Indesit K 642 G-G, K 645 G-G, K 645R G-G, K 642 GS-G, K 647R G-G, K 643 G-G, K 6432 G-G, K 642R GS-G, K 647 GS-G User Manual
Cooker with gas oven
and gas grill
Instructions for installation and use
K 642 G/G
K 642 GS/G
K 642R GS/G
K 643 G/G
K 6432 G/G
K 645 G/G
K 645R G/G
K 647 GS/G
K 647R G/G
Cooker with gas oven and gas grill
Instructions for installation and use
Important safety warnings
T o maintain the EFFICIENCY and SAFETY of this appliance, we recommend:
•use only the MANUFACTURER Service
•use only ORIGINAL Spare Parts
1This owner's manual is for a class 1 appliance (installed
independently) or class 2 - sub-class 1 appliances (installed
between two cabinets).
2Before using the appliance, read the instructions in this
owner’s manual carefully since you should find all the
instruction you require to ensure safe installation, use and
maintenance.
Always keep this owner’s manual close to hand since y ou
may need to refer to it in the future.
3When you hav e removed the packing, chec k that the appliance
is not damaged. If you have any doubts, do not use the appliance ,
contact your nearest Ariston Service Centre. Never leave the
packing components (plastic bags, foamed polystyrene, nails,
etc.) within the reach of children since they are a source of
potential danger.
4The appliance must be installed only by a qualified person in
compliance with the instructions provided. The manufacturer
declines all responsibility for improper installation which may
harm persons and animals and damage property.
5The electrical safety of this appliance can only be guaranteed if
the cooker is correctly and efficiently earthed, in compliance
with current regulations on electrical safety . Always ensure that
the earthing is efficient; if you hav e any doubts call in a qualified
electrician to check the system. The manufacturer declines all
responsibility for damage resulting from a system which has
not been earthed.
6Before connecting the appliance to the mains, check that the
specifications indicated on the rating plate correspond to those
of the electrical mains system of your home.
7The cooker must be connected to the mains electrical supply
via a earthed 13 or 15 amp. soc ket outlet, meeting the electrical
current requirements detailed under “electrical Connection” in
the installation section later in this book.
8The openings and slots used for ventilation and dispersion of
heat on the rear and below the control panel must never be
covered.
9This appliance must be used for the purpose for which it was
expressly designed. Any other use (e.g. heating rooms) is
considered to be improper and consequently dangerous. The
manufacturer declines all responsibility for damage resulting
from improper and irresponsible use.
10 A number of fundamental rules must be followed when using
electrical appliances. The follo wing are of particular importance:
•do not touch the appliance when your hands or feet are wet
•do not use the appliance barefooted
•never allow the Mains Cable to be stretched, pulled or
damaged if the Cooker is moved for cleaning etc. Do not
use the cooker if the Mains Cable is damaged, consult a
qualified electrician.
•do not allow the cooker to be used unsupervised by children
or persons unfamiliar with it.
11 Always s witch off the electrical supply to the cooker and allow it
to cool down before carrying out any cleaning operations etc.
12 In the case of faults and/or faulty operation, switch off the
electricity supply to the cooker and do not tamper with it. For
repairs call only an authorised after-sales servicing centre and
request the use of original spare parts only. Failure to comply
with the above may compromise the saf ety of the appliance .
13 Remember if you are discarding any domestic appliance with
which children etc. may play , make it saf e by removing the Mains
Cable from it, after first disconnecting the electricity supply.
Remove glass parts where possible, and consider sharp edges
etc. which ma y no w be exposed.
14 Oven glov es or similar protection should be used when moving
containers in or out of hot ovens and care should be be tak en to
avoid contact with hot surfaces by exposed skin on wrists or
arms.
15 One of the commonest types of accident involving cooking
appliances is burns to babies and young children. These can
occur by:
a) Touching hot parts
b) Being splashed with hot liquids
c) By pulling projecting pan handles and tipping hot liquids
over themselves
16 Please remember that a small child’s skin is f ar more sensitive
and therefore easily burnt. You are, therefore, strongly advised
to keep babies and young children well clear of this appliance
during use and whilst it is cooling down after use.
17 Unstable or out of shape pans should not be used on the hob in
case they cause spillage of hot liquids by tipping o ver .
18 Pans must only be placed in the centre of the b urners. Placing
pans off centre may cause cooking irregularites.
19 Special care should be taken when using chip pans etc. in order
to avoid splashing or spillage of hot oil. The y should not be used
unattended since overheated oil may boil over and could also
ignite.
20 Parts of this appliance, cooking surfaces, retain heat for
considerable periods after switching off. Care should, therefore ,
be taken when touching these areas before they ha ve completely
cooled down.
21 Remember to keep c hildren away from the appliance when
you use the grill or oven, since these parts become very
hot.
22 Never use flammable liquids such as alcohol or gasoline, etc.
near the appliance when it is in use.
23 Wear oven gloves when placing coockware in the oven or
removing it.
24 Never use the o v en as place to store flammable material.
25 When using small electric appliances near the hob, keep the
supply cord awa y from the hot parts.
26 Make sure the knobs are in the “•”/”O” position when the appliance
is not in use.
27 Warning: open the door with care since if you are not careful
you may hurt yourself in the hinge area.
28 Gas units need a regular air replacement for a correct
functioning. Make sure that the requirements requested in
the “Positioning” paragraph are all observed in the owner’ s
manual.
29 If the cooker is placed on a pedestal, take the necessary
precautions to prevent the same from sliding off the pedestal
itself.
3
Installation
HOOD
420
Min.
min.
650
mm. with hood
min.
700
mm. without hood
mm.
600
Min.mm.
420
Min.mm.
HOT PARTS
The following instructions should be read by a qualified technician
to ensure that the appliance is installed, regulated and technically
serviced correctly in compliance with current regulations.
Important: remember to unplug the appliance from the
mains before regulating the appliance or carrying out any
maintenance work.
Positioning
Important: this unit may be installed and used only in permanently
ventilated rooms according to the British Standards Codes Of
Practice: B .S. 6172/B.S. 5440, Par. 2 and B.S . 6891 Current Editions.
The following requirements must be observed:
a) The cooker should not be installed in a bed sitting room with a
volume of less than 20m3. If it is installed in a room of v olume
less than 5m3 an air vent of eff ective area of 110cm2 is required,
if it is installed in a room of volume between 5m3 and 10m3 a
supplementary airvent area of 50cm2 is required, if the volume
exceeds 11m3 no airvent is required. Ho wever , if the room has
a door or a window which opens directly to the outside no air
vent is required even when the volume is between 5m3 and
11m3.
b) During prolonged use of the appliance you may consider it
necessary to open a window to the outside to improve ventilation.
c) If there are other fuel burning appliances in the same room,
B.S.5440 Part 2 Current Edition, should, be consulted to
determine the requisite air vent requirements.
of the cooker the following precautions m ust be followed:
a) The cooker may be located in a kitchen, a kitonen/diner or
bed sitting room, but not in a bathroom or shower room.
b) The furniture units next to the cooker , that is higher than the
working boards, must be placed at least 110mm from the
edge of the board. Curtains must not be fitted immediately
behind the cooker or within 110 mm. of the sides of the cooker.
c) The hoods must be installed according to the requirements
in the hood handbook.
d) Wall cabinets may be fitted in line with the sides of the base
units, providing that the lower edge of the wa ll cabinet is a
minimum of 420 mm. above the worktop. The minimum
distance combustible material kitchen units can be fitted
directly above the worktop is 700 mm (Fig. A).
e) The wall in contact with the back of the cooker must be of
flameproof material.
f) The cooker is fitted with a safety chain that must be attached to
a hook, secured to the wall behind the appliance.
Note: some models can have their gas connection inv erted.
It is important to make sure the safety chain is always situated
on the side which corresponds to the hose holder (Fig. B).
Levelling your appliance (only on a f ew models)
Your cooker is supplied with feet for levelling the appliance. If
necessary , these f eet can be scre wed into the housings in the
corners of the cooker base.
Mounting the legs (only on a few models)
Press-fit legs are supplied which fit under the base of your cooker .
Fig. AFig. B
Gas connection
The cooker should be connected to the gas-supply by a corgi
registered installer. During installation of this product it is essential
to fit an approved gas tap to isolate the supply from the appliance
for the convenience of any subsequent removal or servicing.
Connection of the appliance to the gas mains or liquid gas must
be carried out according to the prescribed regulation in force,
and only after it is ascertained that it is adaptable to the type of
gas to be used. If not, follow the instructions indicated in the
paragraph headed “Adaptation to diff erent gas types”. On some
models the gas supply can be connected on the left or on the
right, as necessary; to change the connection, reverse the position
of the hose holder with that of the cap and replace the gasket
(supplied with the appliance). In the case of connection to liquid
gas, by tank, use pressure regulators that conform to the
regulation in force. The gas supply must be connected to the left
of the appliance. Be sure that the hose does not pass through
the rear of the cooker touching hot parts.
Installation of the cooker
The cooker is prepared with protection degree against e xcessive
heating of type X, the appliance can therefore be installed next
to cabinets, provided the height does not e xceed that of the hob.
If the cooker is placed touching walls or sides of neighbouring
cabinets, these must be capable of withstanding a temperature
rise of 50°C above room temperature. F or a correct installation
4
Important: make sure the supply pressure conforms with the values
GREEN &
YELLOW
BROWN
BLUE
13 amp fuse
CROSS-BAR
CORD GRIP
shown in the table entitled “Caracteristics of the burners and nozzles”.
When the cooker is installed between cabinets (recessed),
the gas connection must be effected by an appr oved flexible
hose with bayonet fitting (BS 669 Current Edition). The gas
inlet for the cookers is a threaded G 1/2 gas female fitting.
Connecting the gas supply
To make the connection, a flexible hose should be used
corresponding to the current gas regulations which are:
•the hose must never be at an y point in its lenght in contact with
the “hot” parts of the cooker;
•the hose must nev er be longer than 1,5 metre;
•the hose must not be subject to any tension or torsional stress
and it must not have any excessively narrow curves or
bottlenecks;
•the hose must be easy to inspect along its entire length to check
its condition;
•the hose must always be in good condition, never attempt to
repair.
Important: the installation must comply with gas safety (installation
and use) regulations 1984. In all cases for the above, by low, a
qualified, corgi approved engineer must be called f or installation.
Electrial connection
Po wer supply voltage and frequency: 230-240V a.c. 50 Hz.
Note: the supply cable must be positioned so that it ne ver reaches
at any point a temperature 50°C higher than the room temperature.
The cable must be routed away from the rear vents. Should you
require it, you may use a longer cab le, howe ver , you must ensure
that the cable supplied with the appliance is replaced by one of the
same specifications in accordance with current standards and
legislation.
Your appliance is supplied with a 13 amp fused plug that can be
plugged into a 13 amp socket f or immediate use. Bef ore using the
appliance please read the instructions below.
WARNING - THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERA TIONS SHOULD BE CARRIED OUT
BY A QUALIFIED ELECTRICIAN.
the mains cable must be wired into a cooker output point with a
rating of 45 amp. In this case the cable is not supplied.
Disposing of the plug:
Ensure that before disposing of the plug itself, y ou make the pins
unusable so that it cannot be accidentally inserted into a socket.
Instructions for connecting cable to an alternative plug:
Important: the wires in the mains lead are coloured in accordance
with the following code:
Green & Yellow- Earth
Blue- Neutral
Brown- Live
If the colours of the wires in the mains lead do not correspond with
the coloured markings identifying the terminals in your plug, proceed
as follows:
Connect Green & Yellow wire to terminal marked “E” or or
coloured Green or Green & Yellow.
Connect Brown wire to terminal marked “L” or coloured Red.
Connect Blue wire to terminal marked “N” or coloured Blac k.
If a 13 amp plug (BS 1363) is used it must be fitted with a 13 amp
fuse. A 15 amp plug must be protected by a 15 amp fuse, either in
the plug or adaptor or at the distribution board. If you are in any
doubt about the electrical supply to your machine, consult a qualified
electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in accordance with the
following code:
BLUE“NEUTRAL” (“N”)
BRO WN“LIVE” (“L”)
GREEN AND YELLO W“EARTH” (“E”)
Replacing the fuse:
When replacing a faulty fuse, a 13 amp AST A appro ved fuse to BS
1362 should always be used, and the fuse cov er re-fitted. If the fuse
cover is lost, the plug must not be used until a replacement is obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the correct colour
as indicated by the coloured marking or the colour that is embossed
in words on the base of the plug. Replacements can be obtained
directly from your nearest Service Depot.
Removing the plug:
If your appliance has a non-rewireable moulded plug and y ou should
wish to remove it to add a cable e xtension or to re-route the mains
cable through partitions, units etc., please ensure that either:
•the plug is replaced by a fused 13 amp re-wireable plug bearing
the BSI mark of approval.
or:
•the mains cable is wired directly into a 13 amp cable outlet,
controlled by a switch, (in compliance with BS 5733) which is
accessible without moving the appliance.
Please note: for appliances with a rating greater than 13 amp (eg:
electric hob, double o vens and freestanding electric cookers etc.)
Disposing of the appliance
When disposing of the appliance please remove the plug by cutting
the mains cable as close as possible to the plug body and dispose
of it as described above.
Adapting the cooker to different types of gas
In order to adapt the cooker to a different type of gas with respect
to the gas for which it was produced (indicated on the label
attached to the lid), follow these steps:
a) replace the hose holder mounted on the appliance with that
supplied in the bag of “cooker accessories”.
Important: the hose holder for liquid gas is marked 8, the hose
holder for methane gas is marked 13. Always fit the sealing
gasket.
b) Replacing the burner nozzles on the hob:
•remov e the grids and slide the burners from their housings;
•unscrew the nozzles using a 7 mm socket spanner, and
replace them with nozzles for the new type of gas (see tab le
1 “Burner and nozzle characteristics”).
•replace all the components by repeating the steps in rev erse
order.
5
Loading...
+ 11 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.