Indesit IDL 505 User Manual

IDL 500
IDL 505
Dishwasher
Installation and use
Safety Is a Good Habit to Get Into
NOTICE Carefully read the instructions contained in this manual, as they provide important information which is essential to safe and proper installation, use and maintenance of the appliance.
This appliance complies with the following EEC directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications;
- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications.
- 97/17/EEC Labelling
1.Carefully dispose of the packing material.
2.After removing the packing, check to make sure that
the appliance is not damaged. If in doubt, contact a qualified professional.
3.The dishwasher must only be used by adults for the washing of household dishes and cooking utensils.
4.Fundamental rules to follow when using the appliance:
- Never touch the dishwasher when barefoot or with wet hands or feet;
- We discourage the use of extension cords and multiple sockets;
- During installation, the power supply cord must not be excessively or dangerously bent or flattened;
- If the appliance is not operating properly or maintenance
must be performed, disconnect the appliance from the power supply .
5.Keep detergents out of the reach of children, who must also be kept away from the dishwasher when it is open.
6.This appliance cannot be installed outdoors, not even if the area in which it is installed is covered by a roof; it is also very dangerous to leave it exposed to the rain and elements.
7.Do not touch the heating element during or after a wash cycle.
8.Do not lean or sit on the door when it is open, as this could overturn the dishwasher .
9.If the appliance malfunctions, turn off water supply to the appliance and disconnect the plug from the wall socket. Then, consult the section entitled, "T roubleshooting." If you cannot resolve the problem, contact a service centre.
10.Appliances which are no longer being used must be made inoperable by cutting the power supply cord and removing the door lock.
To maintain the EFFICIENCY and SAFETY of this appliance, we recommend:
l call only the Service Centers authorized
by the manufacturer
l always use original Spare Parts
Close-up View (control panel)
G
Time 4 You
Intensive
Rapid
C
ON - OFF Button
ON - OFF Light
R
Eco
Soak
5
D
Knob For Selecting Cycles
Cycle phase indicator lights
A
B
Handle For Opening Door
Start/Reset Button
1
GB
Close-up View (Interior)
G
J
I
E
F
H
K
L
Upper Rack
T op Sprayer Arm
Rack Height Adjustor
Lower Rack
Widt h cm. 60 Depth cm. 60 Height cm. 85
Capacity 12 standard place settings
Mains water pressure 30 KPa÷ 1MPa (0,3 ÷10 bar)
Power voltage See data plate Total absorber power See data plate Fuse See data plate
Bottom Sprayer Arm
Salt Container Cap
Washing Filter
Detergent and Rinse Aid Dispenser
7 HFKQ LFDO FKDU DFWHUL VWLFV
GB
2
Salt ......
Salt
The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils. The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water.
Loading the Salt into the Softener
Always use salt intended for use with dishwashers. The salt container is located beneath the lower rack and should be filled as follows:
1. Remove the lower rack and then unscrew and remove the cap from the salt container;
2. If you are filling the container for the first time, fill it with water;
3. Place the end of the funnel (supplied) into the hole and introduce about 2 kg of salt. It is normal for a small amount of water to come out of the salt container.
4. Carefully screw the cap back on.
The salt container should be filled after about every 30 wash cycles.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjusting the amount of salt consumed based on the harness of the water used. This is intended to optimize and customize the level of salt consumption so that it remains at a minimum. Your Local Water Board can supply the degree of hardness of the water in your area. T o adjust salt consumption, pro­ceed as follows:
1) Unscrew the cap from the salt container.
2) There is a ring on the container with an arrow on it (see figure to the side), if necessary, rotate the ring in the anti­clockwise direction from the "_" setting towards the "+" sign, based on the hardness of the water being used. It is recommended that adjustments be made in accord­ance with the following schema:
Water Hardness
Salt
Autono­my
(cycles\2­kg)
Clarke
degrees
°fH mmol/l
Selector position
consu­mption
(grams/­cycle)
Warning: To prevent rust from forming, we advise you to load the salt before starting a wash cycle.
0 - 14 0 - 17 0 -1,7 / 0 /
14 - 36 18 - 44 1,8 - 4,4 "-" 20 60
36 - 71 45 - 89 4,5 - 8,9 MED 40 40
>71 > 89 > 8,9 "+" 60 25
3
GB
Loading...
+ 11 hidden pages