Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Description of the washing machine, 6-7
Control panel
Display
Running a wash cycle, 8
GB
Wash cycles and options, 9
Table of wash cycles
Wash options
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Fast daily cycles
Special wash cycles
Load balancing system
Troubleshooting, 11
Service, 12
1
Installation
GB
! This instruction manual should be kept in a safe
place for future reference. If the washing machine
is sold, transferred or moved, make sure that the
instruction manual remains with the machine so
that the new owner is able to familiarise himself/
herself with its operation and features.
! Read these instructions carefully: they contain
vital information relating to the safe installation
and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has not
been damaged during the transportation process.
If it has been damaged, contact the retailer and do
not proceed any further with the installation process.
3. Remove the 3 protective screws (used
during transportation)
and the rubber washer
with the corresponding
spacer, located on the
rear part of the appliance (see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will need
them again if the washing machine needs to be
moved to another location.
Levelling the machine correctly will provide it with
stability, help to avoid vibrations and excessive
noise and prevent it from shifting while it is operating. If it is placed on carpet or a rug, adjust the
feet in such a way as to allow a sufficient ventilation space underneath the washing machine.
Connecting the electricity and water supplies
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it to
a cold water tap using
a ¾ gas threaded connection (see figure).
Before performing the
connection, allow the
water to run freely until
it is perfectly clear.
2. Connect the inlet
hose to the washing
machine by screwing
it onto the corresponding water inlet of the
appliance, which is situated on the top righthand side of the rear
part of the appliance
(see figure).
3. Make sure that the hose is not folded over
or bent.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing machine on a flat sturdy
floor, without resting it up against walls, furniture
cabinets or anything else.
2. If the floor is not perfectly level, compensate for any unevenness
by tightening or loosening the adjustable
front feet (see figure);
the angle of inclination,
measured in relation to
the worktop, must not
exceed 2°.
2
! The water pressure at the tap must fall within
the values indicated in the Technical details table
(see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
65 - 100 cm
Connecting the drain hose
Con nect the drain
hose, without bending
it, to a drainage duct or
a wall drain located at a
height between 65 and
100 cm from the floor;
Alternatively, place the
drain hose over the
edge of a washbasin or
bathtub, by fastening
the guide (which
can be purchased at
the technical assistance centre) to the tap
(see figure). The free
end of the hose should
not be underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose and
must not exceed 150 cm in length.
Electrical connections
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be replaced
by authorised technicians.
Warning! The company shall not be held responsible
in the event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before you use it for the first time, run a wash cycle
with detergent and no laundry, using the wash
cycle “Auto Clean” (see “Cleaning the washing
machine”).
Technical data
Model
Dimensions
Capacity
Electrical
connections
EWE 61252
width 59.5 cm
height 85 cm
depth 51,7 cm
from 1 to 6 kg
please refer to the technical
data plate fixed to the machine
GB
Before plugging the appliance into the electricity
socket, make sure that:
indicated in the Technical data table (see opposite);
•thesocketiscompatiblewiththeplugofthe
washing machine. If this is not the case, replace the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to
rain, storms and other weather conditions.
! When the washing machine has been installed,
the electricity socket must be within easy reach.
Water
connection
Spin speed
Test wash
cycles in
accordance
with regulations
1061/2010
and
1015/2010
This will limit wear on the hydraulic system
inside the washing machine and help to prevent leaks.
•Unplugthewashingmachinewhencleaning
it and during all maintenance work.
Cleaning the washing machine
•Theouter partsand rubber componentsof
the appliance can be cleaned using a soft cloth
soaked in lukewarm soapy water. Do not use
solvents or abrasives.
• Thewashingmachinehasa “Auto Clean”
programme for its internal parts that must be
run with no load in the drum.
For maximum performance you may want to
use either the detergent (i.e. a quantity 10% the
quantity specified for lightly-soiled garments) or
special additives to clean the washing machine.
We recommend running a cleaning programme
every 40 wash cycles.
To start the programme press buttons A and B
simultaneously for 5 seconds (see figure).
The programme will start automatically and will
last approximately 70 minutes.
Caring for the door and drum of
your appliance
•Alwaysleavetheportholedoorajarinorder
to prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning pump which does not require any maintenance. Sometimes, small items (such as coins
or buttons) may fall into the pre-chamber which
protects the pump, situated in its bottom part.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. using a screwdriver, remove the cover
panel on the lower
front part of the washing machine (see figure);
A
B
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and pulling
it out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
2. unscrew the lid
by rotating it anticlockwise (seefigu-re): a little water may
trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
4
Precautions and tips
! This washing machine was designed and constructed in
accordance with international safety regulations. The following information is provided for safety reasons and must
therefore be read carefully.
from 8 years and above and persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Children
shall not play with the appliance. Cleaning
and user maintenance shall not be made by
children without supervision.
the appliance it must be separately collected. Consumers
should contact their local authority or retailer for information
concerning the correct disposal of their old appliance.
GB
Disposal
•Disposingofthepackagingmaterials:observelocalregulations so that the packaging may be re-used.
•TheEuropeanDirective2012/19/EU-WEEEonWasteElectrical and Electronic Equipment, requires that old household
electrical appliances must not be disposed of in the normal
unsorted municipal waste stream. Old appliances must
be collected separately in order to optimise the recovery
and recycling of the materials they contain and reduce the
impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product
reminds you of your obligation, that when you dispose of
5
GB
Description of the washing
machine
Control panel
Button with indicator light
KEYPAD LOCK
ON/OFF
button
Detergent dispenser drawer
WASH CYCLE
Detergent dispenser drawer: used to dispense detergents and washing additives (see “Detergents and laundry”).
ON/OFF button : press this briefly to switch the machine
on or off. The START/PAUSE indicator light, which flashes
slowly in a green colour shows that the machine is switched
on. To switch off the washing machine during the wash cycle,
press and hold the button for approximately 2 seconds; if
the button is pressed briefly or accidentally the machine will
not switch off. If the machine is switched off during a wash
cycle, this wash cycle will be cancelled.
WASH CYCLE knob: used to set the desired wash cycle
(see “Table of wash cycles”).
OPTION buttons with indicator light: used to select the
available options. The indicator light corresponding to the
selected option will remain lit.
Button with indicator light KEYPAD LOCK : This option
locks the control panel (except for the ON/OFF button) in
order to prevent both children from changing the washingmachine settings while in operation and any involuntary
starting. Press it for at least 2 seconds to enable/disable it.
TEMPERATURE
Button
knob
TEMPERATURE button : press to decrease or completely exclude the temperature: the value will be shown on the
display.
DELAYED START button : press to set a delayed start
time for the selected wash cycle. The delay time will be shown
on the display.
START/PAUSE button with indicator light: when the
green indicator light flashes slowly, press the button to start
a wash cycle. Once the cycle has begun the indicator light
will remain lit in a fixed manner. To pause the wash cycle,
press the button again; the indicator light will flash in an
orange colour. If the symbol is not illuminated, the door
may be opened (wait approximately 3 minutes). To start the
wash cycle from the point at which it was interrupted, press
the button again.
Standby mode
This washing machine, in compliance with new energy saving
regulations, is fitted with an automatic standby system which
is enabled after about 30 minutes if no activity is detected.
Press the ON-OFF button briefly and wait for the machine
to start up again.
OPTION
buttons with
indicator lights
SPIN SPEED
Button
DISPLAY
START/PAUSE
button with indicator light
DELAYED
START Button
SPIN button : press to reduce or completely exclude the
spin cycle - the value is indicated on the display.
6
Display
GB
B
CA
The display is useful when programming the machine and provides a great deal of information.
The duration of the available programmes and the remaining time of a running cycle appear in section A; if the DELAY START
option has been set, the countdown to the start of the selected programme will appear. Pressing the relative button, the
machine automatically displays the maximum temperature and spin speed values set for the selected cycle, or the most
recently-used settings if they are compatible with the selected cycle.
The “programme phases” relative to the selected programme and the “programme phase” of the running programme appear
in section B:
Wash
Rinse
Spin
Drain
The icons corresponding to “temperature” , “Programmed start” and “spin” appear in section C from top to bottom:
If the symbol lights up, the display will visualise the set “temperature” value.
When a “delayed start” has been set, the symbol lights up.
If the symbol lights up, the display will visualise the set “spin” value.
Door locked symbol
The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the
door.
To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched
off the door may be opened (wait approximately 3 minutes).
7
Running a wash cycle
GB
1. SWITCH THE MACHINE ON. Press the button;
the START/PAUSE indicator light will flash slowly in a
green colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent into
the relevant compartments as described in “Detergents
and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Set the WASH CYCLE
knob to the desired programme; a temperature and spin
speed is set for each wash cycle; these may be adjusted.
The duration of the cycle will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modifying the temperature and/or spin
speed. The machine automatically displays the
maximum temperature and spin speed values set for
the selected cycle, or the most recently-used settings
if they are compatible with the selected cycle. The
temperature can be decreased by pressing the
button, until the cold wash “OFF” setting is reached.
The spin speed may be progressively reduced by
pressing the button, until it is completely excluded
(the “OFF” setting). If these buttons are pressed again,
the maximum values are restored.
! Exception: if the 4 programme is selected, the tempe-
rature can be increased up to a value of 60°C.
! The options may affect the recommended load value
and/or the duration of the cycle.
7. START THE PROGRAMME. Press the START/
PAUSE button. The corresponding indicator light will
become green, remaining lit in a fixed manner, and the
door will be locked (the DOOR LOCKED symbol will
be on). To change a wash cycle while it is in progress,
pause the washing machine using the START/PAUSE
button (the START/PAUSE indicator light will flash
slowly in an orange colour); then select the desired
cycle and press the START/PAUSE button again.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened (wait
approximately 3 minutes). Press the START/PAUSE
button again to restart the wash cycle from the point at
which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when the
DOOR LOCKED symbol switches off the door may be
opened (wait approximately 3 minutes). Open the door,
unload the laundry and switch off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the button. The cycle will be stopped
and the machine will switch off.
Setting a delayed start.
To set a delayed start for the selected programme,
press the corresponding button repeatedly until the
required delay period has been reached. When this
option is enabled, the symbol lights up on the
display. To remove the delayed start option press the
button until the text “OFF” appears on the display.
Modifying the cycle settings.
• Press the button to enable the option; the indicator
light corresponding to the button will switch on.
• Press the button again to disable the option; the
indicator light will switch off.
! If the selected option is not compatible with the
programmed wash cycle, the indicator light will flash
and the option will not be activated.
! If the selected option is not compatible with another
option which has been selected previously, the indicator
light corresponding to the first option selected will flash
and only the second option will be activated; the indicator
light corresponding to the enabled option will remain lit.
8
Wash cycles and options
Extra Wash
Extra Wash
Table of wash cycles
Description of the wash cycle
Wash cycles
EVERYDAY FAST
1 Colour Mix 59’
2 Cotton 59’
3 Cotton 45’
4 Synthetics 59’ (3)
5 Mix 30’
6 Express 20’
Special & Partial
7 Gym Kit
8 Sport Shoes
9
Baby: Heavily soiled delicate colours.40° 800-
10 Rinse
11 Spin + Drain
11 Only Drain *
Dedicated
12
Duvet: for down-stuffed garments.30°1000-
13
Wool: for wool, cashmere, etc.40° 800-
14
Silk/Curtains: for garments in silk and viscose, lingerie.
15
Eco Cotton 60° (1): heavily soiled whites and resistant colours.60°1200-
15
Eco Cotton 40° (2): lightly soiled whites and delicate colours.40°1200-
16
Cotton with prewash: extremely soiled whites. 90°1200
Max.
temp.
(°C)
40°100060°100040°1200-
40°
(Max. 60°)
30°80020°800-
40°600-
30°600-
30° 0-
Max.
speed
(rpm)
1000-
-1200--
-1200---
-OFF---
Pre-washWash
Detergents
Fabric
softener
Max.
Residual
load (kg)
---59’
6
---59’
6
---45’
3
440,5039 59’
3
700,1731 30’
3
---20’
3
---**
3
Max.
---**
2 pairs
---**
2
---**
6
---**
6
---**
6
---**
1,5
---**
1,5
---**
1
530,93 50,0 190’
6
530,8576 170’
6
---**
6
Energy
dampness %
kWh
Total water lt
consumption
* If you select programme 11 and exclude the spin cycle, the machine will drain only.
** The duration of the wash cycle can be checked on the display.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as
water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
1) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 15 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 15 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle 15 with a temperature of 40°C.
3) Long programme for synthetics: set programme 4, then select the “
” option.
Cycle
duration
GB
Wash options
- If the selected option is not compatible with the
programmed wash cycle, the indicator light will flash and
the option will not be activated.
- If the selected option is not compatible with another
option which has been selected previously, the indicator
light corresponding to the first option selected will flash and
only the second option will be activated; the indicator light
corresponding to the enabled option will remain lit.
Enable the
compatible. Press this option to let the cycle automatically readjust all wash parameters through a longer lasting cycle. The
option always leaves the temperature unchanged, while the spin
cycle is automatically brought back to maximum levels. The user
can set the spin cycle back to the desired value at any time.
option for very dirty items, where
Extra Rinse
By selecting this option, the efficiency of the rinse is increased
and optimal detergent removal is guaranteed. It is particularly
useful for sensitive skin.
The option washes cotton and synthetic items,
saving energy and helping the environment. Energy saving
is due to a cold wash cycle, while an enhanced mechanical
action and optimised water use make it possible to reach the
desired result. Recommended for slightly soiled garments.
Use of liquid detergent recommended.
9
Detergents and laundry
1
2
3
GB
Detergent dispenser drawer
Good washing results also depend on the correct dose of
detergent: adding too much detergent will not necessarily
result in a more efficient wash, and may in fact cause build
up on the inside of your appliance and contribute to environmental pollution.
! Do not use hand washing detergents because these create
too much foam.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
Open the detergent dispenser drawer and pour in the
detergent or washing additive, as follows.
compartment 1: Pre-wash detergent (powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Note: If a “tablet detergent” is used, always follow the
manufacturer’s instructions.
Mix 30’: short cycle designed to wash a mixed load of cotton
and synthetic fabrics - white and coloured items together.
Express 20’: this programme refreshes your items, making
them perfumed again in just 20 minutes.
Special wash cycles
Gym Kit: cycle suitable to wash all sports items together,
including gym towels, while respecting their fibres (follow the
instructions in the garment labels).
Sport Shoes: is for washing sports shoes; for best results,
do not wash more than 2 pairs simultaneously.
We recommend fastening any strings before introducing the
shoes into the drum.
Baby: cycle designed for dirt typical of children’s garments
in that it effectively removes any traces of residual detergent.
Duvet: to wash single duvets (the weight of which should not
exceed 1,5 kg), cushions or clothes padded with goose down
such as puffa jackets, use the special wash cycle number 12.
We recommend that duvets are placed in the drum with their
edges folded inwards (see figure) and that no more than ¾
of the total volume of the drum is used. To achieve the best
results, we recommend that a liquid detergent is used and
placed inside the detergent dispenser drawer.
Preparing the laundry
•Dividethelaundryaccordingto:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
•Donotexceedthevalueslistedinthe“Table of wash
cycles”, which refer to the weight of the laundry when dry.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Fast daily cycles
A complete set of fast programmes to wash the most commonly used fabrics - even with a full load - and to remove
the most frequent daily dirt in less than 1 hour.
Colour Mix 59’: to wash mixed and coloured items together.
Cotton 59’: cycle designed to wash cotton garments - mainly
white items. It can be used with powder detergent too.
Cotton 45’: short cycle designed to wash delicate cotton items.
Synthetics 59’: specific for synthetic items. If the dirt is
difficult to remove, the temperature can be increased up to
60° and powder detergent can be used too.
Wool: all wool garments can be washed using programme
13, even those carrying the “hand-wash only” label. For
best results, use special detergents and do not exceed 1,5
kg of laundry.
Silk: use special wash cycle 14 to wash all silk garments.
We recommend the use of special detergent which has
been designed to wash delicate clothes.
Curtains: fold curtains and place them in a pillow case or
mesh bag. Use wash cycle 14.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load
is not balanced correctly, the machine spins at a reduced
spin speed. If the load is excessively unbalanced, the
washing machine performs the distribution process instead
of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are
mixed in the load.
10
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure
that the problem cannot be solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (“H2O” will flash on
the display).
The washing machine continuously
takes in and
drains water.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Assistance Service. If the dwelling is on one of
the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this inconvenience.
GB
The washing machine does not
drain or spin.
The washing machine vibrates a lot
during the spin cycle.
The washing machine leaks.
The “option” indicator lights and the
“start/pause” indicator light flash and
an error code appears on the display
(e.g.: F-01, F-..).
! Always request the assistance of authorised technicians.
Have the following information to hand:
• thetypeofproblem;
• theappliancemodel(Mod.);
• theserialnumber(S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
12
Bedienungsanleitungen
WASCHVOLLAUTOMAT
DE
Deutsch
EWE 61252
INHALTSVERZEICHNIS
Installation, 14-15
Auspacken und Aufstellen
Wasser- und Elektroanschlüsse
Erster Waschgang
Technische Daten
Reinigung und Pflege, 16
Abstellen der Wasser- und Stromversorgung
Reinigung des Gerätes
Reinigung der Waschmittelschublade
Pflege der Gerätetür und Trommel
Reinigung der Pumpe
Kontrolle des Wasserzulaufschlauchs
Vorsichtsmaßregeln und Hinweise, 17
Allgemeine Sicherheit
Entsorgung
Beschreibung Ihres Waschvollautomaten, 18-19
Bedienblende
Display
DE
Durchführung eines Waschprogramms, 20
Programme und Funktionen, 21
Programmtabelle
Waschfunktionen
Waschmittel und Wäsche, 22
Waschmittelschublade
Vorsortieren der Wäsche
Schnelle Tageszyklen
Sonderprogramme
Unwuchtkontrollsystem
Störungen und Abhilfe, 23
Kundendienst, 24
13
Installation
DE
! Es ist äußerst wichtig, diese Bedienungsanleitung sorgfältig aufzubewahren, um sie jederzeit
zu Rate ziehen zu können. Sorgen Sie dafür,
dass sie im Falle eines Umzugs oder einer Übergabe an einen anderen Benutzer das Gerät
stets begleitet, damit auch der neue Inhaber die
Möglichkeit hat, diese zu Rate zu ziehen.
! Lesen Sie die Hinweise bitte aufmerksam
durch, sie liefern wichtige Informationen hinsichtlich der Installation, des Gebrauchs und
der Sicherheit.
Auspacken und Aufstellen
Auspacken
1. Gerät auspacken.
2. Sicherstellen, dass der Waschvollautomat
keine Transportschäden erlitten hat. Im Falle einer Beschädigung Gerät bitte nicht anschließen,
sondern den Kundendienst anfordern.
3. Die 3 Transportschutz-schrauben herausschrauben und die an der
Geräterückwand
befindlichen Distanzstücke aus Gummi
entfernen (siehe Ab-bildung).
4. Die Öffnungen mittels der mitgelieferten
Abdeckungen verschliessen.
5. Sämtliche Teile aufbewahren: Sollte der
Waschautomat erneut transportiert werden,
müssen diese Teile wieder eingesetzt werden.
! Verpackungsmaterial ist kein Spielzeug für
Kinder.
Nivellierung
1. Der Waschvollautomat muss auf einem
ebenen, festen, schwingungsfreien Untergrund
aufgestellt werden ohne diesen an Wände, Möbel etc. direkt anzulehnen.
2. Sollte der Boden
nicht perfekt eben
sein, müssen die
Unebenheiten durch
An- bzw. Ausdrehen
der vorderen Stellfüße
ausgeglichen werden
(siehe Abbildung), der
auf der Arbeitsfläche
zu ermittelnde Neigungsgrad darf 2°
nicht überschreiten.
Eine präzise Nivellierung verleiht dem Gerät die
erforderliche Stabilität, durch die Vibrationen,
Betriebsgeräusche und ein Verrücken des
Gerätes vermieden werden. Bei Teppichböden
müssen die Stellfüße so reguliert werden, dass
ein ausreichender Freiraum zur Belüftung unter
dem Waschvollautomaten gewährleistet ist.
Wasser- und Elektroanschlüsse
Anschluss des Zulaufschlauches
1. Schrauben Sie den
Wasserschlauch an
einen Kaltwasserhahn
mit ¾-GAS-Gewindeanschluss an (siehe Abb.). Lassen Sie
das Wasser vor dem
Anschluss so lange
auslaufen, bis klares
Wasser austritt.
2. Das andere Ende
des Schlauches an
den oben rechts am
Rückteil des Waschvollautomaten befindlichen Wasseranschluss anschließen
(siehe Abbildung).
3. Der Schlauch darf hierbei nicht eingeklemmt
oder abgeknickt werden.
! Der Wasserdruck muss innerhalb der Werte liegen, die in der Tabelle der technischen
Daten angegeben sind (siehe nebenstehende
Seite).
! Sollte der Zulaufschlauch nicht lang genug
sein, dann wenden Sie sich bitte an einen
Fachhändler oder an einen autorisierten Fachmann.
! Verwenden Sie niemals bereits gebrauchte
Schläuche.
! Verwenden Sie die Schläuche, die mit dem
Gerät geliefert wurden.
14
Anschluss des Ablaufschlauches
65 - 100 cm
Schließen Sie den
Ablaufschlauch ohne
ihn dabei abzuknicken
an einen geeigneten
Abfluss an. Die Mindestablaufhöhe beträgt
65 - 100 cm (gemessen vom Boden), oder
hängen Sie diesen
mittels des Schlauchhalters gesichert in
ein Becken oder Wanne ein;
Oder hängen Sie den
Ablaufschlauch in ein
Becken oder eine
Wanne ein; befestigen
Sie ihn in diesem Falle
mittels der Führung
(beim Kundendienst erhältlich) an
dem Wasserhahn
(siehe Abbildung). Das
freie Ablaufschlauchen-
de darf nicht unter Wasser positioniert werden.
! Verlängerungsschläuche sollten nicht eingesetzt werden. Sollte dies unvermeidlich sein,
muss die Verlängerung denselben Durchmesser des Originalschlauchs aufweisen und darf
eine Länge von 150 cm nicht überschreiten.
Stromanschluss
Vor Einfügen des Netzsteckers in die Steckdose ist sicherzustellen, dass:
Waschvollautomaten kompatibel ist. Andernfalls muss der Netzstecker (oder die
Steckdose) ersetzt werden.
! Der Waschvollautomat darf nicht im Freien
installiert werden, auch nicht, wenn es sich
um einen geschützten Platz handelt. Es ist
gefährlich, das Gerät Gewittern und Unwettern
auszusetzen.
! Die Steckdose sollte nach installiertem Gerät
leicht zugänglich sein.
! Verwenden Sie bitte keine Verlängerungen oder
Mehrfachstecker.
! Das Netzkabel darf nicht gebogen bzw. eingeklemmt werden.
! Das Versorgungskabel darf nur durch autorisierte Fachkräfte ausgetauscht werden.
Achtung! Der Hersteller übernimmt keinerlei
Haftung, sollten diese Vorschriften nicht genau
beachtet werden.
Erster Waschgang
Lassen Sie nach der Installation bzw. vor erstmaligem Gebrauch erst einen Waschgang (mit Waschmittel) ohne Wäsche durchlaufen. Stellen Sie
hierzu das Waschprogramm „AUTO REINIGEN“
ein (siehe „Reinigung des Gerätes“).
Technische Daten
Modell
Abmessunge
Fassungsvermögen
Elektroanschlüsse
Wasseranschlüsse
Schleudertouren
Prüfprogramme
gemäß
der Vorschriften
1061/2010
und
1015/2010
Programm 15:
Eco Baumwolle 60°C.
Programm 15:
Eco Baumwolle 40°C.
Dieses Gerät entspricht den
folgenden EG-Richtlinien:
- EMC - 2014/30/EU (elektromagnetische Verträglichkeit) und
nachfolgenden Änderungen
- 2012/19/EU - WEEE
- LVD - 2014/35/EU (Niederspannung)
DE
15
Reinigung und Pflege
DE
Abstellen der Wasser- und Stromversorgung
• Drehen Sie den Wasserhahn nach jedem
Waschvorgang zu. Hierdurch wird der Verschleiß der Wasseranlage verringert und
Wasserlecks vorgebeugt.
• Ziehen Sie den Netzstecker aus der
Steckdose, bevor Sie Ihren Waschvollautomaten reinigen.
Reinigung des Gerätes
• Die Gehäuseteile und die Teile aus Gummi
können mit einem mit warmer Spülmittellauge
angefeuchteten Tuch gereinigt werden. Vermeiden Sie Löse- und Scheuermittel.
• Die Waschmaschine verfügt über ein „AUTO
REINIGEN“-Programm der inneren Teile, das gänzlich
ohne Wäsche durchgeführt werden muss.
Als Hilfsmittel können bei diesem Waschgang
Waschmittel (10 % von der für gering verschmutzte Kleidungsstücke empfohlenen Menge)
oder spezifische Zusatzstoffe für die Reinigung
von Waschmaschinen verwendet werden. Es
wird empfohlen, das Reinigungsprogramm alle
40 Waschgänge durchzuführen.
Um das Programm zu aktivieren, drücken Sie
fünf Sekunden lang gleichzeitig die Tasten A und B(siehe abb.). Das Programm startet automa-
tisch und dauert etwa 70 Minuten.
A
Pflege der Gerätetür und Trommel
• Lassen Sie die Gerätetür stets leicht offen stehen, um die Bildung unangenehmer Gerüche
zu vermeiden.
Reinigung der Pumpe
Ihr Gerät ist mit einer selbstreinigenden Pumpe
ausgerüstet, eine Wartung ist demnach nicht
erforderlich. Es könnte jedoch vorkommen, dass
kleine Gegenstände (Münzen, Knöpfe) in die
zum Schutz der Pumpe dienende Vorkammer
(befindlich unter der Pumpe) fallen.
! Vergewissern Sie sich, dass der Waschgang
abgeschlossen ist und ziehen Sie den Netzstecker heraus.
Zugang zur Vorkammer:
1. Nehmen Sie die
Abdeckung (befindlich
an der Gerätefront) mit
Hilfe eines Schraubenziehers ab (siehe Abbildung);
2. Drehen Sie den
Deckel gegen den
Uhrzeigersinn ab (sie-heAbbildung): es ist
ganz normal, wenn
etwas Wasser austritt;
B
Reinigung der Waschmittelschublade
Heben Sie die Schublade leicht an und
ziehen Sie sie nach
vorne hin heraus (sie-he Abbildung).
Spülen Sie sie regelmäßig unter fließendem Wasser gründlich
aus.
16
3. Reinigen Sie das Innere gründlich;
4. Schrauben Sie den Deckel wieder auf;
5. Bringen Sie die Abdeckung wieder an. Stellen
Sie hierbei sicher, dass die Haken in die Schlitze
eingreifen, bevor Sie die Abdeckung fest andrücken.
Kontrolle des Wasserzulaufschlauchs
Kontrollieren Sie den Zulaufschlauch mindestens
einmal im Jahr. Weist er Risse bzw. Brüche auf,
muss er ausgetauscht werden. Der starke Druck
während des Waschprogramms könnte zu plötzlichem Platzen führen.
! Verwenden Sie niemals bereits gebrauchte
Schläuche.
Vorsichtsmaßregeln und
Hinweise
! Der Waschvollautomat wurde nach den strengsten internationa-
len Sicherheitsvorschriften entworfen und gebaut. Nachstehende
Hinweise werden aus Sicherheitsgründen geliefert und sollten
aufmerksam gelesen werden.
Allgemeine Sicherheit
• Dieses Gerät wurde ausschließlich für den Einsatz im privaten
Haushalt konzipiert.
• Dieses Gerät darf von Kindern ab 8 Jahren
und von Personen mit eingeschränkten körperlichen, sensorischen oder geistigen Fähigkeiten oder mit unzureichender Erfahrung und
Kenntnis verwendet werden, vorausgesetzt,
sie werden überwacht oder sie haben eine
ausreichende Einweisung in die sichere Nutzung des Geräts erhalten und haben die damit
verbundenen Gefahren verstanden. Erlauben
Sie Kindern nicht, mit dem Gerät zu spielen.
Wartung und Reinigung dürfen nicht von unbeaufsichtigten Kindern ausgeführt werden.
• Berühren Sie das Gerät nicht, wenn Sie barfuß sind, und auch
nicht mit nassen oder feuchten Händen oder Füßen.
• Ziehen Sie den Gerätestecker nicht am Kabel aus der Steckdose, sondern nur am Netzstecker selbst.
• Öffnen Sie die Waschmittelschublade nicht, wenn das Gerät
in Betrieb ist.
• Berühren Sie nicht das Ablaufwasser, es könnte sehr heiß sein.
• Öffnen Sie die Gerätetür nicht mit Gewalt: Der Sicherheits-
Schließmechanismus könnte hierdurch beschädigt werden.
• Bei etwaigen Störungen versuchen Sie bitte nicht, Innenteile
selbst zu reparieren.
• Halten Sie Kinder stets von dem in Betrieb befindlichen Gerät
fern.
• Während des Waschgangs kann die Gerätetür sehr heiß
werden.
• Muss das Gerät versetzt werden, sollten hierfür zwei oder drei
Personen verfügbar sein. Versetzen Sie es niemals allein, das
Gerät ist äußerst schwer.
• Bevor Sie die Wäsche einfüllen, stellen Sie bitte sicher, dass
die Wäschetrommel leer ist.
Das Symbol „durchgestrichene Mülltonne“ auf jedem
Produkt erinnert Sie an Ihre Verpflichtung, dass Elektrohaushaltsgeräte gesondert entsorgt werden müssen. Endverbraucher können sich an Abfallämter der Gemeinden wenden, um mehr Informationen über die korrekte Entsorgung
ihrer Elektrohaushaltsgeräte zu erhalten.
DE
Entsorgung
• Entsorgung des Verpackungsmaterials: Befolgen Sie die loka-
len Vorschriften, Verpackungsmaterial kann wiederverwertet
werden.
• Gemäß der Europäischen Richtlinie 2012/19/EU - WEEE über
Elektro- und Elektronik-Altgeräte dürfen ElektrohaushaltsAltgeräte nicht über den herkömmlichen Haushaltsmüllkreislauf entsorgt werden. Altgeräte müssen separat gesammelt
werden, um die Wiederverwertung und das Recycling der
beinhalteten Materialien zu optimieren und die Einflüsse auf
die Umwelt und die Gesundheit zu reduzieren.
17
Beschreibung Ihres
Waschvollautomaten
DE
Bedienblende
Waschmittelschublade
Taste ON/OFF
Wählschalter
PROGRAMMWAHL
Taste
TEMPERATUR
Tasten mit
Kontrollleuchten
FUNKTIONEN
DISPLAY
Taste
SCHLEUDERN
Taste mit
Kontrollleuchte
TASTENSPERRE
Taste mit
Kontrollleuchte
START/
PAUSE
Taste
STARTZEITVORWAHL
Waschmittelschublade: für Waschmittel und Zusätze
(siehe „Waschmittel und Wäsche“).
Taste ON/OFF : Drücken Sie kurz auf die Taste, um das
Gerät ein- bzw. auszuschalten. Die Kontrollleuchte START/
PAUSE, die langsam grün blinkt, zeigt an, dass das Gerät
eingeschaltet ist. Um den Waschvollautomaten während
eines Waschgangs auszuschalten, muss die Taste etwas
länger gedrückt werden (ca. 2 Sekunden); ein kurzer oder
ein ungewollter Druck bewirkt kein Ausschalten des Gerätes.
Das Ausschalten des Gerätes während eines laufenden Waschprogramms löscht den gesamten Waschzyklus.
Wählschalter PROGRAMMWAHL: zur Einstellung des
gewünschten Programms (siehe “Programmtabelle”).
Tasten mit Kontrollleuchten FUNKTIONEN: Zur Einstellung
der verfügbaren Funktionen. Die der gewählten Einstellung
entsprechende Kontrollleuchte bleibt eingeschaltet.
Taste mit Kontrollleuchte TASTENSPERRE : Mit
dieser Option wird die Bedienblende (mit Ausnahme der
ON/OFF-Taste) blockiert und ist besonders nützlich, um zu
verhindern, dass Kinder die Einstellungen der Waschmaschine während des Betriebs verändern oder sie versehentlich
einschalten. Die Sperre wird durch Halten der Taste für mindestens 2 Sekunden ein- und ausgeschaltet.
Taste TEMPERATUR : Drücken Sie, um die Temperatur
herabzusetzen oder auszuschließen; der Wert wird auf dem
Display angezeigt.
Taste STARTZEITVORWAHL : Zur Vorwahl der Startzeit
des gewählten Programms drücken Sie bitte diese Taste. Die
Zeitverzögerung wird auf dem Display angezeigt.
Taste mit Kontrollleuchte START/PAUSE : Sobald die
grüne Kontrollleuchte auf langsames Blinklicht schaltet,
drücken Sie die Taste, um den Waschgang zu starten. Nach
Ingangsetzung des Programms schaltet die Kontrollleuchte
auf Dauerlicht. Um den Waschgang zu unterbrechen, drücken
Sie erneut die Taste; die Kontrollleuchte schaltet auf orangefarbenes Blinklicht. Wenn das Symbol nicht leuchtet,
kann die Gerätetür geöffnet werden (etwa 3 Minuten). Um
das Programm an der Stelle, an der es unterbrochen wurde,
wieder in Gang zu setzen, drücken Sie die Taste erneut.
Funktion Standby
Zur Erfüllung der neuen Richtlinien zum Energieverbrauch
ist diese Waschmaschine mit einem automatischen Ausschaltsystem (Standby) ausgestattet, das nach 30 Minuten
des Nichtgebrauchs in Funktion tritt. Drücken Sie kurz die
Taste ON/OFF und warten Sie, bis sich die Maschine wieder
einschaltet.
Taste SCHLEUDERN : Drücken Sie die Taste, um die
Schleudergeschwindigkeit herabzusetzen oder das Schleudern ganz auszuschließen. Der Wert wird auf dem Display
angezeigt.
18
Loading...
+ 42 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.