDs.
01) Power supply. Check that the unit is plugged into an appropriate power supply.
02) The LEDs. Return the Infinity to your Infinity dealer.
03) If all of the above appears to be O.K., plug the unit in again.
04) If you are unable to determine the cause of the problem, do not open the Power Spot, as this may
damage the unit and the warranty will become void.
05) Return the device to your Infinity dealer.
No Response to DMX
Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card malfunction.
01) Check the DMX setting. Make sure that DMX addresses are correct.
02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power.
Try your DMX control again.
03) Determine whether the controller or light effect is at fault. Does the controller operate properly with
other DMX products? If not, take the controller in for repair. If so, take the DMX cable and the light
effect to a qualified technician.
38
Productcode: 40280
Infinity XPLO-15 LED Strobe
Problem
Probable cause(s)
Solution
• Return the device to your local
dealer.
Fixtures reset
controller
The controller is not connected.
• Connect controller.
• Check data quality. If much lower
disturbing the link
• Inspect connections and cables.
or replace damaged cables
Data link not terminated with 120
Ohm termination plug
• Insert termination plug in output
jack of the last fixture on the link
Incorrect addressing of the fixtures
• Check address setting
• Bypass one fixture at a time until
serviced by a qualified technician
• Install a phase-reversing cable
erratically
• Allow the fixture to cool down
• Turn up the air conditioning
• Disconnect the fixture and return it
to your dealer
The power supply settings do not
frequency
• Disconnect fixture. Check settings
One or more
fixtures do not
function at all
correctly, but all
respond
erratically or not
at all to the
Fixtures reset
correctly, but
some respond
erratically or not
at all to the
controller
No light or lamp
cuts out
intermittently
No power to the fixture
Internal fuse blown
3-pin XLR Out of the controller
does not match XLR Out of the first
fixture on the link (i.e. signal is
reversed)
Poor data quality
Bad data link connection
One of the fixtures is defective and
disturbs data transmission on the
link
3-pin XLR Out on the fixtures does
not match (pins 2 and 3 reversed)
Fixture is too hot
LEDs damaged
• Check if power is switched on and
cables are plugged in
• Install a phase reversing cable
between the controller and the
first fixture on the link
than 100 percent, the problem
may be a bad data link
connection, poor quality or
broken cables, missing termination
plug, or a defective fixture
Correct poor connections. Repair
normal operation is restored:
unplug both connectors and
connect them directly together.
• Have the defective fixture
between the fixtures or swap pin 2
and 3 in the fixture that behaves
• Make sure air vents in control
panel and the front lens are not
blocked
match local AC voltage and
39
and correct if necessary
Productcode: 40280
Infinity XPLO-15 LED Strobe
Model:
Infinity XPLO-15 LED Strobe
Input Voltage:
100-240 VAC, 60/50Hz
Power consumption:
132W (full output)
DMX linking:
30pcs
Dimensions:
319 x 130 x 255 mm (LxWxH)
Weight:
5,4 kg
Operating and Programming:
Signal pin OUT:
Pin 1 (earth), pin 2 (-), pin 3 (+)
DMX Mode:
1, 3, 4, 6, 28 Channels
Signal input:
3-pin DMX/RDM IN
Signal output:
3-pin DMX/RDM OUT
Electro-mechanical effects:
Light Source:
576 x 6500K Luxeon SMD
Output:
28000 lux
Color mixing:
White
Color temperature:
6500K
Beam angle:
115°
Dimmer:
0-100%
Strobe:
0,5-30Hz
Dimming Curves:
Dimming curves: Linear, PL-Curve, S-Curve, SquareCurve
Housing:
Metal & Flame retardant plastic
IP rating:
IP54
DMX-control:
via standard DMX/RDM controller
On Board:
LCD display with gravity sensor
Control:
Stand-alone, Master/Slave, DMX
Connections:
Dedicated Schuko to Neutrik True1 & Data connector
Max. ambient temper ature ta:
40°C
Max. housing temperature tB:
80°C
Minimum distance:
Minimum distance from flammable surfaces:
0,5 m
Minimum distance to lighted object:
1 m
Product Specifications
Design and product specifications are subject to change without prior notice.
Website:
Email: service@highlite.nl
40
www.Showtec.info
Productcode: 40280
Infinity XPLO-15 LED Strobe
Dimensions
41
Productcode: 40280
Infinity XPLO-15 LED Strobe
Notes
42
©2015 Infinity
Loading...