Icom IC-F6122DD, IC-F5122DD Instructions Manual
Status indicator
Cloning jack
ABOUT THE STATUS INDICATOR
Status indicator
RS-232C
Straight cable
RS-232C Cross cable
RS-232C
Straight cable
RF Link
mation
Collecting position,
ABOUT ETHERNET PORT INDICATORS
VHF DIGITAL TRANSCEIVER
Iç-F5122DD
UHF DIGITAL TRANSCEIVER
Iç-F6122DD
Normally packet data from data software or hardware sensor
are exchanged between 2 computers or equivalent devices
using RS-232C serial cable or ETHERNET cable.
A pair of IC-F5122DD/IC-F6122DD is replacing part of communication cable with a wireless connection.
Example of use:
environment,
instrument,
or control information
INSTRUCTIONS
ABOUT IC-F5122DD/IC-F6122DD
Sending position,
environment,
instrument,
or control infor
Thank you for choosing the IC-F5122DD vhf digi-
tal transceiver or IC-F6122DD uhf digital trans-
ceiver.
Read this instructions for periodic transceiver checks
and simple maintenance.
PANEL DESCRIPTION
Ethernet port*
RS-232C connector
* The Ethernet port may not be installed, depending on the transceiv-
er version.
FUSE REPLACEMENT
A fuse is installed in the supplied DC power cable. If a fuse
blows, track down the source of the problem, repair it, and
then replace the damaged fuse with a new rated one.
❏ Fuse rating: 10 A
USE only a 10 A fuse.
CLEANING
If the transceiver becomes dusty or dirty, wipe it clean with a
soft, dry cloth.
DO NOT use harsh solvents such as benzine or alcohol, as they may damage the transceiver surfaces.
The Status Indicator indicates various transceiver status.
Color Status Description
Green Lit Power ON and standing by
Blinking Receiving data
Red Lit Transmitting data
Orange Blinking A problem occurred.
The cause may differ, depending on
the blinking pattern.
See the diagram below for details about the blinking patterns and
causes.
• Reducing the transmission output to protect the final amplifier
O O O O
500 ms*
• PLL unlock
O O O O O O
500 ms*
• Overvoltage
O O O O O O
500 ms*
• Low voltage
O O O O O O O O
500 ms*
*Approximately (ms: millisecond)
O=Orange
If the Status Indicator blinks orange, contact your dealer or
system integrator.
The Ethernet port indicators indicate the status of the network and data.
* The Ethernet port may not be installed, depending on the transceiv-
er version.
SPEED
LINK/ACT
Color Status Description
SPEED Orange
LINK/
ACT
Green
Not lit Connected to 10BASE-T
Lit Connected to 100BASE-TX
Not lit Not connected to the network
Lit Connected to the network
Blinking Receiving and Transmitting data
PIN ASSIGNMENT
• RS-232C connector
15
69
#4-40
inch screw
Pin No. Line Name I/O
1 (No connection) 2 RxD OUT
3 TxD IN
4 DTR IN
5 GND 6 (No connection) 7 RTS IN
8 CTS OUT
9 (No connection) -
• Ethernet port
* The Ethernet port may not be installed, depending on the transceiv-
er version.
1 8
Pin No. Line Name I/O
1 TX+ OUT
2 TX- OUT
3 RX+ IN
4 (No connection) 5 (No connection) 6 RX- IN
7 (No connection) 8 (No connection) -
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany,
France, Spain, Russia, Australia, New Zealand, and/or other countries.
#4-40
inch screw
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
A-7202H-2EX-q Printed in Japan
© 2015 Icom Inc.
Loading...