INSTRUCTION MANUAL
VHF P25 TRUNKING
HANDHELD TRANSCEIVERS
iF9011 series
UHF P25 TRUNKING
HANDHELD TRANSCEIVERS
iF9021 series
iF9023 series
The photo shows the 10-key
type VHF transceiver.
IMPORTANT
10-key typeSimple typeNon-display type
EXPLICIT DEFINITIONS
READ ALL INSTRUCTIONS carefully and com-
pletely before using the transceiver.
SAVE THIS INSTRUCTION MANUAL — This
instruction manual contains important oper ating instructions
for the IC-F9011B/IC-F9011S/IC-F9011T VHF P25 TRUNK-
ING HANDHELD TRANSCEIVERS and the IC-F9021B/IC-
F9021S/IC-F9021T, IC-F9023B/IC-F9023S/IC-F9023T UHF
P25 TRUNKING HANDHELD TRANSCEIVERS.
When the optional UT-125
✔
unit is installed:
When you attempt to re-export this product and/or AES encryption of this product is activated, you must comply with
the export regulations of your country, which can be highly
restrictive. YOUR FAILURE TO COMPLY WITH EXPORT
REGULATIONS MAY SUBJECT YOU TO FINES OR PENALTIES. AES encryption products including this software
fall under the control of the Japanese Government as described in Appendix I: Export Legal Controls and Appendix:
Exchange Legal Controls. Please consult with your dealer or
sales representative for details.
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany,
France, Spain, Russia, Australia, New Zealand, and /or other countries.
All other products or brands are registered trademarks or trademarks of their
respective holders.
i
aes /de s e ncryption
WORD DEFINITION
RDANGER!
RWARNING!
CAUTION
NOTE
See the operating guide for details of Analog, MDC and
P25 Trunking/Conventional system operations. Consult
your Icom dealer or system operator for details concerning your transceivers programming.
INFORMATION:
✔
In this instruction manual, the following descriptions are used;
IC-F9011B/IC-F9021B/IC-F9023B : “Non-display type”
IC-F9011S/IC-F9021S/IC-F9023S : “Simple type”
IC-F9011T/IC-F9021T/IC-F9023T : “10-key type”
Personal death, serious injury or an explosion may occur.
Personal injury, fire hazard or electric
shock may occur.
Equipment damage may occur.
If disregarded, inconvenience only. No risk
of personal injury, fire or electric shock.
FCC INFORMATION
• FOR CLASS B UNINTENTIONAL RADIATORS:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications to this transceiver, not
expressly approved by Icom Inc., could void your authority to
operate this transceiver under FCC regulations.
ABOUT IPR
This device is made under license under one or more of the
following U.S. Patents: #4,590,473; #4,636,791; #5,148,482;
#5,185,796; #5,271,017; #5,377,229; #4,716,407;
#4,972,460; #5,502,767; #5,146,497; #5,164,986;
#5,185,795; #5,164,986, #5,185,795, and #5,146,497.
* IPR means ‘Intellectual Property Rights.’
VOICE CODING TECHNOLOGY
The AMBE+2™ voice coding Technology embodied in this
product is protected by intellectual property rights including
patent rights, copyrights and trade secrets of Digital Voice
Systems, Inc. This voice coding Technology is licensed solely
for use within this Communications Equipment. The user of
this Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or disassemble
the Object Code, or in any other way convert the Object Code
into a human-readable form. U.S. Patent Nos.
#5,870,405, #5,826,222, #5,754,974, #5,701,390, #5,715,365,
#5,649,050, #5,630,011, #5,581,656, #5,517,511, #5,491,772,
#5,247,579, #5,226,084 and #5,195,166.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
ii
PRECAUTIONS
R DANGER! Use and charge only specified Icom battery
packs with Icom radios or Icom chargers. Only Icom battery
packs are tested and approved for use with Icom radios or
charged with Icom chargers. Using third-party or counterfeit
battery packs or chargers may cause smoke, fire, or cause
the battery to burst.
R WARNING! NEVER hold the radio so that the antenna
is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The radio will perform best if the microphone is 5 to 10 cm (2 to 4 inches) away
from the lips and the radio is vertical.
R WARNING! NEVER operate the radio with a headset
or other audio accessories at high volume levels. The continuous high volume operation may cause a ringing in your
ears. If you experience the ringing, reduce the volume level
or discontinue use.
R WARNING! NEVER operate the radio while driving a
vehicle. Safe driving requires your full attention—anything
less may result in an accident.
CAUTION: MAKE SURE the flexible antenna and battery
pack are securely attached to the radio, and that the antenna
and battery pack are dry before attachment. Exposing the inside
of the radio to water will result in serious damage to the radio.
DO NOT push [PTT] when you do not actually intend to
transmit.
iii
DO NOT operate or place the radio in direct sunlight or in
areas with temperatures below –20°C (–4°F) or above +60°C
(+140°F).
DO NOT modify the radio. The specifications may change
and then not comply with the requirements of a corresponded
regulation. The radio warranty does not cover any problems
caused by unauthorized modification.
DO NOT operate the radio near unshielded electrical blast-
ing caps.
DO NOT use harsh solvents such as benzine or alcohol
when cleaning, as they will damage the radio surfaces.
BE CAREFUL! The transceiver meets IP57 requirements for
dust-protection and waterproof protection. However, once the
transceiver has been dropped, dust-protection and waterproof
protection cannot be guaranteed due to the fact that the trans
ceiver may be cracked, or the waterproof seal damaged, etc.
-
BE CAREFUL! The radio will become hot when operating it
continuously for long periods of time.
MAKE SURE to turn OFF the radio power before connect-
ing or disconnecting the supplied/optional accessory.
Even when the radio power is OFF, a slight current still flows
in the circuits. Remove the battery pack or batteries from
the radio when not using it for a long time. Otherwise, the installed battery pack or batteries will become exhausted, and
will need to be recharged or replaced.
TABLE OF CONTENTS
IMPORTANT .......................................................................... i
EXPLICIT DEFINITIONS ....................................................... i
FCC INFORMATION ............................................................ ii
ABOUT IPR .......................................................................... ii
VOICE CODING TECHNOLOGY ......................................... ii
PRECAUTIONS ................................................................... iii
TABLE OF CONTENTS ....................................................... iv
1 ACCESSORIES ...........................................................1−2
■ Supplied accessories ...................................................1
■ Accessory attachments ................................................ 1
2 PANEL DESCRIPTION ..............................................3−11
■ Front panel ...................................................................3
■ Function display (Simple/10-key types only) ................5
■ Programmable function keys ........................................ 6
3 BASIC OPERATION ................................................ 12−16
■ Turning power ON ......................................................12
■ Channel selection ....................................................... 12
■ Receiving and transmitting .........................................13
■ User set mode ............................................................ 14
■ Clock function .............................................................15
■ LED indicator (Non-display type only) ......................... 16
4 BATTERY CHARGING ............................................17−20
■ Caution ....................................................................... 17
■ Optional battery chargers ........................................... 19
5 BATTERY CASE ............................................................ 21
■ Optional battery case (BP-237) .................................. 21
6 SPEAKER MICROPHONE ............................................22
■ Optional speaker microphone (HM-184/HM-184H) ....22
7 OPTIONS .................................................................23−25
8 SAFETY TRAINING INFORMATION ............................. 26
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
iv
1
y release
Batter
ACCESSORIES
■ Supplied accessories
The following accessories are supplied.
Battery pack
Flexible
antenna
Belt clip
Connector cover
(with screw)
D Battery pack
To attach the battery pack:
Slide the battery pack on the back of the transceiver in the direction of the arrow (q), then lock it with the battery release button.
• Slide the battery pack until the battery release button makes a
‘click’ sound.
To release the battery pack:
Slide the battery release button in the direction of the arrow
(w) as shown below. The battery pack is then released.
NEVER release or attach the battery pack when the transceiver is wet or soiled. This may result water or dust getting into the transceiver/battery pack and may result in the
transceiver being damaged.
■ Accessory attachments
D Flexible antenna
Connect the supplied flexible antenna to the antenna connector.
CAUTION:
• NEVER carry the transceiver by
holding the antenna.
• DO NOT connect the antenna other
than listed on p. 23.
• Transmitting without an antenna may
damage the transceiver.
1
NOTE:
casionally clean them.
y pack
w
Keep battery terminals clean. It’s a good idea to oc-
q
Batter
button
ACCESSORIES
w
Connector
1
D Belt clip
To attach the belt clip:
q Release the battery pack if it is attached.
w Slide the belt clip in the direction of the arrow until the belt
clip is locked and makes a ‘click’ sound.
To detach the belt clip:
q Release the battery pack if it is attached.
w Pinch the clip (q), and slide the belt clip in the direction of
the arrow (w).
q
D Connector cover
Attach the connector cover when the optional equipment is
not used.
To attach the connector cover:
q Insert the connector cover
into the multi-connector.
w Tighten the screw.
CAUTION:
Attach the connector cover
when the optional equipment
is not used. Otherwise the
terminals of the multi-connector may be shorted by
metal object, etc., and this
could damage the transceiver.
To detach the connector cover:
q Unscrew the screw using a
phillips screwdriver.
w Detach the connector cover
for the optional equipment
connector.
Multiconnector
w
q
cover
q
w
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
2
!5
!1
!2
!4
!3
function at position C will be activated.
2
PANEL DESCRIPTION
■ Front panel
1
*
2
*
i
u
y
t
Speaker
Microphone
Function display*
(p. 5)
1
o*
1
!0*
*1 Simple/10-key types only
*2 10-key type only
1
q
w
e
r
e LED INDICATOR
➥ Lights green while receiving a signal, or when the
squelch is open.
➥ Lights red while transmitting.
➥ The LED indicator indicates some information. (Non-
display type only) (p. 16)
r DEALER-PROGRAMMABLE ABC SWITCH
Desired function can be programmed to each position
(A, B or C) independently by your dealer. (p. 11)
To activate the pre-programmed function, set the white
line of the ABC switch to the position A, B or C.
White line
q ANTENNA CONNECTOR
Connects the supplied antenna. (p. 1)
w DEALER-PROGRAMMABLE KEY [EMR]
Desired function can be programmed by your dealer. (p. 6)
• [Emergency] is pre-programmed as default. (See the operating
guide for details.)
3
When the white line of the ABC switch is
set to the position C, the pre-programmed
PANEL DESCRIPTION
See p. 2 for details.
2
t CHANNEL INDICATOR
➥ Lights white according to the “Backlight” setting of the
user set mode.
➥ When you rotate [Rotary selector] to select the channel
or zone, set the desired channel/zone number to this
point.
y DEALER-PROGRAMMABLE TOGGLE SWITCH
Desired function can be programmed by your dealer.
(p. 11)
When the toggle switch is set to the left side (‘
programmed function will be activated.
u VOLUME CONTROL [VOL]
Rotate to turn the power ON/OFF and adjust the audio
level.
i ROTARY SELECTOR
Rotate to select the pre-programmed memory channels or
the operating zone. (Depending on the pre-setting)
• The channel/zone that is positioned to the channel indicator (t)
is selected as the operating channel/zone.
• Depending on the pre-setting, selecting channel 1 using the rotary selector starts a scan. (Rotary Selector Home function)
o DEALER-PROGRAMMABLE KEYS
[I]/[II]/[III]/[Ω]/[≈]/[∫]/[√] (Simple/10-key types only)
Desired function can be programmed independently by
your dealer. (p. 6)
!0 APP KEY [APP] (Simple/10-key types only)
Desired function can be programmed by your dealer. (p. 6)
’), the pre-
!1 10-KEYPAD (10-key type only)
The keypad allows you to enter digits to:
• Select memory channels, tone channels and DTMF codes (while
in the DTMF code channel selection mode.)
• Start up with the password
• Input the Individual ID code for digital operation. (Depending on
the pre-setting)
!2 HOME KEY [HOME] (Simple/10-key types only)
Desired function can be programmed by your dealer. (p. 6)
• [Home] is pre-programmed as default. (See p. 7 for details.)
!3 PTT SWITCH [PTT]
Push and hold to transmit; release to receive.
• Depending on the pre-setting, when an external unit with its own
PTT switch* is connected to the multi-connector, the transceiver’s [PTT] is disabled.
* Such as an optional speaker-microphone or headset.
!4 DEALER-PROGRAMMABLE KEYS
[Side1]/[Side2]/[Side3]
Desired function can be programmed independently by
your dealer. (p. 6)
!5 MULTI-CONNECTOR
Connect optional equipment.
Connector cover
NOTE: Attach the connector cover when
the optional equipment is not used.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
4
!1
q e y ou itrw
!0
StrongWeak
5
PANEL DESCRIPTION
2
■ Function display (Simple/10-key types only)
001
IC-F
MON CLCK ZONE
q SIGNAL STRENGTH INDICATOR
Indicates relative signal strength level.
w LOW POWER INDICATOR
Appears when low output power is selected.
• When high output power is selected, no indicator appears.
e AUDIBLE INDICATOR
Appears when the channel is in the ‘audible’ (unmute) con-
dition.
r COMPANDER INDICATOR
Appears when the compander function* is activated.
* Analog mode operation only.
ch
-01
9011
t SCRAMBLER INDICATOR
Appears when the voice scrambler or encryption function
is activated.
y BELL INDICATOR
Appears/blinks when the matched signal is received, ac-
cording to the pre-programming.
u TELEPHONE INDICATOR
Appears when a phone call* is received.
* P25 operation only.
i SHORT MESSAGE INDICATOR
Appears when an Status message or Short message is re-
ceived.
o BATTERY INDICATOR
Appears or blinks when the battery power decreases to a
specified level.
Indication
Battery level Full Middle
blinks when the battery is exhausted.
Charging
required
No battery
PANEL DESCRIPTION
2
!0 ALPHANUMERIC DISPLAY
Displays an operating channel number, channel name, Set
mode contents, DTMF code, etc.
!1 KEY INDICATOR
Indicate the programmed function of the front panel keys
([I], [II] and [III]).
See the operating guide for details of Analog, MDC and
P25 Trunking/Conventional system operations. Consult
your Icom dealer or system operator for details concerning your transceiver’s programming.
■ Programmable function keys
The following functions can be assigned to the following programmable function keys and switches;
[EMR], [Side1], [Side2], [Side3], [I]*, [II]*, [III]*, [Ω]*, [≈]*, [∫]*,
[√]*, [APP]*, [HOME]*, ABC switch and Toggle switch.
*Simple/10-key types only
Consult your Icom dealer or system operator for details concerning your transceiver’s programming.
If the key indicator shows the programmed function key
name, push the front panel key ([I], [II] or [III]) under the key
indicator to activate the programmed function.
( The function key name in parentheses in the following expla-
nation is displayed for that key indicator; e.g. “UP”)
For Non-display type:
The programmable key functions are limited and some key
functions should be operated differently from Simple and
10-key types. (See pp. 8 and 9 for details.)
For ABC and Toggle switches:
The programmable key functions to ABC and Toggle switches
are limited. (See p. 11 for details.)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
6
PANEL DESCRIPTION
2
D For All types
PRIO A AND PRIO B KEYS “PRA” “PRB”
Push to select Priority A or Priority B channel.
MR-CH 1, MR-CH 2, MR-CH 3 AND MR-CH 4 KEYS
“CH1” “CH2” “CH3” “CH4”
Push to select the memory channels 1, 2, 3 and 4 directly.
MONI KEY “MON”
➥ Push to mute and release the CTCSS (DTCS), 2-tone,
NAC or Talkgroup ID squelch mute. Open any squelch/deactivate any mute while pushing and holding this key.
• Depending on the pre-setting, the ‘Audible’ (unmute) condition
may automatically return to the ‘Inaudible’ (mute) condition, after
a specified time period.
➥ Depending on the pre-setting, pushing and holding this
key for 1 sec. cancels the scan.
LOCK KEY “LOCK”
➥ Push and hold for 1 sec. to electronically lock all program-
mable keys except the following:
[PTT], [Moni], [Light], [Lock], [Emergency], [Surveillance] and
[OPT 1/2/3].
➥ Push and hold for 1 sec. again to turn the function OFF.
LIGHT KEY “LIGT”
Push to turn the transceiver’s backlight ON for about 5 sec.
when the backlight function is turned OFF in user set mode.
(p. 14)
(Common operation)
HOME KEY “HOME”
Push to return to the stand-by mode.
• After editing some information that requires to be memorized, push
this key to save the editing contents in the memory before returning
to the stand-by mode.
OPT MOMENTARY KEYS “O1M” “O2M” “O3M”
Push to control the output signal level from the optional unit
connector.
7
PANEL DESCRIPTION
2
D For All types (Different operation with Non-display type)
When the following key functions are programmed to Nondisplay type, the key functions may be limited and some key
functions should be operated differently from Simple and
10-key types.
HIGH/LOW KEY “H/L”
Push to select the transmit output power temporarily or permanently, depending on the pre-setting.
• Ask your dealer for the output power level for each selection.
• Emits one beep when Low 1 is selected, two beeps when Low 2 is
selected and three beeps when High is selected. (Non-display type
only)
SCAN KEY “SCAN”
For Simple/10-key types
❍
Push to start and cancel scanning operation.
➥
• When the Power ON Scan, Auto Scan, or Rotary Selector
Home function starts a scan, push this key to cancel the scan.
The canceled scan resumes after the specified time period has
passed.
Push and hold this key for 1 sec. to indicate the scan list,
➥
then push [CH Up] or [CH Down] to select a desired list.
(Depending on the presetting.)
For Non-display type
❍
Push to start and cancel scanning operation.
• When the Power ON Scan, Auto Scan, or Rotary Selector Home
function starts a scan, push this key to cancel the scan. The canceled scan resumes after the specified time period has passed.
• The LED indicator blinks green slowly while scanning.
SURVEILLANCE KEY “SURV”
When this function is turned ON, the beep is not emitted and
the LCD backlight does not light when a signal is received or
a key is pushed.
For Simple/10-key types
❍
Push to turn the surveillance function ON or OFF.
For Non-display type
❍
➥ Push and hold for 1 sec. to turn the surveillance function
ON.
➥ When the surveillance function is ON, push to turn the
function OFF.
TALK AROUND KEY “TA” (Conventional operation only)
The talk around function equalizes the transmit frequency to
the receive frequency for transceiver-to-transceiver communication.
For Simple/10-key types
❍
Push to turn the talk around function ON or OFF.
For Non-display type
❍
➥ Push and hold for 1 sec. to turn the talk around function
ON.
➥ When the talk around function is ON, push to turn the
function OFF.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
8
PANEL DESCRIPTION
2
PRIO A REWRITE AND PRIO B REWRITE KEYS
“PRAR” “PRBR”
For Simple/10-key types
❍
➥ Push to select Priority A or Priority B channel.
➥ Push and hold [Prio A (Rewrite)] or [Prio B (Rewrite)] for
1 sec. to rewrite the operating channel as the Priority A or
Priority B channel.
For Non-display type
❍
Push to select Priority A or Priority B channel.
COMPANDER KEY “COMP”
The compander function reduces noise components from
the transmitted audio to provide clear communication.
For Simple/10-key types
❍
Push to toggle the compander function ON and OFF.
For Non-display type
❍
➥ Push and hold for 1 sec. to turn the compander function ON.
➥ When the compander function is ON, push to turn the
function OFF.
OPT OUT KEYS “OP1” “OP2” “OP3”
For Simple/10-key types
❍
Push to control the output signal level from the optional unit
connector.
For Non-display type
❍
➥ Push and hold for 1 sec. to control the output signal level
from the optional unit connector.
➥ When this key function is activated, push to deactivate
9
the function.
D For Simple/10-key types only
Following key functions cannot be programmed to Non-display types.
CH UP AND DOWN KEYS “UP” “DOWN”
➥ Push to select an operating channel. When [Rotary selec-
tor] selection mode is “operating channel,” this function is
not available.
➥ Push to select a scan group after pushing and holding
[Scan].
ZONE KEY “ZONE”
Push this key, then push [CH Up] or [CH Down] to select the
desired zone.
When [Rotary selector] selects “operating zone,” push this
key to switch the range of selectable zones.
What is “zone”?— Selected channels are assigned to a zone
according to how they are to be used in a group. For example,
‘Staff A’ and ‘Staff B’ are assigned into a “Business” zone, and
‘John’ and ‘Cindy’ are assigned into a “Private” zone.
USER SET MODE KEY “SET”
➥ Push and hold for 1 sec. to enter user set mode.
• During in the user set mode, push this key to select an item that
is enabled by your dealer, and change the value or condition by
pushing [CH Up] or [CH Down].
➥ Push and hold this key for 1 sec. again to exit user set mode.
PANEL DESCRIPTION
During menu mode
or [Menu➤]
2
CLOCK KEY “CLCK”
Push to indicate the current time on the LCD. (p. 15)
• While the current time is indicated, push and hold this key for
1 sec. to enter the time data edit mode.
SCAN ADD/DEL (TAG) KEY “SCAD”
➥ Push to add a channel to, or delete it from the current scan
list.
• When a channel is added to the current scan list, the display
quickly shows “SCAN ON.” When a channel is deleted from the
current scan list, the display quickly shows “SCAN OFF.” After
showing “SCAN ON” or “SCAN OFF,” the display quickly shows
the current scan list text.
➥ You can add a channel to, or delete it from the scan list
after selecting the list.
1.
Hold down for 1 second to display the current scan list, and
then push [CH Up] or [CH Down] to select a desired list.
2. Push this key to add a channel to, or delete it from the
selected list.
•
When a channel is added to the selected scan list, the display
quickly shows “SCAN ON.” When a channel is deleted from
the selected scan list, the display quickly shows “SCAN OFF.”
3. Hold down this key for 1 second to exit the scan list
selection mode.
➥ Push this key while a scan is paused on a channel, except
for primary or secondary channel, and then the channel is
deleted from the scan list.
• Depending on the setting, the deleted channel is added to the
scan list again after the scan is cancelled. (Nuisance Delete
function)
MENU AND MENU ➤ KEYS
( [Menu
[≈], respectively.)
The menu mode is available when either [Menu
[Menu ➤] is assigned to [Ω] or [≈].
During menu mode, the pre-programmed menu items (up to
15) become effective with [I], [II] and [III] keys.
Push [Menu
items, and push [I], [II] or [III] to activate the programmed
function.
] and [Menu ➤] can only be assigned to [Ω] and
] or
]/[Menu ➤] to switch the previous/next 3 menu
Push [Menu➤] or [Menu➤]
001ch-01
IC-F
9011
MON CLCK ZONE
Push [Menu➤]
or [Menu➤]
001ch-01
IC-F
9011
LOCK LIGT SET
Push [Menu➤]
001ch-01
IC-F
9011
SCNA PRA CH1
Menu items
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
10
PANEL DESCRIPTION
2
D For ABC and Toggle switches only
ZONE SWITCH
Selects the pre-programmed zone directly.
PRIO A AND PRIO B SWITCHES
Selects Priority A or Priority B channel.
SURVEILLANCE SWITCH
Turns the surveillance function ON or OFF.
When this function is turned ON, the beep is not emitted and
the LCD backlight does not light when a signal is received or
a key is pushed, etc.
11
MR-CH 1, MR-CH 2, MR-CH 3 AND MR-CH 4 SWITCHES
Selects the memory channels 1, 2, 3 and 4, directly.
TALK AROUND SWITCH (Conventional operation only)
Turns the talk around function ON and OFF.
• The talk around function equalizes the transmit frequency to the
receive frequency for transceiver-to-transceiver communication.
LOCK SWITCH
Turns the lock function ON and OFF.
All programmable keys except the following are locked:
[PTT], [Moni], [Light], [Lock], [Emergency], [Surveillance]
and [OPT 1/2/3].
HIGH/LOW SWITCH
Selects the transmit output power temporarily.
• Ask your dealer for the output power level for each selection.
COMPANDER SWITCH
Turns the compander function ON and OFF.
The compander function reduces noise components from
the transmitted audio to provide clear communication.
OPT MOMENTARY SWITCHES
Controls the output signal level from the optional unit connector.
BASIC OPERATION
3
■ Turning power ON
• Prior to using the transceiver for the first time, the battery
pack must be fully charged for optimum life and operation. (p. 17)
• When you use the transceiver for the first time, or after
the transceiver has sat unused for a long time, make
sure to check the date and time indication after turning
the power ON. If the time and date are not correct, reset
them. (p. 15)
q Rotate [VOL] to turn the power ON.
w If the transceiver is programmed for a start up password,
input the digit codes as directed by your dealer.
• 10-keypad can be used for password input depending on version.
• The keys in the table below can be used for password input.
• The transceiver detects numbers in the same block as identical.
Therefore “01234” and “56789” are the same.
KEY
NUMBER
e When the “PASSWORD” indication does not clear after in-
putting 6 digits, the input code number may be incorrect.
Turn the power OFF and start over in this case.
When you operate Non-display type, the password setting
is not available.
0
5
1
6
2
7
3
8
4
9
■ Channel selection
Several types of channel selections are available. Methods
may differ according to your system set up.
NOTE: Depending on the pre-setting, “EMPTY” appears
on the LCD when selecting an empty channel (no frequency is programmed). (Simple/10-key types only)
NON-ZONE TYPE:
To select the desired operating channel:
• Push [CH Up] or [CH Down].
• Rotate [ROTARY SELECTOR]*.
- Up to pre-programmed 16 channels can be selected.
• Push one of [MR-CH 1] to [MR-CH 4].
ZONE TYPE:
To select the desired zone:
• Push [Zone], then push [CH Up] or [CH Down].
• Rotate [ROTARY SELECTOR]*.
- Up to pre-programmed 16 zones can be selected.
AUTOMATIC SCAN TYPE:
Channel setting is not necessary for this type. When turning power ON, the transceiver automatically starts scanning.
Scanning stops when receiving a call.
* Depending on the pre-setting.
When [Rotary selector] selects “Operating channel,” [CH Up]/[CH
Down] are not available, and when [Rotary selector] selects “Operating zone,” [Zone]/[Zone Up]/ [Zone Down] are not available.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
12
BASIC OPERATION
3
■ Receiving and transmitting
NOTE: Transmitting without an antenna may damage the
transceiver. See p. 1 for accessory attachments.
Receiving:
q Rotate [VOL] to turn the power ON.
w Push [CH Up] or [CH Down], or rotate [ROTARY SELEC-
TOR]* to select a channel, in sequence.
*Depending on the pre-setting.
e When receiving a call, adjust the audio output level to a
comfortable listening level.
Transmitting:
Wait for the channel to become clear to avoid interference.
q While pushing and holding [PTT], speak into the micro-
phone at a normal voice level.
w Release [PTT] to return to receive.
IMPORTANT: To maximize the audio quality of your signal;
1. Pause briefly after pushing [PTT].
2. Hold the microphone 5 to 10 cm (2 to 4 in.) from your
mouth, then speak into the microphone at a normal
voice level.
D Transmitting notes
• Transmit inhibit function
The transceiver has several inhibit functions which restrict
transmission under the following conditions:
- The channel is in mute condition (‘Inaudible’ condition;
“ ” does not appear.)
- The channel is busy.
- Un-matched (or matched) CTCSS is received.
(Depending on the pre-setting.)
- Un-matched (or matched) NAC is received*.
(Depending on the pre-setting.)
*Digital mode operation only.
- The selected channel is a ‘receive only’ channel.
• Time-out timer
After continuous transmission for the pre-programmed time
period, the time-out timer is activated, causing the transceiver to stop transmitting.
• Penalty timer
Once the time-out timer is activated, transmission is further
inhibited for a period determined by the penalty timer.
13
BASIC OPERATION
3
■ User set mode
You can “customize” the transceiver operation to suit your
preferences and operating style.
Entering the user set mode:
q Hold down [User Set Mode] for 1 second to enter the user
set mode.
w Push [User Set Mode] one or more times to select the ap-
propriate item. Then push [CH Up] or [CH Down] to set the
desired level or condition.
• Available set mode functions are Backlight, LCD contrast,
Beep, Beep Level, Ringer Level, SQL Level, AF Min Level,
Mic Gain, VOX Gain*, VOX Delay*, Horn, Battery Voltage,
Signal Moni, Lone Worker and System info.
* Appears only when the external VOX unit is connected.
e Hold down [User Set Mode] for 1 second again to exit the
set mode.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
14
BASIC OPERATION
Date indication format (Y: Year, M: Month, D: Day)
The time indication format (12-hour/24-hour)
3
■ Clock function
The transceiver indicates the current time and date when
[Clock] is pushed. And you can change the indication format
and time/date settings.
When you operate Non-display type, this function is not
available.
When you use the transceiver for the first time, or after the
transceiver has sat unused for a long time, make sure to
check the date and time indication after turning the power
ON. If the time and date are not correct, reset them. (See
‘Time and date settings’ to the right.)
D Time and date indication
q
Push [Clock] to indicate the current time and date on the LCD.
• When the indication format is set to 12-hour, “AM” or “PM” is
indicated.
• The LCD indication returns to the stand-by mode after 30 sec.
has passed with no operation.
12
HR
YMD
MON CLCK ZONE
12:00
08-04-01
PM
Time
Date
D Time and date settings
q Push [Clock] to indicate the current time and date on the
LCD.
12
HR
12:00
YMD
MON CLCK ZONE
w Push and hold [Clock] for 1 sec. to enter the time and date
setting mode.
• The time indication format, “24HR” or “12HR” blinks.
e Push [Clock] to select the desired item to be changed.
08-04-01
12
HR
YMD
MON CLCK ZONE
08-04-01
12:00
PM
PM
w Push [Clock] again to return to the stand-by mode.
15
BASIC OPERATION
3
r Push [CH Up] or [CH Down] to set the selected item.
12
HR
03:00
YMD
MON CLCK ZONE
t Push [Clock] to set.
• The next item blinks.
12
YMD
MON CLCK ZONE
y Repeat steps e to t to set items.
u After setting, push and hold [Clock] for 1 sec. to program.
• Return to the time and date setting mode.
i Push [Clock] to return to the stand-by mode.
08-04-01
HR
03:00
08-04-01
PM
PM
■ LED indicator (Non-display type only)
The LED indicator indicates some information as follows;
(Ref.; R=Red, G=Green, O=Orange)
• TX: Lights Red while transmitting a signal.
R*
• TX low BATT1: TX is performed at Low BATT1.
R* R*
• TX low BATT2: Low BATT2 was detected during TX mode.
R* R* R*R*
• Fast/Slow scan: Blinks while Fast/Slow scan is activated.
G G
• RX: Turns Green while receiving a signal.
G
• Low BATT1: You should charge the battery. (blinks slowly)
G G
• Low BATT2: You must charge the battery. (blinks fast)
G G G G
• CH err: Non-programmed channel is selected.
R O R O R O R O R O R O R O R O
* Lights (or blinks) orange when the optional battery case is at-
tached.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
16
4
BATTERY CHARGING
17
■ Caution
• Misuse of Li-ion batteries may result in the following hazards: smoke, fire, or the battery pack may rupture. Misuse can also cause damage to the battery pack or degradation of battery performance.
• Prior to using the battery pack for the first time, or after not using it for a long time, you must fully charge the
pack. Otherwise, the transceiver may not turn ON.
D Battery caution
• R DANGER! NEVER short terminals (or charging termi-
nals) of the battery pack. Also, current may flow into nearby
metal objects such as a key, so be careful when placing the
battery packs (or the radio) in handbags, etc. Simply carrying with or placing near metal objects such as a key, etc.
may cause shorting. This may damage not only the battery
pack, but also the radio.
• R DANGER! DO NOT hammer or otherwise impact the
battery pack. Do not use the battery pack if it has been
severely impacted or dropped, or if it has been subjected
to heavy pressure. The damage may not be visible on the
outside of the case. Even if the surface of the battery pack
does not show cracks or any other damage, the cells inside
may rupture or catch fire.
• R DANGER! NEVER use or leave the battery pack in
areas with temperatures above +60˚C (+140˚F). High temperature buildup in the battery pack, such as could occur
near fires or stoves, inside a sun heated car, or in direct
sunlight for long periods of time may cause the battery
pack to rupture or catch fire. Excessive temperatures may
also degrade performance or shorten battery life.
• R DANGER! DO NOT expose the battery pack to rain,
snow, seawater, or any other liquids. Do not charge or use
a wet battery pack. If the battery pack gets wet, be sure to
wipe it dry before using.
• R DANGER! KEEP the battery pack away from fire. Fire or
heat may cause them to rupture or explode. Dispose of an
used battery pack in accordance with local regulations.
•
R DANGER! NEVER solder the battery pack terminals, or
modify the battery pack. This may generate heat in the battery,
and the battery pack may burst, emit smoke or catch fire.
• R DANGER! Use the battery pack only with the radio for
which it is specified. Never use a battery pack with any
other equipment, or for any purpose that is not specified
in this sheet.
•
R DANGER! If fluid from inside the battery pack gets in
your eyes, blindness can result. Rinse your eyes with clean
water, without rubbing them, and see a doctor immediately.
• R WARNING! Immediately stop using the battery pack if
it emits an abnormal odor, heats up, or is discolored or deformed. If any of these conditions occur, contact your Icom
dealer or distributor.
BATTERY CHARGING
4
• R WARNING! Immediately wash, using clean water, any
part of the body that comes into contact with fluid from inside the battery pack.
• R WARNING! NEVER put the battery pack in a microwave
oven, high-pressure container, or in an induction heating
cooker. This could cause a fire, overheating, or cause the
battery pack to rupture.
• CAUTION: Always use the battery pack within the specified
temperature range; –30°C to +60°C
the battery itself (–20˚C to +60˚C; –4˚F to +140˚F).. Using
the battery pack out of its specified temperature range will
reduce the performance and the life.
• CAUTION: Shorter battery life could occur if the battery
pack is left fully charged, completely discharged, or in an
excessive temperature environment (above +45˚C; +113˚F)
for an extended period of time. If the battery pack must be
left unused for a long time, it must be detached from the radio after discharging. You may use the battery pack until
the remaining capacity is about half, then keep it safely in a
cool and dry place at the following temperature range:
–20˚C to +45˚C (–4˚F to +113˚F) (within a month)
–20˚C to +35˚C (–4˚F to +95˚F) (within three months)
–20˚C to +25˚C (–4˚F to +77˚F) (within a year)
• BE SURE to replace the battery pack with a new one ap-
proximately five years after manufacturing, even if it still
holds a charge. The inside battery material will become
weak after a period of time, even with little use. The estimated number of times you can charge the battery is between 300 and 500.
(–22°F to +140°F)
and
Even when the battery appears to be fully charged, the operating time of the transceiver may become short when:
• Approximately five years have passed since the battery
was manufactured.
• The battery has been repeatedly charged.
D Charging caution
• R DANGER! NEVER charge the battery pack in areas
with extremely high temperatures, such as near fires or
stoves, inside a sun-heated vehicle, or in direct sunlight. In
such environments, the safety/protection circuit in the battery pack will activate, causing the battery to stop charging.
• R WARNING! NEVER charge or leave the battery pack in
the battery charger beyond the specified time for charging.
If the battery pack is not completely charged by the specified time, stop charging and remove the battery pack from
the battery charger. Continuing to charge the battery pack
beyond the specified time limit may cause a fire, overheating, or the battery pack may rupture.
• R WARNING! NEVER insert the radio (the battery pack
attached to the radio) into the charger if it is wet or soiled.
This could corrode the battery charger terminals or damage the charger. The charger is not waterproof.
• CAUTION: NEVER charge the battery pack outside of
the specified temperature range: 0˚C to +40˚C (+32˚F to
+104˚F). Icom recommends charging the battery at +20˚C
(+68˚F). The battery pack may heat up or rupture if charged
out of the specified temperature range. Additionally, battery
performance or battery life may be reduced.
•
CAUTION: DO NOT place the charger on unstable surfaces.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
BATTERY CHARGING
AD-110
supplied
charger
Connectors
This illustration shows the BC-119N.
TRANSCEIVER
Tu rn power OFF
Optional OPC-515L* (f
13.8
CP-23L (f
lighter so
instead of the po
White line: Black line :
4
D AD-110 installation
The AD-110 charger adapter must be installed into the BC119N or BC-121N before battery charging.
➥ Connect the AD-110 and the BC-119N/BC-121N as shown
below, then install the AD-110 into the holder space of the
BC-119N or BC-121N with the supplied screws.
Plugs
■ Optional battery chargers
Screws
with the
adapter
D Rapid charging with the BC-119N+AD-110
The optional BC-119N rapidly charges the Li-Ion battery pack.
Charging time: Approximately 4 hours for the BP-254.
The following items are additionally required.
• AD-110
• A power adapter (may be supplied with BC-119N depending on version) or the DC power cable (OPC-515L/CP-23L).
charger adapter (purchase separately)
BATTERY
PACK
Power adapter
(Not supplied with
some versions.)
V power source) or
or 12 V cigarette
cket) can be used
CAUTION: NEVER connect the OPC-
*
515L to a power source using reverse
polarity. This will ruin the battery charger
or
wer adapter.
AD-110 charger
adapter is installed
in BC-119N.
19
BATTERY CHARGING
Po
(Purchased
adapters are installed
4
D Rapid charging with the BC-121N+AD-110
The optional BC-121N can simultaneously charge up to 6 Liion battery packs.
Charging time: Approximately 4 hours for the BP-254.
The following items are additionally required.
• Six AD-110
•
A power adapter (BC-157S) or the DC power cable (OPC-656)
wer adapter
separately)
charger adapters (purchase separately)
Tu rn power OFF
BATTERY
PACK
OPC-656* DC power cable
(Connect with a DC power supply;
13.8 V/at least 7 A)
*Polarity of the OPC-656
Red line : Black line :
TRANSCEIVER
AD-110 charger
in each slot.
MULTI-CHARGER
IMPORTANT: Battery charging caution
Ensure the guide tabs on the battery pack are correctly
aligned with the guide rails inside the charger adapter.
(This illustration shows the BC-119N.)
Tabs
Guide rails
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
20
Fig.1
5
BATTERY CASE
■ Optional battery case (BP-237)
The optional battery case uses 6 × AA (LR6) size alkaline
batteries. The battery case offers low output power.
q Hook your finger under the latch, and open the cover in
the direction of the arrow (q). (Fig.1)
w Then, install 6 × AA (LR6) size alkaline batteries. (Fig.2)
• Install the alkaline batteries only.
• Be sure to observe the correct polarity.
• Do not pin the ribbon under the batteries.
e Close the cover by fitting in the direction of the arrow (w)
first, then check the latch is in place (e). (Fig.1)
• Be sure the gasket is set correctly, and do not protrude from the
battery case. (Fig.3)
CAUTION:
• When installing batteries, make sure they are all the same
brand, type and capacity. Also, do not mix new and old
batteries together.
• Keep battery terminals clean. It’s a good idea to occasion
ally clean them.
• Never incinerate used battery cells since internal battery
gas may cause them to rupture.
• Never expose a detached battery case to water. If the bat
tery case gets wet, be sure to wipe it dry before using it.
BP-237
q
w
Fig.2
-
Fig.3
-
Latch
e
Gasket
21
SPEAKER MICROPHONE
PTT SWITCH
Push and hold to
transmit;
release to receiv
6
■ Optional speaker microphone (HM-184/HM-184H)
D Description
NEVER immerse the connector in water. If the connector gets
wet, be sure to dry it BEFORE attaching it to the transceiver.
NOTE: The microphone is located as shown in the diagram above. To maximize the readability of your transmitted signal (voice), hold the microphone approximately 5 to
10 cm (2 to 4 in.) from your mouth, and speak in a normal
voice level.
e.
Tu rn the transceiver
power OFF when attaching or detaching
the microphone.
Microphone
Speaker
Belt clip
D To attach
Attach the connector of the speaker-microphone into the
multi connector on the transceiver and tighten the screw with
a coin or flat head screwdriver.
Screw
Coin
CAUTION: Attach the
multi connector properly,
but do not overtighten.
A loose connection will
allow water intrusion into
the connector; an overtightened connection will
damage the connector
pins in the transceiver.
IMPORTANT: KEEP the connector cover attached to the
transceiver when the speaker-microphone is not in use.
(p. 2) Water will not get into the transceiver even if the
cover is not attached; however, the terminals (pins) will
become rusty, or the transceiver will function abnormally if
the connector gets wet.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
22
7
OPTIONS
D BATTERY PACKS
Battery pack Voltage Capacity Battery life*
BP-254*
BP-237*
1
*
The BP-254 meets IPX7* requirements for waterproof protection.
When it is connected, the transceiver corresponds to IPX7.
2
*
The BP-237 meets IPX4* requirements for splash resistance.
When it is connected, the transceiver corresponds to IPX4.
3
*
When the power save function is turned ON, and the operating
periods are calculated under the following conditions;
TX : RX : standby = 5 : 5 : 90
4
*
Operating period depends on the alkaline cells used.
1
7.4 V
2
A6 × AA (LR6) alkaline
2900 mAh (min.)
3040 mAh (typ.)
Battery case for
9.5 hrs.
—*
3
4
D CHARGERS
• BC-119N desktop charger + AD-110 charger adapter
+ BC-145S ac adapter
For rapid charging of battery pack. A power adapter is sup-
plied with the charger depending on versions.
Charging time: Approximately 4 hours for the BP-254.
• BC-121N
(6 pcs.) + BC-157S
For rapid charging of up to 6 battery packs (six AD-110s are
required) simultaneously. A power adapter should be purchased separately.
Charging time: Approximately 4 hours for the BP-254.
mul ti-char ger + AD-110 cha rge r ad apte r
ac adapter
D CABLES
• CP-23L cigarette lighter cable
Allows charging of the battery pack through a 12 V cigarette
lighter socket. (For BC-119N)
• OPC-515L/OPC-656
dc power cables
Allows charging of the battery pack using a 13.8 V power
source instead of the power adapter.
OPC-515L : For BC-119N
OPC-656 : For BC-121N
• OPC-1870/OPC-1871
zone copy cables
OPC-1870 : Portable to portable zone copy cable.
OPC-1871 : Portable to mobile zone copy cable.
See the operating guide for details.
D OPTIONAL UNITS
• UT-124R man down unit
Provides a measure of safety when working in a hazardous
environment, etc.
• UT-125
aes/des encryption unit
• UT-128 des encryption unit
D ANTENNAS
• FA-S25V/FA-S65V/FA-S66V/FA-S30U/FA-S58U/FA-S75U
flexible antennas
FA-S25V : 136–148 MHz FA-S30U : 380–430 MHz
FA-S65V : 148–160 MHz FA-S58U : 430–470 MHz
FA-S66V : 160–174 MHz FA-S75U : 470–520 MHz
•
FA-S67VC/FA-S76UC
FA-S67VC : 136–174 MHz FA-S76UC : 380–520 MHz
cut antenna
23
OPTIONS
W
witch
MIC/VOX gain
VO
7
D OTHER OPTIONS
• MB-115 belt clip
Exclusive alligator-type belt clip.
• AD-118
Allows you to connect an accessory which uses a HIROSE
plug. See the instruction sheet of the AD-118 for details of
the recommended accessories.
• HM-184/HM-184H
Rugged type speaker-microphone.
The HM-184/H meet IP67* requirements for waterproof protection.
• VS-1MC vox/ptt case + HS-94/HS-95/HS-97 headset
VS-1MC : VOX/PTT switch box for hands-free operation, etc.
HS-94: Ear-hook type HS-95: Neck-arm type
HS-97: Throat microphone
These items have IPX4* waterproof protection. When in use, the
transceiver’s waterproof rating meets IPX4 when they are connected.
* Once these items have been dropped, the IP rating cannot be
Some options may not be available in some countries. Please ask
your dealer for details.
Approved Icom optional equipment is designed for optimal performance when used with an Icom transceiver.
Icom is not responsible for the destruction or damage to an Icom
transceiver in the event it is used with equipment that is not manufactured or approved by Icom.
acc adapter
CAUTION: The AD-118 does not have any waterproof
protection. When it is connected, NEVER expose the
adapter and the transceiver to rain, snow or any liquids.
speaker-microphones
guaranteed because of possible damage to these cases or the
waterproof seal.
D About VS-1MC vox/ptt case
The VS-1MC is a VOX/PTT unit for Icom handheld transceivers, and allows you hands-free operation.
An optional headset (HS-94, etc.) is required for operation.
• The VOX (Voice Operated Transmission) function starts transmission without pushing PTT switch when you speak into the microphone; then, automatically returns to receive when you stop
speaking.
Features
➥ 14-pin Spring-plug type head SP/MIC plug is equipped
➥ Water resistant construction
➥ Durable construction
➥ Equipped with a PTT switch and revolving clip
adjusting pot
ater protection cover
X/PTT select switch
VS-1MC
PTT s
☞ Continues to the next page
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
24
OPTIONS
VO
(default)
(default)
Appear
VOX gain adjustment VOX delay adjustment
7
D About VS-1MC vox/ptt case (Continued)
VOX gain and delay adjustment
q Attach the connector of the VS-1MC into the multi-connec-
tor on the transceiver and tighten the screw.
• Toggle the VOX/PTT select switch to [VOX].
w Enter user set mode. (p. 14)
e Push [Ω] several times to select the “VOX Gain” or “VOX
Delay” items. Then, push [∫] or [√] to set the desired
level/condition.
r Push and hold [Ω] again to exit the user set mode.
• Until turning power OFF, [Ω], [∫] and [√] is not activated as the
assigned key function.
These adjustments are for Simple/10-key types only.
• VOX Gain
The VOX sensitivity level can be adjusted from OFF or 1 to 6
(more sensitive).
VOX OFF
Push
VOX GAIN 3
[∫] or [√]
MON CLCK ZONE
X function is OFF
MON CLCK ZONE
VOX gain level 3
• VOX Delay
The VOX delay time can be set from 0.5 to 3.0 sec. (0.5 sec.
step) for a convenient interval before returning to receive.
VOX DLY0.5
Push
VOX DLY3.0
[∫] or [√]
MON CLCK ZONE
0.5 sec (min.)
If your voice is detected, “TX” appears on the LCD as
shown below during the VOX gain or VOX delay adjustment. (The transmission is not performed.)
VOX GAIN 3TX
MON CLCK ZONE
NOTE: MIC/VOX gain can be adjusted via the Adjusting
pot using a thin screw driver.
MON CLCK ZONE
3.0 sec (max.)
VOX DLY3.0TX
MON CLCK ZONE
25
SAFETY TRAINING INFORMATION
8
Your Icom radio generates RF electromagnetic energy
during transmit mode. This radio is designed for and
classified as “Occupational Use Only”, meaning it must
be used only during the course of employment by in-
WARNING
ment.
This radio has been tested and complies with the FCC RF exposure
limits for “Occupational Use Only”. In addition, your Icom radio complies with the following Standards and Guidelines with regard to RF
energy and electromagnetic energy levels and evaluation of such
levels for exposure to humans:
• FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating
Compliance with FCC Guidelines for Human Exposure to Radio
Frequency Electromagnetic Fields.
• American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio
Frequency Electromagnetic Fields, 3 kHz to 300 GHz.
• American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous
Electromagnetic Fields– RF and Microwave.
•
The accessories (antennas, batteries, belt clips, speaker-microphone, etc. that are listed on pages 23–24) are authorized for use
with this product. Use of accessories other than those specified
may result in RF exposure levels exceeding the FCC and IC requirements for wireless RF exposure.
CAUTION
dividuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use
by the “General Population” in an uncontrolled environ-
To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits
for occupational use, always adhere to the following guidelines:
• DO NOT operate the radio without a proper antenna attached, as
this may damaged the radio and may also exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio
by Icom Inc. or antenna specifically authorized by Icom Inc. for use
with this radio.
•
DO NOT transmit for more than 50% of total radio use time (“50%
duty cycle”). “50% duty cycle” is also applicable to the VOX and/
or PSTN (Public Switched Telephone Network) mode. Transmitting
more than 50% of the time can cause FCC RF exposure compliance
requirements to be exceeded. The radio is transmitting when the TX
indicator lights red. You can cause the radio to transmit by pressing
the “PTT” switch.
•
ALWAYS keep the antenna at least 2.5 cm (1 in.) away from the body
when transmitting and only use the Icom belt-clips listed on p. 24
when attaching the radio to your belt, etc., to ensure FCC RF exposure compliance requirements are not exceeded.
cipients of your transmission the best sound quality, hold the antenna
at least 5 cm (2 in.) from your mouth, and slightly off to one side.
The information listed above provides the user with the information needed
to make him or her aware of RF exposure, and what to do to assure that
this radio operates with the FCC RF exposure limits of this radio.
Electromagnetic Interference/Compatibility
During transmissions, your Icom radio generates RF energy that could
possible cause interference with other devices or systems. To avoid
such interference, turn off the radio in areas where signs are posted
to do so. DO NOT operate the transmitter in areas that are sensitive to
electromagnetic radiation such as hospitals, aircraft, and blasting sites.
Occupational/Controlled Use
The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons
are fully aware of the potential for exposure and can exercise control
over their exposure.
To provide the re-
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
26
A-6662D-1US-i
Printed in Japan
© 2008−2015 Icom Inc.
Printed on recycled paper with soy ink.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Loading...