Hyundai ACCENT 2003 Owner Manual
2003
D R I V I N G IS B E L I E V I N G
A010A02A-AAT
WARRANTIES FOR YOUR HYUNDAI VEHICLE
o New Vehicle 60 Months/60,000 Miles Limited Warranty
o New Vehicle 120 Months/100,000 Miles Limited Powertrain Warranty (first owner only)
o Anti-Perforation Limited Warranty
o Emission Defect Warranty - Federal Vehicle
o California Emission Control System Warranty (if applicable)
o Emission Performance Warranty - Federal Vehicle
o Replacement Parts and Accessories Limited Warranty
NOTE:
Detailed warranty information is provided in your Hyundai Owner's Handbook.
A020A01A-AAT
RESPONSIBILITY FOR MAINTENANCE
The maintenance requirements for your new Hyundai are found in Section 5. As the owner, it is your responsibility
to see that all maintenance operations specified by the manufacturer are carried out at the appropriate intervals.
When the vehicle is used in severe driving conditions, more frequent maintenance is required for some operations.
Maintenance requirements for severe operating conditions are also included in Section 5.
OWNER'S MANUAL
A030A03A-AAT
Operation
Maintenance
Specifications
A030A01A
All information in this Owner's Manual is current at the time of publication. However, Hyundai reserves the right to make changes at any
time so that our policy of continual product improvement may be carried out.
This manual applies to all Hyundai models and includes descriptions and explanations of optional as well as standard equipment.
As a result, you may find material in this manual that does not apply to your specific vehicle.
A070A01A-AAT
Your Hyundai should not be modified in any way. Such modifications may adversely affect the performance, safety
or durability of your Hyundai and may, in addition, violate conditions of the limited warranties covering the vehicle.
Certain modifications may also be in violation of regulations established by the U.S. Department of Transportation
and other federal or state agencies.
CAUTION: MODIFICATIONS TO YOUR HYUNDAI
!
A080A01S-AAT
TWO-WAY RADIO OR CELLULAR TELEPHONE INSTALLATION
Your vehicle is equipped with electronic fuel injection and other electronic components. It is possible for an
improperly installed/adjusted two-way radio or cellular telephone to adversely affect electronic systems. For this
reason, we recommend that you carefully follow the radio manufacturer's instructions or consult your Hyundai
dealer for precautionary measures or special instructions if you choose to install one of these devices.
A040A01A-AAT
FOREWORD
Thank you for choosing Hyundai. We are pleased to welcome you to the growing number of discriminating people who
drive Hyundai. The advanced engineering and high-quality construction of each Hyundai we build is something of which
we're very proud.
Your Owner's Manual will introduce you to the features and operation of your new Hyundai. It is suggested that you read
it carefully because the information it contains can contribute greatly to the satisfaction you receive from your new car.
The manufacturer also recommends that all service and maintenance on your car be performed by an authorized Hyundai
dealer. Hyundai dealers are prepared to provide high-quality service, maintenance and any other assistance that may
be required.
A050A04A-AAT
HYUNDAI MOTOR COMPANY
Note:Because future owners will also need the information included in this manual, if you sell this Hyundai, please leave
the manual in the vehicle for their use. Thank you.
!
Severe engine and transaxle damage may result from the use of poor quality fuels and lubricants that do not
meet Hyundai specifications. You must always use high quality fuels and lubricants that meet the specifications listed on Page 9-4 in the Vehicle Specifications section of the Owner's Manual and which also appear
in the Service Station Information on the back cover of the Owner's Manual.
Copyright 2003 Hyundai Motor Company. All rights reserved. No part of this publication may be reproduced, stored in
any retrieval system or transmitted in any form or by any means without the prior written permission of Hyundai Motor
Company.
CAUTION:
A090A01A-AAT
This manual includes information titled as WARNING, CAUTION and NOTE.
These titles indicate the following:
!
!
WARNING:
CAUTION:
This indicates that a condition may result in harm, serious injury or death to you or other persons if
the warning is not heeded. Follow the advice provided with the warning.
This indicates that a condition may result in damage to your vehicle or its equipment if the caution is
not heeded. Follow the advice provided with the caution.
NOTE:
This indicates that interesting or helpful information is being provided.
SAFETY AND VEHICLE DAMAGE WARNING
TABLE OF CONTENTS
SECTION PAGE
1. FEATURES OF YOUR HYUNDAI ....................................................................................... 1-1
2. DRIVING YOUR HYUNDAI ...................................................................................................2-1
3. WHAT TO DO IN AN EMERGENCY .................................................................................. 3-1
4. CORROSION PREVENTION & APPEARANCE CARE ..................................................4-1
5. VEHICLE MAINTENANCE REQUIREMENTS ................................................................. 5-1
6 . DO-IT-YOURSELF MAINTENANCE ...................................................................................6-1
7. EMISSION CONTROL SYSTEMS ..................................................................................... 7-1
8. CONSUMER INFORMATION & REPORTING SAFETY DEFECTS ............................ 8-1
9 . VEHICLE SPECIFICATIONS ............................................................................................... 9-1
10. INDEX ..................................................................................................................................... 10-1
1
2
3
4
5
6
7
8
9
10
YOUR VEHICLE AT A GLANCE
B250A01A-AAT
INSTRUMENTS AND CONTROLS
3
1
45689
2
7
11 12 13 14
10
15 16 17 1819
HLC003
20 21 22
YOUR VEHICLE AT A GLANCE
1. Panel Brightness Control Knob (Rheostat Switch)
2. Rear Wiper/Washer Switch (If Installed)
3. Multi-Function Light Switch
4. Instrument Cluster
5. Horn and Driver's Airbag
6. Windshield Wiper/Washer Switch
7. Digital Clock (If Installed)
8. Rear Window Defroster Switch (If Installed)
9. Hazard Warning Light Switch
10.Front Fog Light Switch (If Installed)
11.Audio System (If Installed)
!
When installing a container of liquid air freshener inside the vehicle, do not place it near the instrument cluster nor
on the instrument panel surface. If there is any leakage from the air freshener onto these areas (Instrument cluster,
instrument panel or air ventilator), it may damage these parts. If the liquid from the air freshener does leak onto these
areas, wash them with water immediately.
CAUTION:
12.Heating/Air Conditioning Control Panel
13.Passenger's Airbag
14.Glove Box
15.Hood Release Lever
16.Multi Box
17.Cigarette Lighter
18.Front Drink Holder
19.Ashtray
20.Shift Lever (If Installed)
21.Parking Brake Lever
22.Rear Drink Holder
YOUR VEHICLE AT A GLANCE
B255A01A-AAT
INDICATOR SYMBOLS ON THE INSTRUMENT PANEL
SRS (Airbag) Service Reminder
Indicator
ABS Service Reminder Indicator (If Installed)
O/D OFF Indicator
(Automatic transaxle only)
Turn Signal Indicator Lights
High Beam Indicator Light
Low Oil Pressure Warning Light
Parking Brake/Low Brake Fluid Level
Warning Light
* A more detailed explanation of these items will be found begining on page 1-34.
Charging System Warning Light
Door Ajar Warning Light
Low Fuel Level Warning Light
Malfunction Indicator Light
Seat Belt Reminder Light
Trunk Lid / Tail Gate Open Warning Light
A100A03A-AAT
Guide to Hyundai Genuine Parts
1. What are Hyundai Genuine Parts?
Hyundai Genuine Parts are the same parts
used by Hyundai Motor Company to manufacture vehicles. They are designed and
tested for the optimum safety, performance,
and reliability to our customers.
2. Why should you use genuine parts?
Hyundai Genuine Parts are engineered and
built to meet rigid original manufacturing
requirements. Using imitation, counterfeit or
used salvage parts is not covered under the
Hyundai New Vehicle Limited Warranty or
any other Hyundai warranty. In addition, any
damage to or failure of Genuine Hyundai
Parts caused by the installation or failure of
an imitation, counterfeit or used salvage part
is not covered by any Hyundai Warranty.
3. How can you tell if you are purchasing
Hyundai Genuine Parts?
Look for the Hyundai Genuine Parts Logo on
the package (see below).
Hyundai Genuine Parts exported to the United
States are packaged with labels written only
in English.
Hyundai Genuine Parts are only sold through
authorized Hyundai Dealerships.
" To find the closest authorized dealer
call 1-800-826-CARS "
A100A03L
A100A01L A100A02L A100A04L
A000A01A-AAT
This Owner's Manual should be considered a part of the car and remain with it when it is sold for the use of the next owner.
OWNER'S I.D.
ORIGINAL OWNER
ADDRESS
CITY STATE ZIP CODE
DELIVERY DATE
(Date Sold to Original Retail purchaser)
DEALER NAME DEALER NO.
ADDRESS
CITY STATE ZIP CODE
1. FEATURES OF YOUR HYUNDAI
Fuel Recommendations..............................................................................1-2
Breaking in Your New Hyundai ............................................................... 1-3
Key........................................................................................................... 1-3, 1-6
Door Locks (Theft-Alarm System)........................................................... 1-4
Window Glass (Power Windows) ................................................... 1-8, 1-9
Seat ................................................................................................................1-10
Seat Belt........................................................................................................1-14
Child Restraint System .............................................................................1-19
Dual-Stage Supplemental Restraint (AIRBAG) System ..................1-26
Instrument Cluster and Indicator Lights................................................1-33
Warning Light and Indicator .....................................................................1-34
Trip Computer ..............................................................................................1-38
Multi-Function Light Switch ......................................................................1-40
Windshield Wiper/Washer Switch ..........................................................1-41
Mirror ..............................................................................................................1-48
Hood Release ..............................................................................................1-51
Heating and Cooling Control....................................................................1-57
Stereo Sound System ...............................................................................1-66
Audio System...............................................................................................1-68
Antenna .........................................................................................................1-83
1
1- 2 FEATURES OF YOUR HYUNDAI
B010A02A-AAT
FUEL RECOMMENDATIONS
Use Unleaded Gasoline
UNLEADED
FUEL ONLY
B010A04A
Unleaded gasoline with a Pump Octane Rating of 87 (Research Octane Number 91) or
higher must be used in your Hyundai.
!
o Do not "TOP-OFF" after the first nozzle
o The fuel cap must be tightened at least 3
B010B01A-AAT
CAUTION:
shut off when refueling.
clicks, otherwise " " light may ill-
uminate.
What About Gasohol?
Gasohol (a mixture of 90% unleaded gasoline
and 10% ethanol or grain alcohol) may be used
in your Hyundai. However, if your engine develops driveability problems, the use of 100% unleaded gasoline is recommended. Fuels with
unspecified quantities of alcohol, or alcohols
other than ethanol, should not be used.
B010D01A-AAT
Do Not Use Methanol
Fuels containing methanol (wood alcohol) should
not be used in your Hyundai. This type of fuel
can reduce vehicle performance and damage
components of the fuel system.
!
Your Hyundai's New Vehicle Limited Warranty may not cover damage to the fuel system
and any performance problems that are caused
by the use of fuels containing methanol or
fuels containing MTBE (Methyl Tertiary Butyl
Ether) over 15.0% vol. (Oxygen Content 2.7%
weight.)
CAUTION:
If leaded gasoline is used, it will cause the
catalytic converter to become ineffective and
the emission control system to malfunction. This
can also result in increased maintenance expense.
To avoid accidental use of leaded fuel, the larger
nozzle used with leaded gasoline at service
stations cannot be inserted into the fuel tank
opening of your Hyundai.
B010C01A-AAT
Use of MTBE
Hyundai recommends that fuels containing
MTBE (Methyl Tertiary Butyl Ether) over 15.0%
vol. (Oxygen Content 2.7% weight) should not
be used in your Hyundai.
Fuel containing MTBE over 15.0% vol. (Oxygen
Content 2.7% weight) may reduce vehicle performance and produce vapor lock or hard starting.
B010E01A-AAT
Gasolines for Cleaner Air
To help contribute to cleaner air, Hyundai recommends that you use gasolines treated with
detergent additives, which help prevent deposit
formation in the engine. These gasolines will
help the engine run cleaner and enhance
performance of the Emission Control System.
B010F01A-AAT
Operation in Foreign Countries
If you are going to drive your Hyundai in another
country, be sure to:
o Observe all regulations regarding registra-
tion and insurance.
o Determine that acceptable fuel is available.
B020A01S-AAT
BREAKING IN YOUR NEW HYUNDAI
During the First 1200 Miles (2000 Km)
No formal "break-in" procedure is required with
your new Hyundai. However, you can contribute
to the economical operation and durability of
your Hyundai by observing the following recommendations during the first 1200 miles (2000
km).
o Don't drive faster than 55 MPH (88 km/h).
o While driving, keep your engine speed (rpm,
or revolutions per minute) between 2,000
rpm and 4,000 rpm.
o Use moderate acceleration. Don't start quickly
or depress the accelerator pedal fully.
o For the first 200 miles (300 km), try to avoid
hard stops.
o Don't lug the engine (in other words, don't
drive so slowly in too high a gear that the
engine "bucks"-shift to a lower gear).
o Whether going fast or slow, vary your speed
from time to time.
o Don't let the engine idle longer than 3 min-
utes at one time.
o Don't tow a trailer during the first 1,200 miles
(2,000 km) of operation.
FEATURES OF YOUR HYUNDAI 1- 3
B030A01A-AAT
KEYS
B030A01E
For greater convenience, the same key operates all the locks in your Hyundai. However,
because the doors can be locked without a key,
carrying a spare key is recommended in case
you accidentally lock one key inside the car.
1- 4 FEATURES OF YOUR HYUNDAI
B030B01A-AAT
Record Your Key Number
B030B01E
A code number is stamped on the number plate
that came with the keys to your Hyundai. This
key number plate should not be left with the
keys but kept in a safe place, not in the vehicle.
The key number should also be recorded in a
place where it can be found in an emergency.
If you need additional keys, or if you should lose
your keys, your authorized Hyundai dealer can
make new keys if you can supply the key
number.
B040A01A-AAT
DOOR LOCKS
!
o Unlocked doors can be dangerous. Be-
o Before opening the door, always look
WARNING:
fore you drive away (especially if there
are children in the car), be sure that all the
doors are securely closed and locked so
that the doors cannot be opened from the
inside. This helps ensure that the doors
will not be opened accidentally. Also,
when combined with the proper use of
seat belts, locking the doors helps keep
occupants from being ejected from the
car in case of an accident.
for and avoid oncoming traffic.
B040B02A-AAT
Locking, unlocking front doors with a
key
UNLOCK
LOCK
HLC2003
o The door can be locked or unlocked with a
key.
o Lock the door by turning the key toward the
front of the vehicle and unlock it by turning
the key toward the rear.
NOTE:
The driver's door can be unlocked by turning
the key once toward the rear. If you wish to
unlock all doors, turn the key toward the rear
within 4 seconds once more. (With central
door locking system)
B040C03A-AAT
Locking from Outside
B040D01FC-GAT
Locking from the Inside
FEATURES OF YOUR HYUNDAI 1- 5
B040E03A-AAT
CHILD-PROTECTOR REAR DOOR
LOCK (If Installed)
HLC2008
The doors can be locked without a key.
To lock the doors, first push the inside lock
switch to the "LOCK" position, so that the red
mark on the switch is not visible, then close the
door.
The door will not lock if the key is left in the
ignition switch when the front doors are closed.
This is normal. (If Installed)
NOTE:
o When locking the door this way, be
careful not to lock the door with the
ignition key left in the vehicle.
o To protect against theft, always re-
move the ignition key, close all windows, and lock all doors and the trunk
lid(4 Door) / tail gate(3 Door) when
leaving your vehicle unattended.
UNLOCK
LOCK
HLC2004
To lock the doors from the inside, simply close
the door and push the lock switch to the "LOCK"
position. When this is done, neither the outside
nor the inside door handle can be used.
NOTE:
When the door is locked, the red mark on the
switch is not visible and the character "LOCK"
on the switch is visible.
HLC2005
Your Hyundai is equipped with a "child-protector" rear door lock assembly. When the lock
mechanism is engaged, the rear door cannot be
opened from the inside. It's use is recommended
whenever there are small children in the rear
seat.
To engage the child-protector feature so that the
door cannot be opened from the inside, move
the child-protector lever to the " " position and
close the door. Move the lever to the opposite
direction of " " position when normal door
operation is desired.
If you wish to be able to open the door from the
outside, the outside door handle will function
normally.
1- 6 FEATURES OF YOUR HYUNDAI
B040G02A-GAT
Central Door Lock (If Installed)
B040G01A
The central door locking is operated by pushing
the driver's door lock switch toward the front or
rear of the vehicle. If the passenger and rear
doors are open when the switch is pushed, the
door will remain locked when closed.
NOTE:
o When pushing the switch toward the rear,
all doors will unlock.
When pushing the switch toward the front,
all doors will lock.
o When the door is unlocked, the red mark
on the switch is visible and the character
"LOCK" on the switch is not visible.
o The central door locking is operated by
turning the key toward the front or rear of
the vehicle.
B070A01A-AAT
THEFT-ALARM SYSTEM
(If Installed)
This system is designed to provide protection
from unauthorized entry into the car. This system is operated in three stages: the first is the
"Armed" stage, the second is the "Alarm" stage,
and the third is the "Disarmed" stage. If triggered, the system provides an audible alarm
with blinking of the turn signal lights.
B070B02A-AAT
Armed Stage
UNLOCK
LOCK
PANIC
B070D02A
Park the car and stop the engine. Arm the
system as described in the following paragraph.
1) Remove the ignition key from the ignition
switch.
2) Make sure that the engine hood and trunk lid
(4 Door)/tail gate (3 Door) are locked.
3) Lock the doors using the transmitter of the
keyless entry system.
After completion of the steps above, the turn
signal lights will blink once to indicate that the
system is armed.
NOTE:
If any door, trunk lid (4 Door)/tail gate (3 Door)
or engine hood remains open, the system will
not be armed. If this happens, rearm the system as described above.
!
o Do not arm the system until all passen-
o If the "LOCK" button is pressed once
CAUTION:
gers have left the car. If the system is
armed while a passenger(s) remains in
the car, the alarm may be activated when
the remaining passenger(s) leaves the car.
more within 4 seconds after pushing the
"LOCK" button on the transmitter, the
alarming horn will sound once to indicate
that the system is armed.
B070C03A-AAT
Alarm Stage
The alarm will be activated if any of the following occurs while the car is parked and the
system is armed.
1) A door or tail gate(3 Door) is opened without
using the transmitter or the ignition key.
2) The trunk lid(4 Door) is opened without using
the ignition key.
3) The engine hood is opened.
The alarming horn will sound and the turn signal
lights will blink continuously for 27 seconds
(This happens 3 times). To turn off the system,
unlock the door with the transmitter or the ignition key.
!
Avoid trying to start the engine while the
system is armed.
CAUTION:
B070D02A-AAT
Disarmed Stage
The system will be disarmed when the following
step is taken:
The driver's or passenger's door is unlocked by
depressing the "UNLOCK" button on the transmitter or the ignition key.
After completion of the steps above, the turn
signal lights will blink twice to indicate that the
system is disarmed.
If any door, trunk lid(4 Door)/tail gate(3 Door) or
engine hood is not opened within 30 seconds,
the system will be rearmed.
NOTE:
When the system is disarmed with the interior
light switched to "DR" or "·", the interior light
will illuminate for 30 seconds.
B070E02A-GAT
Panic Stage
1. Push the "PANIC" button on the transmitter.
2. At the same time, the alarming horn will
sound continuously.
3. To turn off the system, push the "PANIC"
button again on the transmitter.
FEATURES OF YOUR HYUNDAI 1- 7
B070F01O-AAT
Keyless Entry System (If Installed)
Locking doors
1. Close all doors.
2. Push the "LOCK" button on the transmitter.
3. At the same time all doors lock, the turn
signal light will blink once to indicate that the
system is armed.
Unlocking doors
1. Push the "UNLOCK" button on the transmitter.
2. At the same time the driver's door unlocks,
the turn signal light will blink twice to indicate
that the system is disarmed.
NOTE:
If you wish to unlock all the doors, press the
"UNLOCK" button on the transmitter again
within 4 seconds.
1- 8 FEATURES OF YOUR HYUNDAI
B070E02HP-GAT
Replacing the battery
When the transmitter's battery begins to get
weak, it may take several pushes on the button
to lock or unlock the doors, and the LED will not
light. Replace the battery as soon as possible.
Battery type : CR2032
Battery
B070E02A-1
2. Remove the old battery from the case and
note the polarity. Make sure the polarity of
the new battery is the same(+side facing
down), then insert it in the transmitter.
B050A01A-AAT
WINDOW GLASS
B050A01A
To raise or lower the window, turn the window
regulator handle clockwise or counterclockwise.
Screwdriver
B070E03A
Replacement instructions:
1. Separate the case with a blade screwdriver
as shown in the illustration.
!
When opening or closing the windows, make
sure your passenger's arms, hands and body
are safely out of the way.
WARNING:
B060A01E-AAT
POWER WINDOWS (If Installed)
4 Door
3 Door
FEATURES OF YOUR HYUNDAI 1- 9
Auto-Down Window
(Driver's Side) (If Installed)
The Auto-Down window is moved to its fully
open position by pushing the switch. To stop at
the desired position push the switch again.
(1)
(1)
HLC2009
The power windows operate when the ignition
key is in the "ON" position. The main switches
are located on the driver's armrest and control
the front and rear windows on both sides of the
vehicle. The windows may be opened by depressing the appropriate window switch and
closed by pulling up the switch. To open the
window on the driver's side, press the switch(1)
down. The window moves as long as the switch
is operated.
HLC2014
In order to prevent operation of the passenger
front and rear windows, a window lock switch is
provided on the armrest of the driver's door. To
disable the power windows, press the window
lock switch.
To revert to normal operation, press the window
lock switch a second time.
!
1) Be careful that someone's head, hands
2) Never try to operate the main switch on
3) Do not leave children alone in the car.
WARNING:
and body are not trapped by a closing
window.
the driver's door and the individual door
window switch in opposing directions at
the same time. If this is done, the window
will stop and cannot be opened or closed.
Always remove the ignition key for their
safety.
1- 10 FEATURES OF YOUR HYUNDAI
B080A01A-AAT
ADJUSTABLE FRONT SEATS
!
Never attempt to adjust the seat while the
vehicle is moving. This could result in loss of
control, and an accident causing death, serious injury, or property damage.
B080B01A-AAT
Adjusting Seat Forward and Rearward
To move the seat toward the front or rear, pull
the lock release lever upward. This will release
the seat on its track so you can move it forward
or rearward to the desired position.
WARNING:
HLC2026
When you find the position you want, release
the lever and slide the seat forward or rearward
on its track until it locks into the desired position
and cannot be moved further.
B080C01A-AAT
Adjusting Seatback Angle
HLC2027
To recline the seatback, lean forward to take
your weight off it, then pull up on the recliner
control lever at the outside edge of the seat.
Now lean back until the desired seatback angle
is achieved. To lock the seatback into position,
release the recliner control lever.
!
To minimize risk of severe injury in the event
of a collision or sudden stop, both the driver
and passenger seatbacks should always be in
a nearly upright position while the vehicle is
in motion. The protection provided by the
seat belts and airbags in a frontal collision
may be reduced significantly when the
seatback is reclined. There is greater risk
that the driver and passenger will slide
under the seat belt which may result in
serious injury if a crash occurs when the
seatback is reclined.
B080D02A-AAT
WARNING:
Adjustable Headrests
Lock knob
B080D01A
Headrests are designed to help reduce the risk
of neck injuries.
To raise the headrest, pull it up. To lower it,
push it down while pressing the lock knob.
!
o For maximum effectiveness in case of an
o Do not operate the vehicle with the head-
WARNING:
accident, the headrest should be adjusted so the top of the headrest is at the
same height as the top of the occupant's
ears. The use of a cushion that holds the
body away from the seatback is not recommended.
rests removed as severe injury to an occupant may occur in the event of an accident. Headrests may provide protection
against severe neck injuries when properly adjusted.
B080E01O-AAT
Lumbar Support Control
(Driver's seat only) (If Installed)
HLC2029
To adjust the lumbar support, turn the handle
on the outboard or left side of the seat. To
increase the amount of lumbar support, pull
the lever forward. To decrease it, push the
lever toward the rear.
FEATURES OF YOUR HYUNDAI 1- 11
B080F01S-AAT
Seat Cushion Height Adjustment
(Driver's Seat only) (If Installed)
HLC2028
To raise or lower the front part of the seat
cushion, turn the front knob forward or rearward.
To raise or lower the rear part of the seat
cushion, turn the rear knob forward or rearward.
1- 12 FEATURES OF YOUR HYUNDAI
B130A01A-AAT
REAR SEAT ENTRY (For 3-door model)
(1)
B090A01A-GAT
REAR SEAT
Adjustable Headrests
(If Installed)
!
o Do not operate vehicle with the head-
WARNING:
rests removed as severe injury to an
occupant may occur in the event of an
accident. Headrests may provide protection against severe neck injuries
when properly adjusted.
(2)
HTB258
The front passenger's seatback should be tilted
to enter the rear seat.
By pulling up on the recliner control lever (1) at
the outside of the front passenger's seat, the
seatback will tilt forward and the seat will automatically slide forward.
Rear seat occupants can tilt the front passenger's
seatback by depressing the foot lever (2) as
shown in the illustration.
!
Passengers sitting in the rear seat should be
careful not to accidentally press the foot lever
(2) while the vehicle is moving, as this may
cause the seatback to move forward and injure a front seat occupant.
WARNING:
Lock Knob
B090A01A-1
Headrests are designed to help reduce the risk
of neck injuries.
To raise the headrest, pull it up. To lower it, push
it down while pressing the lock knob.
!
o For maximum effectiveness in case of an
WARNING:
accident, the headrest should be adjusted
so the top of the headrest is at the same
height as the top of the occupant's ears.
The use of a cushion that holds the body
away from the seatback is not recommended.
B110A03A-AAT
Folding Rear Seatbacks
(If Installed)
B110A01A-1
For greater convenience, the entire seatback
may be folded down or the seatbacks may be
folded down individually.
o To unlock the seatback, pull up the seatback
locking knob, then push forward on the
seatback panel.
o When you return the seatback to its upright
position, always be sure it has locked into
position by pulling and pushing on the top of
the seatback.
FEATURES OF YOUR HYUNDAI 1- 13
B140A01S-AAT
REAR SEAT WARNING
B110A02A-1
!
The purpose of the fold-down rear seatbacks
is to allow you to carry longer objects than
could otherwise be accommodated. Do not
allow passengers to sit on top of the foldeddown seatback while the car is moving as this
is not a proper seating position and no seat
belts are available for use when the seatbacks
are folded down. This could result in serious
injury or death in case of an accident or a
sudden stop. Objects carried on the foldeddown seatback should not extend higher than
the top of the front seats. This could allow
cargo to slide forward and cause injury or
damage during sudden stops.
WARNING:
!
When you return the rear seatback to its
upright position after being folded down,
be careful not to damage the seat belt
webbing or buckle. In addition, do not allow
the seat belt webbing or buckle to get
caught or pinched in the rear seat.
WARNING:
B140A01A
For the safety of all passengers, luggage or
other cargo should not be piled higher than the
top of the seatback. In addition, do not place
objects on the rear shelf as they may move
forward during braking or in an accident and
strike vehicle passengers.
1- 14 FEATURES OF YOUR HYUNDAI
B150A01A-AAT
SEAT BELT PRECAUTIONS
!
All occupants of the vehicle must wear their
seat belts at all times. Note that this vehicle is
equipped with a Supplemental Restraint
(Airbag) System as discussed beginning on
page 1-26. The seat belts must be used in
conjunction with the supplemental airbag system. State laws require that some or all occupants of the vehicle use seat belts. The possibility of increased injury or severity of injury
in an accident will be increased if this elementary safety precaution is not observed.
WARNING:
B150B02A-AAT
Infant or Small Child
All 50 states have child restraint laws. You
should be aware of the specific requirements in
your state. Child and/or infant safety seats must
be properly placed and installed in the rear seat .
Information about the use of these restraints
begins on page 1-19.
!
Every person in your vehicle needs to be
buckled up at all times, including infants and
children. In a collision, an unrestrained child
can become a "missile" inside the car. The
force required to hold a child on your lap
could be so great that you could not hold the
child. Any child riding in the vehicle should
always be in a proper restraint.
WARNING:
B150C02A-AAT
Larger Children
Children who are too large for child restraint
systems should always occupy the rear seat
and use the available lap/shoulder belts. The
lap portion should be fastened snug on the
hips and as low as possible. Check belt fit
periodically. A child's squirming could put the
belt out of position. Children are afforded the
most safety in the event of an accident when
they are restrained by a proper restraint system in the rear seat. If a larger child (over age
13) must be seated in the front seat, the child
should be securely restrained by the available
lap/shoulder belt and the seat should be placed
in the rearmost position. Children under the
age of 13 should be restrained securely in the
rear seat. NEVER place a child under the age
of 13 in the front seat. NEVER place a rear
facing child seat in the front seat of a vehicle.
NOTE:
Small children are best protected from injury
in an accident when properly restrained in the
rear seat by a child restraint system that
meets the requirements of the Federal Motor
Vehicle Safety Standards. Before buying any
child restraint system, make sure that it has a
label certifying that it meets Motor Vehicle
Safety Standard 213. The restraint must be
appropriate for your child's height and weight.
Check the label on the child restraint for this
information. See page 1-19.
B150D01A-AAT
Pregnant Women
The use of a seat belt is recommended for
pregnant women to lessen the chance of injury
in an accident. When a seat belt is used, the lap
belt portion should be placed as low and snugly
as possible on the hips, not across the abdomen. For specific recommendations, consult a
physician.
B150E01A-AAT
Injured Person
A seat belt should be used when an injured
person is being transported. When this is necessary, you should consult a physician for recommendations.
B150F01A-AAT
One Person Per Belt
Two people (including children) should never
attempt to use a single seat belt. This could
increase the severity of injuries in case of an
accident.
B150G01A-AAT
Do Not Lie Down
To reduce the chance of injuries in the event of
an accident, and to achieve maximum effectiveness of the restraint system, all passengers
should be sitting up and the front seats should
be in an upright position when the car is moving.
A seat belt cannot provide proper protection if
the person is lying down in the rear seat or if the
front seat is in a reclined position.
!
Sitting in a reclined position or lying down
when your vehicle is in motion can be dangerous. Even if you buckle up, your seat belts
can't do their job when you're reclined. The
shoulder belt can't do its job because it won't
be against your body. Instead, it will be in
front of you. In a crash you could go into it
with great force, receiving serious neck or
other injuries. The lap belt can't do its job
either. In a crash the belt could go up over
your abdomen. The belt forces would be there,
not at your strong pelvic bones. This could
cause serious internal injuries.
For proper protection when the vehicle is in
motion, have the seatback upright. Then sit
back in the seat and wear your seat belt
properly. See Page 1-16.
WARNING:
FEATURES OF YOUR HYUNDAI 1- 15
B160A01A-AAT
CARE OF SEAT BELTS
Seat belt systems should never be disassembled or modified. In addition, care should be
taken to assure that seat belts and belt hardware are not damaged by seat hinges, doors or
other abuse.
!
When you return the rear seatback to its
upright position after the rear seatback was
folded down, be careful not to damage the
seat belt webbing or buckle. Be sure that the
webbing or buckle does not get caught or
pinched in the rear seat.
B160B01A-AAT
WARNING:
Periodic Inspection
It is recommended that all seat belts be inspected periodically for wear or damage of any
kind. Parts of the system that are damaged
should be replaced as soon as possible.
1- 16 FEATURES OF YOUR HYUNDAI
B160C01A-AAT
Keep Belts Clean and Dry
Seat belts should be kept clean and dry. If belts
become dirty, they can be cleaned by using a
mild soap solution and warm water. Bleach,
dye, strong detergents or abrasives should not
be used because they may damage and weaken
the fabric.
B160D01A-AAT
When to Replace Seat Belts
Entire in-use seat belt assembly or assemblies
should be replaced if the vehicle has been
involved in an accident. This should be done
even if no damage is visible. Additional questions concerning seat belt operation should be
directed to your Hyundai Dealer.
B170A04A-AAT
HEIGHT ADJUSTABLE FRONT SEAT
SHOULDER BELT
(If Installed)
B170A01A
You can adjust the height of the shoulder belt
anchor to one of the 4 positions for maximum
comfort and safety.
If the height of the adjusting seat belt is too near
your neck, you will not be getting the most
effective protection. The shoulder portion should
be adjusted so that it lies across your chest and
midway over your shoulder nearest the door
and not your neck.
To adjust the height of the seat belt anchor,
lower or raise the height adjuster into an appropriate position. To raise the height adjuster, pull
it up. To lower it, push it down while pressing the
height adjuster button.
Release the button to lock the anchor into
position. Try sliding the height adjuster to
make sure that it has locked into the position.
!
o The height adjuster must be in the
o The misadjustment of height of the shoul-
B180A01A-AAT
WARNING:
locked position when the vehicle is
moving.
der belt could reduce the effectiveness of
the seat belt in a crash.
SEAT BELT-Driver's 3-Point System
with Emergency Locking Retractor
To Fasten Your Belt
B180A01L
FEATURES OF YOUR HYUNDAI 1- 17
To fasten your seat belt, pull it out of the retractor and insert the metal tab into the buckle.
There will be an audible "click" when the tab
locks into the buckle.
The seat belt automatically adjusts to the proper
length only after the lap belt is adjusted manually so that it fits snugly around your hips. If you
lean forward in a slow, easy motion, the belt will
extend and let you move around. If there is a
sudden stop or impact, however, the belt will
lock into position. It will also lock if you try to
lean forward too quickly.
NOTE:
If the driver's seat belt is not fastened when
the ignition key is in the "ON" position, the
seat belt warning light will flash and the warning chime will sound for approximately six
seconds.
B190A01A-AAT
SEAT BELTS-Front Passenger and
Outboard Rear Seat 3-Point System
with Combination Locking Retractor :
To Fasten Your Belt
Combination retractor type seat belts are installed in the rear seat outboard positions to
help accommodate the installation of child restraint systems. Hyundai strongly recommends
that children always be seated in the rear seat .
NEVER place any infant restraint system in
the front seat of the vehicle.
This type of seat belt combines the features
of both an emergency locking retractor seat
belt and an automatic locking retractor seat
belt. To fasten your seat belt, pull it out of the
retractor and insert the metal tab into the
buckle. There will be an audible "click" when
the tab locks into the buckle. When not securing a child restraint, the seat belt operates in
the same way as the driver's seat belt (Emergency Locking Retractor Type). It automatically adjusts to the proper length only after the
lap belt portion of the seat
belt is adjusted manually so that it fits snugly
around your hips. When the seat belt is fully
extended from the retractor to allow the installation of a child restraint system, the seat belt
operation changes to allow the belt to retract,
but not to extend (Automatic Locking Retractor
Type). See page 1-24.
NOTE:
Although the combination retractor provides
the same level of protection for seated passengers in either emergency or automatic
locking modes, it is recommended that seated
passengers use the emergency locking feature for improved convenience. The automatic locking function is intended to facilitate
child restraint installation. To convert from
the automatic locking feature to the emergency locking operation mode, allow the unbuckled seat belt to fully retract.
!
o For maximum restraint system protec-
o Seat belts are most effective when
o Children must always be seatbelted in
o The shoulder belt should be positioned
o Avoid wearing twisted seat belts. A twist-
o Be careful not to damage the belt web-
WARNING:
tion, seat belts must always be used whenever the car is moving.
seatbacks are in the upright position.
the rear seats. Never allow children to
ride in the front passenger seat.
midway over the shoulder nearest the
door for the most effective protection.
Never wear the seat belt under the arm
nearest the door. Wearing the belt under
the arm nearest the door could cause
serious or fatal injuries in an accident.
ed belt can't do its job as well. In a collision, it could even cut into you. Be sure
the belt is straight and not twisted.
bing or hardware. If the belt webbing or
hardware is damaged, replace it.
Loading...