Husqvarna 125LD Owner’s Manual

EN Operator's manual, pp. 2-24

Please re_d these instructions _nd mak_ _ure you unders_nd them b_fo_ using the m_ch_e

FR Manuel d'utilisation, pp. 25-47

Life atten_vement et bien _s_imiler le manuel d'utillsation _wnt d'utiliser [a machine

ES Manual de instrucciones, pp. 48-71

L_ dg_n_d_men_e el mm_ual de i_s_ucc_ones y ase_rese de engender su conten_do antes de u_izar _a maquma

125LD( )

EN FR ES

CONTENTS

Contents

CONTENTS

Conteets ........................ 2

Note the following before starting .... 2

KEY TO SYMBOLS

Symbols ......................... 3

SAFETY INSTRUCTIONS

Personal protective equipment ...... 4

Machine's safety equipment ........ 4

Cutting equipment ................. 5

Checking, maintaining and servicing

the machine's safety equipment ..... 5

General safety precautions ......... 8

Starting ......................... 9

Fuel safety ....................... 9

Transporting and storage ........... 9

General working instructions ........ 9

Basic safety rules ................. 9

Basic working techniques .......... 10

KNOW YOUR TRIMMER

Know your trimmer ................ 12

ASSEMBLY

Fitth_g the loop handle ............. 13

Assembling and dismantling the

two-piece shaft ................... 13

Fitting the trimmer guard and

trimmer head ..................... 13

FUEL HANDLING

Fuel ............................ 14

Fuelh_g .......................... 14

STARTING AND STOPPING

Check before starting .............. 15

Starting and stopping .............. 15

MAINTENANCE

Carburetor ....................... 17

Muffler .......................... 17

Spark plug ....................... 18

Two-piece shart .................. 18

Air filter .......................... 18

Bevel gear ....................... 19

Maintenance schedule ............. 19

Trimmer head line loading instructions.. 20 TECHNICAL DATA

Technica_ data .................... 21

WARRANTY STATEMENT ......... 22

EMISSION CONTROL

WARRANTY STATEMENT ......... 23

Note the following before

starting:

Husqvarna AB has a policy of continuous

product development and therefore reserves the right to modify the design and

appearance of products without prior notice. Long-term exposure to noise can result in permanent hearing impairment.

Always use approved heating protection. Maintenance, replacement, or repair of the

emission control devices and system may be performed by any nonroad engine re- pair establishment or individual

The Emissions Compliance Period referred to on the Emissions Compliance label indi-

cates the number of operating hours for which the engine has been shown to meet

Federal emissions requirements. Category C = 50 hours, B= 125 hours, and

A = 300 hours.

41 t il I III I

-& WARNING

Theengine exhaustfromthisproduct

containschemicalsknowntotheState

ofCaliforniatocausecancer,birth

defectsorother reproductiveharm.

For reference, please fill out the following information that will be needed for future

servicing of your trimmer:

Model Number:

Serial Number:

Purchase Date:

Purchased From:

WARNING: A clearing saw,

brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious

or fatal injury to the operator or others. It is extremely important that you read and understand the contents of this operator's manual.

WARNING: Under no circum-

stances may the design of the machine be modified without the

permission of the manufacturer. Always use genuine accessories.

Non-authorized modifications and/or accessories can result in serious personal injury or the death of the operator or others.

Your warranty may not cover damage or liability caused by the

use of non-authorized accesso- ries or replacement parts.

Symbols

KEY TO SYMBOLS

WARNING: Clearing saws, brush- L_ cutters and trimmers can be dan- /m_k gerous! Careless or incorrect use J _

can result in serious or fatal / • _ injury to the operator or others.

Please read the operator's manual

carefully and make sure you [1'] I ri-] understand the instructions

before using the machine.

• A protective helmet where there is a risk of falling objects

Always wear: _)

• Hearing protection

• Approved eye protection

Max. speed of output shaft, rpm

msx

10000 rpm

Watch out for thrown objects and J_. ricochets.

The operator of the machine must ensure, while working, that no persons or animals

come closer than 50 feet

(15 meters).

Arrows which show limits for _,_ handle positioning.

Only intended for trimmer heads. _"

Other symbols/decals on the machine refer to special certification requirements

for certain markets.

Stop the engine by pushing and holding the stop switch

in the STOP position until the engine stops before carrying out any checks or maintenance.

Regular cleaning is required. [-_

Visual check.

always be used.

Approved eye protection must [_

Always wear approved protective gloves.

Wear sturdy, non-slip boots.

Only use non-metallic, flexible cutting attachments, i.e. trimmer

heads with trimmer line.

SAFETY INSTRUCTIONS

Personal protective equipment

IMPORTANT! Whenever you use a clear- ing saw, brushcutter or trimmer you must wear personal protective equipment that is

approved by the authorities. Personal protective equipment does not eliminate

the risk of accidents, but it can reduce the effects of an injury in the event of an acci- dent. Ask your dealer for help when

choosing protective equipment.

WARNING: Listen out for warn-

ing signals or shouts when you are

wearing hearing protection. Always

remove your hearing protection as soon as the engine stops.

GLOVES Gloves should be worn when necessary, e.g., when fitting cutting attachments.

HEARING PROTECTION

Wear hearing protection that provides adequate noise reduction.

EYE PROTECTION

Always wear approved eye protection, if you use a visor then you must also wear

approved protective goggles. Approved protective goggles must comply with

standard ANSI Z87.1.

FIRST AID KIT

Always have a first aid kit nearby.

Machine's safety equipment

This section describes the machine's safe- ty equipment, its purpose, and how checks

and maintenance should be carried out to ensure that it operates correctly. See the

"Know your trimmer" section to locate where this equipment is positioned on your

machine. The life span of the machine can be reduced

and the risk of accidents can increase if machine maintenance is not carried out

correctly and if service and/or repairs are not carried out professionally, if you need further

information please contact your nearest ser- vicing dealer.

_& WARNING: Never use a machine

that has faulty safety equipment!

Carry out the inspection, mainte- nance and service routines listed in

this section.

Throttle lock

The throttle _ock is designed to prevent ac- cidental operation of the throttle control When you press the lock (A) (i.e. when you

grasp the handle) it releases the throttle control (B). When you release the handle

the throttle controt and the throttle lock both move back to their original positions. This

movement is controlled by two independent return springs. This arrangement means

that the throttle control is automatically locked at the idle setting.

BOOTS Wear sturdy, non-slip boots.

CLOTHING Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy.

long pants. Do not wear jewelry, shorts sandals or go barefoot. Secure hair so it is

above shoulder level.

Stop switch Make sure the engine stops when you push

and hold the stop switch.

SAFETY INSTRUCTIONS

Cutting attachment guard

This guard is intended to prevent loose ob- jects from being thrown towards the opera-

tor. The guard also protects the operator from accidental contact with the cutting at- tachment.

_ ARNING: Never use a cutting

Use of incorrectly wound trimmer line or an incorrect cutting attachment increases the

level of vibration.

Muffler

The muffler is designed to reduce the noise level and to direct the exhaust gases away

from the operator.

CAUTION! Muffler is fitted with a catalytic converter designed to reduce harmful ex- haust gases.

For mufflers, it is very important that you fol- low the instructions on checking, maintain-

ing. and servicing your machine. See Checking, maintaining and servicing the

machine's safety equipment section.

\\ \

attachment without an approved guard. See the section on "Technical

data". If an incorrect or faulty guard is fitted this can cause serious

personal injury.

WARNING: Overexposure to

vibration can lead to circulatory damage or nerve damage in people who have impaired circulation.

Contact your doctor if you experi- ence symptoms of overexposure to vibration. Such symptoms include

numbness, loss of feeling, tingling, pricking, pain, loss of strength,

changes in skin color or condition. These symptoms normally appear in the fingers, hands or wrists. The

risk increases at low temperatures.

WARNING: Mufflers fitted with

catalytic converters get very hot

during use and remain so for some time after stopping. This also ap-

plies at idle speed. Contact can re- sult in burns to the skin. Remember

the risk of fire!

_tli WARNING: The inside of the

muffler contain chemicals that may be carcinogenic. Avoid contact with these elements in the event of a

damaged muffler.

WARNING: Bear in mind that:

Engine exhaust fumes contain car- bon monoxide, which can cause

carbon monoxide poisoning. For this reason you should not start or

run the machine indoors, or any-

where that is poorly ventilated. The exhaust fumes from the engine

are hot and may contain sparks which can start a fire. Never start the machine indoors or near com-

bustible material!

Cutting equipment

A trimmer head is intended for trimming grass.

Checking, maintaining and servicing the machine's

safety equipment

IMPORTANT! All servicing and repair work on the machine requires special training. This is especially

true of the machine's safety equipment. If your machine fails any of the checks de-

scribed below you must contact your service agent. When you buy any of our products we

guarantee the availabitity of professional re-

3airs and service. If the retailer who sells

your machine is not a servicing dealer, ask him for the address of your nearest service agent.

SAFETY INSTRUCTIONS

Throttle lock

• Make sure the throttle contro_ is locked at the idle setting when the throttle lock

is released.

• Press the throttle lock and make sure it

returns to its original position when you release it.

• Check that the throttle control and throttle lock move freely and that the

return springs work properly.

Stop switch

• Start the engh_e and make sure the engine stops when you push and hold the stop

switch.

Cutting attachment guard

• Ensure that the guard is undamaged and is not cracked.

• Replace the guard if it has been exposed

to impact or is cracked.

• Always use the recommended guard for

the cutting attachment you are using. See

section on "Technical data".

Muffler

• See instructions under the section "Start". Start the machine and apply full

throttle. Release the throttle and check that the cutting attachment stops and re-

mains at a standstill. If the cutting attach- ment rotates with the throttle in the idle

position then the carburetor idle setting must be checked. See instructions under

the section "Maintenance".

• Never use a machine that has a faulty muffler.

• Regularly check that the muffler is securely

attached to the machine.

• The muffler on this unit is equipped with a special spark arrestor mesh. The mesh

should be checked and, if necessary. cleaned by a servicing dealer. A blocked mesh will cause the machine to overheat,

which can lead to serious damage. Never

use a muffler with a defective spark arres-

tor mesh. See the Maintenance section.

SAFETY INSTRUCTIONS

Cutting equipment This section describes how to choose and

maintain your cutting equipment in order to:

• Obtain maximum cutting performance.

• Extend the life of cutting equipment. General rules:

Trimmer head

• Only use the recommended cutting at- tachments. See the section on "Technical data".

1. Only use cutting attachments with the guards we recommend! See the section

on "Technical Data".

2. Check the cutting attachment for damage or cracks. A damaged cutting attachment

should always be replaced.

_ WARNING: Never use a machine

with faulty safety equipment. The

machine's safety equipment must be checked and maintained as

described in this section. If your machine fails any of these checks contact your service agent to

get it repaired.

IMPORTANT!

This section describes how to choose and maintain your cutting equipment in order to:

Obtain maximum cutting performance. Extend the life of cutting equipment.

Only use cutting attachments with the guards we recommend! See the section on "Technical data",

Refer to the instructions for the cutting attach- ment to check the correct way to load the

trimmer line and the correct line diameter.

• Smaller machines generally require small trimmer heads and vice versa. This is be-

cause when clearing using trimmer line the engine must throw out the trimmer

line radially from the trimmer head and overcome the resistance of the grass

being cleared.

• The length of the trimmer line is also im- portant. A longer trimmer line requires

greater engine power than a shorter trimmer line of the same diameter.

• Make sure that the cutter on the trimmer guard is intact. This is used to cut the

trimmer line to the correct length.

• To increase the life of the trimmer line it can be soaked in water for a couple of

days. This will make the line tougher so that it lasts longer.

IMPORTANT!

Always ensure the trimmer line is wound tightly and evenly around the drum, other- wise the machine will generate harmful

vibration,

_ WARNING: Always stop the en-

gine before doing any work on the cutting attachment. This continues

to rotate even after the throttle has been released. Ensure that the

cutting attachment has stopped completely and disconnect the

lead from the spark plug before you start to work on it,

SAFETY INSTRUCTIONS

General safety precautions

IMPORTANT!

• The machine is only designed for trimming grass.

• The only accessories you can operate with this engine unit are the cutting at-

tachments we recommend in the "Tech-

nical data" section,

• Never use wire, rope, string, etc,

• Never use the machine if you are tired, if you have drunk alcohol, or if you are tak-

ing medication that could affect your vi-

sion, your judgment or your coordination,

• Never use the machine in extreme weath- er conditions such as severe cold, very hot

and/or humid climates.

• Never use a machine that has been modi- fied in any way from its original specifica-

tion,

• Wear personal protective equipment. See

instructions in the "Personal protective

equipment" section.

• Never use a machine that is faulty, Carry out the checks, maintenance and service

instructions described in this manual,

Some maintenance and service measures

must be carried out by trained and quali- fied specialists. See instructions in the "Maintenance" section,

• All covers and guards must be fitted before starting, Make sure the spark plug cap and

lead are not damaged. Otherwise you

could get an electric shock.

• The machine operator must ensure that

no people or animals come closer than

50 feet (15 meters) while working,

• Stay clear of spinning line,

• Secure or remove loose clothing or cloth-

ing with loosely hanging ties, straps, tas-

sels, etc. They can be caught in moving

parts,

• Being fully covered also helps protect you from debris and pieces of toxic plants

thrown by spinning line.

• Keep handles free of oil and fuel,

• Always keep the engine on the right hand side of your body,

• Hold the unit firmly with both hands.

• Keep trimmer head below waist level and away from all parts of your body, Do not

raise engine above your waist.

• Keep all parts of your body away from

muffler and spinning line. Keep engine be- low waist level. A hot muffler can cause

serious burns.

• Keep firm footing and balance. Do not overreach or use from unstable surfaces

such as ladders, trees, steep slopes, roof- tops, etc,

• Use only in daylight or good artificial light.

• Use only for jobs explained in this manual,

tachment may increase the risk of

,_ WARNING: A faulty cutting at- I

accidents.

Personal protection

• Always wear boots and other equipment described

in the "Personal protective equipment" section.

• Always wear working clothes and heavy-duty long pants,

• Never wear loose fitting clothes or jewelry.

• Persons with long hair should (for personal safety) put their hair up.

Safety instructions regarding the

surroundings

• Never allow children to use the machine,

• Ensure no one comes closer than 50 feet (15 meters) when working.

• Never allow anyone else to use the machine without first ensuring that they

have understood the contents of the operator's manual.

Safety instructions before starting work

• Inspect the working area, Remove any objects such as stones, broken glass,

nails, steel wire, string, etc. that can be thrown or can wrap around the cutting head or shaft.

• Keep others at a safe distance, Children, animals, onlookers and helpers should

stand outside of the safety zone of 50 feet (15 meters), Stop the machine im- mediately if anyone should approach,

• Check the entire machine before starting work. Replace damaged parts. Check for

fuel leakage and that all safety guards and covers are complete and fastened securely. Check all nuts and bolts.

Check the cutting head "-\_

damage.

i or cracks or any other _.

Ensure the trimmer guard "_ _" is mounted and not

damaged,

SAFETY INSTRUCTIONS

• Check that the trimmer head and guard are correctly secured.

• When adjusting the carburetor, make sure the lower end is supported and that no one

is in the immediate vicinity.

• Make sure the cutting head does not rotate when idling.

• Make sure the handle and safety features are in order. Never use a machine that has

parts missing or has been changed in relation to the specification.

• Only use the machh_e for the purpose for which it was intended.

Starting

WARNING: When the engine is I

started with the choke in either the I choke or start throttle positions the I cutting attachment will start to rotate immediate y.

Ensure that alt of the engine covers and housings are properly fitted before the unit is started.

• Never start or attempt to run the unit with the clutch, clutch drum, clutch cover, or

driveshaft removed.

• Never start the machine indoors. Exhaust fumes can be dangerous if inhated.

• Observe your surroundings and make sure that there is no risk of people or animals

coming into contact with the cutting equip- ment.

• See the "Starting and Stopping" section for

complete instructions.

Fuel safety

• Always use a fuel container with an anti- spill valve.

• Never refuel the machine while the engine

is running.

• Always stop the engine and let it cool for a few minutes before refueling.

• Make sure there is plenty of ventilation when refueling or mixing fuel (gasoline and

2-stroke oil).

• Move the machine at least 10 feet (3 me- ters) from the refueling point before start-

ing_ it. "== mt'llll_

\ _-_,_ Min. 1Oft.

• Never start the machine:

• If you have spilled fuel on it. Wipe off the spillage and allow remaining fuel to

evaporate.

• if you have spilled fuel on yourself or your clothes, change your clothes. Wash

any part of your body that has come in contact with fuel. Use soap and water.

• if the machine is leaking fuel. Check regularly for leaks from the fuel cap

and fuel lines.

• Avoid all skin contact with fuel. Fuel is a skin irritant and may even cause skin changes.

Transporting and storage

• Store and transport the machine and fuet so that there is no risk of any leakage or

fumes coming into contact with sparks or naked flames, for example, from electri-

cal machinery, electric motors, electrical relays/switches or boilers.

• When storing and transporting fuel al- ways use approved containers intended

for this purpose. When storing the machine for long peri- ods the fuel tank must be emptied. Con-

tact your local gas station to find out where to dispose of excess fuel.

dling fuel. Bear in mind the risk of WARNING: Take care when ban- I

fire, explosion and inhaling fumes.

General working instructions

IMPORTANT! This section describes the basic safety pre- cautions for working with trimmers. If you

encounter a situation where you are uncer- tain how to proceed you should ask an ex- pert. Contact your servicing dealer.

Avoid all usage which you consider to be beyond your capability.

You must understand the difference between forestry clearing, grass clearing and grass trimming before use.

Basic safety rules

/t,@

1. Look around you:

• To ensure that people, animals or other

things cannot affect your control of the machine.

• To ensure that people, animals, etc.,

do not come into contact with the cut- ting attachment or loose objects that are thrown out by the cutting attach-

ment.

SAFETY INSTRUCTIONS

• CAUTION! Do not use the machine unless you are able to call for help in

the event of an accident.

2. Do not use the machine in bad weather, such as dense fog, heavy rain, strong

wind, intense cold, etc. Working in bad weather is tiring and often brings added

risks, such as icy ground, unpredictable felling direction, etc.

3. Make sure you can move and stand safely. Check the area around you for possible ob-

stacles (roots, rocks, branches, ditches, etc.) in case you have to move suddenly. Take

great care when working on sloping ground.

4. Switch off the engine before moving to another area,

5. Never put the machine clown with the engine running.

Basic working techniques

• Always slow the engine to idle speed after

each working operation. Long periods at full throttle without any load on the engine

can lead to serious engine damage.

• It is recommended that the engine not

be operated for longer than 1 minute at

full throttle,

or grass get caught between the guard and cutting attachment.

_ ARNING: Sometimes branches

Always stop the engine before

cleaning.

Grass trimming using a trimmer head Trimming

@@@

• Hold the trimmer head just above the

ground at an angle. It is the end of the trim- mer line that does the work. Let the trim-

mer line work at its owe pace. Never press the trimmer line into the area to be cut.

• Reduce the risk of damaging plants by shortening the trimmer line to 4-4 1/2 inches

(10-12 cm) and reducing the engine speed.

• When trimming you should use less than

full throttle so that the trimmer line lasts longer and to reduce the wear on the

trimmer head.

Clearing

• The clearing technique removes all un- wanted vegetation. Keep the trimmer

head just above the ground and tilt it. Let

the end of the trimmer line strike the ground around trees, posts, statues and

the like. CAUTION! This technique

increases the wear on the trimmer line.

4 1,,!1

• The trimmer line wears quicker and must

be fed forward more often when working

against stones, brick, concrete, metal fences, etc., than when coming into con-

tact with trees and wooden fences.

Cutting

@@@

• The trimmer is ideal for cutting grass that

is difficult to reach using a normai lawn mower. Keep the trimmer line parallel to

the ground when cutting. Avoid pressing the trimmer head against the ground as

this can ruin the lawn and damage the tool.

_l_'_ ,_e,_V_,-_'._ 1q'_ ',-

Do not allow the trimmer head to con- stantly come into contact with the ground

during normal cutting. Constant contact of this type can cause damage and wear

to the trimmer head.

• The trimmer line can easily remove grass and weeds up against walls, fences, trees and borders, however it can also damage

sensitive bark on trees and bushes, and damage fence posts.

SAFETY INSTRUCTIONS

Sweeping

QOO

• The fan effect of the rotating line can be used for quick and easy clearing up.

Hold the trimmer line parallel to and

above the area to be swept and move the tool to and fro.

• When cutting and sweeping you should use full throttle to obtain the best results.

i_ WARNING: Neither the operator

of the machine nor anyone else may attempt to remove the cut material

while the engine is running or the trimmer line is rotating, as this can

result in serious injury. Stop the engine and trimmer head before you

remove material that has wound around the drive shaft as otherwise

there is a risk of injury. The bevel gear can get hot during use and may remain so for a while afterwards. You

could get burned if you touch it.

WARNING: Watch out for thrown

objects. Always wear eye protection. Never lean over the cutting attach-

ment guard. Stones, rubbish, etc. can be thrown up into the eyes

causing blindness or serious injury.

Keep unauthorized persons at a dis- tance. Children, animals, onlookers

and helpers should be kept outside the safety zone of 50 feet (15 meters).

Stop the machine immediately if anyone approaches.

KNOW YOUR TRIMMER

Know your trimmer

1. Trimmer head

2. Grease filler cap

3. Bevel gear

4. Cutting attachment guard

5. Upper shaft

6. Lower shaft

7. Loop handle

8. Throttle control

9. Stop switch

10.Throttle lock

11.Cylinder cover

12. Starter handle

13. Fuel tank

14. Choke control

15. Primer bulb

16. Air filter cover

17. Handle adjustment

18. Drive disc

19. Shaft coupling

20. 2-stroke engine oil

21. Operator's manual (EPA)

ASSEMBLY

NOTE: Make sure unit is assembled cor- rectly as shown in this manual.

Fitting the loop handle

• Position the handle on the upper shaft. Note that the handle must be mounted

between the two arrows on the shaft.

• Fit the screw, securing plate and wing nut as shown h_the diagram.

• Tighten the wing nut.

Assembling and dismantling the two-piece shaft

Dismantling:

• Loosen the coupling by turning the knob.

• Press and hold the locking/release but- ton (A).

• While securely holding the engine and upper shaft, pull the attachment straight

out of the coupling.

Assembly:

• Loosen the coupling by turning the knob.

• Position locking/release button (A) of attachment into guide recess (B) of

coupling.

• Push the attachment into the coupling

until the locking/release button snaps into the primary hole (C).

• Before using the unit, tighten the knob

securely.

designed to be used in the primary hole unless otherwise stated in the

applicable attachment instruction manual. Using the wrong hole could

I_ WARNING: All attachments are

lead to serious injury or damage to

the unit,

Fitting the trimmer guard and

trimmer head

• Fit the correct trimmer guard (D) for use with the trimmer head. Hook the trimmer

guard/combination guard onto the fitting

on the shaft and secure with the bolt (E),

'_'_ E F

D D

• Fit the drive disc (F) on the output shaft.

• Turn the shaft until one of the holes in the drive disc aligns with the corresponding

hole in the gear housing,

• insert hex wrench (G) in the hole to lock the shaft,

• Screw on the trimmer head (H) in the op-

posite direction to the direction of rota-

tion,

• To dismantle, follow the instructions in the reverse order.

FUEL HANDLING

Fuel mixture

CAUTION! The machine is equipped with a two-stroke engine and must always be

run using a mixture of gasoline and two- stroke engine oil, It is important to accu-

rately measure the amount of oil to be mixed to ensure that the correct mixture is

obtained. When mixing small amounts of fuel, even small inaccuracies can drastical-

ly affect the ratio of the mixture.

there is adequate ventilation when

&WARNING: Always ensure

handling fuel.

Gasoline

CAUTION! Always use high quality unleaded gasoline.

• This engine is certified to operate on

unleaded gasoline.

• The lowest recommended octane rating is 87. If you run the engine on lower oc-

tane rating than 87, "knocking" can oc- cur, This leads to an increased engine

temperature, which can result in a seri- ous engh_e breakdown,

• When working at continuous high revs a higher octane rating is recommended,

Two-stroke oil

• For great results and performance use HUSQVARNA two-stroke oil, which is

specially formulated for our two-stroke engh_es, Mixture 1:50 (2%),

• To maximize the life of your trimmer, you may choose to use a high quality syn-

thetic oil formulated for two-stroke

engh_es, Mixture 1:50 (2%),

• Never use two-stroke oil intended for

water-cooled outboard engines, sometimes referred to as outboard oil.

• Never use oil h_tended for four-stroke engh_es.

• Always start by filing half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture.

Add the remaining amount of gasoline.

• Mix (shake) the fuel mixture thoroughly

before filling the machine's fuel tank.

• Do not mix more than one month's sup-

ply of fuel at a time.

• If the machine is not used for some time, the fuel tank should be emptied and

cleaned.

WARNING: The catalytic con-

verter muffler gets very hot during and after use. This also applies

during idling. Be aware of the fire

hazard, especially when working near flammable substances and/or

vapors.

Fueling

WARNING: Taking the following

precautions, will lessen the risk of fire:

Do not smoke or place hot objects near fuel.

Always shut off the engine before refueling.

Always stop the engine and let it cool for a few minutes before refu-

elling.

When refueling, open the fuel cap slowly so that any excess pressure is released gently.

Tighten the fuel cap carefully after refueling.

Always move the machine away from the refueling area before starting.

Gasoline 2% (1:50)

U.S. gallon U.S. fl. oz.

1 2 t/2 2 1/2 6 1/2 5 12 7/8

Mixing

• Always mix the gasoline and oil in a clean container intended for fuel

Two-stroke oil

• Clean the area around the fuel cap. Contamination in the tank can cause

operating problems.

• Ensure that the fuel is well mixed by shak- ing the container before filling the tank.

STARTING AND STOPPING

Check before starting

• Inspect the unit before each use. Re-

place damaged parts. Check for fuel leaks. Make sure all fasteners are in

place and secure, Make sure the cutting

attachment is properly installed and se- curely fastened, Use only flexible, non-

metallic line recommended by the

manufacturer, Never use, for example, wire or wire rope, which can break off and become a dangerous projectile.

• Check that the trimmer head and trimmer guard are not damaged or cracked,

Replace the trimmer head or trimmer

guard if they have been exposed to

impact or are cracked,

• Never use the machine without a guard

nor with a defective guard,

Starting and stopping

@00

WARNING: The complete clutch,

clutch cover, and shaft must be fitted before the machine is started,

otherwise parts could come loose and cause personal injury. Always move the machine away

from the refueling area before starting. Place the machine on a flat surface. Ensure the cutting at-

tachment cannot come into contact with any object.

Make sure no unauthorized persons are in the working area, otherwise there is a risk of serious personal

injury. The safety distance is 50 feet (15 meters).

Cold engine Primer bulb: Press the primer bulb 10

times until fuel begins to fill the bulb. The primer bulb need not be completely filled.

Choke: Move the blue engine choke lever over to the closed position.

_ _t J_r _'_ _

Starting

Hold the body of the machine on the ground using your Ieff hand (CAUTION!

Not with your foot!), Firmly grip the starter rope handle with your right hand. DO NOT squeeze

throttle trigger, Slowly pull out the cord until you feel some resistance (the starter pawls grip); then quickly and powerfully

pull the cord.

Never wrap the starter cord around

your hand.

Repeat pulling the cord until the engine attempts to start, Squeeze throttle trigger to release the choke. Continue to hold

throttle trigger and pull starter rope until engine runs,

NOTE: If engine dies, return blue engine choke lever to the closed position and

repeat starting steps,

CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended.

This can damage the machine.

STARTING AND STOPPING

Warm engine

With a warm engine, squeeze and hold the throttle trigger, Pull starter rope sharply while squeezing throttIe trigger until engine

runs.

Stopping

Stop the engine by pushing and holding the stop switch in the STOP position until the engine stops.

WARNING: When the engine is I

started with the choke in the closed I position the cutting attachment will

start to rotate immediate y.

MAINTENANCE

The owner is responsible for the perfor-

mance of all required maintenance as

defined in the operator's manual.

Carburetor

Your Husqvama product has been designed and manufactured to specifications that re- duce harmful emissions. After the engine

has used 8-10 tanks of fueI, the engine will be run-in. To ensure that it continues to run

at peak performance and to minimize harm- ful exhaust emissions after the run-in peri-

od, ask your servicing dealer to adjust your carburetor.

_lb WARNING: The complete clutch,

clutch cover, and shaft must be I fitted before the machine is started, I

otherwise parts could come loose and cause persona injury.

Function

• The carburetor governs the engine's

speed via the throttte control. Air and fuel are mixed in the carburetor.

• The T-screw regulates the throttle setting at idle speed. If the T-screw is turned

clockwise this gives a higher idle speed;

turning it counterclockwise gives a lower

idle speed.

Basic setting

• The basic carburetor settings are ad-

justed during testing at the factory. Fine

adjustment should be carried out by a skilled technician.

CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment

screw T should be turned counterclockwise until the cutting attachment stops.

Rec. idle speed:

See "Technical data" section.

Recommended max. speed:

See "Technical data" section.

cannot be adjusted so that the cut- ting attachment stops, contact your

dealer/service workshop. Do not use the machine until it has been cor-

_ WARNING: If the idle speed

rectly adjusted or repaired.

Fine adjustment of the idle speed-T

Adjust the idle speed using the idle adjust- ment screw-T if it is necessary to readjust.

First, turn the idle adjustment screw-T clockwise until the cutting attachment starts

to rotate. Then, turn the screw counterc- lockwise until the cutting attachment stops.

The idle speed is correctly adjusted when the engine will run smoothly in every posi-

tion. The idle speed should also be well

below the speed at which the cutting at-

tachment starts to rotate.

Idle Speed Screw-T

WARNING: If the idle speed can-

not be adjusted so that the cutting attachment stops, contact your ser- vicing dealer. Do not use the ma-

chine until it has been correctly ad- justed or repaired.

Unit/Maintenance Safety

Disconnect the spark plug before perform- ing maintenance, except carburetor adjust-

ments.

Muffler

CAUTION! Muffler is fitted with a catalytic converter designed to reduce harmful ex-

haust gases.

The muffler is designed to reduce the noise level and to direct the exhaust gases away

from the operator. The exhaust gases are hot and can contain sparks, which may

cause fire if directed against dry and com- bustible material.

Mufflers are equipped with a special spark arrestor mesh. The mesh should be

checked and, if necessary, cleaned by a servicing dealer. If the mesh is damaged,

it should be replaced, if the mesh is fre- quently blocked, this can be a sign that the

performance of the catalytic converter is impaired. Contact your servicing dealer to

inspect the muffler. A blocked mesh will cause the machine to overheat and result

in damage to the cylinder and piston,

MAINTENANCE

Muffler bolts

i j[__l Sparkarrestor mesh

CAUTION! Never use a machine that has a faulty or loose muffler. Ensure the muffler

bolts are tight.

catalytic converters get very hot during use and remain so for some

time after stopping. This also ap- plies at idle speed. Contact can re-

l& ARNING: Mufflers fitted with

sult in burns to the skin. Remember the risk of fire!

muffler contain chemicals that may be carcinogenic. Avoid contact with

these elements in the event of a

WARNING: The inside of the I

damaged muffler.

WARNING: Bear in mind that:

Engine exhaust fumes contain car- bon monoxide, which can cause

carbon monoxide poisoning. For this reason you should not start or run the machine indoors, or any-

where that is poorly ventilated. The exhaust fumes from the engine are hot and may contain sparks

which can start a fire. Never start the machine indoors or near com-

bustible material!

Spark plug

0.024" (0.6 ram)

Two-piece shaft

The drive shaft end in the lower shaft should be lubricated with grease every 30

hours. There is a risk that the drive shaft ends (splined coupling) will seize if they

are not lubricated regularly.

Air filter

The air filter must be regularly cleaned to

remove dust and dirt in order to avoid:

• Carburetor malfunctions

• Starting problems

• Loss of engine power

• Unnecessary wear to engine parts

• Excessive fuel consumption

The spark plug condition is influenced by:

• Incorrect carburetor adjustment.

• An incorrect fuel mixture (too much or in- correct type of oil).

• A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operat- ing problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always

check the spark plug first before taking any further action. Ifthe spark plug is dirty, clean it and check that the electrode gap is

0.024" (0.6 mm). The spark plug should be

replaced after about a month in operation or earlier if necessary.

CAUTION! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder.

Clean the filter every 25 hours, or more

regularly if conditions are exceptionally

dusty.

Cleaning the air filter

Remove the air filter cover and take out the

filter, Wash it clean in warm, soapy water.

Rinse thoroughly. Ensure that the filter is dry

before refitting it. An air filter that has been in use for a long time cannot be cleaned completely. The

filter must therefore be replaced with a new one at regular intervals. A damaged air

filter must always be replaced,

MAINTENANCE

Bevel gear

The bevel gear is filled with the right quantity of grease at the factory. However, before

ush_g the machine you should check that the bevel gear is filled three-quarters

full with grease. Use HUSQVARNA special grease.

The grease in the bevel gear does not nor- mally need to be changed except if repairs are carried out.

Maintenance schedule

Below you will find some generai mainte- nance instructions.

Daily maintenance

• Check throttle trigger and throttle trigger lockout function.

• Check that the stop switch works

correctly.

• Check that there are no fuel leaks from

the engine, tank or fuel lines.

• Check that the cutter does not rotate

when the engine is idling.

• Clean the outside of the machine.

• Check that the harness is not damaged.

• Check that the cutting attachment guard is not damaged or cracked.

• Replace the guard if it is exposed to im- pact or is cracked.

• A non-balanced trimmer head induces heavy vibrations that may damage the

machine.

• Check that nuts and screws are tight.

• Check that the screws that hold the bevel

gear are tight.

• Check that the trimmer head is tight.

Weekly maintenance

• Check the starter and starter cord.

• Clean the carburetor area.

• Clean the outside of the spark plug. Re- move it and check the electrode gap. Ad-

just the gap to 0.024" (0.6 mm). or

replace the spark plug. Use resistor spark plug Champion RCJ-8Y or equivalent.

• Clean the cooling fins on the cylinder and check that the air intake near the starter

is not blocked.

• Check that the bevel gear is filled with grease up to 3/4 full. Use special grease.

• Clean the air filter.

Monthly maintenance

• Clean the fuel tank.

• Clean the outside of the carburetor and the space around it.

• Clean the fan and the area around it.

• Check fuel lines for cracks or other dam- age. Change if necessary.

• Change the fuel filter in fuel tank.

• Check the clutch, clutch springs and the clutch drum for wear. Replace if neces- sary.

• Check electrical wires and connections.

• Replace the spark plug. Use resistor spark plug Champion RCJ-8Y or equiva-

lent.

• Change the air filter.

Trimmer Head Line Loading Instructions _

_1_

20'

"CI;ck"

TECHNICAL DATA

Technical data

Engine

Cylinder volume, cu.in./cm 3 1.7/28 Cylinder bore, inch/mm 1.4/35

Stroke, inch/ram 1.130/28.7 Idle speed, rpm 2,800-3,200 Recommended max. speed, rpm 10,000

Speed of output shaft, rpm 8,000 Max. engine output, acc. to ISO 8893, hp/kW 1.1/0.8 Catalytic converter muffler Yes Speed-regulated ignition system Yes Ignition system Manufacturer/type of ignition system Spark plug

Electrode gap, inch/mm Fuel and lubrication system

Manufacturer/type of carburetor Zama Fuel tank capacity, US pint/liter 0.85/0.4 Weight Weight without fuel, cutting attachment and guard, Ibs/kg 11/5.0 Sound levels

(see note 1) Equivalent sound pressure level at the user's ear,

measured according to ANSI B175.3-1997, dB(A), min/max: 94/97

Vibration levels Vibration leve_s at handles, measured according to ANSi

B175.3-1997, m/s 2 At idle, left/right handles: 3/5

At max. speed, left/right handles: 9/8

Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various working conditions with the following time distribution:

1/2 idle and 1/2 max. speed.

NOTE! Noise pressure at the user's ear and vibration on the handles are measured with all the machine's approved cutting equipment fitted. The table indicates the highest and lowest values.

125LD

Wabro/CD

Champion RCJ-8Y

0.024/0.6

Model 125LD (MIO LH arbor shaft thread)

I ceaao"os ZJ_ o

Trimmer head I T25

Attachments

Edger attachment with shaft Cultivator attachment with shaft

Pruner attachment with shaft

hment guard, part. no.

Part. no.

952 715 596 952 715 492 952 715 491

WARRANTY STATEMENT

SECTION 1: LIMITED WARRANTY Husqvarna Forest & Garden Company

("Husqvarna') warrants Husqvarna product to the original purchaser to be free from de-

fects in matefiaI and workmanship from the date of purchase for the '_/arranty Period" of the products as set forth below:

Lifetime Warranty: Trimmer shafts, ignition coils and modules.

2 Year NON-COMMERCIAL Warranty: Trimmers for non-commercial, non-profes- sional, non-institutional or non-income pro-

ducing use, except as herein stated. Emission control system components neces-

sary to comply with CARB-TIER II and EPA regulations. 1 Year Warranty: All trimmers used for

commercial, institutional, professional, or in- come producing purposes or use.

SECTION 2: HUSQVARNA'S OB- LIGATIONS UNDER THE WARRANTY

Husqvarna will repair or replace defective components without charge for parts or labor

if a component fails because of a defect in material or workmanship during the warranty

period. SECTION 3: ITEMS NOT COVERED

BY THIS WARRANTY The following items are not covered by this

warranty: (1) Normal customer maintenance items

which become worn through normal regu-

lar use, including, but not limited to, filters, lubricants, rewind springs, spark plugs,

and starter ropes.

(2) Natural discoloration of material due to

ultraviolet light.

SECTION 4: EXCEPTIONS AND LIMITATIONS

This warranty shall be inapplicable to de- fects resulting from the following:

(1) Accident, abuse, misuse, negligence and

neglect, including stale fuel, dirt, abra-

sives, moisture, rust, corrosion, or any adverse reaction due to incorrect storage

or use habits.

(2) Failure to operate or maintain the unit in

accordance with the operator's manual or

instruction sheet furnished by Husqvarna.

(3) Alterations or modifications that change

the intended use of the product or affects the product's performance, operation,

safety, or durability, or causes the product to fail to comply with any applicable laws.

(4) Additional damage to parts or compo-

nents due to continued use occurring af-

ter any of the above.

REPAIR OR REPLACEMENT AS PRO-

VIDED UNDER THIS WARRANTY IS THE

EXCLUSIVE REMEDY OF THE PURCHAS- ER. HUSQVARNA SHALL NOT BE LIABLE

FOR ANY INCIDENTAL OR CONSEQUEN-

TIAL DAMAGES FOR BREACH OF ANY

EXPRESS OR IMPLIED WARRANTY ON

THESE PRODUCTS EXCEPT TO THE EX- TENT PROHIBITED BY APPLICABLE LAW.

ANY IMPUED WARRANTY OR MER- CHANTABIUTY OR FITNESS FOR A PAR-

TICULAR PURPOSE ON THESE PROD- UCTS IS LIMITED iN DURATION TO THE

WARRANTY PERIOD AS DEFINED IN THE

LIMITED WARRANTY STATEMENT HUBQ- VARNA RESERVES THE RIGHT TO CHANGE OR iMPROVE THE DESIGN OF

THE PRODUCT WITHOUT NOTICE, AND

DOES NOT ASSUME OBLIGATION TO UP-

DATE PREVIOUSLY MANUFACTURED

PRODUCTS. Some states do not allow the exclusion of in- cidental or consequential damages, or limita- tions on how long an implied warranty lasts, so the above limitations or exclusions may not

apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

SECTION 5: CUSTOMER RE- SPONSIBILITIES

The product must exhibit reasonable care, maintenance, operation, storage and gener- al upkeep as written in the maintenance

section of the operator's manual. Should an operational problem or failure occur, the

product should not be used, but delivered as is to an authorized Husqvarna dealer for evaluation. Proof of purchase, as explained

in Section 6, rests solely with the customer. SECTION 6: PROCEDURE TO OB-

TAIN WARRANTY CONSIDERATION

It is the Owner's and Dealer's responsibility to make certain that the Warranty Registration Card is properly filled out and mailed to Husq-

varna Forest & Garden Company. This card

should be mailed within ten (10) days from the date of purchase in order to confirm the war-

rarity and to facilitate post-sale service.Proof of purchase must be presented to the autho-

rized Husqvama dealer in order to obtain war- ranty service. This proof must include date purchased, model number, serial number, and

complete name and address of the selling dealer.To obtain the benefit of this warranty, the product believed to be defective must be

delivered to an authorized Husqvarna dealer

in a timely manner, no later than thirty (30) days from date of the operational problem or

failure. The product must be delivered at the

owner's expense. Pick-up and delivery charges are not covered by this warranty. An

authorized Husqvama dealer can be normally

located through the 'Yellow Pages" of the lo-

cal telephone directory or by calling

1-800-HUSKY62 for a dealer in your area.

6 Husqvarna

7349 Statesville Road

CHARLOTTE, NC 28269

+ 50 hidden pages