Husqvarna 128LD-LOWES, 128LD, 128CD-LOWES, 128CD Owner’s Manual
Operator's manual
Manuel d'utilisation
Manual de instrucciones
128CD 128LD
Please read these instructions and make sure you understand them before using the machine.
Life attentivement et bien assimiler le manuel d'utilisation avant d'utiliser la machine.
Lea detenidamente el manual de instrucciones y aseg_rese de entender su contenido antes de utilizar la m_quina.
EN (2-25)
FR (26-49)
ES (50-75)
CONTENTS
Contents
CONTENTS
Contents ........................ 2
Note the following before starting .... 2
KEY TO SYMBOLS
Symbols ......................... 3
SAFETY INSTRUCTIONS
Personal protective equipment ...... 4
Machine's safety equipment ........ 4
Cutting equipment ................. 5
Checking, maintaining and servicing
the machine's safety equipment ..... 5
General safety precautions ......... 8
Starting ......................... 9
Fuel safety ....................... 9
Transporting and storage ........... 9
General working instructions ........ 9
Basic safety rules ................. 9
Basic working techniques .......... 10
KNOW YOUR TRIMMER
Know your trimmer ................ 12
ASSEMBLY
Fitting the loop handle ............. 13
Assembling and dismantling the
two-piece shaft ................... 13
Fitting the trimmer guard and
trimmer head ..................... 13
FUEL HANDLING
Fuel ............................ 15
Fueling .......................... 15
STARTING AND STOPPING
Check before starting .............. 16
Starting and stopping .............. 16
MAINTENANCE
Carburetor ....................... 18
Muffler .......................... 18
Spark plug ....................... 19
Two-piece shart .................. 19
Air filter .......................... 19
Bevel gear ....................... 19
Maintenance schedule ............. 20
Trimmer head line loading instructions .. 21
TECHNICAL DATA
Technical data .................... 22
WARRANTY STATEMENT ......... 23
EMISSION CONTROL
WARRANTY STATEMENT ......... 24
Note the following before
starting:
Husqvarna AB has a policy of continuous
product development and therefore
reserves the right to modify the design and
appearance of products without prior
notice. Long-term exposure to noise can
result in permanent hearing impairment.
Always use approved hearing protection.
Maintenance, replacement, or repair of the
emission control devices and system may
be performed by any nonroad engine re-
pair establishment or individual.
The Emissions Compliance Period referred
to on the Emissions Compliance label indi-
cates the number of operating hours for
which the engine has been shown to meet
Federal emissions requirements.
545186844 Rev. 5 2/17/09
Category C = 50 hours, B= 125 hours, and
A = 300 hours.
WARNING
Theengine exhaust fromthisproduct
contains chemicalsknownto the State
ofCalifornia to causecancer,birth
defectsor other reproductiveharm.
For reference, please fill out the following
information that will be needed for future
servicing of your trimmer:
Model Number:
Serial Number:
Purchase Date:
Purchased From:
WARNING: Aclearingsaw,
bruahcutter or trimmer can be
dangerous if used incorrectly or
carelessly, and can cause serious
or fatal injury to the operator or
others. It is extremely important
that you read and understand the
contents of this operator's manual.
WARNING: Under no circum-
stances may the design of the
machine be modified without the
permission of the manufacturer.
Always use genuine accessories.
Non-authorized modifications
and/or accessories can result
in serious personal injury or the
death of the operator or others.
Your warranty may not cover
damage or liability caused by the
use of non-authorized accesso-
ries or replacement parts.
For customer assistance, call:
1-800-487-5951
Contact us at our website:
www, husqvarna,oom
English-2
KEY TO SYMBOLS
Symbols
WARNING: Clearing saws, brush- A
cutters and trimmers can be dan- /|_
gerous! Careless or incorrect use / _ '_
can result in serious or fatal
injury to the operator or others.
Please read the operator's manual
carefully and make sure you
understand the instructions
before using the machine.
• Hearing protection
Always wear: @
• Approved eye protection
Max. speed of output shaft, rpm d
max
10000 rprn
Watchricochets.OUtfor thrown objects and ,i_
Only intended for trimmer heads, i_
Use unleaded or quality leaded \_
gasoline and two-stroke oil
mixed at a ratio of 2% (1:50).
Other symbols/decals on the machine
refer to special certification requirements
for certain markets.
Stop the engine by pushing
and holding the stop switch
in the STOP position until the
engine stops before carrying
out any checks or maintenance.
The operator of the machine
must ensure, while working,
that no persons or animals
come closer than 50 feet
(15 meters).
Arrows which show limits for
handle positioning.
Always wear approved protective
gloves.
Regular cleaning is required.
Visual check.
Approved eye protection must
always be used.
U
Wear sturdy, non-slip boots.
Only use non-metallic, flexible
cutting attachments, i.e. trimmer
heads with trimmer line.
545186844 Rev. 5 2/17/09 English-3
SAFETY INSTRUCTIONS
Personal protective equipment
IMPORTANT! Whenever you use a clear-
ing saw, brushcutter or trimmer you must
wear personal protective equipment that is
approved by the authorities. Personal
protective equipment does not eliminate
the risk of accidents, but it can reduce the
effects of an injury in the event of an acci-
dent. Ask your dealer for help when
choosing protective equipment.
WARNING: Listen out for warn-
ing signals or shouts when you are
wearing hearing protection. Always
remove your hearing protection as
soon as the engine stops.
GLOVES
Gloves should be worn when necessary,
e.g., when fitting cutting attachments.
HEARING PROTECTION
Wear hearing protection that provides
adequate noise reduction.
EYE PROTECTION
Always wear approved eye protection. If
you use a visor then you must also wear
approved protective goggles. Approved
protective goggles must comply with
standard ANSI Z87.1.
FIRST AID KIT
Always have a first aid kit nearby.
Machine's safety equipment
This section describes the machine's safe-
ty equipment, its purpose, and how checks
and maintenance should be carried out to
ensure that it operates correctly. See the
"Know your trimmer" section to locate
where this equipment is positioned on your
machine.
The life span of the machine can be reduced
and the risk of accidents can increase if
machine maintenance is not carried out
correctly and if service and/or repairs are not
carried out professionally. If you need further
information please contact your nearest ser-
vicing dealer.
WARNING: Never use a machine
that has faulty safety equipment[
Carry out the inspection, mainte-
nance and service routines listed in
this section.
Throttle lock-out
The throttle lock-out is designed to prevent
accidental operation of the throttle control.
When you press the lock-out (A) (i.e. when
you grasp the handle) it releases the
throttle control (B). When you release the
handle the throttle control and the throttle
lock-out both move back to their original
positions. This movement is controlled by
two independent return springs. This ar-
rangement means that the throttle control is
automatically locked at the idle setting.
A
BOOTS
Wear sturdy, non-slip boots.
Stop switch
Make sure the engine stops when you push
and hold the stop switch.
CLOTHING
Wear clothes made of a strong fabric and
avoid loose clothing that can catch on
twigs and branches. Always wear heavy,
long pants. Do not wear jewelry, shorts
sandals or go barefoot. Secure hair so it is
above shoulder level.
545186844 Rev. 5 2/17/09 English-4
SAFETY INSTRUCTIONS
Cutting attachment guard
This guard is intended to prevent loose ob-
jects from being thrown towards the opera-
tor. The guard also protects the operator
from accidental contact with the cutting at-
tachment.
attachment without an approved
guard. See the section on "Technical
data". If an incorrect or faulty guard
is fitted this can cause serious
_ ARNING: Never use a cutting
personal injury.
Use of incorrectly wound trimmer line or an
incorrect cutting attachment increases the
level of vibration.
WARNING: Overexposure to
vibration can lead to circulatory
damage or nerve damage in people
who have impaired circulation.
Contact your doctor if you experi-
enca symptoms of overexposure to
vibration. Such symptoms include
numbness, loss of feeling, tingling,
pricking, pain, loss of strength,
changes in skin color or condition.
These symptoms normally appear
in the fingers, hands or wrists. The
risk increases at low temperatures.
Muffler
The muffler is designed to reduce the noise
level and to direct the exhaust gases away
from the operator.
CAUTION! Muffler is fitted with a catalytic
converter designed to reduce harmful ex-
haust gases.
For mufflers, it is very important that you fol-
low the instructions on checking, maintain-
ing, and servicing your machine.
See Checking, maintaining and servicing the
machine's safety equipment section.
WARNING: Mufflers fitted with
&
catalytic converters get very hot
during use and remain so for some
time after stopping. This also ap-
plies at idle speed. Contact can re-
sult in burns to the skin. Remember
the risk of fire!
WARNING: The inside of the
muffler contain chemicals that may
be carcinogenic. Avoid contact with
these elements in the event of a
&
damaged muffler.
WARNING: Bear in mind that:
M
Engine exhaust fumes contain car-
bon monoxide, which can cause
carbon monoxide poisoning. For
this reason you should not start or
run the machine indoors, or any-
where that is poorly ventilated.
The exhaust fumes from the engine
are hot and may contain sparks
which can start a fire. Never start
the machine indoors or near com-
bustible material!
Cutting equipment
A trimmer head is intended for trimming
grass.
Checking, maintaining and
servicing the machine's
safety equipment
IMPORTANT!
All servicing and repair work on the machine
requires special training. This is especially
true of the machine's safety equipment. If
your machine fails any of the checks de-
scribed below you must contact your service
agent. When you buy any of our products we
guarantee the availability of professional re-
pairs and service. If the retailer who sells
your machine is not a servicing dealer, ask
him for the address of your nearest service
agent.
545186844 Rev. 5 2/17/09 English-5
SAFETY INSTRUCTIONS
Throttle lock-out
• Make sure the throttle control is locked
at the idle setting when the throttle lock-
out is released.
• Press the throttle lock-out and make
sure it returns to its original position
when you release it.
• Check that the throttle control and
throttle lock-out move freely and that the
return springs work properly.
Stop switch
• Start the engine and make sure the engine
stops when you push and hold the stop
switch.
Cutting attachment guard
• Ensure that the guard is undamaged and
is not cracked.
• Replace the guard if it has been exposed
to impact or is cracked.
• Always use the recommended guard for
the cutting attachment you are using. See
section on "Technical data".
Muffler
• Never use a machine that has a faulty
muffler.
• See instructions under the section
"Start". Start the machine and apply full
throttle. Release the throttle and check
that the cutting attachment stops and re-
mains at a standstill. If the cutting attach-
ment rotates with the throttle in the idle
position then the carburetor idle setting
must be checked. See instructions under
the section "Maintenance".
545186844 Rev. 5 2/17/09 English-6
• Regularly check that the muffler is securely
attached to the machine.
• The muffler on this unit is equipped with a
special spark arrestor mesh. The mesh
should be checked and, if necessary.
cleaned by a servicing dealer. A blocked
mesh will cause the machine to overheat,
which can lead to serious damage. Never
use a muffler with a defective spark arres-
tor mesh. See the Maintenance section.
@
SAFETY INSTRUCTIONS
Cutting equipment
This section describes how to choose and
maintain your cutting equipment in order to:
• Obtain maximum cutting performance.
• Extend the life d cutting equipment.
General rules:
Trimmer head
• Only use the recommended cutting at-
tachments. See the section on "Technical
data".
1. Only use cutting attachments with the
guards we recommend! See the section
on "Technical Data".
2. Check the cutting attachment for damage
or cracks. A damaged cutting attachment
should always be replaced.
WARNING: Never use a machine
with faulty safety equipment. The
machine's safety equipment must be
checked and maintained as
described in this section.
If your machine fails any of these
checks contact your service agent to
get t repa red,
IMPORTANT!
This section describes how to choose and
maintain your cutting equipment in order to:
Obtain maximum cutting performance.
Extend the life of cutting equipment.
Only use cutting attachments with the guards
we recommend! See the section on
"Technical data".
Refer to the instructions for the cutting attach
ment to check the correct way to load the
trimmer line and the correct line diameter.
• Smaller machines generally require small
trimmer heads and vice versa. This is be-
cause when clearing using trimmer line
the engine must throw out the trimmer
line radially from the trimmer head and
overcome the resistance of the grass
being cleared.
• The length of the trimmer line is also im-
portant. A longer trimmer line requires
greater engine power than a shorter
trimmer line of the same diameter.
• Make sure that the cutter on the trimmer
guard is intact. This is used to cut the
trimmer line to the correct length.
• To increase the life of the trimmer line it
can be soaked in water for a couple of
days. This will make the line tougher so
that it lasts longer.
IMPORTANT!
Always ensure the trimmer line is wound
tightly and evenly around the drum, other-
wise the machine will generate harmful
v brat on.
WARNING: Always stop the en-
gine before doing any work on the
cutting attachment. This continues
to rotate even after the throttle has
been released, Ensure that the
cutting attachment has stopped
completely and disconnect the
lead from the spark plug before
you start to work on it,
545186844 Rev. 5 2/17/09 English-7
SAFETY INSTRUCTIONS
General safety precautions
IMPORTANT!
• The machine is only designed for trimming
grass.
• The only accessories you can operate
with this engine unit are the cutting at-
tachments we recommend in the "Tech-
nical data" section.
• Never use wire, rope, string, etc.
• Never use the machine if you are tired, if
you have drunk alcohol, or if you are tak-
ing medication that could affect your vi-
sion, your judgment or your coordination.
• Never use the machine in extreme weath-
er conditions such as severe cold, very hot
and/or humid climates.
• Never use a machine that has been modi-
fied in any way from its original specifica-
tion.
• Wear personal protective equipment. See
instructions in the "Personal protective
equipment" section.
• Never use a machine that is faulty. Carry
out the checks, maintenance and service
instructions described in this manual.
Some maintenance and service measures
must be carried out by trained and quali-
fied specialists. See instructions in the
"Maintenance" section.
• All covers and guards must be fitted before
starting. Make sure the spark plug cap and
lead are not damaged. Otherwise you
could get an electric shock.
• The machine operator must ensure that
no people or animals come closer than
50 feet (15 meters) while working.
• Stay clear of spinning line.
• Secure or remove loose clothing or cloth-
ing with loosely hanging ties, straps, tas-
sels, etc. They can be caught in moving
parts.
• Being fully covered also helps protect you
from debris and pieces of toxic plants
thrown by spinning line.
• Keep handles free of oil and fuel.
• Always keep the engine on the right hand
side of your body.
• Hold the unit firmly with both hands.
• Keep trimmer head below waist level and
away from all parts of your body. Do not
raise engine above your waist.
• Keep all parts of your body away from
muffler and spinning line. Keep engine be-
low waist level. A hot muffler can cause
serious burns.
• Keep firm footing and balance. Do not
overreach or use from unstable surfaces
such as ladders, trees, steep slopes, roof-
tops, etc.
• Use only in daylight or good artificial light.
• Use only for jobs explained in this manual.
tachment may increase the risk of
WARNING: A faulty cutting at- ]
accidents.
Personal protection
@@@
• Always wear boots and
other equipment described
in the "Personal protective
equipment" section.
• Always wear working
clothes and heavy-duty
long pants.
• Never wear loose fitting
clothes or jewelry.
• Persons with long hair
should (for personal safety)
put their hair up.
Safety instructions regarding the
surroundings
• Never allow children to use the machine.
• Ensure no one comes closer than 50 feet
(15 meters) when working.
• Never allow anyone else to use the
machine without first ensuring that they
have understood the contents of the
operator's manual.
Safety instructions before starting
work
• Inspect the working area. Remove any
objects such as stones, broken glass,
nails, steel wire, string, etc. that can be
thrown or can wrap around the cutting
head or shaft.
• Keep others at a safe distance. Children,
animals, onlookers and helpers should
stand outside of the safety zone of 50
feet (15 meters). Bystanders should be
encouraged to wear safety glasses. Stop
the machine immediately if anyone
should approach.
• Check the entire machine before starting
work. Replace damaged parts. Check for
fuel leakage and that all safety guards
and covers are complete and fastened
securely. Check all nuts and bolts.
• Check the cutting head _'_\
for cracks or any other _\ _._
damage.
Ensure the trimmer guard iV _j
is mounted and not _l_J
damaged.
545186844 Rev. 5 2/17/09 English-8
SAFETY INSTRUCTIONS
• Check that the trimmer head and guard
are correctly secured.
• When adjusting the carburetor, make sure
the lower end is supported and that no one
is in the immediate vicinity.
• Make sure the cutting head does not rotate
when idling.
• Make sure the handle and safety features
are in order. Never use a machine that has
parts missing or has been changed in
relation to the specification.
• Only use the machine for the purpose for
which it was intended.
Starting
WARNING: When the is
started with the choke in either the
choke or start throttle positions the
cutting attachment will start to
rotate immediately.
• Ensure that all of the engine covers and
housings are properly fitted before the unit
is started.
• Never start or attempt to run the unit with
the clutch, clutch drum, clutch cover, or
driveshaft removed.
• Never start the machine indoors. Exhaust
fumes can be dangerous if inhaled.
• Observe your surroundings and make sure
that there is no risk of people or animals
coming into contact with the cutting equip-
ment.
• See the "Starting and Stopping" section for
complete instructions.
engine
Fuel safety
• Always use a fuel container with an anti-
spill valve.
• Never refuel the machine while the engine
is running.
• Always stop the engine and let it cool for a
few minutes before refueling.
• Make sure there is plenty of ventilation
when refueling or mixing fuel (gasoline and
2-stroke oil).
• Move the machine at least 10 feet (3 me-
ters) from the refueling point before start-
ing_it. '===ll_ I_
=_' _ (3 m)
545186844 Rev. 5 2/17/09 English-9
Min. 10ft.
• Never start the machine:
• If you have spilled fuel on it. Wipe off
the spillage and allow remaining fuel to
evaporate.
• If you have spilled fuel on yourself or
your clothes, change your clothes. Wash
any part of your body that has come in
contact with fuel. Use soap and water.
• If the machine is leaking fuel. Check
regularly for leaks from the fuel cap
and fuel lines.
• Avoid all skin contact with fuel. Fuel is
a skin irritant and may even cause
skin changes.
Transporting and storage
• Store and transport the machine and fuel
so that there is no risk of any leakage or
fumes coming into contact with sparks or
naked flames, for example, from electri-
cal machinery, electric motors, electrical
relays/switches or boilers.
• When storing and transporting fuel al-
ways use approved containers intended
for this purpose.
• When storing the machine for long peri-
ods the fuel tank must be emptied. Con-
tact your local gas station to find out
where to dispose of excess fuel.
dling fuel. Bear in mind the risk of
WARNING: Take care when han- ]
fire, explosion and inhaling fumes.
General working instructions
IMPORTANT!
This section describes the basic safety pre-
cautions for working with trimmers. If you
encounter a situation where you are uncer-
tain how to proceed you should ask an ex-
pert. Contact your servicing dealer.
Avoid all usage which you consider to be
beyond your capability.
You must understand the difference between
forestry clearing, grass clearing and grass
trimming before use.
Basic safety rules
/kQOO
1. Look around you:
• To ensure that people, animals or other
things cannot affect your control of the
machine.
• To ensure that people, animals, etc.,
do not come into contact with the cut-
ting attachment or loose objects that
are thrown out by the cutting attach-
ment.
SAFETY INSTRUCTIONS
• CAUTION! Do not use the machine
unless you are able to call for help in
the event of an accident.
2. Do not use the machine in bad weather,
such as dense fog, heavy rain, strong
wind, intense cold, etc. Working in bad
weather is tiring and often brings added
risks, such as icy ground, unpredictable
felling direction, etc.
3. Make sure you can move and stand safely.
Check the area around you for possible ob-
stacles (roots, rocks, branches, ditches, etc.)
in case you have to move suddenly. Take
great care when working on sloping ground.
4. Switch off the engine before moving to
another area.
5. Never put the machine down with the engine
running.
Basic working techniques
• Always slow the engine to idle speed after
each working operation. Long periods at
full throttle without any load on the engine
can lead to serious engine damage.
• It is recommended that the engine not
be operated for longer than 1 minute at
full throttle.
or grass get caught between the
guard and cutting attachment.
_ ARNING: Sometimes branches
Always stop the engine before
cleanin_l.
Grass trimming using a trimmer head
Trimming
QOO
• Hold the trimmer head just above the
ground at an angle. It is the end of the trim-
mer line that does the work. Let the trim-
mer line work at its own pace. Never press
the trimmer line into the area to be cut.
• Reduce the risk of damaging plants by
shortening the trimmer line to 4-4 1/2 inches
(10-12 cm) and reducing the engine speed.
• When trimming you should use less than
full throttle so that the trimmer line lasts
longer and to reduce the wear on the
trimmer head.
Clearing
QOO
• The clearing technique removes all un-
wanted vegetation. Keep the trimmer
head just above the ground and tilt it. Let
the end of the trimmer line strike the
ground around trees, posts, statues and
the like. CAUTION! This technique
increases the wear on the trimmer line.
• The trimmer line wears quicker and must
be fed forward more often when working
against stones, brick, concrete, metal
fences, etc., than when coming into con-
tact with trees and wooden fences.
Cutting
Q00
• The trimmer is ideal for cutting grass that
is difficult to reach using a normal lawn
mower. Keep the trimmer line parallel to
the ground when cutting. Avoid pressing
the trimmer head against the ground as
this can ruin the lawn and damage the
tool.
Do not allow the trimmer head to con-
stantly come into contact with the ground
during normal cutting. Constant contact
of this type can cause damage and wear
to the trimmer head.
• The trimmer line can easily remove grass
and weeds up against walls, fences, trees
and borders, however it can also damage
sensitive bark on trees and bushes, and
damage fence posts.
545186844 Rev. 5 2/17/09 English-lO
SAFETY INSTRUCTIONS
• The fan effect of the rotating line can be
used for quick and easy clearing up,
Hold the trimmer line parallel to and
above the area to be swept and move
the tool to and fro.
/
/
\
• When cutting and sweeping you should
use full throttle to obtain the best results.
WARNING: Neither the operator
&
of the machine nor anyone else may
attempt to remove the cut material
while the engine is running or the
trimmer line is rotating, as this can
result in serious injury. Stop the
engine and trimmer head before you
remove material that has wound
around the drive shaft as otherwise
there is a risk of injury. The bevel
gear can get hot during use and may
remain so for a while afterwards. You
could get burned if you touch it.
WARNING: Watch out for thrown
&
objects. Always wear eye protection.
Never lean over the cutting attach-
ment guard. Stones, rubbish, etc.
can be thrown up into the eyes
causing blindness or serious injury.
Keep unauthorized persons at a dis-
tance. Children, animals, onlookers
and helpers should be kept outside
the safety zone of 50 feet (15 meters).
Stop the machine immediately if
anyone approaches.
545186844 Rev. 5 2/17/09 English-11
\,
Know your trimmer
1. Trimmer head
2. Grease filler cap
3. Bevel gear
4. Cutting attachment guard
5. Upper shaft
6. Lower shaft
7. Loop handle
8. Throttle control
9. Stop switch
10.Throttle lock-out
12. Starter handle
13. Fuel tank
14. Choke control
15. Primer bulb
16. Air filter cover
17. Handle adjustment
18. Drive disc
19. Shaft coupling
20. 2-stroke engine oil
21. Operator's manual (EPA)
11. Cylinder cover
545186844 Rev. 5 2/17/09 English-12
ASSEMBLY
NOTE: Make sure unit is assembled cor-
rectly as shown in this manual.
Fitting the loop handle
• Position the handle on the upper shaft.
Note that the handle must be mounted
between the two arrows on the shaft.
Dismantling:
• Loosen the coupling by turning the knob.
I
• Fit the screw, securing plate and wing
nut as shown in the diagram.
• Tighten the wing nut.
Assembling and dismantling
the two-piece shaft
Assembly:
• Loosen the coupling by turning the knob.
• Position locking/release button (A) of
attachment into guide recess (B) of
coupling.
• Push the attachment into the coupling
until the locking/release button snaps
into the primary hole (C).
• Before using the unit, tighten the knob
securely.
B
Press and hold the locking/release but-
ton (A).
While securely holding the engine and
upper shaft, pull the attachment straight
out of the coupling.
Fitting the trimmer guard and
trimmer head (Model 128LD)
• Fit the correct trimmer guard (D) for use
with the trimmer head. Hook the trimmer
guard/combination guard onto the fitting
on the shaft and secure with the bolt (E).
I_ " E /F
i
D D
• Fit the drive disc (F) on the output shaft.
• Turn the shaft until one of the holes in the
drive disc aligns with the corresponding
hole in the gear housing.
• Insert hex wrench (G) in the hole to lock
the shaft.
• Screw on the trimmer head (H) in the op-
posite direction to the direction of rota-
tion.
H
designed to be used in the primary
hole unless otherwise stated in the
applicable attachment instruction
manual. Using the wrong hole could
I& WARNING: All attachments are
lead to serious injury or damage to
the unit,
545186844 Rev. 5 2/17/09
i
• To dismantle, follow the instructions in
the reverse order.
English - 13
ASSEMBLY
Fitting the trimmer guard and
trimmer head (Model 128CD)
0
• Fit the correct trimmer guard (A) for use
with the trimmer head. Hook the trimmer
guard/combination guard onto the fitting on
the shaft and secure with the wing nut (B).
\\\ jB "IL_/I
c.......÷ ÷
• Fit the dust cup (C) on the shaft. The nut
must be completely covered by the dust
cup.
• Hold the dust cup with a wrench to pre-
vent the shaft from rotating.
• Screw the trimmer head (D) onto the
shaft.
• To dismantle, follow the instructions in
the reverse order.
545186844 Rev. 5 2/17/09 English-14
FUEL HANDLING
Fuel mixture
CAUTION! The machine is equipped with
a two-stroke engine and must always be
run using a mixture of gasoline and two-
stroke engine oil. It is important to accu-
rately measure the amount of oil to be
mixed to ensure that the correct mixture is
obtained. When mixing small amounts of
fuel, even small inaccuracies can drastical-
ly affect the ratio of the mixture.
there is adequate ventilation when
&WARNING: Always ensure
handling fuel.
Gasoline
CAUTION! Always use high quality
unleaded gasoline.
• This engine is certified to operate on
unleaded gasoline.
• The lowest recommended octane rating
is 87. If you run the engine on lower oc-
tane rating than 87, "knocking" can oc-
cur. This leads to an increased engine
temperature, which can result in a seri-
ous engine breakdown.
• When working at continuous high revs a
higher octane rating is recommended.
Two-stroke oil
• For great results and performance use
HUSQVARNA two-stroke oil, which is
specially formulated for our two-stroke
engines. Mixture 1:50 (2%).
• To maximize the life of your trimmer, you
may choose to use a high quality syn-
thetic oil formulated for two-stroke
engines. Mixture 1:50 (2%).
• Never use two-stroke oil intended for
water-cooled outboard engines,
sometimes referred to as outboard oil.
• Never use oil intended for four-stroke
engines.
Gasoline
U.S. gallon
1
21/2
5
Mixing
• Always mix the gasoline and oil in a
clean container intended for fuel.
545186844 Rev. 5 2/17/09 English-15
Two-stroke oil
2% (1:50)
U.S. fl. oz.
21/2
61/2
127/8
• Always start by filing half the amount of the
gasoline to be used. Then add the entire
amount of oil. Mix (shake) the fuel mixture.
Add the remaining amount of gasoline.
• Mix (shake) the fuel mixture thoroughly
before filling the machine's fuel tank.
• Do not mix more than one month's sup-
ply of fuel at a time.
• If the machine is not used for some time,
the fuel tank should be emptied and
cleaned.
WARNING: The catalytic con-
verter muffler gets very hot during
and after use. This also applies
during idling. Be aware of the fire
hazard, especially when working
near flammable substances and/or
vapors.
Fueling
WARNING: Taking the following
precautions, will lessen the risk of
fire:
Do not smoke or place hot objects
near fuel.
Always shut off the engine before
refueling.
Always stop the engine and let it
cool for a few minutes before refu-
elling.
When refueling, open the fuel cap
slowly so that any excess pressure
is released gently.
Tighten the fuel cap carefully after
refueling.
Always move the machine away
from the refueling area before
starting.
• Clean the area around the fuel cap.
Contamination in the tank can cause
operating problems.
• Ensure that the fuel is well mixed by shak-
ing the container before filling the tank.
STARTING AND STOPPING
Check before starting
• Inspect the unit before each use. Re-
place damaged parts. Check for fuel
leaks. Make sure all fasteners are in
place and secure. Make sure the cutting
attachment is properly installed and se-
curely fastened. Use only flexible, non-
metallic line recommended by the
manufacturer. Never use, for example,
wire or wire rope, which can break off
and become a dangerous projectile.
• Check that the trimmer head and trimmer
guard are not damaged or cracked.
Replace the trimmer head or trimmer
guard if they have been exposed to
impact or are cracked.
• Never use the machine without a guard
nor with a defective guard.
Starting and stopping
QOO
WARNING: The complete clutch,
clutch cover, and shaft must be
fitted before the machine is started,
otherwise parts could come loose
and cause personal injury.
Always move the machine away
from the refueling area before
starting. Place the machine on a
flat surface. Ensure the cutting at-
tachment cannot come into contact
with any object.
Make sure no unauthorized persons
are in the working area, otherwise
there is a risk of serious personal
injury. The safety distance is 50 feet
(15 meters).
Cold engine
Primer bulb: Press the primer bulb 10
times until fuel begins to fill the bulb. The
primer bulb need not be completely filled.
',\\ y-
Choke: Move the blue engine choke lever
to the closed position.
/ t
\_', i
I _ '_',t!.,i J
J ¢C)t¢_ JY
Starting
Hold the body of the machine on the
ground using your left hand (CAUTION!
Not with your foot!).
Firmly grip the starter rope handle with
your right hand. DO NOT squeeze
throttle trigger, Slowly pull out the cord
until you feel some resistance (the starter
pawls grip); then quickly and powerfully
pull the cord.
Never wrap the starter cord around
your hand.
Repeat pulling the cord until the engine
attempts to start. Move the blue engine
choke lever to the 1/2position. Pull starter
rope until engine runs. Move the blue en-
gine choke lever to the opened position.
/ t
} _ '_',t!.,i J
NOTE; If engine dies, return blue engine
choke lever to the closed position and
repeat starting steps.
CAUTION! Do not pull the starter cord all
the way out and do not let go of the starter
handle when the cord is fully extended.
This can damage the machine.
545186844 Rev. 5 2/17/09 English-16
Loading...