Husqvarna 1330 SB, 96193004200 User Manual

1330SB

Owner's Manual / 96193004200

IMPORTANT

Safe Operation Practices for Walk-Behind Snow Throwers

This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury.

Look for this symbol to point out important safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED.

WARNING: Always disconnect spark plug wire and place it where it cannot contact plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs.

WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should beexercisedwhileusingonslopingsurfaces. Do not use snow thrower on surfaces above ground level such as roofs of residences, garages, porches or other such structures or buildings.

WARNING: Snow throwers have exposed rotating parts, which can cause severe injury from contact, or from material thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

CAUTION: Muffler and other engine parts become extremely hot during operation and remain hot after engine has stopped. To avoid severe burns on contact, stay away from these areas.

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Training

1.Read, understand and follow all instructions on the machine and in the manual(s) before operating this unit. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly.

2.Never allow children to operate the equipment. Never allow adults to operate the equipment without proper instruction.

3.Keep the area of operation clear of all persons, particularly small children.

4.Exercise caution to avoid slipping or falling, especially when operating the snow thrower in reverse.

Preparation

1.Thoroughly inspect the area where the equipment is to be used and remove all doormats, sleds, boards, wires, and other foreign objects.

2.Disengage all clutches and shift into neutral before starting the engine (motor).

3.Do not operate the equipment without wearing adequate winter garments. Avoid loose fitting clothing that can get caught in moving parts. Wear footwear that will improve footing on slippery surfaces.

4.Handle fuel with care; it is highly flammable

(a)Use an approved fuel container.

(b)Never add fuel to a running engine or hot engine.

(c)Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors.

(d)Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the ground, away from your vehicle, before filling.

(e)When practical, remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle.

(f)Keep the nozzle in contact with the rim of the fuel tank or container opening at all times, until refueling is complete. Do not use a nozzle lock-open device.

(g)Replace gasoline cap securely and wipe up spilled fuel.

(h)If fuel is spilled on clothing, change clothing immediately.

5.Use extension cords and receptacles as specified by the manufacturer for all units with electric drive motors or electric starting motors.

6.Adjust the collector housing height to clear gravel or crushed rock surface.

7.Never attempt to make any adjustments while the engine (motor) is running (except when specifically recommended by manufacturer).

8.Always wear safety glasses or eye shields during operation or while performing an adjustment or repair to protect eyes from foreign objects that may be thrown from the machine.

Operation

1.Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.

2.Exercise extreme caution when operating on or crossing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.

3.After striking a foreign object, stop the engine (motor), remove the wire from the spark plug, disconnect the cord on electric motors, thoroughly inspect the snow thrower for any damage, and repair the damage before restarting and operating the snow thrower.

4.If the unit should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning of trouble.

5.Stop the engine (motor) whenever you leave the operating position, before unclogging the collector/impeller housing or discharge chute, and when making any

2	repairs, adjustments or inspections.

6.Whencleaning,repairingorinspectingthesnowthrower, stop the engine and make certain the collector/impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the engine.

7.Do not run the engine indoors, except when starting the engine and for transporting the snow thrower in or out of the building. Open the outside doors; exhaust fumes are dangerous.

8.Exercise extreme caution when operating on slopes.

9.Never operate the snow thrower without proper guards, and other safety protective devices in place and working.

10.Never direct the discharge toward people or areas where property damage can occur. Keep children and others away.

11.Do not overload the machine capacity by attempting to clear snow at too fast a rate.

12.Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when operating in reverse.

13.Disengage power to the collector/impeller when snow thrower is transported or not in use.

14.Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counterweights, or cabs).

15.Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run.

16.Never touch a hot engine or muffler.

Clearing a Clogged Discharge Chute

Hand contact with the rotating impeller inside the discharge chute is the most common cause of injury associated with snow throwers. Never use your hand to clean out the discharge chute. To clear the chute:

1.SHUT THE ENGINE OFF!

2.Wait 10 seconds to be sure the impeller blades have stopped rotating.

3.Always use a clean-out tool, not your hands.

Maintenance and Storage

1.Check shear bolts and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition.

2.Never store the machine with fuel in the fuel tank inside a building where ignition sources are present such as hot water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing in any enclosure.

3.Always refer to operator’s manual for important details if the snow thrower is to be stored for an extended period.

4.Maintain or replace safety and instruction labels, as necessary.

5.Run the machine a few minutes after throwing snow to prevent freeze-up of the collector/impeller.

CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and manufactured to give best possible dependability and performance.

Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center. We have competent, well-trained technicians and the proper tools to service or repair this unit.

Please read and retain this manual. The instructions will enable you to assemble and maintain your snow thrower properly. Always observe the “SAFETY RULES”.

SERIAL NUMBER: ___________________________

DATE OF PURCHASE: _______________________

THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A DECAL ATTACHED TO THE REAR OF THE SNOW THROWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

PRODUCT SPECIFICATIONS

Gasoline Capacity 4.0 Quarts (3,79 Liters) and Type: Unleaded Regular only

Oil Type	SAE 5W-30 or 10W-30
(API SG–SL):	(0° to +40°F)
	SAE 0W-30 (below 0°F)
Oil Capacity:	26 Ounces (0,74 Liters)
Spark Plug:	Champion RN4C
Gap:	0.030" (0,762 mm)

CUSTOMER RESPONSIBILITIES

•Read and observe the safety rules.

•Follow a regular schedule in maintaining, caring for and using your snow thrower.

•Follow the instructions under “Maintenance” and “Storage” sections of this owner’s manual.

TABLE OF CONTENTS

SAFETY RULES ........................................................	2-3
PRODUCT SPECIFICATIONS......................................	3
CUSTOMER RESPONSIBILITIES................................	3
ASSEMBLY / PRE-OPERATION ...............................	4-7
OPERATION ............................................................	8-13
MAINTENANCE SCHEDULE .....................................	14

MAINTENANCE.....................................................	14-15
SERVICE AND ADJUSTMENTS...........................	16-18
STORAGE...................................................................	18
TROUBLESHOOTING................................................	19
REPAIR PARTS .....................................................	20-38
3 WARRANTY...............................................	BACK PAGE

PARTS PACKED SEPARATELY IN CARTON

(1) AUGER CONTROL ROD

(1) TRACTION DRIVE CONTROL ROD

(1) POWER CORD

(198563)

(1) DISCHARGE CHUTE

EXTRA SHEAR BOLTS AND NUTS

							(6) LOCKNUTS
(6) SHEAR BOLTS 1/4-20 x 1-3/4				(6) SPACERS
(198636)				(198638)			1/4-20
							(73800400)

ROTATOR HEAD MOUNTING

(3) RETAINER SPRINGS (169675)

(1) WASHER 3/8	(1) LOCKNUT 3/8
(19131316)	(73800600)

CHUTE DEFLECTOR REMOTE CONTROL

(1) LOCKNUT

(1) CARRIAGE BOLT

(1) LOCKNUT

(1) NYLON

(1) SHOULDER

(1) SPRING

5/16-18

5/16-18 x 5/8

1/4-20

WASHER

BOLT 1/4-20

(751153)

(72250505)

(191730)

(179246)

(179829)

(184505)

(1) SAFTEY IGNITION KEY

(35062)

(1) MULTIWRENCH (180684)

(2)HANDLE KNOBS

(2)CARRIAGE BOLTS 3/8-16 x 2.25

(2)FLAT WASHERS

ASSEMBLY / PRE-OPERATION

	Read these instructions and this manual in its entirety		2.	Cut down all four corners of carton and lay panels flat.
	before you attempt to assemble or operate your new		3.	Remove the two (2) screws securing the auger housing
	snow thrower. Reading the entire manual will familiar-
				to the pallet.
	ize you with the unit, which will assist you in assembly,
			4.	Remove all packing materials except plastic tie holding
	operation and maintenance of the product.
				speed control rod to lower handle.
	Your new snow thrower has been assembled at the factory
			5. Remove the two (2) plastic ties securing the upper
	with the exception of those parts left unassembled for ship-
				handle to the pallet.
	ping purposes. All parts such as nuts, washers, bolts, etc.,
			6. Remove snow thrower from carton and check carton
	necessary to complete the assembly have been placed in
	the parts bag. To ensure safe and proper operation of your			thoroughly for additional loose parts.
	snow thrower, all parts and hardware you assemble must		HOW TO SET UP YOUR SNOW THROWER
	be tightened securely. Use the correct tools as necessary
	to ensure proper tightness.		TOOL BOX (See Fig. 10)
	REMOVE SNOW THROWER FROM CARTON		A toolbox is provided on your snow thrower. The toolbox is
	1. Remove all accessible loose parts and parts boxes		located on top of the belt cover. Store the extra shear bolts,
		4	nuts and multi-wrench provided in parts bag in the toolbox.
	from carton.

ASSEMBLY / PRE-OPERATION

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.

UNFOLD UPPER HANDLE

1.Raise upper handle to the operating position and tighten handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles.

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1.Remove plastic tie securing rod to lower handle.

2.Insert rod into speed control bracket and secure with retainer spring.

SPEED

CONTROL

ROD

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

FIG. 1

SPEED CONTROL ROD
	RETAINER
	SPRING
SPEED	SPEED
CONTROL	CONTROL
BRACKET	LEVER

FIG. 2

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod has the long loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

TRACTION DRIVE

CONTROL ROD

RUBBER

SLEEVE

LOOP

OPENING

DOWN

PIVOT

BRACKET

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING
	TRACTION
	DRIVE
	CONTROL
	ROD
DRIVE
CONTROL
BRACKET

FIG. 4

5

ASSEMBLY / PRE-OPERATION

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

The auger control rod has the short loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown.

2.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

AUGER

CONTROL

ROD

RUBBER

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

FIG. 5

	AUGER CONTROL ROD	AUGER
	RETAINER	CONTROL
		LEVER
	SPRING
		AUGER
	CONTROL
	BRACKET

FIG. 6

INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7)

NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head.

1.Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower.

2.Position chute rotater head over chute bracket. If necessary,rotatechuteassemblytoalignsquareandpinonunderside of chute rotater head with holes in chute bracket.

3.With chute rotater head and chute bracket aligned, position chute rotater head on pin and threaded stud of mounting bracket.

4.Install 3/8 washer and locknut on threaded stud and tighten securely.

CHUTE
ROTATER		3/8 LOCKNUT
HEAD
		3/8 WASHER
		PIN
		THREADED
		STUD
	ALIGN BEFORE	ROTATER HEAD
CHUTE		MOUNTING
BRACKET	TIGHTENING LOCKNUT	BRACKET

FIG. 7

6

ASSEMBLY / PRE-OPERATION

INSTALL CHUTE DEFLECTOR REMOTE CONTROL

(See Figs. 8 and 9)

1.Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely.

2.Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt, nylon washer and 1/4-20 locknut as shown. Tighten securely.

3.Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown.

	1/4-20	SPRING
		CHUTE
	SHOULDER
		DEFLECTOR
	BOLT
		HOOK
	NYLON	BETWEEN
	WASHER	HEX NUTS
		ON CHUTE
	1/4-20	ROTATER
	LOCKNUT	HEAD
		5/16-18
		CARRIAGE
		BOLT
	CABLE
	EYELET
	REMOTE
	CABLE
	BRACKET
	5/16-18
	LOCKNUT

FIG. 8

CHUTE DEFLECTOR

CONTROL LEVER

FIG. 9

CHECK TIRE PRESSURE

The tires on your snow thrower were overinflated at the factory for shipping purposes. Correct and equal tire pressure is important for best snow throwing performance.

•Reduce tire pressure to 14-17 PSI (19-24.5 N-m).

7

OPERATION

KNOW YOUR SNOW THROWER

READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.

These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning.

DANGER										PRIMER

OR WARNING

READ AND FOLLOW ALL SAFETY INFORMATION

AND INSTRUCTIONS BEFORE USE OF THIS PRODUCT. FORWARD REVERSE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

IGNITION KEY.
INSERT TO START
AND RUN,
PULL OUT TO STOP.
DISENGAGED
ENGAGED
SNOW	TRACTION
DISCHARGE	DRIVE CONTROL
	8

OPERATION

SPARK	ENGINE OIL CAP	AUGER
PLUG	WITH DIPSTICK	CONTROL
SAFETY		LEVER

IGNITION
KEY	GASOLINE
	FILLER
	CAP

	CHOKE			CHUTE
				DEFLECTOR
	CON-
	TROL
				FUEL
				SHUT-OFF
				VALVE
	THROTTLE
	/ ENGINE
	CONTROL			DISCHARGE
				CHUTE
	RECOIL	POWER	ELECTRIC
		CORD	START
	STARTER	PLUG
			BUTTON	OIL DRAIN PLUG
	HANDLE
				CLEAN-OUT TOOL
	PRIMER
	NOTE: ITEMS ABOVE
	ARE SHOWN IN
	THEIR TYPICAL
	LOCATION ON THE
	ENGINE. ACTUAL
	LOCATION MAY VARY
	WITH THE ENGINE
	ON YOUR UNIT.

DISCHARGE CHUTE CONTROL LEVER

	DEFLECTOR	TRACTION
DRIVE SPEED	REMOTE
CONTROL LEVER	CONTROL	DRIVE
	LEVER	CONTROL
		LEVER

LH TURN

TRIGGER

LIGHT

HANDLE

KNOB

MUFFLER

TOOLBOX

DRIFT

CUTTER

SKID PLATE AUGERS

FIG. 10

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button – used for starting the engine.

Recoil (auxiliary) starter handle – used for starting the engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Throttle/engine control - used to select either FAST or SLOW engine speed and to STOP the engine.

Choke control - used for starting a cold engine.

LH and RH turn triggers - used to steer the snow thrower.

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Traction drive control lever - used to engage power-pro- pelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Deflector remote control lever - used to change the distance the snow is thrown.

Discharge chute control lever - used to change the direction the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground.

9 Drift cutter - used to cut through deep snowdrifts.

OPERATION

The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear

safety glasses or eye shields while operating your snow thrower or performing any adjustments or repairs. We recommend standard safety glasses

or a wide vision safety mask worn over spectacles.

TO USE CHOKE CONTROL (See Fig. 13)

The choke control is located on the engine. Use the choke control whenever you are starting a cold engine. Do not use to start a warm engine.

•To engage choke, turn knob clockwise. Slowly turn knob counterclockwise to disengage.

	HOW TO USE YOUR SNOW THROWER
	Know how to operate all controls before adding fuel or		OFF			FULL
	attempting to start the engine.
	STOPPING
	TRACTION DRIVE
	• Release traction drive control lever to stop the forward
	or reverse movement of the snow thrower.
	AUGER
				FIG. 13
	• Release the auger control lever to stop throwing snow.		TO CONTROL SNOW DISCHARGE (See Fig. 14)
	ENGINE
			WARNING: Snow throwers have ex-
	1. Move throttle control to “STOP” position.
			posed rotating parts, which can cause
	2. Remove (do not turn) safety ignition key to prevent		severe injury from contact, or from ma-
			terial thrown from the discharge chute.
	unauthorized use.
			Keep the area of operation clear of all
	NOTE: Never use choke to stop engine.
			persons, small children and pets at all
	TO USE FUEL SHUT-OFF VALVE (See Fig. 11)		times including startup.
	The fuel shut-off valve is located beneath the fuel tank on		WARNING: If the discharge chute or
	the engine. Always operate the snow thrower with the fuel		auger become clogged, shut-off engine
	shut-off valve in the OPEN position.		andwaitforallmovingpartstostop.Use
			the clean-out tool, NOT YOUR HANDS,
			to unclog the chute and/or auger.
			The DIRECTION in which snow is to be thrown is controlled
			by the discharge chute control lever.
	OFF		• To change the discharge chute position, press down-
			ward on discharge chute control lever and move lever
			left or right until chute is in desired position. Be sure
			lever springs back and locks into desired position.
	OPEN		The DISTANCE that snow is thrown is controlled by the
			position of the chute deflector. Set the deflector low to
			throw snow a short distance; set the deflector higher to
	FIG. 11
			throw snow farther.
	TO USE THROTTLE CONTROL (See Fig. 12)		• Press downward on chute deflector control lever and
	The throttle control is located on the engine. Always operate		move lever forward to raise the deflector and increase
	the snow thrower with the engine at full throttle. Full throttle		the distance. Move lever back to lower the deflector
	offers the best snow thrower performance.		and decrease the distance. Be sure lever springs back
			and locks into desired position.
	FAST			DISCHARGE CHUTE
				CONTROL LEVER

SLOW

CHUTE DEFLECTOR

REMOTE CONTROL LEVER

FIG. 12

10

FIG. 14

OPERATION

TO THROW SNOW (See Fig. 15)

The auger rotation is controlled by the auger control lever located on the right side handle.

•Squeeze auger control lever to handle to engage the auger and throw snow.

•Release the auger control lever to stop throwing snow.

AUGER

CONTROL

LEVER

FIG. 15

USING THE CLEAN-OUT TOOL (See Fig. 16)

In certain snow conditions, the discharge chute may become clogged with ice and snow. Use the clean-out tool to dislodge this blockage.

When cleaning, repairing, or inspecting, make certain all controls are disengaged and the auger/impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the spark plug to prevent accidental starting.

•Release the auger control lever and shut off the engine.

•Remove the clean-out tool from it's mounting clip. Grasp the tool firmly by the handle and push and twist the tool into the discharge chute to dislodge the blockage.

After the packed snow has been dislodged, return the cleanout tool to it's mounting clip by pushing it into the clip.

•Make sure the discharge chute is pointed in a safe direction (no vehicles, buildings, people, or other objects are in the direction of discharge) before restarting engine.

•Restart the engine, then squeeze the auger control lever to the handle to clear snow from the auger housing and the discharge chute.

DISCHARGE CHUTE
CLEAN-OUT
TOOL
MOUNTING
CLIP
FIG. 16	11

TO MOVE FORWARD AND BACKWARD (See Fig. 17)

SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive control lever located on the left side handle.

•Squeeze traction drive control lever to handle to engage the drive system.

•Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

SPEED and DIRECTION are controlled by the drive speed control lever.

•Press downward on the speed control lever and move lever to desired position BEFORE engaging the traction drive control lever. Be sure lever springs back and locks into desired position.

CAUTION: Do not move speed control lever when traction drive control lever is engaged. Damage to the snow thrower can result.

•Slower speeds are for heavier snow and faster speeds are for light snow and transporting the snow thrower. It is recommended that you use a slower speed until you are familiar with the operation of the snow thrower.

NOTE: When both traction drive and auger control levers are engaged, the traction drive control lever will lock the auger control lever in the engaged position. This will allow you to release your right hand from the handle and adjust the discharge chute direction without interrupting the snow throwing process.

TRACTION DRIVE

CONTROL LEVER

DRIVE SPEED

CONTROL LEVER

FIG. 17

POWER STEERING OPERATION (See Fig. 18)

Steering triggers are used to assist in steering your snow thrower. The triggers are located on the underside of each handle. When a trigger is squeezed, it disengages the drive wheel on that side of snow thrower and allows it to turn in that direction.

•To turn left – squeeze left side trigger.

•To turn right – squeeze right side trigger.

LH TURN	RH TURN
TRIGGER	TRIGGER

FIG. 18

OPERATION

	TO ADJUST SKID PLATES (See Fig. 19)	BEFORE STARTING THE ENGINE
	NOTE: The wrench provided in your parts bag may be	CHECK ENGINE OIL LEVEL (See Fig. 21)
	used to adjust the skid plates.	The engine on your snow thrower has been shipped, from
	Skid plates are located on each side of the auger housing	the factory, already filled with oil.
	and adjust the clearance between the scraper bar and the	1.	Check engine oil with snow thrower on level ground.
	ground surface. Adjust skid plates evenly to proper height
		2.	Remove oil fill cap/dipstick and wipe clean, reinsert
	for current surface conditions. For removal of snow in
			the dipstick and screw tight, wait for a few seconds,
	normal conditions, such as a paved driveway or sidewalk,
			remove and read oil level. If necessary, add oil until
	place skid plates in the highest position (lowest scraper
			“FULL” mark on dipstick is reached. Do not overfill.
	clearance) to give a 1/8" clearance between the scraper
		•	To change engine oil, see “TO CHANGE ENGINE OIL”
	bar and the ground. Use a middle position if the surface
	to be cleared is uneven.		in the Maintenance section of this manual.

	NOTE: It is not recommended to operate the snow thrower		ADD GASOLINE (See Fig. 21)
	over gravel or rocky surfaces. Objects such as gravel, rocks		• Fill fuel tank to bottom of tank filler neck. Do not over-
	or other debris, can easily be picked up and thrown by the
			fill. Use fresh, clean, regular unleaded gasoline with
	impeller, which can cause serious personal injury, property		a minimum of 87 octane. Do not mix oil with gasoline.
	damage or damage to the snow thrower.		Purchase fuel in quantities that can be used within 30
	• If snow thrower must be operated over gravel surface,		days to assure fuel freshness.
	use extra caution and be sure skid plates are adjusted
	to lowest (highest scraper clearance) position.		WARNING: Wipe off any spilled oil or
	1. Shut off engine and wait for all moving parts to stop.
			fuel. Do not store, spill or use gasoline
	2. Adjust skid plates by loosening the hex nuts, then mov-		near an open flame.
	ing skid plate to desired position. Be sure both plates
	are adjusted evenly. Tighten securely.		CAUTION: Alcohol blended fuels (called gaso-
	HIGH POSITION		hol or using ethanol or methanol) can attract
	(LOW GROUND	HEX	moisture which leads to separation and forma-
	CLEARANCE)	NUTS	tion of acids during storage. Acidic gas can
		AUGER	damage the fuel system of an engine while in
			storage. To avoid engine problems, the fuel
		HOUSING
	LOW POSITION	SCRAPER	system should be emptied before storage of
			30 days or longer. Empty the gas tank, start
	(HIGH GROUND
		BAR	the engine and let it run until the fuel lines
	CLEARANCE)	SKID PLATE
			and carburetor are empty. Use fresh fuel next
			season. See Storage Instructions for additional
	FIG. 19		information. Never use engine or carburetor
			cleaner products in the fuel tank or permanent
	SCRAPER BAR (See Fig. 19)		damage may occur.

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn

almost to the edge of the housing, it can be reversed,	CHOKE CONTROL	THROTTLE PRIMER ENGINE OIL
providing additional service before requiring replacement.		FILL CAP /
Replace a damaged or worn scraper bar.		DIPSTICK
TO USE DRIFT CUTTERS (See Fig. 20)	SAFETY
Use the drift cutters to cut through deep snowdrifts that
	IGNITION
are higher than the front of the snow thrower.	KEY

• Loosen adjustment nuts enough to allow drift cutter to be raised to highest position and tighten nuts securely. Repeat for opposite side of snow thrower.

• When not using drift cutters, loosen adjustment nuts, lower to storage position and tighten nuts securely.

AUGER				GASOLINE
HOUSING
				FILLER CAP
STORAGE		DRIFT		FUEL SHUT-
POSITION		CUTTER		OFF VALVE
			RECOIL	STARTER BUTTON
			STARTER
			HANDLE	POWER CORD PLUG
		ADJUST-	NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION.
		MENT NUTS	ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.
	FIG. 20	12		FIG. 21