IBM DJSA-232, DJSA-230, DJSA-220, DJSA-210, DJSA-205 Quick installation guide

IBM storage products

Quick installation guide

Travelstar 32GH, 30GT & 20GN

2.5 inch ATA/IDE hard disk drive

ibm

Models:

Handling precautions

!

!

!

!

!
!

Quick installation*

IMPORTANT: Back up all data before proceeding with
installation.
*It is important to note that the use of Travelstar drives in
some notebooks will require reuse of unique hardware
(for example — mounting trays, connecting cable,
insulating material). If in doubt please consult your
notebook manufacturer as this operation may require a
qualified technician.

Set the jumpers

!

!

!

DJSA-232
DJSA-230

Wear a wrist strap while handling the drive to pre­vent damage from Electrostatic Discharge (ESD).

Set the drive down gently to prevent damage from
impact or vibration.

Do not open the ESD bag containing the drive until
needed.

Handle the drive carefully by the edges. Do not
touch the exposed printed circuit board or any
electronic components.

Do not press on the top or bottom of the drive.
Do not cover the drive’s breather hole.

Master drive. No jumpers are required if the drive is
the only drive in a system or the Master drive in a
two-drive system. See setting A1 opposite.

Slave drive. If the drive is the Slave drive in a two­drive system, jumper setting A2 (see opposite) is
required.

Cable Select. Consult the system manual to see if
your computer supports Cable Select before choos­ing the A3 jumper setting

DJSA-210

.

DJSA-205DJSA-220

Jumper settings

A1. A2. A3. A4. A5.

Pin 1

djsa_qi1.prz

A1. Master
A2. Slave
A3. Cable Select
A4. Never Attach a Jumper Here
A5. Never Attach a Jumper Here

Configure your computer

1. Turn on your computer. Your computer may detect a
configuration change and prompt you to proceed to
the Setup screen.

2. If your computer does not prompt you to reconfigure,
enter your computer’s Setup, typically by key
selection or keyboard combinations during power-on
or during a reboot. Refer to your system manual for
the proper key sequence. If the computer fails to boot
up, power off, remove the drive, and return your
system to its original configuration. Reboot and enter
your computer’s Setup. Follow the directions in
step 3, then attach the drive.

3. Select Auto Detect if your computer Setup supports
this feature. If your computer does not support Auto
Detect, select the appropriate UDT (User Definable
Type) for the drive.

Attach the drive

Consult your system manual for instructions on how to
complete the physical installation of the drive.

IBM Technology Group Support Center version 2.0

Page 1

IBM storage products

Capacity

(GB)

3263862,010DJSA-232
3063658,140DJSA-230
2063438,760DJSA-220
1063219,485DJSA-210

563110,336DJSA-205

Number

HeadsCylindersIBM Model

Sectors

/Track

Partition and format

Using one of the two methods given below, partition and
format your drive:

1. Ontrack Disk Manager 2000

i. For Windows 95 or 98, boot to a DOS prompt with

the system startup diskette and insert the Disk
Manager 200 diskette.
For Windows NT or another operating system boot
with the Disk Manager 200 diskette and select the
appropriate operating system.

ii. Type DM and press Enter to run Disk Manager

200.

iii. Under Select an Installation Option select (E)asy

Disk Installation.

iv.Select the drive to be installed. Disk Manager 200

will partition and format the drive. A status dialog
will indicate a successful installation.

2. FDISK.EXE and FORMAT.EXE

Partitioning with FDISK.EXE

FDISK.EXE or a similar partitioning software from the
operating system may be used in place of Ontrack
Disk Manager 200 to partition your drive. Follow the
instructions provided with your operating system.

NOTE: If the drive capacity displayed by Fdisk does
not match the capacity of your drive, Ontrack Disk
Manager 200 may be required to utilize the full
capacity.

®

© International Business Machines Corporation 2000

www.ibm.com/harddrive
IBM Technology Group Support Center

Telephone: [phone] or 507.286.5825
E-mail: [e-mail]

Singapore Technology Group Support Center

Telephone: [phone]
E-mail: [e-mail]

UK Technology Group Support Center

Telephone: [phone]
E-mail: [e-mail]

Germany Technology Group Support Center

Telephone: [phone]
E-mail: [e-mail]

IBM Systems Technology Division

5600 Cottle Road
San Jose CA 95193
www.ibm.com/storage

Printed in the United States of America
10-2001
All Rights Reserved

Other company, product, and service names may be trademarks or service marks
of others.

Produced by the IBM Technology Group Support Center.
Travelstar 32GH, 30GT & 20GN Hard Disk Drive Specifications, revision 3.0
This product summary is not a substitute for the full production specification,

which should be used when detailed information is required.
Product Description data represents IBM’s design objectives and is provided for

comparative purposes; actual results may vary based on a variety of factors. This
product data does not constitute a warranty. Questions regarding IBM’s warranty
terms or methodology used to derive this data should be referred to the IBM
Technology Group Support Center. Data subject to change without notice.

Date: 12 October 2001

Formatting with FORMAT.EXE

Follow the instructions provided with your operating
system to format the drive. Formatting will verify the
hard disk media and create file allocation tables for
the partition.

Final note

If your system does not boot up after completing the
installation, recheck all settings. If the system still fails
to boot up, remove the Travelstar drive from the system
and contact the IBM Technology Group Support Center.

IBM Technology Group Support Center version 2.0

Page 2