Husky 7214, 8413 Owner's Manual

Model #7214 & #8413

Recommended Installation, Maintenance

and Inspection Instructions

Diesel Exhaust Fluid (DEF) Adaptor

Important safety InstructIons - save these InstructIons In a readIly accessIble locatIon.

7214 &

WARNING: For use on non-electrically conductive installations only!

INSTALLATION INSTRUCTIONS

NOTE: Always adhere to installation / usage instructions and warning. Improper use may result in injury, damage or hazardous spill.

1. Turn off dispenser and relieve line pressure.

2. Slide clamp onto the DEF compatible exible tubing (¾ in / 19 mm ID x ⅛ in / 3.1 mm wall thickness) - do not tighten.

3. Slide tubing and clamp over the hose barb end of the DEF adaptor until hose bottoms out at the adaptor ange.

4. Position clamp between the adaptor ange and the rst adaptor barb.

5. Tighten clamp by applying approximately 540 lbf•ft / 2400 N•m to clamp ear. Conrm clamp is tight by visually inspecting the dimple formation.

6. Only connect to DEF compatible and 304 stainless steel ttings - see page 2 for applicable seal congurations.

7. Do not use thread sealant (Teon tape, anti-seize or any other kind of sealant).

8. Install at the nozzle.

9. Tighten rmly, approximately 15 - 20 lbf•ft / 20.3 - 27 N•m, but do not overtighten.

10. Pressurize system and visually inspect for leaks.

DO NOT OVERTIGHTEN

8413

IF DRIVE OFF OCCURS

• Turn off dispenser and relieve line pressure.

• Inspect the entire dispensing system for damage.

• Pressurize system and visually inspect for leaks.

TESTING / MAINTENANCE / INSPECTION

• All drive aways, maintenance and

Daily

• Check for leaks / stains

• Check for damage

• Only clean / rinse exterior surfaces of DEF product with deionized water.

inspection activities must be logged using the serial number of the individual product.

• Apply city, state, or federal testing regulations as appropriate.

ANY TEST / INSPECTION FAILURE

REQUIRES IMMEDIATE EQUIPMENT

REPLACEMENT OR REMOVAL

FROM SERVICE.

MADE IN THE USA

Husky Corporation • 2325 Husky Way • Pacic, MO 63069 • Phone: (800) 325-3558 • Fax: (636) 825-7300 • www.husky.com

Page 1 009250-4 9/2011

APPLICABLE SEAL CONFIGURATIONS

Model #7214 Adaptor thread type: ¾ x 14 Male BSPP one end; ¾ Hose Barb other end. Model #8413 Adaptor thread type: 1 X 11 Male BSPP one end; ¾ Hose Barb other end.

Option 1

▪ Seal is in mating device port. ▪ Husky gasket or o-ring seal not

required.

Hose BSPP port

Hose BSPP port compression seal (Figure 1.1)

Figure 1.1 Hose BSPP port compression seal (installed in hose port)

Option 3

▪ Seal formed by Husky gasket. ▪ Husky o-ring not required. ▪ Thread Husky gasket onto BSPP

tting plug. Do no press on.

Husky BSPP tting plug

Option 2

▪ Seal formed by Husky o-ring. ▪ Husky gasket not required.

Flange surfaces must mate

Figure 2.1 Husky o-ring compression seal

Mating Device BSPP port

Husky o-ring compression seal (Figure 2.1)

Husky BSPP tting plug

Husky gasket compression seal (Figure 3.1)

Husky BSPP tting plug

Figure 3.1 Husky BSPP gasket compression seal

Husky Corporation • 2325 Husky Way • Pacic, MO 63069 • Phone: (800) 325-3558 • Fax: (636) 825-7300 • www.husky.com

Page 2 009250-4 9/2011

+ 1 hidden pages