Impex MWM-981 Owner's Manual

NOTE:

Please read all instructions carefully before using this product

Table of Contents

Safety Notice

Hardware Pack

Assembly Instruction

Parts List

Resistance Chart

Warranty

Ordering Parts

Model

MWM-981

Retain This

Manual for

Reference

100322

OWNER'S

MANUAL

MARCY® MWM 981

HOME GYM

IMPEX® INC.

2801 S. Towne Ave., Pomona, CA 91766 Tel: [phone] Fax: [phone]

www.impex-fitness.com [e-mail]

TABLE OF CONTENTS

BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2

HARDWARE IDENTIFIER.....….....................................................................……….. 4 ASSEMBLY INSTRUCTIONS.........................................................................……….. 6 PARTS LIST…………………………………………………………………………………. 21

RESISTANCE CHART………….......................................................................………..22 WARRANTY.................................................................................................…………..23

ORDERING PARTS.......................................................................................………… 23

BEFORE YOU BEGIN

Thank you for selecting the MARCY MWM-981 HOME GYM by IMPEX® INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction. If you have any questions, or find there are missing or damaged parts, we guarantee you complete satisfaction through direct assistance from our factory. To avoid unnecessary delays, please call our TOLL-FREE customer service number. Our Customer Service Agents will provide immediate assistance to you.

Toll-Free Customer Service Number 1-800-999-8899

Mon. – Fri. 9 a.m. – 5 p.m. PST www.impex-fitness.com [e-mail]

1

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions:

1.Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine.

2.Only one person at a time should use the machine.

3.If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4.Position the machine on a clear, leveled surface. DO NOT use the machine near water or outdoors.

5.Keep hands away from all moving parts.

6.Always wear appropriate workout clothing when exercising. DO NOT wear robes or other clothing that could become caught in the machine. Running or aerobic shoes are also required when using the machine.

7.Use the machine only for its intended use as described in this manual. DO NOT use attachments not recommended by the manufacturer.

8.Do not place any sharp object around the machine.

9.Disabled person should not use the machine without a qualified person or

physician in attendance.

10.Before using the machine to exercise, always do stretching exercises to properly warm up.

11.Never operate the machine if the machine is not functioning properly.

12.A spotter is recommended during exercise.

13.Do not intend to insert weight selector pin while the weight stack or top plate is in elevated position.

14.Be certain the weight Selector Pin is completely inserted.

15.Never use dumbbells or other means to increase the weight resistance. Use only weight plates provided by manufacturer.

16.This machine is designed and intended for home and consumer use only, not for commercial use.

CARE AND MAINTENANCE

1.Lubricate moving parts with WD-40 or light oil periodically.

2.Inspect and tighten all parts before using the machine.

3.The machine can be cleaned using a damp cloth and mild non-abrasive detergent. DO NOT use solvents.

4.Maximum user’s weight: 300 lbs.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

2

WARNING LABEL REPLACEMENT

The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.

3

HARDWARE PACK

NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.

4

HARDWARE PACK

NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.

5

ASSEMBLY INSTRUCTION

Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that this machine to be assembled by two or more people to avoid possible injury.

STEP 1 (See Diagram 1)

A.) Insert the two Guide Rods (#11) through Rubber Bumpers and into the holes on the Rear Stabilizer. Secure each Guide Rod with one M10 x 1” Allen Bolt (#64) and

¾” Washer (#73) from the bottom. The Guide Rods has holes on the rod to lock the weight stack when not in use. The shorter end of the guide rod with the lock hole will need to be pointed downwards towards the Rear Stabilizer.

B.) Do not tighten all Nuts and Bolts starting from this procedure until instructed

to do so.

C.) Attach two Rubber Bumpers (#28) onto the holes onto the Guide Rods.

D.) Attach the Base Frame (#3) to the Rear Stabilizer. Secure them with two M10 x 4” Carriage Bolts (#59), one U-shaped Bracket (#20), two Ø ¾” Washers (#73), and two M10 Aircraft Nuts (#70).

E.) Attach the Vertical Frame (#4) onto the Base Frame. Secure them with two M10 x

2 3/8” Carriage Bolts (#58), one 1 ¾” x 4 ¾” Bracket (#18), two Ø ¾” Washers (#73), and two M10 Aircraft Nuts (#70).

F.) Slide 11 Weight Plates (#50) onto the Guide Rods. Make sure the deep grooves on the Weight Plates all face the back of the machine and downward. Align the holes on the Weight Plates. Insert a Selector Rod (#21) through the center hole. Slide the Selector Stem (#51) onto the Guide Rods.

G.) Use a Weight Selector Pin (#44) to select the number of Weight Plates to exercise.

	Attach the ring on Weight Selector Pin’s cable onto the Selector Rod. Note: Each
	Weight Plate weights approximately 10 lbs. Please refer to the Weight
	Resistance Chart in page 25.
H.)	Attach the Seat Support (#5) to the Vertical Frame. Secure it with two M10 x 2 3/8”
	Carriage Bolts (#58), one 1 ¾” x 4 ¾” Bracket (#18), two Ø ¾” Washers (#73), and
	two M10 Aircraft Nuts (#70).
I.)	Attach the Vertical Seat Support (#6) to Seat Support and Base Frame. Secure
	each end of Vertical Seat Support with two M10 x 1” Allen Bolts (#64) and two Ø
	¾” Washers (#73).

6

DIAGRAM 1

7