INSTALLATION INSTRUCTIONS
30" (76.2 CM) DOUBLE OVEN GAS RANGES
INSTRUCTIONS POUR L’INSTALLATION DES CUISINIÈRES À GAZ À DOUBLE FOUR DE 30" (76,2 CM)
Table of Contents/Table des matières
RANGE SAFETY.............................................................................. |
2 |
INSTALLATION REQUIREMENTS................................................. |
4 |
Tools and Parts............................................................................. |
4 |
Location Requirements................................................................. |
4 |
Electrical Requirements................................................................ |
6 |
Gas Supply Requirements............................................................ |
6 |
INSTALLATION INSTRUCTIONS................................................... |
7 |
Unpack Range.............................................................................. |
7 |
Adjust Leveling Legs..................................................................... |
7 |
Install Anti-Tip Bracket................................................................. |
8 |
Make Gas Connection.................................................................. |
8 |
Verify Anti-Tip Bracket Is Installed and Engaged......................... |
9 |
Level Range................................................................................ |
10 |
Electronic Ignition System.......................................................... |
10 |
Complete Installation.................................................................. |
11 |
GAS CONVERSIONS.................................................................... |
12 |
LP Gas Conversion..................................................................... |
12 |
Natural Gas Conversion............................................................. |
15 |
SÉCURITÉ DE LA CUISINIÈRE.................................................... |
19 |
EXIGENCES D’INSTALLATION.................................................... |
20 |
Outils et pièces........................................................................... |
20 |
Exigences d’emplacement......................................................... |
21 |
Spécifications électriques........................................................... |
22 |
Spécifications de l’alimentation en gaz...................................... |
23 |
INSTRUCTIONS D’INSTALLATION............................................. |
24 |
Déballage de la cuisinière........................................................... |
24 |
Réglage des pieds de nivellement............................................. |
24 |
Installation de la bride antibasculement..................................... |
25 |
Raccordement au gaz................................................................ |
25 |
Vérifier que la bride antibasculement |
|
est bien installée et engagée...................................................... |
26 |
Réglage de l’aplomb de la cuisinière......................................... |
27 |
Système d’allumage électronique.............................................. |
27 |
Achever l’installation................................................................... |
28 |
CONVERSIONS POUR CHANGEMENT DE GAZ....................... |
29 |
Conversion pour l’alimentation au propane............................... |
29 |
Conversion pour l’alimentation au gaz naturel........................... |
33 |
IMPORTANT:
Save for local electrical inspector’s use.
Installer: Leave installation instructions with the homeowner. Homeowner: Keep installation instructions for future reference.
IMPORTANT :
À conserver pour consultation par l’inspecteur local des installations électriques. Installateur : Remettre les instructions d’installation au propriétaire. Propriétaire : Conserver les instructions d’installation pour référence ultérieure.
W10722849C
RANGE SAFETY
Your safety and the safety of others are very important.
many important safety messages in this manual and on your appliance. Always read and obey all safety
safety alert symbol.
alerts you to potential hazards that can kill or hurt you and others.
messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” mean:
DANGER 
WARNING
You can be killed or seriously injured if you don't immediately follow instructions.
You can be killed or seriously injured if you don't follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.
–Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
–WHAT TO DO IF YOU SMELL GAS:
•Do not try to light any appliance.
•Do not touch any electrical switch.
•Do not use any phone in your building.
•Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
•If you cannot reach your gas supplier, call the fire department.
–Installation and service must be performed by a qualified installer, service agency or the gas supplier.
WARNING: Gas leaks cannot always be detected by smell.
Gas suppliers recommend that you use a gas detector approved by UL or CSA.
For more information, contact your gas supplier.
If a gas leak is detected, follow the “What to do if you smell gas” instructions.
IMPORTANT: Do not install a ventilation system that blows air downward toward this gas cooking appliance. This type of ventilation system may cause ignition and combustion problems with this gas cooking appliance resulting in personal injury or unintended operation.
2
In the State of Massachusetts, the following installation instructions apply:
■Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by the State of Massachusetts.
■If using a ball valve, it shall be a T-handle type.
■A flexible gas connector, when used, must not exceed 3 feet.
WARNING
Tip Over Hazard A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation instructions.
Slide range back so rear range foot is engaged in the slot of the anti-tip bracket. Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed and engaged.
Failure to follow these instructions can result in death or serious burns to children and adults.
Anti-Tip
Bracket
Range Foot
To verify the anti-tip bracket is installed and engaged:
•Slide range forward.
•Look for the anti-tip bracket securely attached to floor or wall.
•Slide range back so rear range foot is under anti-tip bracket.
•See installation instructions for details.
3
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
Tools needed
■■ |
Tape measure |
■■ |
1/8" (3.2 mm) drill bit |
■■ |
Phillips screwdriver |
■■ |
Marker or pencil |
■■ |
TORX®† T20®† screwdriver |
■■ |
Pipe-joint compound |
■■ Flat-blade screwdriver |
|
resistant to LP gas |
|
|
Noncorrosive leak- |
||
■■ |
1/8" flat-blade screwdriver |
■■ |
|
|
detection solution |
||
|
Level |
|
|
■■ |
For LP/Natural Gas |
||
■■ |
Hand or electric drill |
Conversions |
|
■■ |
Wrench or pliers |
■■ |
½" combination wrench |
■■ |
Pipe wrench |
■■ |
9/32" (7.0 mm) nut driver |
■■ |
15/16" combination wrench |
■■ |
Masking tape |
Parts supplied
Check that all parts are included.
■■ LP/Natural Gas Conversion Kit (located on back of range near lower side)
■■ Burner grates ■■ Burner caps ■■ Oven racks
■■ 2 - #12 x 15/8" screws (for mounting anti-tip bracket)
■■ Anti-tip bracket (taped inside upper oven with package containing literature)
Anti-tip bracket must be securely mounted to back wall or floor. Thickness of floor may require longer screws to anchor bracket to subfloor. Longer screws are available from your local hardware store.
Parts needed
Check local codes and consult gas supplier. Check existing gas supply and electrical supply. See the “Electrical Requirements” and “Gas Supply Requirements” sections.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.
■■ It is the installer’s responsibility to comply with installation clearances specified on the rating number plate. The rating number plate is located behind the control panel.
■■ The range should be located for convenient use in the kitchen.
■■ Recessed installations must provide complete enclosure of the sides and rear of the range.
■■ To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood or microwave hood combination that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.
■■ All openings in the wall or floor where range is to be installed must be sealed.
■■ Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.
■■ The floor anti-tip bracket must be installed. To install the antitip bracket shipped with the range, see the “Install Anti-Tip Bracket” section.
■■ Grounded electrical supply is required. See the “Electrical Requirements” section.
■■ Proper gas supply connection must be available. See the “Gas Supply Requirements” section.
■■ Contact a qualified floor covering installer to check that the floor covering can withstand at least 200°F (93°C).
■■ Use an insulated pad or ¼" (0.64 cm) plywood under range if installing range over carpeting.
IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate, or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C).
Mobile Home - Additional Installation Requirements
The installation of this range must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A, or with local codes.
In Canada, the installation of this range must conform with the current standards CAN/CSA-A240-latest edition, or with local codes.
Mobile home installations require:
■■ When this range is installed in a mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above.
†®TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.
4
Product Dimensions
A
F
A.353/4" ± 1/8" (90.8 cm ± 0.3 cm) cooktop height (minimum) with leveling legs screwed all the way in
B.Model/serial/rating plate (located behind the control panel)*
C.471/8" ± 1/8" (119.7 cm
± 0.3 cm) overall height (minimum) with leveling legs screwed all the way in**
B*
C**
D
E***
D.281/2" ± 1/4" (72.4 cm ± 0.6 cm) depth with handle
E.261/8" to 271/4" ± 1/8" (66.4 to 69.2 cm ± 0.3 cm)***
F.2915/16" ± 1/16" (76.0 cm
± 0.2 cm) width
*Model/serial/rating plate may be rotated up from behind the control panel for viewing from the front of the range.
**Range can be raised approximately 1" (2.5 cm) by adjusting the leveling legs.
***Excludes handle. Dimension given is from wall to front of oven door and will vary based on electrical outlet receptacle installation.
Cabinet Dimensions
Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop height.
IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface.
Range may be installed with zero clearance to combustible construction at the rear and on the sides below the cooktop.
B |
D |
C
A
E
F |
|
J |
I |
G |
|
|
|
|
|||
|
K |
|
|
|
|
|
|
L |
|
|
|
|
|
|
|
|
|
|
|
|
H |
|
|
|
|
|
8½" |
|
|
|
|
|
(21.6 cm) |
|
|
|
|
|
|
* |
14" |
|
|
|
|
(35.6 cm) |
|
|
|
|
|
** |
|
|
|
|
1½" |
|
2¼" (5.7 cm) |
|
|
|
(3.8 cm) |
|
|
|
|
|
|
1¼"* |
|
|
|
|
|
(3.2 cm) |
|
|
|
|
|
8½" (21.6 cm)** |
|
|
|
|
|
gas line location |
|
A.18" (45.7 cm) upper cabinet to countertop
B.15" (38.1 cm) max. upper cabinet depth
C.30" (76.2 cm) min. opening width
D.For minimum clearance to the top of the cooktop, see NOTE.
E.30" (76.2 cm) min. opening width
F.3" (7.6 cm) min. clearance from both sides of the range to the side wall or other combustible material
G.Cabinet door or hinges should not extend into the cutout.
H.3" (7.6 cm) distance from wall
I.11/2" (3.8 cm) min. from right side cabinet
J.8" (20.3 cm) width
K.7" (17.8 cm) height
L.2" (5.1 cm) min. from floor
*Drill on centerline 1¼" (3.2 cm) from rear wall for gas supply line.
**Gas lines must be installed within the shaded area to ensure proper alignment of this oven with cabinets.
***Electrical plugs must be installed within the shaded area to ensure proper alignment of this oven with cabinets.
NOTE: 24" (61.0 cm) minimum when bottom of wood or metal cabinet is covered by not less than 1/4" (0.64 cm) flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum, or 0.020" (0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking platform and the bottom of an uncovered wood or metal cabinet.
5
Electrical Requirements
WARNING
Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.
IMPORTANT: The range must be electrically grounded in accordance with local codes and ordinances, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.
If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path is adequate.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
■■ A 120-volt, 60 Hz., AC-only, 15-amp fused, electrical circuit is required. A time-delay fuse or circuit breaker is also recommended. It is recommended that a separate circuit serving only this range be provided.
■■ Electronic ignition systems operate within wide voltage limits, but proper grounding and polarity are necessary. Check that the outlet provides 120-volt power and is correctly grounded.
■■ The wiring diagram is located on the back of the range in a clear plastic bag.
†®TEFLON is a registered trademark of Chemours.
Gas Supply Requirements
WARNING
Explosion Hazard
Use a new CSA International approved gas supply line. Install a shut-off valve.
Securely tighten all gas connections.
If connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and authorized service personnel.
Failure to do so can result in death, explosion, or fire.
Observe all governing codes and ordinances.
IMPORTANT: This installation must conform with all local codes and ordinances. In the absence of local codes, installation must conform with American National Standard, National Fuel Gas Code ANSI Z223.1 – latest edition or CAN/CGA B149 – latest edition.
IMPORTANT: Leak testing of the range must be conducted according to the manufacturers instructions.
Type of Gas
Natural gas:
■■ This range is factory set for use with Natural gas. See the “Gas Conversions” section. The model/serial/rating plate located behind the control panel has information on the types of gas that can be used. If the types of gas listed do not include the type of gas available, check with the local gas supplier.
LP gas conversion:
Conversion must be done by a qualified service technician.
No attempt shall be made to convert the appliance from the gas specified on the model/serial/rating plate for use with a different gas without consulting the serving gas supplier. See the “Gas Conversions” section.
Gas Supply Line
■■ Provide a gas supply line of ¾" (1.9 cm) rigid pipe to the range location. A smaller size pipe on longer runs may result in insufficient gas supply. With LP gas, piping or tubing size can be ½" (1.3 cm) minimum. Usually, LP gas suppliers determine the size and materials used in the system.
NOTE: Pipe-joint compounds that resist the action of LP gas must be used. Do not use TEFLON®† tape.
6
Loading...